RFC 1323
Network Working Group V. Jacobson
Request for Comments: 1323 LBL
Obsoletes: RFC 1072, RFC 1185 R. Braden
ISI
D. Borman
Cray Research
May 1992
TCP Extensions for High Performance
Status of This Memo
This RFC specifies an IAB standards track protocol for the Internet
community, and requests discussion and suggestions for improvements.
Please refer to the current edition of the "IAB Official Protocol
Standards" for the standardization state and status of this protocol.
Distribution of this memo is unlimited.
Abstract
This memo presents a set of TCP extensions to improve performance
over large bandwidth*delay product paths and to provide reliable
operation over very high-speed paths. It defines new TCP options for
scaled windows and timestamps, which are designed to provide
compatible interworking with TCP's that do not implement the
extensions. The timestamps are used for two distinct mechanisms:
RTTM (Round Trip Time Measurement) and PAWS (Protect Against Wrapped
Sequences). Selective acknowledgments are not included in this memo.
This memo combines and supersedes RFC-1072 and RFC-1185, adding
additional clarification and more detailed specification. Appendix C
summarizes the changes from the earlier RFCs.
TABLE OF CONTENTS
1. Introduction ................................................. 2
2. TCP Window Scale Option ...................................... 8
3. RTTM -- Round-Trip Time Measurement .......................... 11
4. PAWS -- Protect Against Wrapped Sequence Numbers ............. 17
5. Conclusions and Acknowledgments .............................. 25
6. References ................................................... 25
APPENDIX A: Implementation Suggestions ........................... 27
APPENDIX B: Duplicates from Earlier Connection Incarnations ...... 27
APPENDIX C: Changes from RFC-1072, RFC-1185 ...................... 30
APPENDIX D: Summary of Notation .................................. 31
APPENDIX E: Event Processing ..................................... 32
Security Considerations .......................................... 37
Jacobson, Braden, & Borman [Page 1]
RFC 1323 TCP Extensions for High Performance May 1992
Authors' Addresses ............................................... 37
1. INTRODUCTION
The TCP protocol [Postel81] was designed to operate reliably over
almost any transmission medium regardless of transmission rate,
delay, corruption, duplication, or reordering of segments.
Production TCP implementations currently adapt to transfer rates in
the range of 100 bps to 10**7 bps and round-trip delays in the range
1 ms to 100 seconds. Recent work on TCP performance has shown that
TCP can work well over a variety of Internet paths, ranging from 800
Mbit/sec I/O channels to 300 bit/sec dial-up modems [Jacobson88a].
The introduction of fiber optics is resulting in ever-higher
transmission speeds, and the fastest paths are moving out of the
domain for which TCP was originally engineered. This memo defines a
set of modest extensions to TCP to extend the domain of its
application to match this increasing network capability. It is based
upon and obsoletes RFC-1072 [Jacobson88b] and RFC-1185 [Jacobson90b].
There is no one-line answer to the question: "How fast can TCP go?".
There are two separate kinds of issues, performance and reliability,
and each depends upon different parameters. We discuss each in turn.
1.1 TCP Performance
TCP performance depends not upon the transfer rate itself, but
rather upon the product of the transfer rate and the round-trip
delay. This "bandwidth*delay product" measures the amount of data
that would "fill the pipe"; it is the buffer space required at
sender and receiver to obtain maximum throughput on the TCP
connection over the path, i.e., the amount of unacknowledged data
that TCP must handle in order to keep the pipeline full. TCP
performance problems arise when the bandwidth*delay product is
large. We refer to an Internet path operating in this region as a
"long, fat pipe", and a network containing this path as an "LFN"
(pronounced "elephan(t)").
High-capacity packet satellite channels (e.g., DARPA's Wideband
Net) are LFN's. For example, a DS1-speed satellite channel has a
bandwidth*delay product of 10**6 bits or more; this corresponds to
100 outstanding TCP segments of 1200 bytes each. Terrestrial
fiber-optical paths will also fall into the LFN class; for
example, a cross-country delay of 30 ms at a DS3 bandwidth
(45Mbps) also exceeds 10**6 bits.
There are three fundamental performance problems with the current
TCP over LFN paths:
Jacobson, Braden, & Borman [Page 2]
RFC 1323 TCP Extensions for High Performance May 1992
(1) Window Size Limit
The TCP header uses a 16 bit field to report the receive
window size to the sender. Therefore, the largest window
that can be used is 2**16 = 65K bytes.
To circumvent this problem, Section 2 of this memo defines a
new TCP option, "Window Scale", to allow windows larger than
2**16. This option defines an implicit scale factor, which
is used to multiply the window size value found in a TCP
header to obtain the true window size.
(2) Recovery from Losses
Packet losses in an LFN can have a catastrophic effect on
throughput. Until recently, properly-operating TCP
implementations would cause the data pipeline to drain with
every packet loss, and require a slow-start action to
recover. Recently, the Fast Retransmit and Fast Recovery
algorithms [Jacobson90c] have been introduced. Their
combined effect is to recover from one packet loss per
window, without draining the pipeline. However, more than
one packet loss per window typically results in a
retransmission timeout and the resulting pipeline drain and
slow start.
Expanding the window size to match the capacity of an LFN
results in a corresponding increase of the probability of
more than one packet per window being dropped. This could
have a devastating effect upon the throughput of TCP over an
LFN. In addition, if a congestion control mechanism based
upon some form of random dropping were introduced into
gateways, randomly spaced packet drops would become common,
possible increasing the probability of dropping more than one
packet per window.
To generalize the Fast Retransmit/Fast Recovery mechanism to
handle multiple packets dropped per window, selective
acknowledgments are required. Unlike the normal cumulative
acknowledgments of TCP, selective acknowledgments give the
sender a complete picture of which segments are queued at the
receiver and which have not yet arrived. Some evidence in
favor of selective acknowledgments has been published
[NBS85], and selective acknowledgments have been included in
a number of experimental Internet protocols -- VMTP
[Cheriton88], NETBLT [Clark87], and RDP [Velten84], and
proposed for OSI TP4 [NBS85]. However, in the non-LFN
regime, selective acknowledgments reduce the number of
Jacobson, Braden, & Borman [Page 3]
RFC 1323 TCP Extensions for High Performance May 1992
packets retransmitted but do not otherwise improve
performance, making their complexity of questionable value.
However, selective acknowledgments are expected to become
much more important in the LFN regime.
RFC-1072 defined a new TCP "SACK" option to send a selective
acknowledgment. However, there are important technical
issues to be worked out concerning both the format and
semantics of the SACK option. Therefore, SACK has been
omitted from this package of extensions. It is hoped that
SACK can "catch up" during the standardization process.
(3) Round-Trip Measurement
TCP implements reliable data delivery by retransmitting
segments that are not acknowledged within some retransmission
timeout (RTO) interval. Accurate dynamic determination of an
appropriate RTO is essential to TCP performance. RTO is
determined by estimating the mean and variance of the
measured round-trip time (RTT), i.e., the time interval
between sending a segment and receiving an acknowledgment for
it [Jacobson88a].
Section 4 introduces a new TCP option, "Timestamps", and then
defines a mechanism using this option that allows nearly
every segment, including retransmissions, to be timed at
negligible computational cost. We use the mnemonic RTTM
(Round Trip Time Measurement) for this mechanism, to
distinguish it from other uses of the Timestamps option.
1.2 TCP Reliability
Now we turn from performance to reliability. High transfer rate
enters TCP performance through the bandwidth*delay product.
However, high transfer rate alone can threaten TCP reliability by
violating the assumptions behind the TCP mechanism for duplicate
detection and sequencing.
An especially serious kind of error may result from an accidental
reuse of TCP sequence numbers in data segments. Suppose that an
"old duplicate segment", e.g., a duplicate data segment that was
delayed in Internet queues, is delivered to the receiver at the
wrong moment, so that its sequence numbers falls somewhere within
the current window. There would be no checksum failure to warn of
the error, and the result could be an undetected corruption of the
data. Reception of an old duplicate ACK segment at the
transmitter could be only slightly less serious: it is likely to
Jacobson, Braden, & Borman [Page 4]
RFC 1323 TCP Extensions for High Performance May 1992
lock up the connection so that no further progress can be made,
forcing an RST on the connection.
TCP reliability depends upon the existence of a bound on the
lifetime of a segment: the "Maximum Segment Lifetime" or MSL. An
MSL is generally required by any reliable transport protocol,
since every sequence number field must be finite, and therefore
any sequence number may eventually be reused. In the Internet
protocol suite, the MSL bound is enforced by an IP-layer
mechanism, the "Time-to-Live" or TTL field.
Duplication of sequence numbers might happen in either of two
ways:
(1) Sequence number wrap-around on the current connection
A TCP sequence number contains 32 bits. At a high enough
transfer rate, the 32-bit sequence space may be "wrapped"
(cycled) within the time that a segment is delayed in queues.
(2) Earlier incarnation of the connection
Suppose that a connection terminates, either by a proper
close sequence or due to a host crash, and the same
connection (i.e., using the same pair of sockets) is
immediately reopened. A delayed segment from the terminated
connection could fall within the current window for the new
incarnation and be accepted as valid.
Duplicates from earlier incarnations, Case (2), are avoided by
enforcing the current fixed MSL of the TCP spec, as explained in
Section 5.3 and Appendix B. However, case (1), avoiding the
reuse of sequence numbers within the same connection, requires an
MSL bound that depends upon the transfer rate, and at high enough
rates, a new mechanism is required.
More specifically, if the maximum effective bandwidth at which TCP
is able to transmit over a particular path is B bytes per second,
then the following constraint must be satisfied for error-free
operation:
2**31 / B > MSL (secs) [1]
The following table shows the value for Twrap = 2**31/B in
seconds, for some important values of the bandwidth B:
Jacobson, Braden, & Borman [Page 5]
RFC 1323 TCP Extensions for High Performance May 1992
Network B*8 B Twrap
bits/sec bytes/sec secs
_______ _______ ______ ______
ARPANET 56kbps 7KBps 3*10**5 (~3.6 days)
DS1 1.5Mbps 190KBps 10**4 (~3 hours)
Ethernet 10Mbps 1.25MBps 1700 (~30 mins)
DS3 45Mbps 5.6MBps 380
FDDI 100Mbps 12.5MBps 170
Gigabit 1Gbps 125MBps 17
It is clear that wrap-around of the sequence space is not a
problem for 56kbps packet switching or even 10Mbps Ethernets. On
the other hand, at DS3 and FDDI speeds, Twrap is comparable to the
2 minute MSL assumed by the TCP specification [Postel81]. Moving
towards gigabit speeds, Twrap becomes too small for reliable
enforcement by the Internet TTL mechanism.
The 16-bit window field of TCP limits the effective bandwidth B to
2**16/RTT, where RTT is the round-trip time in seconds
[McKenzie89]. If the RTT is large enough, this limits B to a
value that meets the constraint [1] for a large MSL value. For
example, consider a transcontinental backbone with an RTT of 60ms
(set by the laws of physics). With the bandwidth*delay product
limited to 64KB by the TCP window size, B is then limited to
1.1MBps, no matter how high the theoretical transfer rate of the
path. This corresponds to cycling the sequence number space in
Twrap= 2000 secs, which is safe in today's Internet.
It is important to understand that the culprit is not the larger
window but rather the high bandwidth. For example, consider a
(very large) FDDI LAN with a diameter of 10km. Using the speed of
light, we can compute the RTT across the ring as
(2*10**4)/(3*10**8) = 67 microseconds, and the delay*bandwidth
product is then 833 bytes. A TCP connection across this LAN using
a window of only 833 bytes will run at the full 100mbps and can
wrap the sequence space in about 3 minutes, very close to the MSL
of TCP. Thus, high speed alone can cause a reliability problem
with sequence number wrap-around, even without extended windows.
Watson's Delta-T protocol [Watson81] includes network-layer
mechanisms for precise enforcement of an MSL. In contrast, the IP
Jacobson, Braden, & Borman [Page 6]
RFC 1323 TCP Extensions for High Performance May 1992
mechanism for MSL enforcement is loosely defined and even more
loosely implemented in the Internet. Therefore, it is unwise to
depend upon active enforcement of MSL for TCP connections, and it
is unrealistic to imagine setting MSL's smaller than the current
values (e.g., 120 seconds specified for TCP).
A possible fix for the problem of cycling the sequence space would
be to increase the size of the TCP sequence number field. For
example, the sequence number field (and also the acknowledgment
field) could be expanded to 64 bits. This could be done either by
changing the TCP header or by means of an additional option.
Section 5 presents a different mechanism, which we call PAWS
(Protect Against Wrapped Sequence numbers), to extend TCP
reliability to transfer rates well beyond the foreseeable upper
limit of network bandwidths. PAWS uses the TCP Timestamps option
defined in Section 4 to protect against old duplicates from the
same connection.
1.3 Using TCP options
The extensions defined in this memo all use new TCP options. We
must address two possible issues concerning the use of TCP
options: (1) compatibility and (2) overhead.
We must pay careful attention to compatibility, i.e., to
interoperation with existing implementations. The only TCP option
defined previously, MSS, may appear only on a SYN segment. Every
implementation should (and we expect that most will) ignore
unknown options on SYN segments. However, some buggy TCP
implementation might be crashed by the first appearance of an
option on a non-SYN segment. Therefore, for each of the
extensions defined below, TCP options will be sent on non-SYN
segments only when an exchange of options on the SYN segments has
indicated that both sides understand the extension. Furthermore,
an extension option will be sent in a segment only if
the corresponding option was received in the initial
segment.
A question may be raised about the bandwidth and processing
overhead for TCP options. Those options that occur on SYN
segments are not likely to cause a performance concern. Opening a
TCP connection requires execution of significant special-case
code, and the processing of options is unlikely to increase that
cost significantly.
On the other hand, a Timestamps option may appear in any data or
ACK segment, adding 12 bytes to the 20-byte TCP header. We
Jacobson, Braden, & Borman [Page 7]
RFC 1323 TCP Extensions for High Performance May 1992
believe that the bandwidth saved by reducing unnecessary
retransmissions will more than pay for the extra header bandwidth.
There is also an issue about the processing overhead for parsing
the variable byte-aligned format of options, particularly with a
RISC-architecture CPU. To meet this concern, Appendix A contains
a recommended layout of the options in TCP headers to achieve
reasonable data field alignment. In the spirit of Header
Prediction, a TCP can quickly test for this layout and if it is
verified then use a fast path. Hosts that use this canonical
layout will effectively use the options as a set of fixed-format
fields appended to the TCP header. However, to retain the
philosophical and protocol framework of TCP options, a TCP must be
prepared to parse an arbitrary options field, albeit with less
efficiency.
Finally, we observe that most of the mechanisms defined in this
memo are important for LFN's and/or very high-speed networks. For
low-speed networks, it might be a performance optimization to NOT
use these mechanisms. A TCP vendor concerned about optimal
performance over low-speed paths might consider turning these
extensions off for low-speed paths, or allow a user or
installation manager to disable them.
2. TCP WINDOW SCALE OPTION
2.1 Introduction
The window scale extension expands the definition of the TCP
window to 32 bits and then uses a scale factor to carry this 32-
bit value in the 16-bit Window field of the TCP header (SEG.WND in
RFC-793). The scale factor is carried in a new TCP option, Window
Scale. This option is sent only in a SYN segment (a segment with
the SYN bit on), hence the window scale is fixed in each direction
when a connection is opened. (Another design choice would be to
specify the window scale in every TCP segment. It would be
incorrect to send a window scale option only when the scale factor
changed, since a TCP option in an acknowledgement segment will not
be delivered reliably (unless the ACK happens to be piggy-backed
on data in the other direction). Fixing the scale when the
connection is opened has the advantage of lower overhead but the
disadvantage that the scale factor cannot be changed during the
connection.)
The maximum receive window, and therefore the scale factor, is
determined by the maximum receive buffer space. In a typical
modern implementation, this maximum buffer space is set by default
Jacobson, Braden, & Borman [Page 8]
RFC 1323 TCP Extensions for High Performance May 1992
but can be overridden by a user program before a TCP connection is
opened. This determines the scale factor, and therefore no new
user interface is needed for window scaling.
2.2 Window Scale Option
The three-byte Window Scale option may be sent in a SYN segment by
a TCP. It has two purposes: (1) indicate that the TCP is prepared
to do both send and receive window scaling, and (2) communicate a
scale factor to be applied to its receive window. Thus, a TCP
that is prepared to scale windows should send the option, even if
its own scale factor is 1. The scale factor is limited to a power
of two and encoded logarithmically, so it may be implemented by
binary shift operations.
TCP Window Scale Option (WSopt):
Kind: 3 Length: 3 bytes
+---------+---------+---------+
| Kind=3 |Length=3 |shift.cnt|
+---------+---------+---------+
This option is an offer, not a promise; both sides must send
Window Scale options in their SYN segments to enable window
scaling in either direction. If window scaling is enabled,
then the TCP that sent this option will right-shift its true
receive-window values by 'shift.cnt' bits for transmission in
SEG.WND. The value 'shift.cnt' may be zero (offering to scale,
while applying a scale factor of 1 to the receive window).
This option may be sent in an initial segment (i.e., a
segment with the SYN bit on and the ACK bit off). It may also
be sent in a segment, but only if a Window Scale op-
tion was received in the initial segment. A Window Scale
option in a segment without a SYN bit should be ignored.
The Window field in a SYN (i.e., a or ) segment
itself is never scaled.
2.3 Using the Window Scale Option
A model implementation of window scaling is as follows, using the
notation of RFC-793 [Postel81]:
* All windows are treated as 32-bit quantities for storage in
Jacobson, Braden, & Borman [Page 9]
RFC 1323 TCP Extensions for High Performance May 1992
the connection control block and for local calculations.
This includes the send-window (SND.WND) and the receive-
window (RCV.WND) values, as well as the congestion window.
* The connection state is augmented by two window shift counts,
Snd.Wind.Scale and Rcv.Wind.Scale, to be applied to the
incoming and outgoing window fields, respectively.
* If a TCP receives a segment containing a Window Scale
option, it sends its own Window Scale option in the
segment.
* The Window Scale option is sent with shift.cnt = R, where R
is the value that the TCP would like to use for its receive
window.
* Upon receiving a SYN segment with a Window Scale option
containing shift.cnt = S, a TCP sets Snd.Wind.Scale to S and
sets Rcv.Wind.Scale to R; otherwise, it sets both
Snd.Wind.Scale and Rcv.Wind.Scale to zero.
* The window field (SEG.WND) in the header of every incoming
segment, with the exception of SYN segments, is left-shifted
by Snd.Wind.Scale bits before updating SND.WND:
SND.WND = SEG.WND << Snd.Wind.Scale
(assuming the other conditions of RFC793 are met, and using
the "C" notation "<<" for left-shift).
* The window field (SEG.WND) of every outgoing segment, with
the exception of SYN segments, is right-shifted by
Rcv.Wind.Scale bits:
SEG.WND = RCV.WND >> Rcv.Wind.Scale.
TCP determines if a data segment is "old" or "new" by testing
whether its sequence number is within 2**31 bytes of the left edge
of the window, and if it is not, discarding the data as "old". To
insure that new data is never mistakenly considered old and vice-
versa, the left edge of the sender's window has to be at most
2**31 away from the right edge of the receiver's window.
Similarly with the sender's right edge and receiver's left edge.
Since the right and left edges of either the sender's or
receiver's window differ by the window size, and since the sender
and receiver windows can be out of phase by at most the window
size, the above constraints imply that 2 * the max window size
Jacobson, Braden, & Borman [Page 10]
RFC 1323 TCP Extensions for High Performance May 1992
must be less than 2**31, or
max window < 2**30
Since the max window is 2**S (where S is the scaling shift count)
times at most 2**16 - 1 (the maximum unscaled window), the maximum
window is guaranteed to be < 2*30 if S <= 14. Thus, the shift
count must be limited to 14 (which allows windows of 2**30 = 1
Gbyte). If a Window Scale option is received with a shift.cnt
value exceeding 14, the TCP should log the error but use 14
instead of the specified value.
The scale factor applies only to the Window field as transmitted
in the TCP header; each TCP using extended windows will maintain
the window values locally as 32-bit numbers. For example, the
"congestion window" computed by Slow Start and Congestion
Avoidance is not affected by the scale factor, so window scaling
will not introduce quantization into the congestion window.
3. RTTM: ROUND-TRIP TIME MEASUREMENT
3.1 Introduction
Accurate and current RTT estimates are necessary to adapt to
changing traffic conditions and to avoid an instability known as
"congestion collapse" [Nagle84] in a busy network. However,
accurate measurement of RTT may be difficult both in theory and in
implementation.
Many TCP implementations base their RTT measurements upon a sample
of only one packet per window. While this yields an adequate
approximation to the RTT for small windows, it results in an
unacceptably poor RTT estimate for an LFN. If we look at RTT
estimation as a signal processing problem (which it is), a data
signal at some frequency, the packet rate, is being sampled at a
lower frequency, the window rate. This lower sampling frequency
violates Nyquist's criteria and may therefore introduce "aliasing"
artifacts into the estimated RTT [Hamming77].
A good RTT estimator with a conservative retransmission timeout
calculation can tolerate aliasing when the sampling frequency is
"close" to the data frequency. For example, with a window of 8
packets, the sample rate is 1/8 the data frequency -- less than an
order of magnitude different. However, when the window is tens or
hundreds of packets, the RTT estimator may be seriously in error,
resulting in spurious retransmissions.
If there are dropped packets, the problem becomes worse. Zhang
Jacobson, Braden, & Borman [Page 11]
RFC 1323 TCP Extensions for High Performance May 1992
[Zhang86], Jain [Jain86] and Karn [Karn87] have shown that it is
not possible to accumulate reliable RTT estimates if retransmitted
segments are included in the estimate. Since a full window of
data will have been transmitted prior to a retransmission, all of
the segments in that window will have to be ACKed before the next
RTT sample can be taken. This means at least an additional
window's worth of time between RTT measurements and, as the error
rate approaches one per window of data (e.g., 10**-6 errors per
bit for the Wideband satellite network), it becomes effectively
impossible to obtain a valid RTT measurement.
A solution to these problems, which actually simplifies the sender
substantially, is as follows: using TCP options, the sender places
a timestamp in each data segment, and the receiver reflects these
timestamps back in ACK segments. Then a single subtract gives the
sender an accurate RTT measurement for every ACK segment (which
will correspond to every other data segment, with a sensible
receiver). We call this the RTTM (Round-Trip Time Measurement)
mechanism.
It is vitally important to use the RTTM mechanism with big
windows; otherwise, the door is opened to some dangerous
instabilities due to aliasing. Furthermore, the option is
probably useful for all TCP's, since it simplifies the sender.
3.2 TCP Timestamps Option
TCP is a symmetric protocol, allowing data to be sent at any time
in either direction, and therefore timestamp echoing may occur in
either direction. For simplicity and symmetry, we specify that
timestamps always be sent and echoed in both directions. For
efficiency, we combine the timestamp and timestamp reply fields
into a single TCP Timestamps Option.
Jacobson, Braden, & Borman [Page 12]
RFC 1323 TCP Extensions for High Performance May 1992
TCP Timestamps Option (TSopt):
Kind: 8
Length: 10 bytes
+-------+-------+---------------------+---------------------+
|Kind=8 | 10 | TS Value (TSval) |TS Echo Reply (TSecr)|
+-------+-------+---------------------+---------------------+
1 1 4 4
The Timestamps option carries two four-byte timestamp fields.
The Timestamp Value field (TSval) contains the current value of
the timestamp clock of the TCP sending the option.
The Timestamp Echo Reply field (TSecr) is only valid if the ACK
bit is set in the TCP header; if it is valid, it echos a times-
tamp value that was sent by the remote TCP in the TSval field
of a Timestamps option. When TSecr is not valid, its value
must be zero. The TSecr value will generally be from the most
recent Timestamp option that was received; however, there are
exceptions that are explained below.
A TCP may send the Timestamps option (TSopt) in an initial
segment (i.e., segment containing a SYN bit and no ACK
bit), and may send a TSopt in other segments only if it re-
ceived a TSopt in the initial segment for the connection.
3.3 The RTTM Mechanism
The timestamp value to be sent in TSval is to be obtained from a
(virtual) clock that we call the "timestamp clock". Its values
must be at least approximately proportional to real time, in order
to measure actual RTT.
The following example illustrates a one-way data flow with
segments arriving in sequence without loss. Here A, B, C...
represent data blocks occupying successive blocks of sequence
numbers, and ACK(A),... represent the corresponding cumulative
acknowledgments. The two timestamp fields of the Timestamps
option are shown symbolically as . Each TSecr
field contains the value most recently received in a TSval field.
Jacobson, Braden, & Borman [Page 13]
RFC 1323 TCP Extensions for High Performance May 1992
TCP A TCP B
------>
<----
------>
<----
. . . . . . . . . . . . . . . . . . . . . .
------>
<----
(etc)
The dotted line marks a pause (60 time units long) in which A had
nothing to send. Note that this pause inflates the RTT which B
could infer from receiving TSecr=131 in data segment C. Thus, in
one-way data flows, RTTM in the reverse direction measures a value
that is inflated by gaps in sending data. However, the following
rule prevents a resulting inflation of the measured RTT:
A TSecr value received in a segment is used to update the
averaged RTT measurement only if the segment acknowledges
some new data, i.e., only if it advances the left edge of the
send window.
Since TCP B is not sending data, the data segment C does not
acknowledge any new data when it arrives at B. Thus, the inflated
RTTM measurement is not used to update B's RTTM measurement.
3.4 Which Timestamp to Echo
If more than one Timestamps option is received before a reply
segment is sent, the TCP must choose only one of the TSvals to
echo, ignoring the others. To minimize the state kept in the
receiver (i.e., the number of unprocessed TSvals), the receiver
should be required to retain at most one timestamp in the
connection control block.
Jacobson, Braden, & Borman [Page 14]
RFC 1323 TCP Extensions for High Performance May 1992
There are three situations to consider:
(A) Delayed ACKs.
Many TCP's acknowledge only every Kth segment out of a group
of segments arriving within a short time interval; this
policy is known generally as "delayed ACKs". The data-sender
TCP must measure the effective RTT, including the additional
time due to delayed ACKs, or else it will retransmit
unnecessarily. Thus, when delayed ACKs are in use, the
receiver should reply with the TSval field from the earliest
unacknowledged segment.
(B) A hole in the sequence space (segment(s) have been lost).
The sender will continue sending until the window is filled,
and the receiver may be generating ACKs as these out-of-order
segments arrive (e.g., to aid "fast retransmit").
The lost segment is probably a sign of congestion, and in
that situation the sender should be conservative about
retransmission. Furthermore, it is better to overestimate
than underestimate the RTT. An ACK for an out-of-order
segment should therefore contain the timestamp from the most
recent segment that advanced the window.
The same situation occurs if segments are re-ordered by the
network.
(C) A filled hole in the sequence space.
The segment that fills the hole represents the most recent
measurement of the network characteristics. On the other
hand, an RTT computed from an earlier segment would probably
include the sender's retransmit time-out, badly biasing the
sender's average RTT estimate. Thus, the timestamp from the
latest segment (which filled the hole) must be echoed.
An algorithm that covers all three cases is described in the
following rules for Timestamps option processing on a synchronized
connection:
(1) The connection state is augmented with two 32-bit slots:
TS.Recent holds a timestamp to be echoed in TSecr whenever a
segment is sent, and Last.ACK.sent holds the ACK field from
the last segment sent. Last.ACK.sent will equal RCV.NXT
except when ACKs have been delayed.
Jacobson, Braden, & Borman [Page 15]
RFC 1323 TCP Extensions for High Performance May 1992
(2) If Last.ACK.sent falls within the range of sequence numbers
of an incoming segment:
SEG.SEQ <= Last.ACK.sent < SEG.SEQ + SEG.LEN
then the TSval from the segment is copied to TS.Recent;
otherwise, the TSval is ignored.
(3) When a TSopt is sent, its TSecr field is set to the current
TS.Recent value.
The following examples illustrate these rules. Here A, B, C...
represent data segments occupying successive blocks of sequence
numbers, and ACK(A),... represent the corresponding
acknowledgment segments. Note that ACK(A) has the same sequence
number as B. We show only one direction of timestamp echoing, for
clarity.
o Packets arrive in sequence, and some of the ACKs are delayed.
By Case (A), the timestamp from the oldest unacknowledged
segment is echoed.
TS.Recent
------------------->
1
------------------->
1
------------------->
1
<----
(etc)
o Packets arrive out of order, and every packet is
acknowledged.
By Case (B), the timestamp from the last segment that
advanced the left window edge is echoed, until the missing
segment arrives; it is echoed according to Case (C). The
same sequence would occur if segments B and D were lost and
retransmitted..
Jacobson, Braden, & Borman [Page 16]
RFC 1323 TCP Extensions for High Performance May 1992
TS.Recent
------------------->
1
<----
1
------------------->
1
<----
1
------------------->
2
<----
2
------------------->
2
<----
2
------------------->
4
<----
(etc)
4. PAWS: PROTECT AGAINST WRAPPED SEQUENCE NUMBERS
4.1 Introduction
Section 4.2 describes a simple mechanism to reject old duplicate
segments that might corrupt an open TCP connection; we call this
mechanism PAWS (Protect Against Wrapped Sequence numbers). PAWS
operates within a single TCP connection, using state that is saved
in the connection control block. Section 4.3 and Appendix C
discuss the implications of the PAWS mechanism for avoiding old
duplicates from previous incarnations of the same connection.
4.2 The PAWS Mechanism
PAWS uses the same TCP Timestamps option as the RTTM mechanism
described earlier, and assumes that every received TCP segment
(including data and ACK segments) contains a timestamp SEG.TSval
whose values are monotone non-decreasing in time. The basic idea
is that a segment can be discarded as an old duplicate if it is
received with a timestamp SEG.TSval less than some timestamp
recently received on this connection.
In both the PAWS and the RTTM mechanism, the "timestamps" are 32-
Jacobson, Braden, & Borman [Page 17]
RFC 1323 TCP Extensions for High Performance May 1992
bit unsigned integers in a modular 32-bit space. Thus, "less
than" is defined the same way it is for TCP sequence numbers, and
the same implementation techniques apply. If s and t are
timestamp values, s < t if 0 < (t - s) < 2**31, computed in
unsigned 32-bit arithmetic.
The choice of incoming timestamps to be saved for this comparison
must guarantee a value that is monotone increasing. For example,
we might save the timestamp from the segment that last advanced
the left edge of the receive window, i.e., the most recent in-
sequence segment. Instead, we choose the value TS.Recent
introduced in Section 3.4 for the RTTM mechanism, since using a
common value for both PAWS and RTTM simplifies the implementation
of both. As Section 3.4 explained, TS.Recent differs from the
timestamp from the last in-sequence segment only in the case of
delayed ACKs, and therefore by less than one window. Either
choice will therefore protect against sequence number wrap-around.
RTTM was specified in a symmetrical manner, so that TSval
timestamps are carried in both data and ACK segments and are
echoed in TSecr fields carried in returning ACK or data segments.
PAWS submits all incoming segments to the same test, and therefore
protects against duplicate ACK segments as well as data segments.
(An alternative un-symmetric algorithm would protect against old
duplicate ACKs: the sender of data would reject incoming ACK
segments whose TSecr values were less than the TSecr saved from
the last segment whose ACK field advanced the left edge of the
send window. This algorithm was deemed to lack economy of
mechanism and symmetry.)
TSval timestamps sent on {SYN} and {SYN,ACK} segments are used to
initialize PAWS. PAWS protects against old duplicate non-SYN
segments, and duplicate SYN segments received while there is a
synchronized connection. Duplicate {SYN} and {SYN,ACK} segments
received when there is no connection will be discarded by the
normal 3-way handshake and sequence number checks of TCP.
It is recommended that RST segments NOT carry timestamps, and that
RST segments be acceptable regardless of their timestamp. Old
duplicate RST segments should be exceedingly unlikely, and their
cleanup function should take precedence over timestamps.
4.2.1 Basic PAWS Algorithm
The PAWS algorithm requires the following processing to be
performed on all incoming segments for a synchronized
connection:
Jacobson, Braden, & Borman [Page 18]
RFC 1323 TCP Extensions for High Performance May 1992
R1) If there is a Timestamps option in the arriving segment
and SEG.TSval < TS.Recent and if TS.Recent is valid (see
later discussion), then treat the arriving segment as not
acceptable:
Send an acknowledgement in reply as specified in
RFC-793 page 69 and drop the segment.
Note: it is necessary to send an ACK segment in order
to retain TCP's mechanisms for detecting and
recovering from half-open connections. For example,
see Figure 10 of RFC-793.
R2) If the segment is outside the window, reject it (normal
TCP processing)
R3) If an arriving segment satisfies: SEG.SEQ <= Last.ACK.sent
(see Section 3.4), then record its timestamp in TS.Recent.
R4) If an arriving segment is in-sequence (i.e., at the left
window edge), then accept it normally.
R5) Otherwise, treat the segment as a normal in-window, out-
of-sequence TCP segment (e.g., queue it for later delivery
to the user).
Steps R2, R4, and R5 are the normal TCP processing steps
specified by RFC-793.
It is important to note that the timestamp is checked only when
a segment first arrives at the receiver, regardless of whether
it is in-sequence or it must be queued for later delivery.
Consider the following example.
Suppose the segment sequence: A.1, B.1, C.1, ..., Z.1 has
been sent, where the letter indicates the sequence number
and the digit represents the timestamp. Suppose also that
segment B.1 has been lost. The timestamp in TS.TStamp is
1 (from A.1), so C.1, ..., Z.1 are considered acceptable
and are queued. When B is retransmitted as segment B.2
(using the latest timestamp), it fills the hole and causes
all the segments through Z to be acknowledged and passed
to the user. The timestamps of the queued segments are
*not* inspected again at this time, since they have
already been accepted. When B.2 is accepted, TS.Stamp is
set to 2.
This rule allows reasonable performance under loss. A full
Jacobson, Braden, & Borman [Page 19]
RFC 1323 TCP Extensions for High Performance May 1992
window of data is in transit at all times, and after a loss a
full window less one packet will show up out-of-sequence to be
queued at the receiver (e.g., up to ~2**30 bytes of data); the
timestamp option must not result in discarding this data.
In certain unlikely circumstances, the algorithm of rules R1-R4
could lead to discarding some segments unnecessarily, as shown
in the following example:
Suppose again that segments: A.1, B.1, C.1, ..., Z.1 have
been sent in sequence and that segment B.1 has been lost.
Furthermore, suppose delivery of some of C.1, ... Z.1 is
delayed until AFTER the retransmission B.2 arrives at the
receiver. These delayed segments will be discarded
unnecessarily when they do arrive, since their timestamps
are now out of date.
This case is very unlikely to occur. If the retransmission was
triggered by a timeout, some of the segments C.1, ... Z.1 must
have been delayed longer than the RTO time. This is presumably
an unlikely event, or there would be many spurious timeouts and
retransmissions. If B's retransmission was triggered by the
"fast retransmit" algorithm, i.e., by duplicate ACKs, then the
queued segments that caused these ACKs must have been received
already.
Even if a segment were delayed past the RTO, the Fast
Retransmit mechanism [Jacobson90c] will cause the delayed
packets to be retransmitted at the same time as B.2, avoiding
an extra RTT and therefore causing a very small performance
penalty.
We know of no case with a significant probability of occurrence
in which timestamps will cause performance degradation by
unnecessarily discarding segments.
4.2.2 Timestamp Clock
It is important to understand that the PAWS algorithm does not
require clock synchronization between sender and receiver. The
sender's timestamp clock is used to stamp the segments, and the
sender uses the echoed timestamp to measure RTT's. However,
the receiver treats the timestamp as simply a monotone-
increasing serial number, without any necessary connection to
its clock. From the receiver's viewpoint, the timestamp is
acting as a logical extension of the high-order bits of the
sequence number.
Jacobson, Braden, & Borman [Page 20]
RFC 1323 TCP Extensions for High Performance May 1992
The receiver algorithm does place some requirements on the
frequency of the timestamp clock.
(a) The timestamp clock must not be "too slow".
It must tick at least once for each 2**31 bytes sent. In
fact, in order to be useful to the sender for round trip
timing, the clock should tick at least once per window's
worth of data, and even with the RFC-1072 window
extension, 2**31 bytes must be at least two windows.
To make this more quantitative, any clock faster than 1
tick/sec will reject old duplicate segments for link
speeds of ~8 Gbps. A 1ms timestamp clock will work at
link speeds up to 8 Tbps (8*10**12) bps!
(b) The timestamp clock must not be "too fast".
Its recycling time must be greater than MSL seconds.
Since the clock (timestamp) is 32 bits and the worst-case
MSL is 255 seconds, the maximum acceptable clock frequency
is one tick every 59 ns.
However, it is desirable to establish a much longer
recycle period, in order to handle outdated timestamps on
idle connections (see Section 4.2.3), and to relax the MSL
requirement for preventing sequence number wrap-around.
With a 1 ms timestamp clock, the 32-bit timestamp will
wrap its sign bit in 24.8 days. Thus, it will reject old
duplicates on the same connection if MSL is 24.8 days or
less. This appears to be a very safe figure; an MSL of
24.8 days or longer can probably be assumed by the gateway
system without requiring precise MSL enforcement by the
TTL value in the IP layer.
Based upon these considerations, we choose a timestamp clock
frequency in the range 1 ms to 1 sec per tick. This range also
matches the requirements of the RTTM mechanism, which does not
need much more resolution than the granularity of the
retransmit timer, e.g., tens or hundreds of milliseconds.
The PAWS mechanism also puts a strong monotonicity requirement
on the sender's timestamp clock. The method of implementation
of the timestamp clock to meet this requirement depends upon
the system hardware and software.
* Some hosts have a hardware clock that is guaranteed to be
monotonic between hardware resets.
Jacobson, Braden, & Borman [Page 21]
RFC 1323 TCP Extensions for High Performance May 1992
* A clock interrupt may be used to simply increment a binary
integer by 1 periodically.
* The timestamp clock may be derived from a system clock
that is subject to being abruptly changed, by adding a
variable offset value. This offset is initialized to
zero. When a new timestamp clock value is needed, the
offset can be adjusted as necessary to make the new value
equal to or larger than the previous value (which was
saved for this purpose).
4.2.3 Outdated Timestamps
If a connection remains idle long enough for the timestamp
clock of the other TCP to wrap its sign bit, then the value
saved in TS.Recent will become too old; as a result, the PAWS
mechanism will cause all subsequent segments to be rejected,
freezing the connection (until the timestamp clock wraps its
sign bit again).
With the chosen range of timestamp clock frequencies (1 sec to
1 ms), the time to wrap the sign bit will be between 24.8 days
and 24800 days. A TCP connection that is idle for more than 24
days and then comes to life is exceedingly unusual. However,
it is undesirable in principle to place any limitation on TCP
connection lifetimes.
We therefore require that an implementation of PAWS include a
mechanism to "invalidate" the TS.Recent value when a connection
is idle for more than 24 days. (An alternative solution to the
problem of outdated timestamps would be to send keepalive
segments at a very low rate, but still more often than the
wrap-around time for timestamps, e.g., once a day. This would
impose negligible overhead. However, the TCP specification has
never included keepalives, so the solution based upon
invalidation was chosen.)
Note that a TCP does not know the frequency, and therefore, the
wraparound time, of the other TCP, so it must assume the worst.
The validity of TS.Recent needs to be checked only if the basic
PAWS timestamp check fails, i.e., only if SEG.TSval <
TS.Recent. If TS.Recent is found to be invalid, then the
segment is accepted, regardless of the failure of the timestamp
check, and rule R3 updates TS.Recent with the TSval from the
new segment.
To detect how long the connection has been idle, the TCP may
Jacobson, Braden, & Borman [Page 22]
RFC 1323 TCP Extensions for High Performance May 1992
update a clock or timestamp value associated with the
connection whenever TS.Recent is updated, for example. The
details will be implementation-dependent.
4.2.4 Header Prediction
"Header prediction" [Jacobson90a] is a high-performance
transport protocol implementation technique that is most
important for high-speed links. This technique optimizes the
code for the most common case, receiving a segment correctly
and in order. Using header prediction, the receiver asks the
question, "Is this segment the next in sequence?" This
question can be answered in fewer machine instructions than the
question, "Is this segment within the window?"
Adding header prediction to our timestamp procedure leads to
the following recommended sequence for processing an arriving
TCP segment:
H1) Check timestamp (same as step R1 above)
H2) Do header prediction: if segment is next in sequence and
if there are no special conditions requiring additional
processing, accept the segment, record its timestamp, and
skip H3.
H3) Process the segment normally, as specified in RFC-793.
This includes dropping segments that are outside the win-
dow and possibly sending acknowledgments, and queueing
in-window, out-of-sequence segments.
Another possibility would be to interchange steps H1 and H2,
i.e., to perform the header prediction step H2 FIRST, and
perform H1 and H3 only when header prediction fails. This
could be a performance improvement, since the timestamp check
in step H1 is very unlikely to fail, and it requires interval
arithmetic on a finite field, a relatively expensive operation.
To perform this check on every single segment is contrary to
the philosophy of header prediction. We believe that this
change might reduce CPU time for TCP protocol processing by up
to 5-10% on high-speed networks.
However, putting H2 first would create a hazard: a segment from
2**32 bytes in the past might arrive at exactly the wrong time
and be accepted mistakenly by the header-prediction step. The
following reasoning has been introduced [Jacobson90b] to show
that the probability of this failure is negligible.
Jacobson, Braden, & Borman [Page 23]
RFC 1323 TCP Extensions for High Performance May 1992
If all segments are equally likely to show up as old
duplicates, then the probability of an old duplicate
exactly matching the left window edge is the maximum
segment size (MSS) divided by the size of the sequence
space. This ratio must be less than 2**-16, since MSS
must be < 2**16; for example, it will be (2**12)/(2**32) =
2**-20 for an FDDI link. However, the older a segment is,
the less likely it is to be retained in the Internet, and
under any reasonable model of segment lifetime the
probability of an old duplicate exactly at the left window
edge must be much smaller than 2**-16.
The 16 bit TCP checksum also allows a basic unreliability
of one part in 2**16. A protocol mechanism whose
reliability exceeds the reliability of the TCP checksum
should be considered "good enough", i.e., it won't
contribute significantly to the overall error rate. We
therefore believe we can ignore the problem of an old
duplicate being accepted by doing header prediction before
checking the timestamp.
However, this probabilistic argument is not universally
accepted, and the consensus at present is that the performance
gain does not justify the hazard in the general case. It is
therefore recommended that H2 follow H1.
4.3. Duplicates from Earlier Incarnations of Connection
The PAWS mechanism protects against errors due to sequence number
wrap-around on high-speed connection. Segments from an earlier
incarnation of the same connection are also a potential cause of
old duplicate errors. In both cases, the TCP mechanisms to
prevent such errors depend upon the enforcement of a maximum
segment lifetime (MSL) by the Internet (IP) layer (see Appendix of
RFC-1185 for a detailed discussion). Unlike the case of sequence
space wrap-around, the MSL required to prevent old duplicate
errors from earlier incarnations does not depend upon the transfer
rate. If the IP layer enforces the recommended 2 minute MSL of
TCP, and if the TCP rules are followed, TCP connections will be
safe from earlier incarnations, no matter how high the network
speed. Thus, the PAWS mechanism is not required for this case.
We may still ask whether the PAWS mechanism can provide additional
security against old duplicates from earlier connections, allowing
us to relax the enforcement of MSL by the IP layer. Appendix B
explores this question, showing that further assumptions and/or
mechanisms are required, beyond those of PAWS. This is not part
of the current extension.
Jacobson, Braden, & Borman [Page 24]
RFC 1323 TCP Extensions for High Performance May 1992
5. CONCLUSIONS AND ACKNOWLEDGMENTS
This memo presented a set of extensions to TCP to provide efficient
operation over large-bandwidth*delay-product paths and reliable
operation over very high-speed paths. These extensions are designed
to provide compatible interworking with TCP's that do not implement
the extensions.
These mechanisms are implemented using new TCP options for scaled
windows and timestamps. The timestamps are used for two distinct
mechanisms: RTTM (Round Trip Time Measurement) and PAWS (Protect
Against Wrapped Sequences).
The Window Scale option was originally suggested by Mike St. Johns of
USAF/DCA. The present form of the option was suggested by Mike
Karels of UC Berkeley in response to a more cumbersome scheme defined
by Van Jacobson. Lixia Zhang helped formulate the PAWS mechanism
description in RFC-1185.
Finally, much of this work originated as the result of discussions
within the End-to-End Task Force on the theoretical limitations of
transport protocols in general and TCP in particular. More recently,
task force members and other on the end2end-interest list have made
valuable contributions by pointing out flaws in the algorithms and
the documentation. The authors are grateful for all these
contributions.
6. REFERENCES
[Clark87] Clark, D., Lambert, M., and L. Zhang, "NETBLT: A Bulk
Data Transfer Protocol", RFC 998, MIT, March 1987.
[Garlick77] Garlick, L., R. Rom, and J. Postel, "Issues in
Reliable Host-to-Host Protocols", Proc. Second Berkeley Workshop
on Distributed Data Management and Computer Networks, May 1977.
[Hamming77] Hamming, R., "Digital Filters", ISBN 0-13-212571-4,
Prentice Hall, Englewood Cliffs, N.J., 1977.
[Cheriton88] Cheriton, D., "VMTP: Versatile Message Transaction
Protocol", RFC 1045, Stanford University, February 1988.
[Jacobson88a] Jacobson, V., "Congestion Avoidance and Control",
SIGCOMM '88, Stanford, CA., August 1988.
[Jacobson88b] Jacobson, V., and R. Braden, "TCP Extensions for
Long-Delay Paths", RFC-1072, LBL and USC/Information Sciences
Institute, October 1988.
Jacobson, Braden, & Borman [Page 25]
RFC 1323 TCP Extensions for High Performance May 1992
[Jacobson90a] Jacobson, V., "4BSD Header Prediction", ACM
Computer Communication Review, April 1990.
[Jacobson90b] Jacobson, V., Braden, R., and Zhang, L., "TCP
Extension for High-Speed Paths", RFC-1185, LBL and USC/Information
Sciences Institute, October 1990.
[Jacobson90c] Jacobson, V., "Modified TCP congestion avoidance
algorithm", Message to end2end-interest mailing list, April 1990.
[Jain86] Jain, R., "Divergence of Timeout Algorithms for Packet
Retransmissions", Proc. Fifth Phoenix Conf. on Comp. and Comm.,
Scottsdale, Arizona, March 1986.
[Karn87] Karn, P. and C. Partridge, "Estimating Round-Trip Times
in Reliable Transport Protocols", Proc. SIGCOMM '87, Stowe, VT,
August 1987.
[McKenzie89] McKenzie, A., "A Problem with the TCP Big Window
Option", RFC 1110, BBN STC, August 1989.
[Nagle84] Nagle, J., "Congestion Control in IP/TCP
Internetworks", RFC 896, FACC, January 1984.
[NBS85] Colella, R., Aronoff, R., and K. Mills, "Performance
Improvements for ISO Transport", Ninth Data Comm Symposium,
published in ACM SIGCOMM Comp Comm Review, vol. 15, no. 5,
September 1985.
[Postel81] Postel, J., "Transmission Control Protocol - DARPA
Internet Program Protocol Specification", RFC 793, DARPA,
September 1981.
[Velten84] Velten, D., Hinden, R., and J. Sax, "Reliable Data
Protocol", RFC 908, BBN, July 1984.
[Watson81] Watson, R., "Timer-based Mechanisms in Reliable
Transport Protocol Connection Management", Computer Networks, Vol.
5, 1981.
[Zhang86] Zhang, L., "Why TCP Timers Don't Work Well", Proc.
SIGCOMM '86, Stowe, Vt., August 1986.
Jacobson, Braden, & Borman [Page 26]
RFC 1323 TCP Extensions for High Performance May 1992
APPENDIX A: IMPLEMENTATION SUGGESTIONS
The following layouts are recommended for sending options on non-SYN
segments, to achieve maximum feasible alignment of 32-bit and 64-bit
machines.
+--------+--------+--------+--------+
| NOP | NOP | TSopt | 10 |
+--------+--------+--------+--------+
| TSval timestamp |
+--------+--------+--------+--------+
| TSecr timestamp |
+--------+--------+--------+--------+
APPENDIX B: DUPLICATES FROM EARLIER CONNECTION INCARNATIONS
There are two cases to be considered: (1) a system crashing (and
losing connection state) and restarting, and (2) the same connection
being closed and reopened without a loss of host state. These will
be described in the following two sections.
B.1 System Crash with Loss of State
TCP's quiet time of one MSL upon system startup handles the loss
of connection state in a system crash/restart. For an
explanation, see for example "When to Keep Quiet" in the TCP
protocol specification [Postel81]. The MSL that is required here
does not depend upon the transfer speed. The current TCP MSL of 2
minutes seems acceptable as an operational compromise, as many
host systems take this long to boot after a crash.
However, the timestamp option may be used to ease the MSL
requirements (or to provide additional security against data
corruption). If timestamps are being used and if the timestamp
clock can be guaranteed to be monotonic over a system
crash/restart, i.e., if the first value of the sender's timestamp
clock after a crash/restart can be guaranteed to be greater than
the last value before the restart, then a quiet time will be
unnecessary.
To dispense totally with the quiet time would require that the
host clock be synchronized to a time source that is stable over
the crash/restart period, with an accuracy of one timestamp clock
tick or better. We can back off from this strict requirement to
take advantage of approximate clock synchronization. Suppose that
the clock is always re-synchronized to within N timestamp clock
Jacobson, Braden, & Borman [Page 27]
RFC 1323 TCP Extensions for High Performance May 1992
ticks and that booting (extended with a quiet time, if necessary)
takes more than N ticks. This will guarantee monotonicity of the
timestamps, which can then be used to reject old duplicates even
without an enforced MSL.
B.2 Closing and Reopening a Connection
When a TCP connection is closed, a delay of 2*MSL in TIME-WAIT
state ties up the socket pair for 4 minutes (see Section 3.5 of
[Postel81]. Applications built upon TCP that close one connection
and open a new one (e.g., an FTP data transfer connection using
Stream mode) must choose a new socket pair each time. The TIME-
WAIT delay serves two different purposes:
(a) Implement the full-duplex reliable close handshake of TCP.
The proper time to delay the final close step is not really
related to the MSL; it depends instead upon the RTO for the
FIN segments and therefore upon the RTT of the path. (It
could be argued that the side that is sending a FIN knows
what degree of reliability it needs, and therefore it should
be able to determine the length of the TIME-WAIT delay for
the FIN's recipient. This could be accomplished with an
appropriate TCP option in FIN segments.)
Although there is no formal upper-bound on RTT, common
network engineering practice makes an RTT greater than 1
minute very unlikely. Thus, the 4 minute delay in TIME-WAIT
state works satisfactorily to provide a reliable full-duplex
TCP close. Note again that this is independent of MSL
enforcement and network speed.
The TIME-WAIT state could cause an indirect performance
problem if an application needed to repeatedly close one
connection and open another at a very high frequency, since
the number of available TCP ports on a host is less than
2**16. However, high network speeds are not the major
contributor to this problem; the RTT is the limiting factor
in how quickly connections can be opened and closed.
Therefore, this problem will be no worse at high transfer
speeds.
(b) Allow old duplicate segments to expire.
To replace this function of TIME-WAIT state, a mechanism
would have to operate across connections. PAWS is defined
strictly within a single connection; the last timestamp is
TS.Recent is kept in the connection control block, and
Jacobson, Braden, & Borman [Page 28]
RFC 1323 TCP Extensions for High Performance May 1992
discarded when a connection is closed.
An additional mechanism could be added to the TCP, a per-host
cache of the last timestamp received from any connection.
This value could then be used in the PAWS mechanism to reject
old duplicate segments from earlier incarnations of the
connection, if the timestamp clock can be guaranteed to have
ticked at least once since the old connection was open. This
would require that the TIME-WAIT delay plus the RTT together
must be at least one tick of the sender's timestamp clock.
Such an extension is not part of the proposal of this RFC.
Note that this is a variant on the mechanism proposed by
Garlick, Rom, and Postel [Garlick77], which required each
host to maintain connection records containing the highest
sequence numbers on every connection. Using timestamps
instead, it is only necessary to keep one quantity per remote
host, regardless of the number of simultaneous connections to
that host.
Jacobson, Braden, & Borman [Page 29]
RFC 1323 TCP Extensions for High Performance May 1992
APPENDIX C: CHANGES FROM RFC-1072, RFC-1185
The protocol extensions defined in this document differ in several
important ways from those defined in RFC-1072 and RFC-1185.
(a) SACK has been deferred to a later memo.
(b) The detailed rules for sending timestamp replies (see Section
3.4) differ in important ways. The earlier rules could result
in an under-estimate of the RTT in certain cases (packets
dropped or out of order).
(c) The same value TS.Recent is now shared by the two distinct
mechanisms RTTM and PAWS. This simplification became possible
because of change (b).
(d) An ambiguity in RFC-1185 was resolved in favor of putting
timestamps on ACK as well as data segments. This supports the
symmetry of the underlying TCP protocol.
(e) The echo and echo reply options of RFC-1072 were combined into a
single Timestamps option, to reflect the symmetry and to
simplify processing.
(f) The problem of outdated timestamps on long-idle connections,
discussed in Section 4.2.2, was realized and resolved.
(g) RFC-1185 recommended that header prediction take precedence over
the timestamp check. Based upon some scepticism about the
probabilistic arguments given in Section 4.2.4, it was decided
to recommend that the timestamp check be performed first.
(h) The spec was modified so that the extended options will be sent
on segments only when they are received in the
corresponding segments. This provides the most
conservative possible conditions for interoperation with
implementations without the extensions.
In addition to these substantive changes, the present RFC attempts to
specify the algorithms unambiguously by presenting modifications to
the Event Processing rules of RFC-793; see Appendix E.
Jacobson, Braden, & Borman [Page 30]
RFC 1323 TCP Extensions for High Performance May 1992
APPENDIX D: SUMMARY OF NOTATION
The following notation has been used in this document.
Options
WSopt: TCP Window Scale Option
TSopt: TCP Timestamps Option
Option Fields
shift.cnt: Window scale byte in WSopt.
TSval: 32-bit Timestamp Value field in TSopt.
TSecr: 32-bit Timestamp Reply field in TSopt.
Option Fields in Current Segment
SEG.TSval: TSval field from TSopt in current segment.
SEG.TSecr: TSecr field from TSopt in current segment.
SEG.WSopt: 8-bit value in WSopt
Clock Values
my.TSclock: Local source of 32-bit timestamp values
my.TSclock.rate: Period of my.TSclock (1 ms to 1 sec).
Per-Connection State Variables
TS.Recent: Latest received Timestamp
Last.ACK.sent: Last ACK field sent
Snd.TS.OK: 1-bit flag
Snd.WS.OK: 1-bit flag
Rcv.Wind.Scale: Receive window scale power
Snd.Wind.Scale: Send window scale power
Jacobson, Braden, & Borman [Page 31]
RFC 1323 TCP Extensions for High Performance May 1992
APPENDIX E: EVENT PROCESSING
Event Processing
OPEN Call
...
An initial send sequence number (ISS) is selected. Send a SYN
segment of the form:
...
SEND Call
CLOSED STATE (i.e., TCB does not exist)
...
LISTEN STATE
If the foreign socket is specified, then change the connection
from passive to active, select an ISS. Send a SYN segment
containing the options: and
. Set SND.UNA to ISS, SND.NXT to ISS+1.
Enter SYN-SENT state. ...
SYN-SENT STATE
SYN-RECEIVED STATE
...
ESTABLISHED STATE
CLOSE-WAIT STATE
Segmentize the buffer and send it with a piggybacked
acknowledgment (acknowledgment value = RCV.NXT). ...
If the urgent flag is set ...
If the Snd.TS.OK flag is set, then include the TCP Timestamps
option in each data segment.
Scale the receive window for transmission in the segment header:
SEG.WND = (SND.WND >> Rcv.Wind.Scale).
Jacobson, Braden, & Borman [Page 32]
RFC 1323 TCP Extensions for High Performance May 1992
SEGMENT ARRIVES
...
If the state is LISTEN then
first check for an RST
...
second check for an ACK
...
third check for a SYN
if the SYN bit is set, check the security. If the ...
...
If the SEG.PRC is less than the TCB.PRC then continue.
Check for a Window Scale option (WSopt); if one is found, save
SEG.WSopt in Snd.Wind.Scale and set Snd.WS.OK flag on.
Otherwise, set both Snd.Wind.Scale and Rcv.Wind.Scale to zero
and clear Snd.WS.OK flag.
Check for a TSopt option; if one is found, save SEG.TSval in the
variable TS.Recent and turn on the Snd.TS.OK bit.
Set RCV.NXT to SEG.SEQ+1, IRS is set to SEG.SEQ and any other
control or text should be queued for processing later. ISS
should be selected and a SYN segment sent of the form:
If the Snd.WS.OK bit is on, include a WSopt option
in this segment. If the Snd.TS.OK bit is
on, include a TSopt in this
segment. Last.ACK.sent is set to RCV.NXT.
SND.NXT is set to ISS+1 and SND.UNA to ISS. The connection
state should be changed to SYN-RECEIVED. Note that any other
incoming control or data (combined with SYN) will be processed
in the SYN-RECEIVED state, but processing of SYN and ACK should
not be repeated. If the listen was not fully specified (i.e.,
the foreign socket was not fully specified), then the
unspecified fields should be filled in now.
Jacobson, Braden, & Borman [Page 33]
RFC 1323 TCP Extensions for High Performance May 1992
fourth other text or control
...
If the state is SYN-SENT then
first check the ACK bit
...
fourth check the SYN bit
...
If the SYN bit is on and the security/compartment and precedence
are acceptable then, RCV.NXT is set to SEG.SEQ+1, IRS is set to
SEG.SEQ, and any acknowledgements on the retransmission queue
which are thereby acknowledged should be removed.
Check for a Window Scale option (WSopt); if is found, save
SEG.WSopt in Snd.Wind.Scale; otherwise, set both Snd.Wind.Scale
and Rcv.Wind.Scale to zero.
Check for a TSopt option; if one is found, save SEG.TSval in
variable TS.Recent and turn on the Snd.TS.OK bit in the
connection control block. If the ACK bit is set, use my.TSclock
- SEG.TSecr as the initial RTT estimate.
If SND.UNA > ISS (our SYN has been ACKed), change the connection
state to ESTABLISHED, form an ACK segment:
and send it. If the Snd.Echo.OK bit is on, include a TSopt
option in this ACK segment.
Last.ACK.sent is set to RCV.NXT.
Data or controls which were queued for transmission may be
included. If there are other controls or text in the segment
then continue processing at the sixth step below where the URG
bit is checked, otherwise return.
Otherwise enter SYN-RECEIVED, form a SYN,ACK segment:
and send it. If the Snd.Echo.OK bit is on, include a TSopt
option in this segment. If
Jacobson, Braden, & Borman [Page 34]
RFC 1323 TCP Extensions for High Performance May 1992
the Snd.WS.OK bit is on, include a WSopt option
in this segment. Last.ACK.sent is set to
RCV.NXT.
If there are other controls or text in the segment, queue them
for processing after the ESTABLISHED state has been reached,
return.
fifth, if neither of the SYN or RST bits is set then drop the
segment and return.
Otherwise,
First, check sequence number
SYN-RECEIVED STATE
ESTABLISHED STATE
FIN-WAIT-1 STATE
FIN-WAIT-2 STATE
CLOSE-WAIT STATE
CLOSING STATE
LAST-ACK STATE
TIME-WAIT STATE
Segments are processed in sequence. Initial tests on arrival
are used to discard old duplicates, but further processing is
done in SEG.SEQ order. If a segment's contents straddle the
boundary between old and new, only the new parts should be
processed.
Rescale the received window field:
TrueWindow = SEG.WND << Snd.Wind.Scale,
and use "TrueWindow" in place of SEG.WND in the following steps.
Check whether the segment contains a Timestamps option and bit
Snd.TS.OK is on. If so:
If SEG.TSval < TS.Recent, then test whether connection has
been idle less than 24 days; if both are true, then the
segment is not acceptable; follow steps below for an
unacceptable segment.
If SEG.SEQ is equal to Last.ACK.sent, then save SEG.ECopt in
variable TS.Recent.
Jacobson, Braden, & Borman [Page 35]
RFC 1323 TCP Extensions for High Performance May 1992
There are four cases for the acceptability test for an incoming
segment:
...
If an incoming segment is not acceptable, an acknowledgment
should be sent in reply (unless the RST bit is set, if so drop
the segment and return):
Last.ACK.sent is set to SEG.ACK of the acknowledgment. If the
Snd.Echo.OK bit is on, include the Timestamps option
in this ACK segment. Set
Last.ACK.sent to SEG.ACK and send the ACK segment. After
sending the acknowledgment, drop the unacceptable segment and
return.
...
fifth check the ACK field.
if the ACK bit is off drop the segment and return.
if the ACK bit is on
...
ESTABLISHED STATE
If SND.UNA < SEG.ACK =< SND.NXT then, set SND.UNA <- SEG.ACK.
Also compute a new estimate of round-trip time. If Snd.TS.OK
bit is on, use my.TSclock - SEG.TSecr; otherwise use the
elapsed time since the first segment in the retransmission
queue was sent. Any segments on the retransmission queue
which are thereby entirely acknowledged...
...
Seventh, process the segment text.
ESTABLISHED STATE
FIN-WAIT-1 STATE
FIN-WAIT-2 STATE
...
Send an acknowledgment of the form:
Jacobson, Braden, & Borman [Page 36]
RFC 1323 TCP Extensions for High Performance May 1992
If the Snd.TS.OK bit is on, include Timestamps option
in this ACK segment. Set
Last.ACK.sent to SEG.ACK of the acknowledgment, and send it.
This acknowledgment should be piggy-backed on a segment being
transmitted if possible without incurring undue delay.
...
Security Considerations
Security issues are not discussed in this memo.
Authors' Addresses
Van Jacobson
University of California
Lawrence Berkeley Laboratory
Mail Stop 46A
Berkeley, CA 94720
Phone: (415) 486-6411
EMail: van@CSAM.LBL.GOV
Bob Braden
University of Southern California
Information Sciences Institute
4676 Admiralty Way
Marina del Rey, CA 90292
Phone: (310) 822-1511
EMail: Braden@ISI.EDU
Dave Borman
Cray Research
655-E Lone Oak Drive
Eagan, MN 55121
Phone: (612) 683-5571
Email: dab@cray.com
Jacobson, Braden, & Borman [Page 37]