RFC 1812






Network Working Group                                   F. Baker, Editor
Request for Comments: 1812                                 Cisco Systems
Obsoletes: RFC 1716, 1009                                      June 1995
Category: Standards Track


                 Requirements for IP Version 4 Routers

Status of this Memo

   This document specifies an Internet standards track protocol for the
   Internet community, and requests discussion and suggestions for
   improvements.  Please refer to the current edition of the "Internet
   Official Protocol Standards" (STD 1) for the standardization state
   and status of this protocol.  Distribution of this memo is unlimited.

PREFACE

   This document is an updated version of RFC 1716, the historical
   Router Requirements document.  That RFC preserved the significant
   work that went into the working group, but failed to adequately
   describe current technology for the IESG to consider it a current
   standard.

   The current editor had been asked to bring the document up to date,
   so that it is useful as a procurement specification and a guide to
   implementors.  In this, he stands squarely on the shoulders of those
   who have gone before him, and depends largely on expert contributors
   for text.  Any credit is theirs; the errors are his.

   The content and form of this document are due, in large part, to the
   working group's chair, and document's original editor and author:
   Philip Almquist.  It is also largely due to the efforts of its
   previous editor, Frank Kastenholz.  Without their efforts, this
   document would not exist.

Table of Contents

   1. INTRODUCTION ........................................    6
   1.1 Reading this Document ..............................    8
   1.1.1 Organization .....................................    8
   1.1.2 Requirements .....................................    9
   1.1.3 Compliance .......................................   10
   1.2 Relationships to Other Standards ...................   11
   1.3 General Considerations .............................   12
   1.3.1 Continuing Internet Evolution ....................   12
   1.3.2 Robustness Principle .............................   13
   1.3.3 Error Logging ....................................   14



Baker                       Standards Track                     [Page 1]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   1.3.4 Configuration ....................................   14
   1.4 Algorithms .........................................   16
   2. INTERNET ARCHITECTURE ...............................   16
   2.1 Introduction .......................................   16
   2.2 Elements of the Architecture .......................   17
   2.2.1 Protocol Layering ................................   17
   2.2.2 Networks .........................................   19
   2.2.3 Routers ..........................................   20
   2.2.4 Autonomous Systems ...............................   21
   2.2.5 Addressing Architecture ..........................   21
   2.2.5.1 Classical IP Addressing Architecture ...........   21
   2.2.5.2 Classless Inter Domain Routing (CIDR) ..........   23
   2.2.6 IP Multicasting ..................................   24
   2.2.7 Unnumbered Lines and Networks Prefixes ...........   25
   2.2.8 Notable Oddities .................................   26
   2.2.8.1 Embedded Routers ...............................   26
   2.2.8.2 Transparent Routers ............................   27
   2.3 Router Characteristics .............................   28
   2.4 Architectural Assumptions ..........................   31
   3. LINK LAYER ..........................................   32
   3.1 INTRODUCTION .......................................   32
   3.2 LINK/INTERNET LAYER INTERFACE ......................   33
   3.3 SPECIFIC ISSUES ....................................   34
   3.3.1 Trailer Encapsulation ............................   34
   3.3.2 Address Resolution Protocol - ARP ................   34
   3.3.3 Ethernet and 802.3 Coexistence ...................   35
   3.3.4 Maximum Transmission Unit - MTU ..................   35
   3.3.5 Point-to-Point Protocol - PPP ....................   35
   3.3.5.1 Introduction ...................................   36
   3.3.5.2 Link Control Protocol (LCP) Options ............   36
   3.3.5.3 IP Control Protocol (IPCP) Options .............   38
   3.3.6 Interface Testing ................................   38
   4. INTERNET LAYER - PROTOCOLS ..........................   39
   4.1 INTRODUCTION .......................................   39
   4.2 INTERNET PROTOCOL - IP .............................   39
   4.2.1 INTRODUCTION .....................................   39
   4.2.2 PROTOCOL WALK-THROUGH ............................   40
   4.2.2.1 Options: RFC 791 Section 3.2 ...................   40
   4.2.2.2 Addresses in Options: RFC 791 Section 3.1 ......   42
   4.2.2.3 Unused IP Header Bits: RFC 791 Section 3.1 .....   43
   4.2.2.4 Type of Service: RFC 791 Section 3.1 ...........   44
   4.2.2.5 Header Checksum: RFC 791 Section 3.1 ...........   44
   4.2.2.6 Unrecognized Header Options: RFC 791,
           Section 3.1 ....................................   44
   4.2.2.7 Fragmentation: RFC 791 Section 3.2 .............   45
   4.2.2.8 Reassembly: RFC 791 Section 3.2 ................   46
   4.2.2.9 Time to Live: RFC 791 Section 3.2 ..............   46
   4.2.2.10 Multi-subnet Broadcasts: RFC 922 ..............   47



Baker                       Standards Track                     [Page 2]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   4.2.2.11 Addressing: RFC 791 Section 3.2 ...............   47
   4.2.3 SPECIFIC ISSUES ..................................   50
   4.2.3.1 IP Broadcast Addresses .........................   50
   4.2.3.2 IP Multicasting ................................   50
   4.2.3.3 Path MTU Discovery .............................   51
   4.2.3.4 Subnetting .....................................   51
   4.3 INTERNET CONTROL MESSAGE PROTOCOL - ICMP ...........   52
   4.3.1 INTRODUCTION .....................................   52
   4.3.2 GENERAL ISSUES ...................................   53
   4.3.2.1 Unknown Message Types ..........................   53
   4.3.2.2 ICMP Message TTL ...............................   53
   4.3.2.3 Original Message Header ........................   53
   4.3.2.4 ICMP Message Source Address ....................   53
   4.3.2.5 TOS and Precedence .............................   54
   4.3.2.6 Source Route ...................................   54
   4.3.2.7 When Not to Send ICMP Errors ...................   55
   4.3.2.8 Rate Limiting ..................................   56
   4.3.3 SPECIFIC ISSUES ..................................   56
   4.3.3.1 Destination Unreachable ........................   56
   4.3.3.2 Redirect .......................................   57
   4.3.3.3 Source Quench ..................................   57
   4.3.3.4 Time Exceeded ..................................   58
   4.3.3.5 Parameter Problem ..............................   58
   4.3.3.6 Echo Request/Reply .............................   58
   4.3.3.7 Information Request/Reply ......................   59
   4.3.3.8 Timestamp and Timestamp Reply ..................   59
   4.3.3.9 Address Mask Request/Reply .....................   61
   4.3.3.10 Router Advertisement and Solicitations ........   62
   4.4 INTERNET GROUP MANAGEMENT PROTOCOL - IGMP ..........   62
   5. INTERNET LAYER - FORWARDING .........................   63
   5.1 INTRODUCTION .......................................   63
   5.2 FORWARDING WALK-THROUGH ............................   63
   5.2.1 Forwarding Algorithm .............................   63
   5.2.1.1 General ........................................   64
   5.2.1.2 Unicast ........................................   64
   5.2.1.3 Multicast ......................................   65
   5.2.2 IP Header Validation .............................   67
   5.2.3 Local Delivery Decision ..........................   69
   5.2.4 Determining the Next Hop Address .................   71
   5.2.4.1 IP Destination Address .........................   72
   5.2.4.2 Local/Remote Decision ..........................   72
   5.2.4.3 Next Hop Address ...............................   74
   5.2.4.4 Administrative Preference ......................   77
   5.2.4.5 Load Splitting .................................   79
   5.2.5 Unused IP Header Bits: RFC-791 Section 3.1 .......   79
   5.2.6 Fragmentation and Reassembly:  RFC-791,
         Section 3.2 ......................................   80
   5.2.7 Internet Control Message Protocol - ICMP .........   80



Baker                       Standards Track                     [Page 3]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   5.2.7.1 Destination Unreachable ........................   80
   5.2.7.2 Redirect .......................................   82
   5.2.7.3 Time Exceeded ..................................   84
   5.2.8 INTERNET GROUP MANAGEMENT PROTOCOL - IGMP ........   84
   5.3 SPECIFIC ISSUES ....................................   85
   5.3.1 Time to Live (TTL) ...............................   85
   5.3.2 Type of Service (TOS) ............................   86
   5.3.3 IP Precedence ....................................   87
   5.3.3.1 Precedence-Ordered Queue Service ...............   88
   5.3.3.2 Lower Layer Precedence Mappings ................   89
   5.3.3.3 Precedence Handling For All Routers ............   90
   5.3.4 Forwarding of Link Layer Broadcasts ..............   92
   5.3.5 Forwarding of Internet Layer Broadcasts ..........   92
   5.3.5.1 Limited Broadcasts .............................   93
   5.3.5.2 Directed Broadcasts ............................   93
   5.3.5.3 All-subnets-directed Broadcasts ................   94
   5.3.5.4  Subnet-directed Broadcasts ....................   94
   5.3.6 Congestion Control ...............................   94
   5.3.7 Martian Address Filtering ........................   96
   5.3.8 Source Address Validation ........................   97
   5.3.9 Packet Filtering and Access Lists ................   97
   5.3.10 Multicast Routing ...............................   98
   5.3.11 Controls on Forwarding ..........................   98
   5.3.12 State Changes ...................................   99
   5.3.12.1 When a Router Ceases Forwarding ...............   99
   5.3.12.2 When a Router Starts Forwarding ...............  100
   5.3.12.3 When an Interface Fails or is Disabled ........  100
   5.3.12.4 When an Interface is Enabled ..................  100
   5.3.13 IP Options ......................................  101
   5.3.13.1 Unrecognized Options ..........................  101
   5.3.13.2 Security Option ...............................  101
   5.3.13.3 Stream Identifier Option ......................  101
   5.3.13.4 Source Route Options ..........................  101
   5.3.13.5 Record Route Option ...........................  102
   5.3.13.6 Timestamp Option ..............................  102
   6. TRANSPORT LAYER .....................................  103
   6.1 USER DATAGRAM PROTOCOL - UDP .......................  103
   6.2 TRANSMISSION CONTROL PROTOCOL - TCP ................  104
   7. APPLICATION LAYER - ROUTING PROTOCOLS ...............  106
   7.1 INTRODUCTION .......................................  106
   7.1.1 Routing Security Considerations ..................  106
   7.1.2 Precedence .......................................  107
   7.1.3 Message Validation ...............................  107
   7.2 INTERIOR GATEWAY PROTOCOLS .........................  107
   7.2.1 INTRODUCTION .....................................  107
   7.2.2 OPEN SHORTEST PATH FIRST - OSPF ..................  108
   7.2.3 INTERMEDIATE SYSTEM TO  INTERMEDIATE  SYSTEM  -
         DUAL IS-IS .......................................  108



Baker                       Standards Track                     [Page 4]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   7.3  EXTERIOR GATEWAY PROTOCOLS ........................  109
   7.3.1  INTRODUCTION ....................................  109
   7.3.2 BORDER GATEWAY PROTOCOL - BGP ....................  109
   7.3.2.1 Introduction ...................................  109
   7.3.2.2 Protocol Walk-through ..........................  110
   7.3.3 INTER-AS ROUTING WITHOUT AN  EXTERIOR  PROTOCOL
         ..................................................  110
   7.4 STATIC ROUTING .....................................  111
   7.5 FILTERING OF ROUTING INFORMATION ...................  112
   7.5.1 Route Validation .................................  113
   7.5.2 Basic Route Filtering ............................  113
   7.5.3 Advanced Route Filtering .........................  114
   7.6 INTER-ROUTING-PROTOCOL INFORMATION EXCHANGE ........  114
   8. APPLICATION LAYER - NETWORK  MANAGEMENT  PROTOCOLS
      .....................................................  115
   8.1 The Simple Network Management Protocol - SNMP ......  115
   8.1.1 SNMP Protocol Elements ...........................  115
   8.2 Community Table ....................................  116
   8.3 Standard MIBS ......................................  118
   8.4 Vendor Specific MIBS ...............................  119
   8.5 Saving Changes .....................................  120
   9. APPLICATION LAYER - MISCELLANEOUS PROTOCOLS .........  120
   9.1 BOOTP ..............................................  120
   9.1.1 Introduction .....................................  120
   9.1.2 BOOTP Relay Agents ...............................  121
   10. OPERATIONS AND MAINTENANCE .........................  122
   10.1 Introduction ......................................  122
   10.2 Router Initialization .............................  123
   10.2.1 Minimum Router Configuration ....................  123
   10.2.2 Address and Prefix Initialization ...............  124
   10.2.3 Network Booting using BOOTP and TFTP ............  125
   10.3 Operation and Maintenance .........................  126
   10.3.1 Introduction ....................................  126
   10.3.2 Out Of Band Access ..............................  127
   10.3.2 Router O&M Functions ............................  127
   10.3.2.1 Maintenance - Hardware Diagnosis ..............  127
   10.3.2.2 Control - Dumping and Rebooting ...............  127
   10.3.2.3 Control - Configuring the Router ..............  128
   10.3.2.4 Net Booting of System Software ................  128
   10.3.2.5 Detecting and responding to misconfiguration
            ...............................................  129
   10.3.2.6 Minimizing Disruption .........................  130
   10.3.2.7 Control - Troubleshooting Problems ............  130
   10.4 Security Considerations ...........................  131
   10.4.1 Auditing and Audit Trails .......................  131
   10.4.2 Configuration Control ...........................  132
   11. REFERENCES .........................................  133
   APPENDIX A. REQUIREMENTS FOR SOURCE-ROUTING HOSTS ......  145



Baker                       Standards Track                     [Page 5]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   APPENDIX B. GLOSSARY ...................................  146
   APPENDIX C. FUTURE DIRECTIONS ..........................  152
   APPENDIX D. Multicast Routing Protocols ................  154
   D.1 Introduction .......................................  154
   D.2 Distance  Vector  Multicast  Routing  Protocol  -
       DVMRP ..............................................  154
   D.3 Multicast Extensions to OSPF - MOSPF ...............  154
   D.4 Protocol Independent Multicast - PIM ...............  155
   APPENDIX E Additional Next-Hop  Selection  Algorithms
        ...................................................  155
   E.1. Some Historical Perspective .......................  155
   E.2. Additional Pruning Rules ..........................  157
   E.3 Some Route Lookup Algorithms .......................  159
   E.3.1 The Revised Classic Algorithm ....................  159
   E.3.2 The Variant Router Requirements Algorithm ........  160
   E.3.3 The OSPF Algorithm ...............................  160
   E.3.4 The Integrated IS-IS Algorithm ...................  162
   Security Considerations ................................  163
   APPENDIX F: HISTORICAL ROUTING PROTOCOLS ...............  164
   F.1 EXTERIOR GATEWAY PROTOCOL - EGP ....................  164
   F.1.1 Introduction .....................................  164
   F.1.2 Protocol Walk-through ............................  165
   F.2 ROUTING INFORMATION PROTOCOL - RIP .................  167
   F.2.1 Introduction .....................................  167
   F.2.2 Protocol Walk-Through ............................  167
   F.2.3 Specific Issues ..................................  172
   F.3 GATEWAY TO GATEWAY PROTOCOL - GGP ..................  173
   Acknowledgments ........................................  173
   Editor's Address .......................................  175

1. INTRODUCTION

  This memo replaces for RFC 1716, "Requirements for Internet Gateways"
  ([INTRO:1]).

  This memo defines and discusses requirements for devices that perform
  the network layer forwarding function of the Internet protocol suite.
  The Internet community usually refers to such devices as IP routers or
  simply routers; The OSI community refers to such devices as
  intermediate systems.  Many older Internet documents refer to these
  devices as gateways, a name which more recently has largely passed out
  of favor to avoid confusion with application gateways.

  An IP router can be distinguished from other sorts of packet switching
  devices in that a router examines the IP protocol header as part of
  the switching process.  It generally removes the Link Layer header a
  message was received with, modifies the IP header, and replaces the
  Link Layer header for retransmission.



Baker                       Standards Track                     [Page 6]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


  The authors of this memo recognize, as should its readers, that many
  routers support more than one protocol.  Support for multiple protocol
  suites will be required in increasingly large parts of the Internet in
  the future.  This memo, however, does not attempt to specify Internet
  requirements for protocol suites other than TCP/IP.

  This document enumerates standard protocols that a router connected to
  the Internet must use, and it incorporates by reference the RFCs and
  other documents describing the current specifications for these
  protocols.  It corrects errors in the referenced documents and adds
  additional discussion and guidance for an implementor.

  For each protocol, this memo also contains an explicit set of
  requirements, recommendations, and options.  The reader must
  understand that the list of requirements in this memo is incomplete by
  itself.  The complete set of requirements for an Internet protocol
  router is primarily defined in the standard protocol specification
  documents, with the corrections, amendments, and supplements contained
  in this memo.

  This memo should be read in conjunction with the Requirements for
  Internet Hosts RFCs ([INTRO:2] and [INTRO:3]).  Internet hosts and
  routers must both be capable of originating IP datagrams and receiving
  IP datagrams destined for them.  The major distinction between
  Internet hosts and routers is that routers implement forwarding
  algorithms, while Internet hosts do not require forwarding
  capabilities.  Any Internet host acting as a router must adhere to the
  requirements contained in this memo.

  The goal of open system interconnection dictates that routers must
  function correctly as Internet hosts when necessary.  To achieve this,
  this memo provides guidelines for such instances.  For simplification
  and ease of document updates, this memo tries to avoid overlapping
  discussions of host requirements with [INTRO:2] and [INTRO:3] and
  incorporates the relevant requirements of those documents by
  reference.  In some cases the requirements stated in [INTRO:2] and
  [INTRO:3] are superseded by this document.

  A good-faith implementation of the protocols produced after careful
  reading of the RFCs should differ from the requirements of this memo
  in only minor ways.  Producing such an implementation often requires
  some interaction with the Internet technical community, and must
  follow good communications software engineering practices.  In many
  cases, the requirements in this document are already stated or implied
  in the standard protocol documents, so that their inclusion here is,
  in a sense, redundant.  They were included because some past
  implementation has made the wrong choice, causing problems of
  interoperability, performance, and/or robustness.



Baker                       Standards Track                     [Page 7]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


  This memo includes discussion and explanation of many of the
  requirements and recommendations.  A simple list of requirements would
  be dangerous, because:

  o Some required features are more important than others, and some
     features are optional.

  o Some features are critical in some applications of routers but
     irrelevant in others.

  o There may be valid reasons why particular vendor products that are
     designed for restricted contexts might choose to use different
     specifications.

  However, the specifications of this memo must be followed to meet the
  general goal of arbitrary router interoperation across the diversity
  and complexity of the Internet.  Although most current implementations
  fail to meet these requirements in various ways, some minor and some
  major, this specification is the ideal towards which we need to move.

  These requirements are based on the current level of Internet
  architecture.  This memo will be updated as required to provide
  additional clarifications or to include additional information in
  those areas in which specifications are still evolving.

1.1 Reading this Document

1.1.1 Organization

  This memo emulates the layered organization used by [INTRO:2] and
  [INTRO:3].  Thus, Chapter 2 describes the layers found in the Internet
  architecture.  Chapter 3 covers the Link Layer.  Chapters 4 and 5 are
  concerned with the Internet Layer protocols and forwarding algorithms.
  Chapter 6 covers the Transport Layer.  Upper layer protocols are
  divided among Chapters 7, 8, and 9.  Chapter 7 discusses the protocols
  which routers use to exchange routing information with each other.
  Chapter 8 discusses network management.  Chapter 9 discusses other
  upper layer protocols.  The final chapter covers operations and
  maintenance features.  This organization was chosen for simplicity,
  clarity, and consistency with the Host Requirements RFCs.  Appendices
  to this memo include a bibliography, a glossary, and some conjectures
  about future directions of router standards.

  In describing the requirements, we assume that an implementation
  strictly mirrors the layering of the protocols.  However, strict
  layering is an imperfect model, both for the protocol suite and for
  recommended implementation approaches.  Protocols in different layers
  interact in complex and sometimes subtle ways, and particular



Baker                       Standards Track                     [Page 8]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


  functions often involve multiple layers.  There are many design
  choices in an implementation, many of which involve creative breaking
  of strict layering.  Every implementor is urged to read [INTRO:4] and
  [INTRO:5].

  Each major section of this memo is organized into the following
  subsections:

  (1) Introduction

  (2) Protocol Walk-Through - considers the protocol specification
       documents section-by-section, correcting errors, stating
       requirements that may be ambiguous or ill-defined, and providing
       further clarification or explanation.

  (3) Specific Issues - discusses protocol design and implementation
       issues that were not included in the walk-through.

  Under many of the individual topics in this memo, there is
  parenthetical material labeled DISCUSSION or IMPLEMENTATION.  This
  material is intended to give a justification, clarification or
  explanation to the preceding requirements text.  The implementation
  material contains suggested approaches that an implementor may want to
  consider.  The DISCUSSION and IMPLEMENTATION sections are not part of
  the standard.

1.1.2 Requirements

  In this memo, the words that are used to define the significance of
  each particular requirement are capitalized.  These words are:

  o MUST
     This word means that the item is an absolute requirement of the
     specification.  Violation of such a requirement is a fundamental
     error; there is no case where it is justified.

  o MUST IMPLEMENT
     This phrase means that this specification requires that the item be
     implemented, but does not require that it be enabled by default.

  o MUST NOT
     This phrase means that the item is an absolute prohibition of the
     specification.

  o SHOULD
     This word means that there may exist valid reasons in particular
     circumstances to ignore this item, but the full implications should
     be understood and the case carefully weighed before choosing a



Baker                       Standards Track                     [Page 9]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


     different course.

  o SHOULD IMPLEMENT
     This phrase is similar in meaning to SHOULD, but is used when we
     recommend that a particular feature be provided but does not
     necessarily recommend that it be enabled by default.

  o SHOULD NOT
     This phrase means that there may exist valid reasons in particular
     circumstances when the described behavior is acceptable or even
     useful.  Even so, the full implications should be understood and
     the case carefully weighed before implementing any behavior
     described with this label.

  o MAY
     This word means that this item is truly optional.  One vendor may
     choose to include the item because a particular marketplace
     requires it or because it enhances the product, for example;
     another vendor may omit the same item.

1.1.3 Compliance

  Some requirements are applicable to all routers.  Other requirements
  are applicable only to those which implement particular features or
  protocols.  In the following paragraphs, relevant refers to the union
  of the requirements applicable to all routers and the set of
  requirements applicable to a particular router because of the set of
  features and protocols it has implemented.

  Note that not all Relevant requirements are stated directly in this
  memo.  Various parts of this memo incorporate by reference sections of
  the Host Requirements specification, [INTRO:2] and [INTRO:3].  For
  purposes of determining compliance with this memo, it does not matter
  whether a Relevant requirement is stated directly in this memo or
  merely incorporated by reference from one of those documents.

  An implementation is said to be conditionally compliant if it
  satisfies all the Relevant MUST, MUST IMPLEMENT, and MUST NOT
  requirements.  An implementation is said to be unconditionally
  compliant if it is conditionally compliant and also satisfies all the
  Relevant SHOULD, SHOULD IMPLEMENT, and SHOULD NOT requirements.  An
  implementation is not compliant if it is not conditionally compliant
  (i.e., it fails to satisfy one or more of the Relevant MUST, MUST
  IMPLEMENT, or MUST NOT requirements).

  This specification occasionally indicates that an implementation
  SHOULD implement a management variable, and that it SHOULD have a
  certain default value.  An unconditionally compliant implementation



Baker                       Standards Track                    [Page 10]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


  implements the default behavior, and if there are other implemented
  behaviors implements the variable.  A conditionally compliant
  implementation clearly documents what the default setting of the
  variable is or, in the absence of the implementation of a variable,
  may be construed to be.  An implementation that both fails to
  implement the variable and chooses a different behavior is not
  compliant.

  For any of the SHOULD and SHOULD NOT requirements, a router may
  provide a configuration option that will cause the router to act other
  than as specified by the requirement.  Having such a configuration
  option does not void a router's claim to unconditional compliance if
  the option has a default setting, and that setting causes the router
  to operate in the required manner.

  Likewise, routers may provide, except where explicitly prohibited by
  this memo, options which cause them to violate MUST or MUST NOT
  requirements.  A router that provides such options is compliant
  (either fully or conditionally) if and only if each such option has a
  default setting that causes the router to conform to the requirements
  of this memo.  Please note that the authors of this memo, although
  aware of market realities, strongly recommend against provision of
  such options.  Requirements are labeled MUST or MUST NOT because
  experts in the field have judged them to be particularly important to
  interoperability or proper functioning in the Internet.  Vendors
  should weigh carefully the customer support costs of providing options
  that violate those rules.

  Of course, this memo is not a complete specification of an IP router,
  but rather is closer to what in the OSI world is called a profile.
  For example, this memo requires that a number of protocols be
  implemented.  Although most of the contents of their protocol
  specifications are not repeated in this memo, implementors are
  nonetheless required to implement the protocols according to those
  specifications.

1.2 Relationships to Other Standards

  There are several reference documents of interest in checking the
  status of protocol specifications and standardization:

    o INTERNET OFFICIAL PROTOCOL STANDARDS
       This document describes the Internet standards process and lists
       the standards status of the protocols.  As of this writing, the
       current version of this document is STD 1, RFC 1780, [ARCH:7].
       This document is periodically re-issued.  You should always
       consult an RFC repository and use the latest version of this
       document.



Baker                       Standards Track                    [Page 11]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


    o Assigned Numbers
       This document lists the assigned values of the parameters used in
       the various protocols.  For example, it lists IP protocol codes,
       TCP port numbers, Telnet Option Codes, ARP hardware types, and
       Terminal Type names.  As of this writing, the current version of
       this document is STD 2, RFC 1700, [INTRO:7].  This document is
       periodically re-issued.  You should always consult an RFC
       repository and use the latest version of this document.

    o Host Requirements
       This pair of documents reviews the specifications that apply to
       hosts and supplies guidance and clarification for any
       ambiguities.  Note that these requirements also apply to routers,
       except where otherwise specified in this memo.  As of this
       writing, the current versions of these documents are RFC 1122 and
       RFC 1123 (STD 3), [INTRO:2] and [INTRO:3].

    o Router Requirements (formerly Gateway Requirements)
       This memo.

   Note that these documents are revised and updated at different times;
   in case of differences between these documents, the most recent must
   prevail.

   These and other Internet protocol documents may be obtained from the:

                               The InterNIC
                              DS.INTERNIC.NET
                  InterNIC Directory and Database Service
                             info@internic.net
                              +1-908-668-6587
                       URL: http://ds.internic.net/

1.3 General Considerations

   There are several important lessons that vendors of Internet software
   have learned and which a new vendor should consider seriously.

1.3.1 Continuing Internet Evolution

   The enormous growth of the Internet has revealed problems of
   management and scaling in a large datagram based packet communication
   system.  These problems are being addressed, and as a result there
   will be continuing evolution of the specifications described in this
   memo.  New routing protocols, algorithms, and architectures are
   constantly being developed.  New internet layer protocols, and
   modifications to existing protocols, are also constantly being
   devised.  Routers play a crucial role in the Internet, and the number



Baker                       Standards Track                    [Page 12]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   of routers deployed in the Internet is much smaller than the number
   of hosts.  Vendors should therefore expect that router standards will
   continue to evolve much more quickly than host standards.  These
   changes will be carefully planned and controlled since there is
   extensive participation in this planning by the vendors and by the
   organizations responsible for operation of the networks.

   Development, evolution, and revision are characteristic of computer
   network protocols today, and this situation will persist for some
   years.  A vendor who develops computer communications software for
   the Internet protocol suite (or any other protocol suite!) and then
   fails to maintain and update that software for changing
   specifications is going to leave a trail of unhappy customers.  The
   Internet is a large communication network, and the users are in
   constant contact through it.  Experience has shown that knowledge of
   deficiencies in vendor software propagates quickly through the
   Internet technical community.

1.3.2 Robustness Principle

   At every layer of the protocols, there is a general rule (from
   [TRANS:2] by Jon Postel) whose application can lead to enormous
   benefits in robustness and interoperability:

                      Be conservative in what you do,
                be liberal in what you accept from others.

   Software should be written to deal with every conceivable error, no
   matter how unlikely.  Eventually a packet will come in with that
   particular combination of errors and attributes, and unless the
   software is prepared, chaos can ensue.  It is best to assume that the
   network is filled with malevolent entities that will send packets
   designed to have the worst possible effect.  This assumption will
   lead to suitably protective design.  The most serious problems in the
   Internet have been caused by unforeseen mechanisms triggered by low
   probability events; mere human malice would never have taken so
   devious a course!

   Adaptability to change must be designed into all levels of router
   software.  As a simple example, consider a protocol specification
   that contains an enumeration of values for a particular header field
   - e.g., a type field, a port number, or an error code; this
   enumeration must be assumed to be incomplete.  If the protocol
   specification defines four possible error codes, the software must
   not break when a fifth code is defined.  An undefined code might be
   logged, but it must not cause a failure.





Baker                       Standards Track                    [Page 13]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   The second part of the principal is almost as important: software on
   hosts or other routers may contain deficiencies that make it unwise
   to exploit legal but obscure protocol features.  It is unwise to
   stray far from the obvious and simple, lest untoward effects result
   elsewhere.  A corollary of this is watch out for misbehaving hosts;
   router software should be prepared to survive in the presence of
   misbehaving hosts.  An important function of routers in the Internet
   is to limit the amount of disruption such hosts can inflict on the
   shared communication facility.

1.3.3 Error Logging

   The Internet includes a great variety of systems, each implementing
   many protocols and protocol layers, and some of these contain bugs
   and misguided features in their Internet protocol software.  As a
   result of complexity, diversity, and distribution of function, the
   diagnosis of problems is often very difficult.

   Problem diagnosis will be aided if routers include a carefully
   designed facility for logging erroneous or strange events.  It is
   important to include as much diagnostic information as possible when
   an error is logged.  In particular, it is often useful to record the
   header(s) of a packet that caused an error.  However, care must be
   taken to ensure that error logging does not consume prohibitive
   amounts of resources or otherwise interfere with the operation of the
   router.

   There is a tendency for abnormal but harmless protocol events to
   overflow error logging files; this can be avoided by using a circular
   log, or by enabling logging only while diagnosing a known failure.
   It may be useful to filter and count duplicate successive messages.
   One strategy that seems to work well is to both:

   o Always count abnormalities and make such counts accessible through
      the management protocol (see Chapter 8); and
   o Allow the logging of a great variety of events to be selectively
      enabled.  For example, it might useful to be able to log
      everything or to log everything for host X.

   This topic is further discussed in [MGT:5].

1.3.4 Configuration

   In an ideal world, routers would be easy to configure, and perhaps
   even entirely self-configuring.  However, practical experience in the
   real world suggests that this is an impossible goal, and that many
   attempts by vendors to make configuration easy actually cause
   customers more grief than they prevent.  As an extreme example, a



Baker                       Standards Track                    [Page 14]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   router designed to come up and start routing packets without
   requiring any configuration information at all would almost certainly
   choose some incorrect parameter, possibly causing serious problems on
   any networks unfortunate enough to be connected to it.

   Often this memo requires that a parameter be a configurable option.
   There are several reasons for this.  In a few cases there currently
   is some uncertainty or disagreement about the best value and it may
   be necessary to update the recommended value in the future.  In other
   cases, the value really depends on external factors - e.g., the
   distribution of its communication load, or the speeds and topology of
   nearby networks - and self-tuning algorithms are unavailable and may
   be insufficient.  In some cases, configurability is needed because of
   administrative requirements.

   Finally, some configuration options are required to communicate with
   obsolete or incorrect implementations of the protocols, distributed
   without sources, that persist in many parts of the Internet.  To make
   correct systems coexist with these faulty systems, administrators
   must occasionally misconfigure the correct systems.  This problem
   will correct itself gradually as the faulty systems are retired, but
   cannot be ignored by vendors.

   When we say that a parameter must be configurable, we do not intend
   to require that its value be explicitly read from a configuration
   file at every boot time.  For many parameters, there is one value
   that is appropriate for all but the most unusual situations.  In such
   cases, it is quite reasonable that the parameter default to that
   value if not explicitly set.

   This memo requires a particular value for such defaults in some
   cases.  The choice of default is a sensitive issue when the
   configuration item controls accommodation of existing, faulty,
   systems.  If the Internet is to converge successfully to complete
   interoperability, the default values built into implementations must
   implement the official protocol, not misconfigurations to accommodate
   faulty implementations.  Although marketing considerations have led
   some vendors to choose misconfiguration defaults, we urge vendors to
   choose defaults that will conform to the standard.

   Finally, we note that a vendor needs to provide adequate
   documentation on all configuration parameters, their limits and
   effects.








Baker                       Standards Track                    [Page 15]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


1.4 Algorithms

   In several places in this memo, specific algorithms that a router
   ought to follow are specified.  These algorithms are not, per se,
   required of the router.  A router need not implement each algorithm
   as it is written in this document.  Rather, an implementation must
   present a behavior to the external world that is the same as a
   strict, literal, implementation of the specified algorithm.

   Algorithms are described in a manner that differs from the way a good
   implementor would implement them.  For expository purposes, a style
   that emphasizes conciseness, clarity, and independence from
   implementation details has been chosen.  A good implementor will
   choose algorithms and implementation methods that produce the same
   results as these algorithms, but may be more efficient or less
   general.

   We note that the art of efficient router implementation is outside
   the scope of this memo.

2. INTERNET ARCHITECTURE

   This chapter does not contain any requirements.  However, it does
   contain useful background information on the general architecture of
   the Internet and of routers.

   General background and discussion on the Internet architecture and
   supporting protocol suite can be found in the DDN Protocol Handbook
   [ARCH:1]; for background see for example [ARCH:2], [ARCH:3], and
   [ARCH:4].  The Internet architecture and protocols are also covered
   in an ever-growing number of textbooks, such as [ARCH:5] and
   [ARCH:6].

2.1 Introduction

   The Internet system consists of a number of interconnected packet
   networks supporting communication among host computers using the
   Internet protocols.  These protocols include the Internet Protocol
   (IP), the Internet Control Message Protocol (ICMP), the Internet
   Group Management Protocol (IGMP), and a variety transport and
   application protocols that depend upon them.  As was described in
   Section [1.2], the Internet Engineering Steering Group periodically
   releases an Official Protocols memo listing all the Internet
   protocols.

   All Internet protocols use IP as the basic data transport mechanism.
   IP is a datagram, or connectionless, internetwork service and
   includes provision for addressing, type-of-service specification,



Baker                       Standards Track                    [Page 16]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   fragmentation and reassembly, and security.  ICMP and IGMP are
   considered integral parts of IP, although they are architecturally
   layered upon IP.  ICMP provides error reporting, flow control,
   first-hop router redirection, and other maintenance and control
   functions.  IGMP provides the mechanisms by which hosts and routers
   can join and leave IP multicast groups.

   Reliable data delivery is provided in the Internet protocol suite by
   Transport Layer protocols such as the Transmission Control Protocol
   (TCP), which provides end-end retransmission, resequencing and
   connection control.  Transport Layer connectionless service is
   provided by the User Datagram Protocol (UDP).

2.2 Elements of the Architecture

2.2.1 Protocol Layering

   To communicate using the Internet system, a host must implement the
   layered set of protocols comprising the Internet protocol suite.  A
   host typically must implement at least one protocol from each layer.

   The protocol layers used in the Internet architecture are as follows
   [ARCH:7]:

   o Application Layer
      The Application Layer is the top layer of the Internet protocol
      suite.  The Internet suite does not further subdivide the
      Application Layer, although some application layer protocols do
      contain some internal sub-layering.  The application layer of the
      Internet suite essentially combines the functions of the top two
      layers - Presentation and Application - of the OSI Reference Model
      [ARCH:8].  The Application Layer in the Internet protocol suite
      also includes some of the function relegated to the Session Layer
      in the OSI Reference Model.

      We distinguish two categories of application layer protocols: user
      protocols that provide service directly to users, and support
      protocols that provide common system functions.  The most common
      Internet user protocols are:

      - Telnet (remote login)
      - FTP (file transfer)
      - SMTP (electronic mail delivery)

      There are a number of other standardized user protocols and many
      private user protocols.





Baker                       Standards Track                    [Page 17]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


      Support protocols, used for host name mapping, booting, and
      management include SNMP, BOOTP, TFTP, the Domain Name System (DNS)
      protocol, and a variety of routing protocols.

      Application Layer protocols relevant to routers are discussed in
      chapters 7, 8, and 9 of this memo.

   o Transport Layer
      The Transport Layer provides end-to-end communication services.
      This layer is roughly equivalent to the Transport Layer in the OSI
      Reference Model, except that it also incorporates some of OSI's
      Session Layer establishment and destruction functions.

      There are two primary Transport Layer protocols at present:

      - Transmission Control Protocol (TCP)
      - User Datagram Protocol (UDP)

      TCP is a reliable connection-oriented transport service that
      provides end-to-end reliability, resequencing, and flow control.
      UDP is a connectionless (datagram) transport service.  Other
      transport protocols have been developed by the research community,
      and the set of official Internet transport protocols may be
      expanded in the future.

      Transport Layer protocols relevant to routers are discussed in
      Chapter 6.

   o Internet Layer
      All Internet transport protocols use the Internet Protocol (IP) to
      carry data from source host to destination host.  IP is a
      connectionless or datagram internetwork service, providing no
      end-to-end delivery guarantees.  IP datagrams may arrive at the
      destination host damaged, duplicated, out of order, or not at all.
      The layers above IP are responsible for reliable delivery service
      when it is required.  The IP protocol includes provision for
      addressing, type-of-service specification, fragmentation and
      reassembly, and security.

      The datagram or connectionless nature of IP is a fundamental and
      characteristic feature of the Internet architecture.

      The Internet Control Message Protocol (ICMP) is a control protocol
      that is considered to be an integral part of IP, although it is
      architecturally layered upon IP - it uses IP to carry its data
      end-to-end.  ICMP provides error reporting, congestion reporting,
      and first-hop router redirection.




Baker                       Standards Track                    [Page 18]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


      The Internet Group Management Protocol (IGMP) is an Internet layer
      protocol used for establishing dynamic host groups for IP
      multicasting.

      The Internet layer protocols IP, ICMP, and IGMP are discussed in
      chapter 4.

   o Link Layer
      To communicate on a directly connected network, a host must
      implement the communication protocol used to interface to that
      network.  We call this a Link Layer protocol.

      Some older Internet documents refer to this layer as the Network
      Layer, but it is not the same as the Network Layer in the OSI
      Reference Model.

      This layer contains everything below the Internet Layer and above
      the Physical Layer (which is the media connectivity, normally
      electrical or optical, which encodes and transports messages).
      Its responsibility is the correct delivery of messages, among
      which it does not differentiate.

      Protocols in this Layer are generally outside the scope of
      Internet standardization; the Internet (intentionally) uses
      existing standards whenever possible.  Thus, Internet Link Layer
      standards usually address only address resolution and rules for
      transmitting IP packets over specific Link Layer protocols.
      Internet Link Layer standards are discussed in chapter 3.

2.2.2 Networks

   The constituent networks of the Internet system are required to
   provide only packet (connectionless) transport.  According to the IP
   service specification, datagrams can be delivered out of order, be
   lost or duplicated, and/or contain errors.

   For reasonable performance of the protocols that use IP (e.g., TCP),
   the loss rate of the network should be very low.  In networks
   providing connection-oriented service, the extra reliability provided
   by virtual circuits enhances the end-end robustness of the system,
   but is not necessary for Internet operation.

   Constituent networks may generally be divided into two classes:

     o Local-Area Networks (LANs)
        LANs may have a variety of designs.  LANs normally cover a small
        geographical area (e.g., a single building or plant site) and
        provide high bandwidth with low delays.  LANs may be passive



Baker                       Standards Track                    [Page 19]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


        (similar to Ethernet) or they may be active (such as ATM).

     o Wide-Area Networks (WANs)
        Geographically dispersed hosts and LANs are interconnected by
        wide-area networks, also called long-haul networks.  These
        networks may have a complex internal structure of lines and
        packet-switches, or they may be as simple as point-to-point
        lines.

2.2.3 Routers

   In the Internet model, constituent networks are connected together by
   IP datagram forwarders which are called routers or IP routers.  In
   this document, every use of the term router is equivalent to IP
   router.  Many older Internet documents refer to routers as gateways.

   Historically, routers have been realized with packet-switching
   software executing on a general-purpose CPU.  However, as custom
   hardware development becomes cheaper and as higher throughput is
   required, special purpose hardware is becoming increasingly common.
   This specification applies to routers regardless of how they are
   implemented.

   A router connects to two or more logical interfaces, represented by
   IP subnets or unnumbered point to point lines (discussed in section
   [2.2.7]).  Thus, it has at least one physical interface.  Forwarding
   an IP datagram generally requires the router to choose the address
   and relevant interface of the next-hop router or (for the final hop)
   the destination host.  This choice, called relaying or forwarding
   depends upon a route database within the router.  The route database
   is also called a routing table or forwarding table.  The term
   "router" derives from the process of building this route database;
   routing protocols and configuration interact in a process called
   routing.

   The routing database should be maintained dynamically to reflect the
   current topology of the Internet system.  A router normally
   accomplishes this by participating in distributed routing and
   reachability algorithms with other routers.

   Routers provide datagram transport only, and they seek to minimize
   the state information necessary to sustain this service in the
   interest of routing flexibility and robustness.

   Packet switching devices may also operate at the Link Layer; such
   devices are usually called bridges.  Network segments that are
   connected by bridges share the same IP network prefix forming a
   single IP subnet.  These other devices are outside the scope of this



Baker                       Standards Track                    [Page 20]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   document.

2.2.4 Autonomous Systems

   An Autonomous System (AS) is a connected segment of a network
   topology that consists of a collection of subnetworks (with hosts
   attached) interconnected by a set of routes.  The subnetworks and the
   routers are expected to be under the control of a single operations
   and maintenance (O&M) organization.  Within an AS routers may use one
   or more interior routing protocols, and sometimes several sets of
   metrics.  An AS is expected to present to other ASs an appearence of
   a coherent interior routing plan, and a consistent picture of the
   destinations reachable through the AS.  An AS is identified by an
   Autonomous System number.


   The concept of an AS plays an important role in the Internet routing
   (see Section 7.1).

2.2.5 Addressing Architecture

   An IP datagram carries 32-bit source and destination addresses, each
   of which is partitioned into two parts - a constituent network prefix
   and a host number on that network.  Symbolically:

      IP-address ::= { ,  }

   To finally deliver the datagram, the last router in its path must map
   the Host-number (or rest) part of an IP address to the host's Link
   Layer address.

2.2.5.1 Classical IP Addressing Architecture

   Although well documented elsewhere [INTERNET:2], it is useful to
   describe the historical use of the network prefix.  The language
   developed to describe it is used in this and other documents and
   permeates the thinking behind many protocols.

   The simplest classical network prefix is the Class A, B, C, D, or E
   network prefix.  These address ranges are discriminated by observing
   the values of the most significant bits of the address, and break the
   address into simple prefix and host number fields.  This is described
   in [INTERNET:18].  In short, the classification is:

        0xxx - Class A - general purpose unicast addresses with standard
        8 bit prefix
        10xx - Class B - general purpose unicast addresses with standard
        16 bit prefix



Baker                       Standards Track                    [Page 21]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


        110x - Class C - general purpose unicast addresses with standard
        24 bit prefix
        1110 - Class D - IP Multicast Addresses - 28 bit prefix, non-
        aggregatable
        1111 - Class E - reserved for experimental use

   This simple notion has been extended by the concept of subnets.
   These were introduced to allow arbitrary complexity of interconnected
   LAN structures within an organization, while insulating the Internet
   system against explosive growth in assigned network prefixes and
   routing complexity.  Subnets provide a multi-level hierarchical
   routing structure for the Internet system.  The subnet extension,
   described in [INTERNET:2], is a required part of the Internet
   architecture.  The basic idea is to partition the  field
   into two parts: a subnet number, and a true host number on that
   subnet:

      IP-address ::=
        { , ,  }

   The interconnected physical networks within an organization use the
   same network prefix but different subnet numbers.  The distinction
   between the subnets of such a subnetted network is not normally
   visible outside of that network.  Thus, routing in the rest of the
   Internet uses only the  part of the IP destination
   address.  Routers outside the network treat  and
    together as an uninterpreted rest part of the 32-bit IP
   address.  Within the subnetted network, the routers use the extended
   network prefix:

      { ,  }

   The bit positions containing this extended network number have
   historically been indicated by a 32-bit mask called the subnet mask.
   The  bits SHOULD be contiguous and fall between the
    and the  fields.  More up to date
   protocols do not refer to a subnet mask, but to a prefix length; the
   "prefix" portion of an address is that which would be selected by a
   subnet mask whose most significant bits are all ones and the rest are
   zeroes.  The length of the prefix equals the number of ones in the
   subnet mask.  This document assumes that all subnet masks are
   expressible as prefix lengths.

   The inventors of the subnet mechanism presumed that each piece of an
   organization's network would have only a single subnet number.  In
   practice, it has often proven necessary or useful to have several
   subnets share a single physical cable.  For this reason, routers
   should be capable of configuring multiple subnets on the same



Baker                       Standards Track                    [Page 22]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   physical interfaces, and treat them (from a routing or forwarding
   perspective) as though they were distinct physical interfaces.

2.2.5.2 Classless Inter Domain Routing (CIDR)

   The explosive growth of the Internet has forced a review of address
   assignment policies.  The traditional uses of general purpose (Class
   A, B, and C) networks have been modified to achieve better use of
   IP's 32-bit address space.  Classless Inter Domain Routing (CIDR)
   [INTERNET:15] is a method currently being deployed in the Internet
   backbones to achieve this added efficiency.  CIDR depends on
   deploying and routing to arbitrarily sized networks.  In this model,
   hosts and routers make no assumptions about the use of addressing in
   the internet.  The Class D (IP Multicast) and Class E (Experimental)
   address spaces are preserved, although this is primarily an
   assignment policy.

   By definition, CIDR comprises three elements:

     o topologically significant address assignment,
     o routing protocols that are capable of aggregating network layer
        reachability information, and
     o consistent forwarding algorithm ("longest match").

   The use of networks and subnets is now historical, although the
   language used to describe them remains in current use.  They have
   been replaced by the more tractable concept of a network prefix.  A
   network prefix is, by definition, a contiguous set of bits at the
   more significant end of the address that defines a set of systems;
   host numbers select among those systems.  There is no requirement
   that all the internet use network prefixes uniformly.  To collapse
   routing information, it is useful to divide the internet into
   addressing domains.  Within such a domain, detailed information is
   available about constituent networks; outside it, only the common
   network prefix is advertised.

   The classical IP addressing architecture used addresses and subnet
   masks to discriminate the host number from the network prefix.  With
   network prefixes, it is sufficient to indicate the number of bits in
   the prefix.  Both representations are in common use.  Architecturally
   correct subnet masks are capable of being represented using the
   prefix length description.  They comprise that subset of all possible
   bits patterns that have

     o a contiguous string of ones at the more significant end,
     o a contiguous string of zeros at the less significant end, and
     o no intervening bits.




Baker                       Standards Track                    [Page 23]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   Routers SHOULD always treat a route as a network prefix, and SHOULD
   reject configuration and routing information inconsistent with that
   model.

      IP-address ::= { ,  }

   An effect of the use of CIDR is that the set of destinations
   associated with address prefixes in the routing table may exhibit
   subset relationship.  A route describing a smaller set of
   destinations (a longer prefix) is said to be more specific than a
   route describing a larger set of destinations (a shorter prefix);
   similarly, a route describing a larger set of destinations (a shorter
   prefix) is said to be less specific than a route describing a smaller
   set of destinations (a longer prefix).  Routers must use the most
   specific matching route (the longest matching network prefix) when
   forwarding traffic.

2.2.6 IP Multicasting

   IP multicasting is an extension of Link Layer multicast to IP
   internets.  Using IP multicasts, a single datagram can be addressed
   to multiple hosts without sending it to all.  In the extended case,
   these hosts may reside in different address domains.  This collection
   of hosts is called a multicast group.  Each multicast group is
   represented as a Class D IP address.  An IP datagram sent to the
   group is to be delivered to each group member with the same best-
   effort delivery as that provided for unicast IP traffic.  The sender
   of the datagram does not itself need to be a member of the
   destination group.

   The semantics of IP multicast group membership are defined in
   [INTERNET:4].  That document describes how hosts and routers join and
   leave multicast groups.  It also defines a protocol, the Internet
   Group Management Protocol (IGMP), that monitors IP multicast group
   membership.

   Forwarding of IP multicast datagrams is accomplished either through
   static routing information or via a multicast routing protocol.
   Devices that forward IP multicast datagrams are called multicast
   routers.  They may or may not also forward IP unicasts.  Multicast
   datagrams are forwarded on the basis of both their source and
   destination addresses.  Forwarding of IP multicast packets is
   described in more detail in Section [5.2.1].  Appendix D discusses
   multicast routing protocols.







Baker                       Standards Track                    [Page 24]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


2.2.7 Unnumbered Lines and Networks Prefixes

   Traditionally, each network interface on an IP host or router has its
   own IP address.  This can cause inefficient use of the scarce IP
   address space, since it forces allocation of an IP network prefix to
   every point-to-point link.

   To solve this problem, a number of people have proposed and
   implemented the concept of unnumbered point to point lines.  An
   unnumbered point to point line does not have any network prefix
   associated with it.  As a consequence, the network interfaces
   connected to an unnumbered point to point line do not have IP
   addresses.

   Because the IP architecture has traditionally assumed that all
   interfaces had IP addresses, these unnumbered interfaces cause some
   interesting dilemmas.  For example, some IP options (e.g., Record
   Route) specify that a router must insert the interface address into
   the option, but an unnumbered interface has no IP address.  Even more
   fundamental (as we shall see in chapter 5) is that routes contain the
   IP address of the next hop router.  A router expects that this IP
   address will be on an IP (sub)net to which the router is connected.
   That assumption is of course violated if the only connection is an
   unnumbered point to point line.

   To get around these difficulties, two schemes have been conceived.
   The first scheme says that two routers connected by an unnumbered
   point to point line are not really two routers at all, but rather two
   half-routers that together make up a single virtual router.  The
   unnumbered point to point line is essentially considered to be an
   internal bus in the virtual router.  The two halves of the virtual
   router must coordinate their activities in such a way that they act
   exactly like a single router.

   This scheme fits in well with the IP architecture, but suffers from
   two important drawbacks.  The first is that, although it handles the
   common case of a single unnumbered point to point line, it is not
   readily extensible to handle the case of a mesh of routers and
   unnumbered point to point lines.  The second drawback is that the
   interactions between the half routers are necessarily complex and are
   not standardized, effectively precluding the connection of equipment
   from different vendors using unnumbered point to point lines.

   Because of these drawbacks, this memo has adopted an alternate
   scheme, which has been invented multiple times but which is probably
   originally attributable to Phil Karn.  In this scheme, a router that
   has unnumbered point to point lines also has a special IP address,
   called a router-id in this memo.  The router-id is one of the



Baker                       Standards Track                    [Page 25]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   router's IP addresses (a router is required to have at least one IP
   address).  This router-id is used as if it is the IP address of all
   unnumbered interfaces.

2.2.8 Notable Oddities

2.2.8.1 Embedded Routers

   A router may be a stand-alone computer system, dedicated to its IP
   router functions.  Alternatively, it is possible to embed router
   functions within a host operating system that supports connections to
   two or more networks.  The best-known example of an operating system
   with embedded router code is the Berkeley BSD system.  The embedded
   router feature seems to make building a network easy, but it has a
   number of hidden pitfalls:

   (1) If a host has only a single constituent-network interface, it
        should not act as a router.

        For example, hosts with embedded router code that gratuitously
        forward broadcast packets or datagrams on the same net often
        cause packet avalanches.

   (2) If a (multihomed) host acts as a router, it is subject to the
        requirements for routers contained in this document.

        For example, the routing protocol issues and the router control
        and monitoring problems are as hard and important for embedded
        routers as for stand-alone routers.

        Internet router requirements and specifications may change
        independently of operating system changes.  An administration
        that operates an embedded router in the Internet is strongly
        advised to maintain and update the router code.  This might
        require router source code.

   (3) When a host executes embedded router code, it becomes part of the
        Internet infrastructure.  Thus, errors in software or
        configuration can hinder communication between other hosts.  As
        a consequence, the host administrator must lose some autonomy.

        In many circumstances, a host administrator will need to disable
        router code embedded in the operating system.  For this reason,
        it should be straightforward to disable embedded router
        functionality.






Baker                       Standards Track                    [Page 26]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   (4) When a host running embedded router code is concurrently used for
        other services, the Operation and Maintenance requirements for
        the two modes of use may conflict.

        For example, router O&M will in many cases be performed remotely
        by an operations center; this may require privileged system
        access that the host administrator would not normally want to
        distribute.

2.2.8.2 Transparent Routers

   There are two basic models for interconnecting local-area networks
   and wide-area (or long-haul) networks in the Internet.  In the first,
   the local-area network is assigned a network prefix and all routers
   in the Internet must know how to route to that network.  In the
   second, the local-area network shares (a small part of) the address
   space of the wide-area network.  Routers that support this second
   model are called address sharing routers or transparent routers.  The
   focus of this memo is on routers that support the first model, but
   this is not intended to exclude the use of transparent routers.

   The basic idea of a transparent router is that the hosts on the
   local-area network behind such a router share the address space of
   the wide-area network in front of the router.  In certain situations
   this is a very useful approach and the limitations do not present
   significant drawbacks.

   The words in front and behind indicate one of the limitations of this
   approach: this model of interconnection is suitable only for a
   geographically (and topologically) limited stub environment.  It
   requires that there be some form of logical addressing in the network
   level addressing of the wide-area network.  IP addresses in the local
   environment map to a few (usually one) physical address in the wide-
   area network.  This mapping occurs in a way consistent with the { IP
   address <-> network address } mapping used throughout the wide-area
   network.

   Multihoming is possible on one wide-area network, but may present
   routing problems if the interfaces are geographically or
   topologically separated.  Multihoming on two (or more) wide-area
   networks is a problem due to the confusion of addresses.

   The behavior that hosts see from other hosts in what is apparently
   the same network may differ if the transparent router cannot fully
   emulate the normal wide-area network service.  For example, the
   ARPANET used a Link Layer protocol that provided a Destination Dead
   indication in response to an attempt to send to a host that was off-
   line.  However, if there were a transparent router between the



Baker                       Standards Track                    [Page 27]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   ARPANET and an Ethernet, a host on the ARPANET would not receive a
   Destination Dead indication for Ethernet hosts.

2.3 Router Characteristics

   An Internet router performs the following functions:

   (1) Conforms to specific Internet protocols specified in this
        document, including the Internet Protocol (IP), Internet Control
        Message Protocol (ICMP), and others as necessary.

   (2) Interfaces to two or more packet networks.  For each connected
        network the router must implement the functions required by that
        network.  These functions typically include:

        o Encapsulating and decapsulating the IP datagrams with the
           connected network framing (e.g., an Ethernet header and
           checksum),

        o Sending and receiving IP datagrams up to the maximum size
           supported by that network, this size is the network's Maximum
           Transmission Unit or MTU,

        o Translating the IP destination address into an appropriate
           network-level address for the connected network (e.g., an
           Ethernet hardware address), if needed, and

        o Responding to network flow control and error indications, if
           any.

        See chapter 3 (Link Layer).

   (3) Receives and forwards Internet datagrams.  Important issues in
        this process are buffer management, congestion control, and
        fairness.

        o Recognizes error conditions and generates ICMP error and
           information messages as required.

        o Drops datagrams whose time-to-live fields have reached zero.

        o Fragments datagrams when necessary to fit into the MTU of the
           next network.

        See chapter 4 (Internet Layer - Protocols) and chapter 5
        (Internet Layer - Forwarding) for more information.





Baker                       Standards Track                    [Page 28]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   (4) Chooses a next-hop destination for each IP datagram, based on the
        information in its routing database.  See chapter 5 (Internet
        Layer - Forwarding) for more information.

   (5) (Usually) supports an interior gateway protocol (IGP) to carry
        out distributed routing and reachability algorithms with the
        other routers in the same autonomous system.  In addition, some
        routers will need to support an exterior gateway protocol (EGP)
        to exchange topological information with other autonomous
        systems.  See chapter 7 (Application Layer - Routing Protocols)
        for more information.

   (6) Provides network management and system support facilities,
        including loading, debugging, status reporting, exception
        reporting and control.  See chapter 8 (Application Layer -
        Network Management Protocols) and chapter 10 (Operation and
        Maintenance) for more information.

   A router vendor will have many choices on power, complexity, and
   features for a particular router product.  It may be helpful to
   observe that the Internet system is neither homogeneous nor fully
   connected.  For reasons of technology and geography it is growing
   into a global interconnect system plus a fringe of LANs around the
   edge.  More and more these fringe LANs are becoming richly
   interconnected, thus making them less out on the fringe and more
   demanding on router requirements.

   o The global interconnect system is composed of a number of wide-area
      networks to which are attached routers of several Autonomous
      Systems (AS); there are relatively few hosts connected directly to
      the system.

   o Most hosts are connected to LANs.  Many organizations have clusters
      of LANs interconnected by local routers.  Each such cluster is
      connected by routers at one or more points into the global
      interconnect system.  If it is connected at only one point, a LAN
      is known as a stub network.

   Routers in the global interconnect system generally require:

   o Advanced Routing and Forwarding Algorithms

      These routers need routing algorithms that are highly dynamic,
      impose minimal processing and communication burdens, and offer
      type-of-service routing.  Congestion is still not a completely
      resolved issue (see Section [5.3.6]).  Improvements in these areas
      are expected, as the research community is actively working on
      these issues.



Baker                       Standards Track                    [Page 29]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   o High Availability

      These routers need to be highly reliable, providing 24 hours a
      day, 7 days a week service.  Equipment and software faults can
      have a wide-spread (sometimes global) effect.  In case of failure,
      they must recover quickly.  In any environment, a router must be
      highly robust and able to operate, possibly in a degraded state,
      under conditions of extreme congestion or failure of network
      resources.

   o Advanced O&M Features

      Internet routers normally operate in an unattended mode.  They
      will typically be operated remotely from a centralized monitoring
      center.  They need to provide sophisticated means for monitoring
      and measuring traffic and other events and for diagnosing faults.

   o High Performance

      Long-haul lines in the Internet today are most frequently full
      duplex 56 KBPS, DS1 (1.544 Mbps), or DS3 (45 Mbps) speeds.  LANs,
      which are half duplex multiaccess media, are typically Ethernet
      (10Mbps) and, to a lesser degree, FDDI (100Mbps).  However,
      network media technology is constantly advancing and higher speeds
      are likely in the future.

   The requirements for routers used in the LAN fringe (e.g., campus
   networks) depend greatly on the demands of the local networks.  These
   may be high or medium-performance devices, probably competitively
   procured from several different vendors and operated by an internal
   organization (e.g., a campus computing center).  The design of these
   routers should emphasize low average latency and good burst
   performance, together with delay and type-of-service sensitive
   resource management.  In this environment there may be less formal
   O&M but it will not be less important.  The need for the routing
   mechanism to be highly dynamic will become more important as networks
   become more complex and interconnected.  Users will demand more out
   of their local connections because of the speed of the global
   interconnects.

   As networks have grown, and as more networks have become old enough
   that they are phasing out older equipment, it has become increasingly
   imperative that routers interoperate with routers from other vendors.

   Even though the Internet system is not fully interconnected, many
   parts of the system need to have redundant connectivity.  Rich
   connectivity allows reliable service despite failures of
   communication lines and routers, and it can also improve service by



Baker                       Standards Track                    [Page 30]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   shortening Internet paths and by providing additional capacity.
   Unfortunately, this richer topology can make it much more difficult
   to choose the best path to a particular destination.

2.4 Architectural Assumptions

   The current Internet architecture is based on a set of assumptions
   about the communication system.  The assumptions most relevant to
   routers are as follows:

   o The Internet is a network of networks.

      Each host is directly connected to some particular network(s); its
      connection to the Internet is only conceptual.  Two hosts on the
      same network communicate with each other using the same set of
      protocols that they would use to communicate with hosts on distant
      networks.

   o Routers do not keep connection state information.

      To improve the robustness of the communication system, routers are
      designed to be stateless, forwarding each IP packet independently
      of other packets.  As a result, redundant paths can be exploited
      to provide robust service in spite of failures of intervening
      routers and networks.

      All state information required for end-to-end flow control and
      reliability is implemented in the hosts, in the transport layer or
      in application programs.  All connection control information is
      thus co-located with the end points of the communication, so it
      will be lost only if an end point fails.  Routers control message
      flow only indirectly, by dropping packets or increasing network
      delay.

      Note that future protocol developments may well end up putting
      some more state into routers.  This is especially likely for
      multicast routing, resource reservation, and flow based
      forwarding.

   o Routing complexity should be in the routers.

      Routing is a complex and difficult problem, and ought to be
      performed by the routers, not the hosts.  An important objective
      is to insulate host software from changes caused by the inevitable
      evolution of the Internet routing architecture.






Baker                       Standards Track                    [Page 31]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   o The system must tolerate wide network variation.

      A basic objective of the Internet design is to tolerate a wide
      range of network characteristics - e.g., bandwidth, delay, packet
      loss, packet reordering, and maximum packet size.  Another
      objective is robustness against failure of individual networks,
      routers, and hosts, using whatever bandwidth is still available.
      Finally, the goal is full open system interconnection: an Internet
      router must be able to interoperate robustly and effectively with
      any other router or Internet host, across diverse Internet paths.

      Sometimes implementors have designed for less ambitious goals.
      For example, the LAN environment is typically much more benign
      than the Internet as a whole; LANs have low packet loss and delay
      and do not reorder packets.  Some vendors have fielded
      implementations that are adequate for a simple LAN environment,
      but work badly for general interoperation.  The vendor justifies
      such a product as being economical within the restricted LAN
      market.  However, isolated LANs seldom stay isolated for long.
      They are soon connected to each other, to organization-wide
      internets, and eventually to the global Internet system.  In the
      end, neither the customer nor the vendor is served by incomplete
      or substandard routers.

      The requirements in this document are designed for a full-function
      router.  It is intended that fully compliant routers will be
      usable in almost any part of the Internet.

3. LINK LAYER

   Although [INTRO:1] covers Link Layer standards (IP over various link
   layers, ARP, etc.), this document anticipates that Link-Layer
   material will be covered in a separate Link Layer Requirements
   document.  A Link-Layer Requirements document would be applicable to
   both hosts and routers.  Thus, this document will not obsolete the
   parts of [INTRO:1] that deal with link-layer issues.

3.1 INTRODUCTION

   Routers have essentially the same Link Layer protocol requirements as
   other sorts of Internet systems.  These requirements are given in
   chapter 3 of Requirements for Internet Gateways [INTRO:1].  A router
   MUST comply with its requirements and SHOULD comply with its
   recommendations.  Since some of the material in that document has
   become somewhat dated, some additional requirements and explanations
   are included below.





Baker                       Standards Track                    [Page 32]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   DISCUSSION
      It is expected that the Internet community will produce a
      Requirements for Internet Link Layer standard which will supersede
      both this chapter and the chapter entitled "INTERNET LAYER
      PROTOCOLS" in [INTRO:1].

3.2 LINK/INTERNET LAYER INTERFACE

   This document does not attempt to specify the interface between the
   Link Layer and the upper layers.  However, note well that other parts
   of this document, particularly chapter 5, require various sorts of
   information to be passed across this layer boundary.

   This section uses the following definitions:

   o Source physical address

      The source physical address is the Link Layer address of the host
      or router from which the packet was received.

   o Destination physical address

      The destination physical address is the Link Layer address to
      which the packet was sent.

   The information that must pass from the Link Layer to the
   Internetwork Layer for each received packet is:

   (1) The IP packet [5.2.2],

   (2) The length of the data portion (i.e., not including the Link-
        Layer framing) of the Link Layer frame [5.2.2],

   (3) The identity of the physical interface from which the IP packet
        was received [5.2.3], and

   (4) The classification of the packet's destination physical address
        as a Link Layer unicast, broadcast, or multicast [4.3.2],
        [5.3.4].

   In addition, the Link Layer also should provide:

   (5) The source physical address.

   The information that must pass from the Internetwork Layer to the
   Link Layer for each transmitted packet is:





Baker                       Standards Track                    [Page 33]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   (1) The IP packet [5.2.1]

   (2) The length of the IP packet [5.2.1]

   (3) The destination physical interface [5.2.1]

   (4) The next hop IP address [5.2.1]

   In addition, the Internetwork Layer also should provide:

   (5) The Link Layer priority value [5.3.3.2]

   The Link Layer must also notify the Internetwork Layer if the packet
   to be transmitted causes a Link Layer precedence-related error
   [5.3.3.3].

3.3 SPECIFIC ISSUES

3.3.1 Trailer Encapsulation

   Routers that can connect to ten megabit Ethernets MAY be able to
   receive and forward Ethernet packets encapsulated using the trailer
   encapsulation described in [LINK:1].  However, a router SHOULD NOT
   originate trailer encapsulated packets.  A router MUST NOT originate
   trailer encapsulated packets without first verifying, using the
   mechanism described in [INTRO:2], that the immediate destination of
   the packet is willing and able to accept trailer-encapsulated
   packets.  A router SHOULD NOT agree (using these mechanisms) to
   accept trailer-encapsulated packets.

3.3.2 Address Resolution Protocol - ARP

   Routers that implement ARP MUST be compliant and SHOULD be
   unconditionally compliant with the requirements in [INTRO:2].

   The link layer MUST NOT report a Destination Unreachable error to IP
   solely because there is no ARP cache entry for a destination; it
   SHOULD queue up to a small number of datagrams breifly while
   performing the ARP request/reply sequence, and reply that the
   destination is unreachable to one of the queued datagrams only when
   this proves fruitless.

   A router MUST not believe any ARP reply that claims that the Link
   Layer address of another host or router is a broadcast or multicast
   address.






Baker                       Standards Track                    [Page 34]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


3.3.3 Ethernet and 802.3 Coexistence

   Routers that can connect to ten megabit Ethernets MUST be compliant
   and SHOULD be unconditionally compliant with the Ethernet
   requirements of [INTRO:2].

3.3.4 Maximum Transmission Unit - MTU

   The MTU of each logical interface MUST be configurable within the
   range of legal MTUs for the interface.

   Many Link Layer protocols define a maximum frame size that may be
   sent.  In such cases, a router MUST NOT allow an MTU to be set which
   would allow sending of frames larger than those allowed by the Link
   Layer protocol.  However, a router SHOULD be willing to receive a
   packet as large as the maximum frame size even if that is larger than
   the MTU.

   DISCUSSION
      Note that this is a stricter requirement than imposed on hosts by
      [INTRO:2], which requires that the MTU of each physical interface
      be configurable.

      If a network is using an MTU smaller than the maximum frame size
      for the Link Layer, a router may receive packets larger than the
      MTU from misconfigured and incompletely initialized hosts.  The
      Robustness Principle indicates that the router should successfully
      receive these packets if possible.

3.3.5 Point-to-Point Protocol - PPP

   Contrary to [INTRO:1], the Internet does have a standard point to
   point line protocol: the Point-to-Point Protocol (PPP), defined in
   [LINK:2], [LINK:3], [LINK:4], and [LINK:5].

   A point to point interface is any interface that is designed to send
   data over a point to point line.  Such interfaces include telephone,
   leased, dedicated or direct lines (either 2 or 4 wire), and may use
   point to point channels or virtual circuits of multiplexed interfaces
   such as ISDN.  They normally use a standardized modem or bit serial
   interface (such as RS-232, RS-449 or V.35), using either synchronous
   or asynchronous clocking.  Multiplexed interfaces often have special
   physical interfaces.

   A general purpose serial interface uses the same physical media as a
   point to point line, but supports the use of link layer networks as
   well as point to point connectivity.  Link layer networks (such as
   X.25 or Frame Relay) use an alternative IP link layer specification.



Baker                       Standards Track                    [Page 35]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   Routers that implement point to point or general purpose serial
   interfaces MUST IMPLEMENT PPP.

   PPP MUST be supported on all general purpose serial interfaces on a
   router.  The router MAY allow the line to be configured to use point
   to point line protocols other than PPP.  Point to point interfaces
   SHOULD either default to using PPP when enabled or require
   configuration of the link layer protocol before being enabled.
   General purpose serial interfaces SHOULD require configuration of the
   link layer protocol before being enabled.

3.3.5.1 Introduction

   This section provides guidelines to router implementors so that they
   can ensure interoperability with other routers using PPP over either
   synchronous or asynchronous links.

   It is critical that an implementor understand the semantics of the
   option negotiation mechanism.  Options are a means for a local device
   to indicate to a remote peer what the local device will accept from
   the remote peer, not what it wishes to send.  It is up to the remote
   peer to decide what is most convenient to send within the confines of
   the set of options that the local device has stated that it can
   accept.  Therefore it is perfectly acceptable and normal for a remote
   peer to ACK all the options indicated in an LCP Configuration Request
   (CR) even if the remote peer does not support any of those options.
   Again, the options are simply a mechanism for either device to
   indicate to its peer what it will accept, not necessarily what it
   will send.

3.3.5.2 Link Control Protocol (LCP) Options

   The PPP Link Control Protocol (LCP) offers a number of options that
   may be negotiated.  These options include (among others) address and
   control field compression, protocol field compression, asynchronous
   character map, Maximum Receive Unit (MRU), Link Quality Monitoring
   (LQM), magic number (for loopback detection), Password Authentication
   Protocol (PAP), Challenge Handshake Authentication Protocol (CHAP),
   and the 32-bit Frame Check Sequence (FCS).

   A router MAY use address/control field compression on either
   synchronous or asynchronous links.  A router MAY use protocol field
   compression on either synchronous or asynchronous links.  A router
   that indicates that it can accept these compressions MUST be able to
   accept uncompressed PPP header information also.






Baker                       Standards Track                    [Page 36]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   DISCUSSION
      These options control the appearance of the PPP header.  Normally
      the PPP header consists of the address, the control field, and the
      protocol field.  The address, on a point to point line, is 0xFF,
      indicating "broadcast".  The control field is 0x03, indicating
      "Unnumbered Information." The Protocol Identifier is a two byte
      value indicating the contents of the data area of the frame.  If a
      system negotiates address and control field compression it
      indicates to its peer that it will accept PPP frames that have or
      do not have these fields at the front of the header.  It does not
      indicate that it will be sending frames with these fields removed.

      Protocol field compression, when negotiated, indicates that the
      system is willing to receive protocol fields compressed to one
      byte when this is legal.  There is no requirement that the sender
      do so.

      Use of address/control field compression is inconsistent with the
      use of numbered mode (reliable) PPP.

   IMPLEMENTATION
      Some hardware does not deal well with variable length header
      information.  In those cases it makes most sense for the remote
      peer to send the full PPP header.  Implementations may ensure this
      by not sending the address/control field and protocol field
      compression options to the remote peer.  Even if the remote peer
      has indicated an ability to receive compressed headers there is no
      requirement for the local router to send compressed headers.

   A router MUST negotiate the Asynchronous Control Character Map (ACCM)
   for asynchronous PPP links, but SHOULD NOT negotiate the ACCM for
   synchronous links.  If a router receives an attempt to negotiate the
   ACCM over a synchronous link, it MUST ACKnowledge the option and then
   ignore it.

   DISCUSSION
      There are implementations that offer both synchronous and
      asynchronous modes of operation and may use the same code to
      implement the option negotiation.  In this situation it is
      possible that one end or the other may send the ACCM option on a
      synchronous link.

   A router SHOULD properly negotiate the maximum receive unit (MRU).
   Even if a system negotiates an MRU smaller than 1,500 bytes, it MUST
   be able to receive a 1,500 byte frame.

   A router SHOULD negotiate and enable the link quality monitoring
   (LQM) option.



Baker                       Standards Track                    [Page 37]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   DISCUSSION
      This memo does not specify a policy for deciding whether the
      link's quality is adequate.  However, it is important (see Section
      [3.3.6]) that a router disable failed links.

   A router SHOULD implement and negotiate the magic number option for
   loopback detection.

   A router MAY support the authentication options (PAP - Password
   Authentication Protocol, and/or CHAP - Challenge Handshake
   Authentication Protocol).

   A router MUST support 16-bit CRC frame check sequence (FCS) and MAY
   support the 32-bit CRC.

3.3.5.3 IP Control Protocol (IPCP) Options

   A router MAY offer to perform IP address negotiation.  A router MUST
   accept a refusal (REJect) to perform IP address negotiation from the
   peer.

   Routers operating at link speeds of 19,200 BPS or less SHOULD
   implement and offer to perform Van Jacobson header compression.
   Routers that implement VJ compression SHOULD implement an
   administrative control enabling or disabling it.

3.3.6 Interface Testing

   A router MUST have a mechanism to allow routing software to determine
   whether a physical interface is available to send packets or not; on
   multiplexed interfaces where permanent virtual circuits are opened
   for limited sets of neighbors, the router must also be able to
   determine whether the virtual circuits are viable.  A router SHOULD
   have a mechanism to allow routing software to judge the quality of a
   physical interface.  A router MUST have a mechanism for informing the
   routing software when a physical interface becomes available or
   unavailable to send packets because of administrative action.  A
   router MUST have a mechanism for informing the routing software when
   it detects a Link level interface has become available or
   unavailable, for any reason.

   DISCUSSION
      It is crucial that routers have workable mechanisms for
      determining that their network connections are functioning
      properly.  Failure to detect link loss, or failure to take the
      proper actions when a problem is detected, can lead to black
      holes.




Baker                       Standards Track                    [Page 38]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


      The mechanisms available for detecting problems with network
      connections vary considerably, depending on the Link Layer
      protocols in use and the interface hardware.  The intent is to
      maximize the capability to detect failures within the Link-Layer
      constraints.

4. INTERNET LAYER - PROTOCOLS

4.1 INTRODUCTION

   This chapter and chapter 5 discuss the protocols used at the Internet
   Layer: IP, ICMP, and IGMP.  Since forwarding is obviously a crucial
   topic in a document discussing routers, chapter 5 limits itself to
   the aspects of the protocols that directly relate to forwarding.  The
   current chapter contains the remainder of the discussion of the
   Internet Layer protocols.

4.2 INTERNET PROTOCOL - IP

4.2.1 INTRODUCTION

   Routers MUST implement the IP protocol, as defined by [INTERNET:1].
   They MUST also implement its mandatory extensions: subnets (defined
   in [INTERNET:2]), IP broadcast (defined in [INTERNET:3]), and
   Classless Inter-Domain Routing (CIDR, defined in [INTERNET:15]).

   Router implementors need not consider compliance with the section of
   [INTRO:2] entitled "Internet Protocol -- IP," as that section is
   entirely duplicated or superseded in this document.  A router MUST be
   compliant, and SHOULD be unconditionally compliant, with the
   requirements of the section entitled "SPECIFIC ISSUES" relating to IP
   in [INTRO:2].

   In the following, the action specified in certain cases is to
   silently discard a received datagram.  This means that the datagram
   will be discarded without further processing and that the router will
   not send any ICMP error message (see Section [4.3]) as a result.
   However, for diagnosis of problems a router SHOULD provide the
   capability of logging the error (see Section [1.3.3]), including the
   contents of the silently discarded datagram, and SHOULD count
   datagrams discarded.










Baker                       Standards Track                    [Page 39]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


4.2.2 PROTOCOL WALK-THROUGH

   RFC 791 [INTERNET:1] is the specification for the Internet Protocol.

4.2.2.1 Options: RFC 791 Section 3.2

   In datagrams received by the router itself, the IP layer MUST
   interpret IP options that it understands and preserve the rest
   unchanged for use by higher layer protocols.

   Higher layer protocols may require the ability to set IP options in
   datagrams they send or examine IP options in datagrams they receive.
   Later sections of this document discuss specific IP option support
   required by higher layer protocols.

   DISCUSSION
      Neither this memo nor [INTRO:2] define the order in which a
      receiver must process multiple options in the same IP header.
      Hosts and routers originating datagrams containing multiple
      options must be aware that this introduces an ambiguity in the
      meaning of certain options when combined with a source-route
      option.

   Here are the requirements for specific IP options:

   (a) Security Option

        Some environments require the Security option in every packet
        originated or received.  Routers SHOULD IMPLEMENT the revised
        security option described in [INTERNET:5].

   DISCUSSION
      Note that the security options described in [INTERNET:1] and RFC
      1038 ([INTERNET:16]) are obsolete.

   (b) Stream Identifier Option

         This option is obsolete; routers SHOULD NOT place this option
         in a datagram that the router originates.  This option MUST be
         ignored in datagrams received by the router.

   (c) Source Route Options

         A router MUST be able to act as the final destination of a
         source route.  If a router receives a packet containing a
         completed source route, the packet has reached its final
         destination.  In such an option, the pointer points beyond the
         last field and the destination address in the IP header



Baker                       Standards Track                    [Page 40]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


         addresses the router.  The option as received (the recorded
         route) MUST be passed up to the transport layer (or to ICMP
         message processing).

         In the general case, a correct response to a source-routed
         datagram traverses the same route.  A router MUST provide a
         means whereby transport protocols and applications can reverse
         the source route in a received datagram.  This reversed source
         route MUST be inserted into datagrams they originate (see
         [INTRO:2] for details) when the router is unaware of policy
         constraints.  However, if the router is policy aware, it MAY
         select another path.

         Some applications in the router MAY require that the user be
         able to enter a source route.

         A router MUST NOT originate a datagram containing multiple
         source route options.  What a router should do if asked to
         forward a packet containing multiple source route options is
         described in Section [5.2.4.1].

         When a source route option is created (which would happen when
         the router is originating a source routed datagram or is
         inserting a source route option as a result of a special
         filter), it MUST be correctly formed even if it is being
         created by reversing a recorded route that erroneously includes
         the source host (see case (B) in the discussion below).

   DISCUSSION
      Suppose a source routed datagram is to be routed from source _S to
      destination D via routers G1, G2, Gn.  Source S constructs a
      datagram with G1's IP address as its destination address, and a
      source route option to get the datagram the rest of the way to its
      destination.  However, there is an ambiguity in the specification
      over whether the source route option in a datagram sent out by S
      should be (A) or (B):

      (A): {>>G2, G3, ... Gn, D} <--- CORRECT

      (B): {S, >>G2, G3, ... Gn, D} <---- WRONG

      (where >> represents the pointer).  If (A) is sent, the datagram
      received at D will contain the option: {G1, G2, ... Gn >>}, with S
      and D as the IP source and destination addresses.  If (B) were
      sent, the datagram received at D would again contain S and D as
      the same IP source and destination addresses, but the option would
      be: {S, G1, ...Gn >>}; i.e., the originating host would be the
      first hop in the route.



Baker                       Standards Track                    [Page 41]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   (d) Record Route Option

         Routers MAY support the Record Route option in datagrams
         originated by the router.

   (e) Timestamp Option

         Routers MAY support the timestamp option in datagrams
         originated by the router.  The following rules apply:

         o When originating a datagram containing a Timestamp Option, a
            router MUST record a timestamp in the option if

            - Its Internet address fields are not pre-specified or
            - Its first pre-specified address is the IP address of the
               logical interface over which the datagram is being sent
               (or the router's router-id if the datagram is being sent
               over an unnumbered interface).

         o If the router itself receives a datagram containing a
            Timestamp Option, the router MUST insert the current time
            into the Timestamp Option (if there is space in the option
            to do so) before passing the option to the transport layer
            or to ICMP for processing.  If space is not present, the
            router MUST increment the Overflow Count in the option.

         o A timestamp value MUST follow the rules defined in [INTRO:2].

   IMPLEMENTATION
      To maximize the utility of the timestamps contained in the
      timestamp option, the timestamp inserted should be, as nearly as
      practical, the time at which the packet arrived at the router.
      For datagrams originated by the router, the timestamp inserted
      should be, as nearly as practical, the time at which the datagram
      was passed to the Link Layer for transmission.

      The timestamp option permits the use of a non-standard time clock,
      but the use of a non-synchronized clock limits the utility of the
      time stamp.  Therefore, routers are well advised to implement the
      Network Time Protocol for the purpose of synchronizing their
      clocks.

4.2.2.2 Addresses in Options: RFC 791 Section 3.1

   Routers are called upon to insert their address into Record Route,
   Strict Source and Record Route, Loose Source and Record Route, or
   Timestamp Options.  When a router inserts its address into such an
   option, it MUST use the IP address of the logical interface on which



Baker                       Standards Track                    [Page 42]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   the packet is being sent.  Where this rule cannot be obeyed because
   the output interface has no IP address (i.e., is an unnumbered
   interface), the router MUST instead insert its router-id.  The
   router's router-id is one of the router's IP addresses.  The Router
   ID may be specified on a system basis or on a per-link basis.  Which
   of the router's addresses is used as the router-id MUST NOT change
   (even across reboots) unless changed by the network manager.
   Relevant management changes include reconfiguration of the router
   such that the IP address used as the router-id ceases to be one of
   the router's IP addresses.  Routers with multiple unnumbered
   interfaces MAY have multiple router-id's.  Each unnumbered interface
   MUST be associated with a particular router-id.  This association
   MUST NOT change (even across reboots) without reconfiguration of the
   router.

   DISCUSSION
      This specification does not allow for routers that do not have at
      least one IP address.  We do not view this as a serious
      limitation, since a router needs an IP address to meet the
      manageability requirements of Chapter [8] even if the router is
      connected only to point-to-point links.

   IMPLEMENTATION

      One possible method of choosing the router-id that fulfills this
      requirement is to use the numerically smallest (or greatest) IP
      address (treating the address as a 32-bit integer) that is
      assigned to the router.

4.2.2.3 Unused IP Header Bits: RFC 791 Section 3.1

   The IP header contains two reserved bits: one in the Type of Service
   byte and the other in the Flags field.  A router MUST NOT set either
   of these bits to one in datagrams originated by the router.  A router
   MUST NOT drop (refuse to receive or forward) a packet merely because
   one or more of these reserved bits has a non-zero value; i.e., the
   router MUST NOT check the values of thes bits.

   DISCUSSION
      Future revisions to the IP protocol may make use of these unused
      bits.  These rules are intended to ensure that these revisions can
      be deployed without having to simultaneously upgrade all routers
      in the Internet.








Baker                       Standards Track                    [Page 43]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


4.2.2.4 Type of Service: RFC 791 Section 3.1

   The Type-of-Service byte in the IP header is divided into three
   sections: the Precedence field (high-order 3 bits), a field that is
   customarily called Type of Service or TOS (next 4 bits), and a
   reserved bit (the low order bit).

   Rules governing the reserved bit were described in Section [4.2.2.3].

   A more extensive discussion of the TOS field and its use can be found
   in [ROUTE:11].

   The description of the IP Precedence field is superseded by Section
   [5.3.3].  RFC 795, Service Mappings, is obsolete and SHOULD NOT be
   implemented.

4.2.2.5 Header Checksum: RFC 791 Section 3.1

   As stated in Section [5.2.2], a router MUST verify the IP checksum of
   any packet that is received, and MUST discard messages containing
   invalid checksums.  The router MUST NOT provide a means to disable
   this checksum verification.

   A router MAY use incremental IP header checksum updating when the
   only change to the IP header is the time to live.  This will reduce
   the possibility of undetected corruption of the IP header by the
   router.  See [INTERNET:6] for a discussion of incrementally updating
   the checksum.

   IMPLEMENTATION
      A more extensive description of the IP checksum, including
      extensive implementation hints, can be found in [INTERNET:6] and
      [INTERNET:7].

4.2.2.6 Unrecognized Header Options: RFC 791 Section 3.1

   A router MUST ignore IP options which it does not recognize.  A
   corollary of this requirement is that a router MUST implement the End
   of Option List option and the No Operation option, since neither
   contains an explicit length.

   DISCUSSION
      All future IP options will include an explicit length.








Baker                       Standards Track                    [Page 44]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


4.2.2.7 Fragmentation: RFC 791 Section 3.2

   Fragmentation, as described in [INTERNET:1], MUST be supported by a
   router.

   When a router fragments an IP datagram, it SHOULD minimize the number
   of fragments.  When a router fragments an IP datagram, it SHOULD send
   the fragments in order.  A fragmentation method that may generate one
   IP fragment that is significantly smaller than the other MAY cause
   the first IP fragment to be the smaller one.

   DISCUSSION
      There are several fragmentation techniques in common use in the
      Internet.  One involves splitting the IP datagram into IP
      fragments with the first being MTU sized, and the others being
      approximately the same size, smaller than the MTU.  The reason for
      this is twofold.  The first IP fragment in the sequence will be
      the effective MTU of the current path between the hosts, and the
      following IP fragments are sized to minimize the further
      fragmentation of the IP datagram.  Another technique is to split
      the IP datagram into MTU sized IP fragments, with the last
      fragment being the only one smaller, as described in [INTERNET:1].

      A common trick used by some implementations of TCP/IP is to
      fragment an IP datagram into IP fragments that are no larger than
      576 bytes when the IP datagram is to travel through a router.
      This is intended to allow the resulting IP fragments to pass the
      rest of the path without further fragmentation.  This would,
      though, create more of a load on the destination host, since it
      would have a larger number of IP fragments to reassemble into one
      IP datagram.  It would also not be efficient on networks where the
      MTU only changes once and stays much larger than 576 bytes.
      Examples include LAN networks such as an IEEE 802.5 network with a
      MTU of 2048 or an Ethernet network with an MTU of 1500).

      One other fragmentation technique discussed was splitting the IP
      datagram into approximately equal sized IP fragments, with the
      size less than or equal to the next hop network's MTU.  This is
      intended to minimize the number of fragments that would result
      from additional fragmentation further down the path, and assure
      equal delay for each fragment.

      Routers SHOULD generate the least possible number of IP fragments.

      Work with slow machines leads us to believe that if it is
      necessary to fragment messages, sending the small IP fragment
      first maximizes the chance of a host with a slow interface of
      receiving all the fragments.



Baker                       Standards Track                    [Page 45]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


4.2.2.8 Reassembly: RFC 791 Section 3.2

   As specified in the corresponding section of [INTRO:2], a router MUST
   support reassembly of datagrams that it delivers to itself.

4.2.2.9 Time to Live: RFC 791 Section 3.2

   Time to Live (TTL) handling for packets originated or received by the
   router is governed by [INTRO:2]; this section changes none of its
   stipulations.  However, since the remainder of the IP Protocol
   section of [INTRO:2] is rewritten, this section is as well.

   Note in particular that a router MUST NOT check the TTL of a packet
   except when forwarding it.

   A router MUST NOT originate or forward a datagram with a Time-to-Live
   (TTL) value of zero.

   A router MUST NOT discard a datagram just because it was received
   with TTL equal to zero or one; if it is to the router and otherwise
   valid, the router MUST attempt to receive it.

   On messages the router originates, the IP layer MUST provide a means
   for the transport layer to set the TTL field of every datagram that
   is sent.  When a fixed TTL value is used, it MUST be configurable.
   The number SHOULD exceed the typical internet diameter, and current
   wisdom suggests that it should exceed twice the internet diameter to
   allow for growth.  Current suggested values are normally posted in
   the Assigned Numbers RFC.  The TTL field has two functions: limit the
   lifetime of TCP segments (see RFC 793 [TCP:1], p. 28), and terminate
   Internet routing loops.  Although TTL is a time in seconds, it also
   has some attributes of a hop-count, since each router is required to
   reduce the TTL field by at least one.

   TTL expiration is intended to cause datagrams to be discarded by
   routers, but not by the destination host.  Hosts that act as routers
   by forwarding datagrams must therefore follow the router's rules for
   TTL.

   A higher-layer protocol may want to set the TTL in order to implement
   an "expanding scope" search for some Internet resource.  This is used
   by some diagnostic tools, and is expected to be useful for locating
   the "nearest" server of a given class using IP multicasting, for
   example.  A particular transport protocol may also want to specify
   its own TTL bound on maximum datagram lifetime.

   A fixed default value must be at least big enough for the Internet
   "diameter," i.e., the longest possible path.  A reasonable value is



Baker                       Standards Track                    [Page 46]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   about twice the diameter, to allow for continued Internet growth.  As
   of this writing, messages crossing the United States frequently
   traverse 15 to 20 routers; this argues for a default TTL value in
   excess of 40, and 64 is a common value.

4.2.2.10 Multi-subnet Broadcasts: RFC 922

   All-subnets broadcasts (called multi-subnet broadcasts in
   [INTERNET:3]) have been deprecated.  See Section [5.3.5.3].

4.2.2.11 Addressing: RFC 791 Section 3.2

   As noted in 2.2.5.1, there are now five classes of IP addresses:
   Class A through Class E.  Class D addresses are used for IP
   multicasting [INTERNET:4], while Class E addresses are reserved for
   experimental use.  The distinction between Class A, B, and C
   addresses is no longer important; they are used as generalized
   unicast network prefixes with only historical interest in their
   class.

   An IP multicast address is a 28-bit logical address that stands for a
   group of hosts, and may be either permanent or transient.  Permanent
   multicast addresses are allocated by the Internet Assigned Number
   Authority [INTRO:7], while transient addresses may be allocated
   dynamically to transient groups.  Group membership is determined
   dynamically using IGMP [INTERNET:4].

   We now summarize the important special cases for general purpose
   unicast IP addresses, using the following notation for an IP address:

    { ,  }

   and the notation -1 for a field that contains all 1 bits and the
   notation 0 for a field that contains all 0 bits.

   (a) { 0, 0 }

        This host on this network.  It MUST NOT be used as a source
        address by routers, except the router MAY use this as a source
        address as part of an initialization procedure (e.g., if the
        router is using BOOTP to load its configuration information).

        Incoming datagrams with a source address of { 0, 0 } which are
        received for local delivery (see Section [5.2.3]), MUST be
        accepted if the router implements the associated protocol and
        that protocol clearly defines appropriate action to be taken.
        Otherwise, a router MUST silently discard any locally-delivered
        datagram whose source address is { 0, 0 }.



Baker                       Standards Track                    [Page 47]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   DISCUSSION
      Some protocols define specific actions to take in response to a
      received datagram whose source address is { 0, 0 }.  Two examples
      are BOOTP and ICMP Mask Request.  The proper operation of these
      protocols often depends on the ability to receive datagrams whose
      source address is { 0, 0 }.  For most protocols, however, it is
      best to ignore datagrams having a source address of { 0, 0 } since
      they were probably generated by a misconfigured host or router.
      Thus, if a router knows how to deal with a given datagram having a
      { 0, 0 } source address, the router MUST accept it.  Otherwise,
      the router MUST discard it.

   See also Section [4.2.3.1] for a non-standard use of { 0, 0 }.

   (b) { 0,  }

         Specified host on this network.  It MUST NOT be sent by routers
         except that the router MAY use this as a source address as part
         of an initialization procedure by which the it learns its own
         IP address.

   (c) { -1, -1 }

         Limited broadcast.  It MUST NOT be used as a source address.

         A datagram with this destination address will be received by
         every host and router on the connected physical network, but
         will not be forwarded outside that network.

   (d) { , -1 }

         Directed Broadcast - a broadcast directed to the specified
         network prefix.  It MUST NOT be used as a source address.  A
         router MAY originate Network Directed Broadcast packets.  A
         router MUST receive Network Directed Broadcast packets; however
         a router MAY have a configuration option to prevent reception
         of these packets.  Such an option MUST default to allowing
         reception.

    (e) { 127,  }

         Internal host loopback address.  Addresses of this form MUST
         NOT appear outside a host.

    The  is administratively assigned so that its value
    will be unique in the routing domain to which the device is
    connected.




Baker                       Standards Track                    [Page 48]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


    IP addresses are not permitted to have the value 0 or -1 for the
     or  fields except in the special cases
    listed above.  This implies that each of these fields will be at
    least two bits long.

   DISCUSSION
      Previous versions of this document also noted that subnet numbers
      must be neither 0 nor -1, and must be at least two bits in length.
      In a CIDR world, the subnet number is clearly an extension of the
      network prefix and cannot be interpreted without the remainder of
      the prefix.  This restriction of subnet numbers is therefore
      meaningless in view of CIDR and may be safely ignored.

   For further discussion of broadcast addresses, see Section [4.2.3.1].

   When a router originates any datagram, the IP source address MUST be
   one of its own IP addresses (but not a broadcast or multicast
   address).  The only exception is during initialization.

   For most purposes, a datagram addressed to a broadcast or multicast
   destination is processed as if it had been addressed to one of the
   router's IP addresses; that is to say:

   o A router MUST receive and process normally any packets with a
      broadcast destination address.

   o A router MUST receive and process normally any packets sent to a
      multicast destination address that the router has asked to
      receive.

   The term specific-destination address means the equivalent local IP
   address of the host.  The specific-destination address is defined to
   be the destination address in the IP header unless the header
   contains a broadcast or multicast address, in which case the
   specific-destination is an IP address assigned to the physical
   interface on which the datagram arrived.

   A router MUST silently discard any received datagram containing an IP
   source address that is invalid by the rules of this section.  This
   validation could be done either by the IP layer or (when appropriate)
   by each protocol in the transport layer.  As with any datagram a
   router discards, the datagram discard SHOULD be counted.

   DISCUSSION
      A misaddressed datagram might be caused by a Link Layer broadcast
      of a unicast datagram or by another router or host that is
      confused or misconfigured.




Baker                       Standards Track                    [Page 49]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


4.2.3 SPECIFIC ISSUES

4.2.3.1 IP Broadcast Addresses

   For historical reasons, there are a number of IP addresses (some
   standard and some not) which are used to indicate that an IP packet
   is an IP broadcast.  A router

   (1) MUST treat as IP broadcasts packets addressed to 255.255.255.255
        or { , -1 }.

   (2) SHOULD silently discard on receipt (i.e., do not even deliver to
        applications in the router) any packet addressed to 0.0.0.0 or {
        , 0 }.  If these packets are not silently
        discarded, they MUST be treated as IP broadcasts (see Section
        [5.3.5]).  There MAY be a configuration option to allow receipt
        of these packets.  This option SHOULD default to discarding
        them.

   (3) SHOULD (by default) use the limited broadcast address
        (255.255.255.255) when originating an IP broadcast destined for
        a connected (sub)network (except when sending an ICMP Address
        Mask Reply, as discussed in Section [4.3.3.9]).  A router MUST
        receive limited broadcasts.

   (4) SHOULD NOT originate datagrams addressed to 0.0.0.0 or {
        , 0 }.  There MAY be a configuration option to
        allow generation of these packets (instead of using the relevant
        1s format broadcast).  This option SHOULD default to not
        generating them.

   DISCUSSION
      In the second bullet, the router obviously cannot recognize
      addresses of the form { , 0 } if the router has no
      interface to that network prefix.  In that case, the rules of the
      second bullet do not apply because, from the point of view of the
      router, the packet is not an IP broadcast packet.

4.2.3.2 IP Multicasting

   An IP router SHOULD satisfy the Host Requirements with respect to IP
   multicasting, as specified in [INTRO:2].  An IP router SHOULD support
   local IP multicasting on all connected networks.  When a mapping from
   IP multicast addresses to link-layer addresses has been specified
   (see the various IP-over-xxx specifications), it SHOULD use that
   mapping, and MAY be configurable to use the link layer broadcast
   instead.  On point-to-point links and all other interfaces,
   multicasts are encapsulated as link layer broadcasts.  Support for



Baker                       Standards Track                    [Page 50]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   local IP multicasting includes originating multicast datagrams,
   joining multicast groups and receiving multicast datagrams, and
   leaving multicast groups.  This implies support for all of
   [INTERNET:4] including IGMP (see Section [4.4]).

   DISCUSSION
      Although [INTERNET:4] is entitled Host Extensions for IP
      Multicasting, it applies to all IP systems, both hosts and
      routers.  In particular, since routers may join multicast groups,
      it is correct for them to perform the host part of IGMP, reporting
      their group memberships to any multicast routers that may be
      present on their attached networks (whether or not they themselves
      are multicast routers).

      Some router protocols may specifically require support for IP
      multicasting (e.g., OSPF [ROUTE:1]), or may recommend it (e.g.,
      ICMP Router Discovery [INTERNET:13]).

4.2.3.3 Path MTU Discovery

   To eliminate fragmentation or minimize it, it is desirable to know
   what is the path MTU along the path from the source to destination.
   The path MTU is the minimum of the MTUs of each hop in the path.
   [INTERNET:14] describes a technique for dynamically discovering the
   maximum transmission unit (MTU) of an arbitrary internet path.  For a
   path that passes through a router that does not support
   [INTERNET:14], this technique might not discover the correct Path
   MTU, but it will always choose a Path MTU as accurate as, and in many
   cases more accurate than, the Path MTU that would be chosen by older
   techniques or the current practice.

   When a router is originating an IP datagram, it SHOULD use the scheme
   described in [INTERNET:14] to limit the datagram's size.  If the
   router's route to the datagram's destination was learned from a
   routing protocol that provides Path MTU information, the scheme
   described in [INTERNET:14] is still used, but the Path MTU
   information from the routing protocol SHOULD be used as the initial
   guess as to the Path MTU and also as an upper bound on the Path MTU.

4.2.3.4 Subnetting

   Under certain circumstances, it may be desirable to support subnets
   of a particular network being interconnected only through a path that
   is not part of the subnetted network.  This is known as discontiguous
   subnetwork support.

   Routers MUST support discontiguous subnetworks.




Baker                       Standards Track                    [Page 51]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   IMPLEMENTATION
      In classical IP networks, this was very difficult to achieve; in
      CIDR networks, it is a natural by-product.  Therefore, a router
      SHOULD NOT make assumptions about subnet architecture, but SHOULD
      treat each route as a generalized network prefix.

   DISCUSSION The Internet has been growing at a tremendous rate of
      late.  This has been placing severe strains on the IP addressing
      technology.  A major factor in this strain is the strict IP
      Address class boundaries.  These make it difficult to efficiently
      size network prefixes to their networks and aggregate several
      network prefixes into a single route advertisement.  By
      eliminating the strict class boundaries of the IP address and
      treating each route as a generalized network prefix, these strains
      may be greatly reduced.

      The technology for currently doing this is Classless Inter Domain
      Routing (CIDR) [INTERNET:15].

   For similar reasons, an address block associated with a given network
   prefix could be subdivided into subblocks of different sizes, so that
   the network prefixes associated with the subblocks would have
   different length.  For example, within a block whose network prefix
   is 8 bits long, one subblock may have a 16 bit network prefix,
   another may have an 18 bit network prefix, and a third a 14 bit
   network prefix.

   Routers MUST support variable length network prefixes in both their
   interface configurations and their routing databases.

4.3 INTERNET CONTROL MESSAGE PROTOCOL - ICMP

4.3.1 INTRODUCTION

   ICMP is an auxiliary protocol, which provides routing, diagnostic and
   error functionality for IP.  It is described in [INTERNET:8].  A
   router MUST support ICMP.

   ICMP messages are grouped in two classes that are discussed in the
   following sections:

   ICMP error messages:

   Destination Unreachable     Section 4.3.3.1
   Redirect                    Section 4.3.3.2
   Source Quench               Section 4.3.3.3
   Time Exceeded               Section 4.3.3.4
   Parameter Problem           Section 4.3.3.5



Baker                       Standards Track                    [Page 52]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   ICMP query messages:
   Echo                        Section 4.3.3.6
   Information                 Section 4.3.3.7
   Timestamp                   Section 4.3.3.8
   Address Mask                Section 4.3.3.9
   Router Discovery            Section 4.3.3.10


   General ICMP requirements and discussion are in the next section.

4.3.2 GENERAL ISSUES

4.3.2.1 Unknown Message Types

   If an ICMP message of unknown type is received, it MUST be passed to
   the ICMP user interface (if the router has one) or silently discarded
   (if the router does not have one).

4.3.2.2 ICMP Message TTL

   When originating an ICMP message, the router MUST initialize the TTL.
   The TTL for ICMP responses must not be taken from the packet that
   triggered the response.

4.3.2.3 Original Message Header

   Historically, every ICMP error message has included the Internet
   header and at least the first 8 data bytes of the datagram that
   triggered the error.  This is no longer adequate, due to the use of
   IP-in-IP tunneling and other technologies.  Therefore, the ICMP
   datagram SHOULD contain as much of the original datagram as possible
   without the length of the ICMP datagram exceeding 576 bytes.  The
   returned IP header (and user data) MUST be identical to that which
   was received, except that the router is not required to undo any
   modifications to the IP header that are normally performed in
   forwarding that were performed before the error was detected (e.g.,
   decrementing the TTL, or updating options).  Note that the
   requirements of Section [4.3.3.5] supersede this requirement in some
   cases (i.e., for a Parameter Problem message, if the problem is in a
   modified field, the router must undo the modification).  See Section
   [4.3.3.5]).

4.3.2.4 ICMP Message Source Address

   Except where this document specifies otherwise, the IP source address
   in an ICMP message originated by the router MUST be one of the IP
   addresses associated with the physical interface over which the ICMP
   message is transmitted.  If the interface has no IP addresses



Baker                       Standards Track                    [Page 53]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   associated with it, the router's router-id (see Section [5.2.5]) is
   used instead.

4.3.2.5 TOS and Precedence

   ICMP error messages SHOULD have their TOS bits set to the same value
   as the TOS bits in the packet that provoked the sending of the ICMP
   error message, unless setting them to that value would cause the ICMP
   error message to be immediately discarded because it could not be
   routed to its destination.  Otherwise, ICMP error messages MUST be
   sent with a normal (i.e., zero) TOS.  An ICMP reply message SHOULD
   have its TOS bits set to the same value as the TOS bits in the ICMP
   request that provoked the reply.

   ICMP Source Quench error messages, if sent at all, MUST have their IP
   Precedence field set to the same value as the IP Precedence field in
   the packet that provoked the sending of the ICMP Source Quench
   message.  All other ICMP error messages (Destination Unreachable,
   Redirect, Time Exceeded, and Parameter Problem) SHOULD have their
   precedence value set to 6 (INTERNETWORK CONTROL) or 7 (NETWORK
   CONTROL).  The IP Precedence value for these error messages MAY be
   settable.

   An ICMP reply message MUST have its IP Precedence field set to the
   same value as the IP Precedence field in the ICMP request that
   provoked the reply.

4.3.2.6 Source Route

   If the packet which provokes the sending of an ICMP error message
   contains a source route option, the ICMP error message SHOULD also
   contain a source route option of the same type (strict or loose),
   created by reversing the portion before the pointer of the route
   recorded in the source route option of the original packet UNLESS the
   ICMP error message is an ICMP Parameter Problem complaining about a
   source route option in the original packet, or unless the router is
   aware of policy that would prevent the delivery of the ICMP error
   message.

   DISCUSSION
      In environments which use the U.S.  Department of Defense security
      option (defined in [INTERNET:5]), ICMP messages may need to
      include a security option.  Detailed information on this topic
      should be available from the Defense Communications Agency.







Baker                       Standards Track                    [Page 54]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


4.3.2.7 When Not to Send ICMP Errors

   An ICMP error message MUST NOT be sent as the result of receiving:

   o An ICMP error message, or

   o A packet which fails the IP header validation tests described in
      Section [5.2.2] (except where that section specifically permits
      the sending of an ICMP error message), or

   o A packet destined to an IP broadcast or IP multicast address, or

   o A packet sent as a Link Layer broadcast or multicast, or

   o A packet whose source address has a network prefix of zero or is an
      invalid source address (as defined in Section [5.3.7]), or

   o Any fragment of a datagram other then the first fragment (i.e., a
      packet for which the fragment offset in the IP header is nonzero).

   Furthermore, an ICMP error message MUST NOT be sent in any case where
   this memo states that a packet is to be silently discarded.

   NOTE: THESE RESTRICTIONS TAKE PRECEDENCE OVER ANY REQUIREMENT
   ELSEWHERE IN THIS DOCUMENT FOR SENDING ICMP ERROR MESSAGES.

   DISCUSSION
      These rules aim to prevent the broadcast storms that have resulted
      from routers or hosts returning ICMP error messages in response to
      broadcast packets.  For example, a broadcast UDP packet to a non-
      existent port could trigger a flood of ICMP Destination
      Unreachable datagrams from all devices that do not have a client
      for that destination port.  On a large Ethernet, the resulting
      collisions can render the network useless for a second or more.

      Every packet that is broadcast on the connected network should
      have a valid IP broadcast address as its IP destination (see
      Section [5.3.4] and [INTRO:2]).  However, some devices violate
      this rule.  To be certain to detect broadcast packets, therefore,
      routers are required to check for a link-layer broadcast as well
      as an IP-layer address.

   IMPLEMENTATION+ This requires that the link layer inform the IP layer
      when a link-layer broadcast packet has been received; see Section
      [3.1].






Baker                       Standards Track                    [Page 55]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


4.3.2.8 Rate Limiting

   A router which sends ICMP Source Quench messages MUST be able to
   limit the rate at which the messages can be generated.  A router
   SHOULD also be able to limit the rate at which it sends other sorts
   of ICMP error messages (Destination Unreachable, Redirect, Time
   Exceeded, Parameter Problem).  The rate limit parameters SHOULD be
   settable as part of the configuration of the router.  How the limits
   are applied (e.g., per router or per interface) is left to the
   implementor's discretion.

   DISCUSSION
      Two problems for a router sending ICMP error message are:
      (1) The consumption of bandwidth on the reverse path, and
      (2) The use of router resources (e.g., memory, CPU time)

      To help solve these problems a router can limit the frequency with
      which it generates ICMP error messages.  For similar reasons, a
      router may limit the frequency at which some other sorts of
      messages, such as ICMP Echo Replies, are generated.

   IMPLEMENTATION
      Various mechanisms have been used or proposed for limiting the
      rate at which ICMP messages are sent:

      (1) Count-based - for example, send an ICMP error message for
           every N dropped packets overall or per given source host.
           This mechanism might be appropriate for ICMP Source Quench,
           if used, but probably not for other types of ICMP messages.

      (2) Timer-based - for example, send an ICMP error message to a
           given source host or overall at most once per T milliseconds.

      (3) Bandwidth-based - for example, limit the rate at which ICMP
           messages are sent over a particular interface to some
           fraction of the attached network's bandwidth.

4.3.3 SPECIFIC ISSUES

4.3.3.1 Destination Unreachable

   If a router cannot forward a packet because it has no routes at all
   (including no default route) to the destination specified in the
   packet, then the router MUST generate a Destination Unreachable, Code
   0 (Network Unreachable) ICMP message.  If the router does have routes
   to the destination network specified in the packet but the TOS
   specified for the routes is neither the default TOS (0000) nor the
   TOS of the packet that the router is attempting to route, then the



Baker                       Standards Track                    [Page 56]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   router MUST generate a Destination Unreachable, Code 11 (Network
   Unreachable for TOS) ICMP message.

   If a packet is to be forwarded to a host on a network that is
   directly connected to the router (i.e., the router is the last-hop
   router) and the router has ascertained that there is no path to the
   destination host then the router MUST generate a Destination
   Unreachable, Code 1 (Host Unreachable) ICMP message.  If a packet is
   to be forwarded to a host that is on a network that is directly
   connected to the router and the router cannot forward the packet
   because no route to the destination has a TOS that is either equal to
   the TOS requested in the packet or is the default TOS (0000) then the
   router MUST generate a Destination Unreachable, Code 12 (Host
   Unreachable for TOS) ICMP message.

   DISCUSSION
      The intent is that a router generates the "generic" host/network
      unreachable if it has no path at all (including default routes) to
      the destination.  If the router has one or more paths to the
      destination, but none of those paths have an acceptable TOS, then
      the router generates the "unreachable for TOS" message.

4.3.3.2 Redirect

   The ICMP Redirect message is generated to inform a local host that it
   should use a different next hop router for certain traffic.

   Contrary to [INTRO:2], a router MAY ignore ICMP Redirects when
   choosing a path for a packet originated by the router if the router
   is running a routing protocol or if forwarding is enabled on the
   router and on the interface over which the packet is being sent.

4.3.3.3 Source Quench

   A router SHOULD NOT originate ICMP Source Quench messages.  As
   specified in Section [4.3.2], a router that does originate Source
   Quench messages MUST be able to limit the rate at which they are
   generated.

   DISCUSSION
      Research seems to suggest that Source Quench consumes network
      bandwidth but is an ineffective (and unfair) antidote to
      congestion.  See, for example, [INTERNET:9] and [INTERNET:10].
      Section [5.3.6] discusses the current thinking on how routers
      ought to deal with overload and network congestion.

   A router MAY ignore any ICMP Source Quench messages it receives.




Baker                       Standards Track                    [Page 57]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   DISCUSSION
      A router itself may receive a Source Quench as the result of
      originating a packet sent to another router or host.  Such
      datagrams might be, e.g., an EGP update sent to another router, or
      a telnet stream sent to a host.  A mechanism has been proposed
      ([INTERNET:11], [INTERNET:12]) to make the IP layer respond
      directly to Source Quench by controlling the rate at which packets
      are sent, however, this proposal is currently experimental and not
      currently recommended.

4.3.3.4 Time Exceeded

   When a router is forwarding a packet and the TTL field of the packet
   is reduced to 0, the requirements of section [5.2.3.8] apply.

   When the router is reassembling a packet that is destined for the
   router, it is acting as an Internet host.  [INTRO:2]'s reassembly
   requirements therefore apply.

   When the router receives (i.e., is destined for the router) a Time
   Exceeded message, it MUST comply with [INTRO:2].

4.3.3.5 Parameter Problem

   A router MUST generate a Parameter Problem message for any error not
   specifically covered by another ICMP message.  The IP header field or
   IP option including the byte indicated by the pointer field MUST be
   included unchanged in the IP header returned with this ICMP message.
   Section [4.3.2] defines an exception to this requirement.

   A new variant of the Parameter Problem message was defined in
   [INTRO:2]:
        Code 1 = required option is missing.

   DISCUSSION
      This variant is currently in use in the military community for a
      missing security option.

4.3.3.6 Echo Request/Reply

   A router MUST implement an ICMP Echo server function that receives
   Echo Requests sent to the router, and sends corresponding Echo
   Replies.  A router MUST be prepared to receive, reassemble and echo
   an ICMP Echo Request datagram at least as the maximum of 576 and the
   MTUs of all the connected networks.

   The Echo server function MAY choose not to respond to ICMP echo
   requests addressed to IP broadcast or IP multicast addresses.



Baker                       Standards Track                    [Page 58]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   A router SHOULD have a configuration option that, if enabled, causes
   the router to silently ignore all ICMP echo requests; if provided,
   this option MUST default to allowing responses.

   DISCUSSION
      The neutral provision about responding to broadcast and multicast
      Echo Requests derives from [INTRO:2]'s "Echo Request/Reply"
      section.

   As stated in Section [10.3.3], a router MUST also implement a
   user/application-layer interface for sending an Echo Request and
   receiving an Echo Reply, for diagnostic purposes.  All ICMP Echo
   Reply messages MUST be passed to this interface.

   The IP source address in an ICMP Echo Reply MUST be the same as the
   specific-destination address of the corresponding ICMP Echo Request
   message.

   Data received in an ICMP Echo Request MUST be entirely included in
   the resulting Echo Reply.

   If a Record Route and/or Timestamp option is received in an ICMP Echo
   Request, this option (these options) SHOULD be updated to include the
   current router and included in the IP header of the Echo Reply
   message, without truncation.  Thus, the recorded route will be for
   the entire round trip.

   If a Source Route option is received in an ICMP Echo Request, the
   return route MUST be reversed and used as a Source Route option for
   the Echo Reply message, unless the router is aware of policy that
   would prevent the delivery of the message.

4.3.3.7 Information Request/Reply

   A router SHOULD NOT originate or respond to these messages.

   DISCUSSION
      The Information Request/Reply pair was intended to support self-
      configuring systems such as diskless workstations, to allow them
      to discover their IP network prefixes at boot time.  However,
      these messages are now obsolete.  The RARP and BOOTP protocols
      provide better mechanisms for a host to discover its own IP
      address.

4.3.3.8 Timestamp and Timestamp Reply

   A router MAY implement Timestamp and Timestamp Reply.  If they are
   implemented then:



Baker                       Standards Track                    [Page 59]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   o The ICMP Timestamp server function MUST return a Timestamp Reply to
      every Timestamp message that is received.  It SHOULD be designed
      for minimum variability in delay.

   o An ICMP Timestamp Request message to an IP broadcast or IP
      multicast address MAY be silently discarded.

   o The IP source address in an ICMP Timestamp Reply MUST be the same
      as the specific-destination address of the corresponding Timestamp
      Request message.

   o If a Source Route option is received in an ICMP Timestamp Request,
      the return route MUST be reversed and used as a Source Route
      option for the Timestamp Reply message, unless the router is aware
      of policy that would prevent the delivery of the message.

   o If a Record Route and/or Timestamp option is received in a
      Timestamp Request, this (these) option(s) SHOULD be updated to
      include the current router and included in the IP header of the
      Timestamp Reply message.

   o If the router provides an application-layer interface for sending
      Timestamp Request messages then incoming Timestamp Reply messages
      MUST be passed up to the ICMP user interface.

   The preferred form for a timestamp value (the standard value) is
   milliseconds since midnight, Universal Time.  However, it may be
   difficult to provide this value with millisecond resolution.  For
   example, many systems use clocks that update only at line frequency,
   50 or 60 times per second.  Therefore, some latitude is allowed in a
   standard value:

   (a) A standard value MUST be updated at least 16 times per second
        (i.e., at most the six low-order bits of the value may be
        undefined).

   (b) The accuracy of a standard value MUST approximate that of
        operator-set CPU clocks, i.e., correct within a few minutes.

   IMPLEMENTATION
      To meet the second condition, a router may need to query some time
      server when the router is booted or restarted.  It is recommended
      that the UDP Time Server Protocol be used for this purpose.  A
      more advanced implementation would use the Network Time Protocol
      (NTP) to achieve nearly millisecond clock synchronization;
      however, this is not required.





Baker                       Standards Track                    [Page 60]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


4.3.3.9 Address Mask Request/Reply

   A router MUST implement support for receiving ICMP Address Mask
   Request messages and responding with ICMP Address Mask Reply
   messages.  These messages are defined in [INTERNET:2].

   A router SHOULD have a configuration option for each logical
   interface specifying whether the router is allowed to answer Address
   Mask Requests for that interface; this option MUST default to
   allowing responses.  A router MUST NOT respond to an Address Mask
   Request before the router knows the correct address mask.

   A router MUST NOT respond to an Address Mask Request that has a
   source address of 0.0.0.0 and which arrives on a physical interface
   that has associated with it multiple logical interfaces and the
   address masks for those interfaces are not all the same.

   A router SHOULD examine all ICMP Address Mask Replies that it
   receives to determine whether the information it contains matches the
   router's knowledge of the address mask.  If the ICMP Address Mask
   Reply appears to be in error, the router SHOULD log the address mask
   and the sender's IP address.  A router MUST NOT use the contents of
   an ICMP Address Mask Reply to determine the correct address mask.

   Because hosts may not be able to learn the address mask if a router
   is down when the host boots up, a router MAY broadcast a gratuitous
   ICMP Address Mask Reply on each of its logical interfaces after it
   has configured its own address masks.  However, this feature can be
   dangerous in environments that use variable length address masks.
   Therefore, if this feature is implemented, gratuitous Address Mask
   Replies MUST NOT be broadcast over any logical interface(s) which
   either:

   o Are not configured to send gratuitous Address Mask Replies.  Each
      logical interface MUST have a configuration parameter controlling
      this, and that parameter MUST default to not sending the
      gratuitous Address Mask Replies.

   o Share subsuming (but not identical) network prefixes and physical
      interface.

   The { , -1 } form of the IP broadcast address MUST be
   used for broadcast Address Mask Replies.

   DISCUSSION
      The ability to disable sending Address Mask Replies by routers is
      required at a few sites that intentionally lie to their hosts
      about the address mask.  The need for this is expected to go away



Baker                       Standards Track                    [Page 61]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


      as more and more hosts become compliant with the Host Requirements
      standards.

      The reason for both the second bullet above and the requirement
      about which IP broadcast address to use is to prevent problems
      when multiple IP network prefixes are in use on the same physical
      network.

4.3.3.10 Router Advertisement and Solicitations

   An IP router MUST support the router part of the ICMP Router
   Discovery Protocol [INTERNET:13] on all connected networks on which
   the router supports either IP multicast or IP broadcast addressing.
   The implementation MUST include all the configuration variables
   specified for routers, with the specified defaults.

   DISCUSSION
      Routers are not required to implement the host part of the ICMP
      Router Discovery Protocol, but might find it useful for operation
      while IP forwarding is disabled (i.e., when operating as a host).

   DISCUSSION We note that it is quite common for hosts to use RIP
      Version 1 as the router discovery protocol.  Such hosts listen to
      RIP traffic and use and use information extracted from that
      traffic to discover routers and to make decisions as to which
      router to use as a first-hop router for a given destination.
      While this behavior is discouraged, it is still common and
      implementors should be aware of it.

4.4 INTERNET GROUP MANAGEMENT PROTOCOL - IGMP

   IGMP [INTERNET:4] is a protocol used between hosts and multicast
   routers on a single physical network to establish hosts' membership
   in particular multicast groups.  Multicast routers use this
   information, in conjunction with a multicast routing protocol, to
   support IP multicast forwarding across the Internet.

   A router SHOULD implement the host part of IGMP.













Baker                       Standards Track                    [Page 62]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


5. INTERNET LAYER - FORWARDING

5.1 INTRODUCTION

   This section describes the process of forwarding packets.

5.2 FORWARDING WALK-THROUGH

   There is no separate specification of the forwarding function in IP.
   Instead, forwarding is covered by the protocol specifications for the
   internet layer protocols ([INTERNET:1], [INTERNET:2], [INTERNET:3],
   [INTERNET:8], and [ROUTE:11]).

5.2.1 Forwarding Algorithm

   Since none of the primary protocol documents describe the forwarding
   algorithm in any detail, we present it here.  This is just a general
   outline, and omits important details, such as handling of congestion,
   that are dealt with in later sections.

   It is not required that an implementation follow exactly the
   algorithms given in sections [5.2.1.1], [5.2.1.2], and [5.2.1.3].
   Much of the challenge of writing router software is to maximize the
   rate at which the router can forward packets while still achieving
   the same effect of the algorithm.  Details of how to do that are
   beyond the scope of this document, in part because they are heavily
   dependent on the architecture of the router.  Instead, we merely
   point out the order dependencies among the steps:

   (1) A router MUST verify the IP header, as described in section
        [5.2.2], before performing any actions based on the contents of
        the header.  This allows the router to detect and discard bad
        packets before the expenditure of other resources.

   (2) Processing of certain IP options requires that the router insert
        its IP address into the option.  As noted in Section [5.2.4],
        the address inserted MUST be the address of the logical
        interface on which the packet is sent or the router's router-id
        if the packet is sent over an unnumbered interface.  Thus,
        processing of these options cannot be completed until after the
        output interface is chosen.

   (3) The router cannot check and decrement the TTL before checking
        whether the packet should be delivered to the router itself, for
        reasons mentioned in Section [4.2.2.9].

   (4) More generally, when a packet is delivered locally to the router,
        its IP header MUST NOT be modified in any way (except that a



Baker                       Standards Track                    [Page 63]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


        router may be required to insert a timestamp into any Timestamp
        options in the IP header).  Thus, before the router determines
        whether the packet is to be delivered locally to the router, it
        cannot update the IP header in any way that it is not prepared
        to undo.

5.2.1.1 General

   This section covers the general forwarding algorithm.  This algorithm
   applies to all forms of packets to be forwarded: unicast, multicast,
   and broadcast.


   (1) The router receives the IP packet (plus additional information
        about it, as described in Section [3.1]) from the Link Layer.

   (2) The router validates the IP header, as described in Section
        [5.2.2].  Note that IP reassembly is not done, except on IP
        fragments to be queued for local delivery in step (4).

   (3) The router performs most of the processing of any IP options.  As
        described in Section [5.2.4], some IP options require additional
        processing after the routing decision has been made.

   (4) The router examines the destination IP address of the IP
        datagram, as described in Section [5.2.3], to determine how it
        should continue to process the IP datagram.  There are three
        possibilities:

        o The IP datagram is destined for the router, and should be
           queued for local delivery, doing reassembly if needed.

        o The IP datagram is not destined for the router, and should be
           queued for forwarding.

        o The IP datagram should be queued for forwarding, but (a copy)
           must also be queued for local delivery.

5.2.1.2 Unicast

   Since the local delivery case is well covered by [INTRO:2], the
   following assumes that the IP datagram was queued for forwarding.  If
   the destination is an IP unicast address:

   (5) The forwarder determines the next hop IP address for the packet,
        usually by looking up the packet's destination in the router's
        routing table.  This procedure is described in more detail in
        Section [5.2.4].  This procedure also decides which network



Baker                       Standards Track                    [Page 64]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


        interface should be used to send the packet.

   (6) The forwarder verifies that forwarding the packet is permitted.
        The source and destination addresses should be valid, as
        described in Section [5.3.7] and Section [5.3.4] If the router
        supports administrative constraints on forwarding, such as those
        described in Section [5.3.9], those constraints must be
        satisfied.

   (7) The forwarder decrements (by at least one) and checks the
        packet's TTL, as described in Section [5.3.1].

   (8) The forwarder performs any IP option processing that could not be
        completed in step 3.

   (9) The forwarder performs any necessary IP fragmentation, as
        described in Section [4.2.2.7].  Since this step occurs after
        outbound interface selection (step 5), all fragments of the same
        datagram will be transmitted out the same interface.

   (10) The forwarder determines the Link Layer address of the packet's
        next hop.  The mechanisms for doing this are Link Layer-
        dependent (see chapter 3).

   (11) The forwarder encapsulates the IP datagram (or each of the
        fragments thereof) in an appropriate Link Layer frame and queues
        it for output on the interface selected in step 5.

   (12) The forwarder sends an ICMP redirect if necessary, as described
        in Section [4.3.3.2].

5.2.1.3 Multicast

   If the destination is an IP multicast, the following steps are taken.

   Note that the main differences between the forwarding of IP unicasts
   and the forwarding of IP multicasts are

   o IP multicasts are usually forwarded based on both the datagram's
      source and destination IP addresses,

   o IP multicast uses an expanding ring search,

   o IP multicasts are forwarded as Link Level multicasts, and

   o ICMP errors are never sent in response to IP multicast datagrams.





Baker                       Standards Track                    [Page 65]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   Note that the forwarding of IP multicasts is still somewhat
   experimental.  As a result, the algorithm presented below is not
   mandatory, and is provided as an example only.

   (5a) Based on the IP source and destination addresses found in the
        datagram header, the router determines whether the datagram has
        been received on the proper interface for forwarding.  If not,
        the datagram is dropped silently.  The method for determining
        the proper receiving interface depends on the multicast routing
        algorithm(s) in use.  In one of the simplest algorithms, reverse
        path forwarding (RPF), the proper interface is the one that
        would be used to forward unicasts back to the datagram source.

   (6a) Based on the IP source and destination addresses found in the
        datagram header, the router determines the datagram's outgoing
        interfaces.  To implement IP multicast's expanding ring search
        (see [INTERNET:4]) a minimum TTL value is specified for each
        outgoing interface.  A copy of the multicast datagram is
        forwarded out each outgoing interface whose minimum TTL value is
        less than or equal to the TTL value in the datagram header, by
        separately applying the remaining steps on each such interface.

   (7a) The router decrements the packet's TTL by one.

   (8a) The forwarder performs any IP option processing that could not
        be completed in step (3).

   (9a) The forwarder performs any necessary IP fragmentation, as
        described in Section [4.2.2.7].

   (10a) The forwarder determines the Link Layer address to use in the
        Link Level encapsulation.  The mechanisms for doing this are
        Link Layer-dependent.  On LANs a Link Level multicast or
        broadcast is selected, as an algorithmic translation of the
        datagrams' IP multicast address.  See the various IP-over-xxx
        specifications for more details.

   (11a) The forwarder encapsulates the packet (or each of the fragments
        thereof) in an appropriate Link Layer frame and queues it for
        output on the appropriate interface.











Baker                       Standards Track                    [Page 66]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


5.2.2 IP Header Validation

   Before a router can process any IP packet, it MUST perform a the
   following basic validity checks on the packet's IP header to ensure
   that the header is meaningful.  If the packet fails any of the
   following tests, it MUST be silently discarded, and the error SHOULD
   be logged.

   (1) The packet length reported by the Link Layer must be large enough
        to hold the minimum length legal IP datagram (20 bytes).

   (2) The IP checksum must be correct.

   (3) The IP version number must be 4.  If the version number is not 4
        then the packet may be another version of IP, such as IPng or
        ST-II.

   (4) The IP header length field must be large enough to hold the
        minimum length legal IP datagram (20 bytes = 5 words).

   (5) The IP total length field must be large enough to hold the IP
        datagram header, whose length is specified in the IP header
        length field.

   A router MUST NOT have a configuration option that allows disabling
   any of these tests.

   If the packet passes the second and third tests, the IP header length
   field is at least 4, and both the IP total length field and the
   packet length reported by the Link Layer are at least 16 then,
   despite the above rule, the router MAY respond with an ICMP Parameter
   Problem message, whose pointer points at the IP header length field
   (if it failed the fourth test) or the IP total length field (if it
   failed the fifth test).  However, it still MUST discard the packet
   and still SHOULD log the error.

   These rules (and this entire document) apply only to version 4 of the
   Internet Protocol.  These rules should not be construed as
   prohibiting routers from supporting other versions of IP.
   Furthermore, if a router can truly classify a packet as being some
   other version of IP then it ought not treat that packet as an error
   packet within the context of this memo.

   IMPLEMENTATION
      It is desirable for purposes of error reporting, though not always
      entirely possible, to determine why a header was invalid.  There
      are four possible reasons:




Baker                       Standards Track                    [Page 67]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


      o The Link Layer truncated the IP header

      o The datagram is using a version of IP other than the standard
         one (version 4).

      o The IP header has been corrupted in transit.

      o The sender generated an illegal IP header.

      It is probably desirable to perform the checks in the order
      listed, since we believe that this ordering is most likely to
      correctly categorize the cause of the error.  For purposes of
      error reporting, it may also be desirable to check if a packet
      that fails these tests has an IP version number indicating IPng or
      ST-II; these should be handled according to their respective
      specifications.

   Additionally, the router SHOULD verify that the packet length
   reported by the Link Layer is at least as large as the IP total
   length recorded in the packet's IP header.  If it appears that the
   packet has been truncated, the packet MUST be discarded, the error
   SHOULD be logged, and the router SHOULD respond with an ICMP
   Parameter Problem message whose pointer points at the IP total length
   field.

   DISCUSSION
      Because any higher layer protocol that concerns itself with data
      corruption will detect truncation of the packet data when it
      reaches its final destination, it is not absolutely necessary for
      routers to perform the check suggested above to maintain protocol
      correctness.  However, by making this check a router can simplify
      considerably the task of determining which hop in the path is
      truncating the packets.  It will also reduce the expenditure of
      resources down-stream from the router in that down-stream systems
      will not need to deal with the packet.

   Finally, if the destination address in the IP header is not one of
   the addresses of the router, the router SHOULD verify that the packet
   does not contain a Strict Source and Record Route option.  If a
   packet fails this test (if it contains a strict source route option),
   the router SHOULD log the error and SHOULD respond with an ICMP
   Parameter Problem error with the pointer pointing at the offending
   packet's IP destination address.

   DISCUSSION
      Some people might suggest that the router should respond with a
      Bad Source Route message instead of a Parameter Problem message.
      However, when a packet fails this test, it usually indicates a



Baker                       Standards Track                    [Page 68]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


      protocol error by the previous hop router, whereas Bad Source
      Route would suggest that the source host had requested a
      nonexistent or broken path through the network.

5.2.3 Local Delivery Decision

   When a router receives an IP packet, it must decide whether the
   packet is addressed to the router (and should be delivered locally)
   or the packet is addressed to another system (and should be handled
   by the forwarder).  There is also a hybrid case, where certain IP
   broadcasts and IP multicasts are both delivered locally and
   forwarded.  A router MUST determine which of the these three cases
   applies using the following rules.


   o An unexpired source route option is one whose pointer value does
      not point past the last entry in the source route.  If the packet
      contains an unexpired source route option, the pointer in the
      option is advanced until either the pointer does point past the
      last address in the option or else the next address is not one of
      the router's own addresses.  In the latter (normal) case, the
      packet is forwarded (and not delivered locally) regardless of the
      rules below.

   o The packet is delivered locally and not considered for forwarding
      in the following cases:

      - The packet's destination address exactly matches one of the
         router's IP addresses,

      - The packet's destination address is a limited broadcast address
         ({-1, -1}), or

      - The packet's destination is an IP multicast address which is
         never forwarded (such as 224.0.0.1 or 224.0.0.2) and (at least)
         one of the logical interfaces associated with the physical
         interface on which the packet arrived is a member of the
         destination multicast group.

   o The packet is passed to the forwarder AND delivered locally in the
      following cases:

      - The packet's destination address is an IP broadcast address that
         addresses at least one of the router's logical interfaces but
         does not address any of the logical interfaces associated with
         the physical interface on which the packet arrived





Baker                       Standards Track                    [Page 69]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


      - The packet's destination is an IP multicast address which is
         permitted to be forwarded (unlike 224.0.0.1 and 224.0.0.2) and
         (at least) one of the logical interfaces associated with the
         physical interface on which the packet arrived is a member of
         the destination multicast group.

   o The packet is delivered locally if the packet's destination address
      is an IP broadcast address (other than a limited broadcast
      address) that addresses at least one of the logical interfaces
      associated with the physical interface on which the packet
      arrived.  The packet is ALSO passed to the forwarder unless the
      link on which the packet arrived uses an IP encapsulation that
      does not encapsulate broadcasts differently than unicasts (e.g.,
      by using different Link Layer destination addresses).

   o The packet is passed to the forwarder in all other cases.

   DISCUSSION
      The purpose of the requirement in the last sentence of the fourth
      bullet is to deal with a directed broadcast to another network
      prefix on the same physical cable.  Normally, this works as
      expected: the sender sends the broadcast to the router as a Link
      Layer unicast.  The router notes that it arrived as a unicast, and
      therefore must be destined for a different network prefix than the
      sender sent it on.  Therefore, the router can safely send it as a
      Link Layer broadcast out the same (physical) interface over which
      it arrived.  However, if the router can't tell whether the packet
      was received as a Link Layer unicast, the sentence ensures that
      the router does the safe but wrong thing rather than the unsafe
      but right thing.

   IMPLEMENTATION
      As described in Section [5.3.4], packets received as Link Layer
      broadcasts are generally not forwarded.  It may be advantageous to
      avoid passing to the forwarder packets it would later discard
      because of the rules in that section.

      Some Link Layers (either because of the hardware or because of
      special code in the drivers) can deliver to the router copies of
      all Link Layer broadcasts and multicasts it transmits.  Use of
      this feature can simplify the implementation of cases where a
      packet has to both be passed to the forwarder and delivered
      locally, since forwarding the packet will automatically cause the
      router to receive a copy of the packet that it can then deliver
      locally.  One must use care in these circumstances to prevent
      treating a received loop-back packet as a normal packet that was
      received (and then being subject to the rules of forwarding,
      etc.).



Baker                       Standards Track                    [Page 70]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


      Even without such a Link Layer, it is of course hardly necessary
      to make a copy of an entire packet to queue it both for forwarding
      and for local delivery, though care must be taken with fragments,
      since reassembly is performed on locally delivered packets but not
      on forwarded packets.  One simple scheme is to associate a flag
      with each packet on the router's output queue that indicates
      whether it should be queued for local delivery after it has been
      sent.

5.2.4 Determining the Next Hop Address

   When a router is going to forward a packet, it must determine whether
   it can send it directly to its destination, or whether it needs to
   pass it through another router.  If the latter, it needs to determine
   which router to use.  This section explains how these determinations
   are made.

   This section makes use of the following definitions:

   o LSRR - IP Loose Source and Record Route option

   o SSRR - IP Strict Source and Record Route option

   o Source Route Option - an LSRR or an SSRR

   o Ultimate Destination Address - where the packet is being sent to:
      the last address in the source route of a source-routed packet, or
      the destination address in the IP header of a non-source-routed
      packet

   o Adjacent - reachable without going through any IP routers

   o Next Hop Address - the IP address of the adjacent host or router to
      which the packet should be sent next

   o IP Destination Address - the ultimate destination address, except
      in source routed packets, where it is the next address specified
      in the source route

   o Immediate Destination - the node, System, router, end-system, or
      whatever that is addressed by the IP Destination Address.










Baker                       Standards Track                    [Page 71]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


5.2.4.1 IP Destination Address

   If:

   o the destination address in the IP header is one of the addresses of
      the router,

   o the packet contains a Source Route Option, and

   o the pointer in the Source Route Option does not point past the end
      of the option,

   then the next IP Destination Address is the address pointed at by the
   pointer in that option.  If:

   o the destination address in the IP header is one of the addresses of
      the router,

   o the packet contains a Source Route Option, and

   o the pointer in the Source Route Option points past the end of the
      option,

   then the message is addressed to the system analyzing the message.

   A router MUST use the IP Destination Address, not the Ultimate
   Destination Address (the last address in the source route option),
   when determining how to handle a packet.

   It is an error for more than one source route option to appear in a
   datagram.  If it receives such a datagram, it SHOULD discard the
   packet and reply with an ICMP Parameter Problem message whose pointer
   points at the beginning of the second source route option.

5.2.4.2 Local/Remote Decision

   After it has been determined that the IP packet needs to be forwarded
   according to the rules specified in Section [5.2.3], the following
   algorithm MUST be used to determine if the Immediate Destination is
   directly accessible (see [INTERNET:2]).

   (1) For each network interface that has not been assigned any IP
       address (the unnumbered lines as described in Section [2.2.7]),
       compare the router-id of the other end of the line to the IP
       Destination Address.  If they are exactly equal, the packet can
       be transmitted through this interface.





Baker                       Standards Track                    [Page 72]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   DISCUSSION
      In other words, the router or host at the remote end of the line
      is the destination of the packet or is the next step in the source
      route of a source routed packet.

   (2) If no network interface has been selected in the first step, for
       each IP address assigned to the router:

   (a) isolate the network prefix used by the interface.

   IMPLEMENTATION
      The result of this operation will usually have been computed and
      saved during initialization.

   (b) Isolate the corresponding set of bits from the IP Destination
      Address of the packet.

   (c) Compare the resulting network prefixes.  If they are equal to
      each other, the packet can be transmitted through the
      corresponding network interface.

   (3) If the destination was neither the router-id of a neighbor on an
       unnumbered interface nor a member of a directly connected network
       prefix, the IP Destination is accessible only through some other
       router.  The selection of the router and the next hop IP address
       is described in Section [5.2.4.3].  In the case of a host that is
       not also a router, this may be the configured default router.

   Ongoing work in the IETF [ARCH:9, NRHP] considers some cases such as
   when multiple IP (sub)networks are overlaid on the same link layer
   network.  Barring policy restrictions, hosts and routers using a
   common link layer network can directly communicate even if they are
   not in the same IP (sub)network, if there is adequate information
   present.  The Next Hop Routing Protocol (NHRP) enables IP entities to
   determine the "optimal" link layer address to be used to traverse
   such a link layer network towards a remote destination.

   (4) If the selected "next hop" is reachable through an interface
   configured to use NHRP, then the following additional steps apply:

     (a) Compare the IP Destination Address to the destination addresses
        in the NHRP cache.  If the address is in the cache, then send
        the datagram to the corresponding cached link layer address.
     (b) If the address is not in the cache, then construct an NHRP
        request packet containing the IP Destination Address.  This
        message is sent to the NHRP server configured for that
        interface.  This may be a logically separate process or entity
        in the router itself.



Baker                       Standards Track                    [Page 73]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


     (c) The NHRP server will respond with the proper link layer address
        to use to transmit the datagram and subsequent datagrams to the
        same destination.  The system MAY transmit the datagram(s) to
        the traditional "next hop" router while awaiting the NHRP reply.

5.2.4.3 Next Hop Address

   EDITORS+COMMENTS
      The router applies the algorithm in the previous section to
      determine if the IP Destination Address is adjacent.  If so, the
      next hop address is the same as the IP Destination Address.
      Otherwise, the packet must be forwarded through another router to
      reach its Immediate Destination.  The selection of this router is
      the topic of this section.

      If the packet contains an SSRR, the router MUST discard the packet
      and reply with an ICMP Bad Source Route error.  Otherwise, the
      router looks up the IP Destination Address in its routing table to
      determine an appropriate next hop address.

   DISCUSSION
      Per the IP specification, a Strict Source Route must specify a
      sequence of nodes through which the packet must traverse; the
      packet must go from one node of the source route to the next,
      traversing intermediate networks only.  Thus, if the router is not
      adjacent to the next step of the source route, the source route
      can not be fulfilled.  Therefore, the router rejects such with an
      ICMP Bad Source Route error.

   The goal of the next-hop selection process is to examine the entries
   in the router's Forwarding Information Base (FIB) and select the best
   route (if there is one) for the packet from those available in the
   FIB.

   Conceptually, any route lookup algorithm starts out with a set of
   candidate routes that consists of the entire contents of the FIB.
   The algorithm consists of a series of steps that discard routes from
   the set.  These steps are referred to as Pruning Rules.  Normally,
   when the algorithm terminates there is exactly one route remaining in
   the set.  If the set ever becomes empty, the packet is discarded
   because the destination is unreachable.  It is also possible for the
   algorithm to terminate when more than one route remains in the set.
   In this case, the router may arbitrarily discard all but one of them,
   or may perform "load-splitting" by choosing whichever of the routes
   has been least recently used.

   With the exception of rule 3 (Weak TOS), a router MUST use the
   following Pruning Rules when selecting a next hop for a packet.  If a



Baker                       Standards Track                    [Page 74]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   router does consider TOS when making next-hop decisions, the Rule 3
   must be applied in the order indicated below.  These rules MUST be
   (conceptually) applied to the FIB in the order that they are
   presented.  (For some historical perspective, additional pruning
   rules, and other common algorithms in use, see Appendix E.)

   DISCUSSION
      Rule 3 is optional in that Section [5.3.2] says that a router only
      SHOULD consider TOS when making forwarding decisions.


      (1) Basic Match
           This rule discards any routes to destinations other than the
           IP Destination Address of the packet.  For example, if a
           packet's IP Destination Address is 10.144.2.5, this step
           would discard a route to net 128.12.0.0/16 but would retain
           any routes to the network prefixes 10.0.0.0/8 and
           10.144.0.0/16, and any default routes.

           More precisely, we assume that each route has a destination
           attribute, called route.dest and a corresponding prefix
           length, called route.length, to specify which bits of
           route.dest are significant.  The IP Destination Address of
           the packet being forwarded is ip.dest.  This rule discards
           all routes from the set of candidates except those for which
           the most significant route.length bits of route.dest and
           ip.dest are equal.

           For example, if a packet's IP Destination Address is
           10.144.2.5 and there are network prefixes 10.144.1.0/24,
           10.144.2.0/24, and 10.144.3.0/24, this rule would keep only
           10.144.2.0/24; it is the only route whose prefix has the same
           value as the corresponding bits in the IP Destination Address
           of the packet.

      (2) Longest Match
           Longest Match is a refinement of Basic Match, described
           above.  After performing Basic Match pruning, the algorithm
           examines the remaining routes to determine which among them
           have the largest route.length values.  All except these are
           discarded.

           For example, if a packet's IP Destination Address is
           10.144.2.5 and there are network prefixes 10.144.2.0/24,
           10.144.0.0/16, and 10.0.0.0/8, then this rule would keep only
           the first (10.144.2.0/24) because its prefix length is
           longest.




Baker                       Standards Track                    [Page 75]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


      (3) Weak TOS
           Each route has a type of service attribute, called route.tos,
           whose possible values are assumed to be identical to those
           used in the TOS field of the IP header.  Routing protocols
           that distribute TOS information fill in route.tos
           appropriately in routes they add to the FIB; routes from
           other routing protocols are treated as if they have the
           default TOS (0000).  The TOS field in the IP header of the
           packet being routed is called ip.tos.

           The set of candidate routes is examined to determine if it
           contains any routes for which route.tos = ip.tos.  If so, all
           routes except those for which route.tos = ip.tos are
           discarded.  If not, all routes except those for which
           route.tos = 0000 are discarded from the set of candidate
           routes.

           Additional discussion of routing based on Weak TOS may be
           found in [ROUTE:11].

   DISCUSSION
      The effect of this rule is to select only those routes that have a
      TOS that matches the TOS requested in the packet.  If no such
      routes exist then routes with the default TOS are considered.
      Routes with a non-default TOS that is not the TOS requested in the
      packet are never used, even if such routes are the only available
      routes that go to the packet's destination.

     (4) Best Metric
          Each route has a metric attribute, called route.metric, and a
          routing domain identifier, called route.domain.  Each member
          of the set of candidate routes is compared with each other
          member of the set.  If route.domain is equal for the two
          routes and route.metric is strictly inferior for one when
          compared with the other, then the one with the inferior metric
          is discarded from the set.  The determination of inferior is
          usually by a simple arithmetic comparison, though some
          protocols may have structured metrics requiring more complex
          comparisons.

     (5) Vendor Policy
          Vendor Policy is sort of a catch-all to make up for the fact
          that the previously listed rules are often inadequate to
          choose from the possible routes.  Vendor Policy pruning rules
          are extremely vendor-specific.  See section [5.2.4.4].

     This algorithm has two distinct disadvantages.  Presumably, a
     router implementor might develop techniques to deal with these



Baker                       Standards Track                    [Page 76]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


     disadvantages and make them a part of the Vendor Policy pruning
     rule.

     (1) IS-IS and OSPF route classes are not directly handled.

     (2) Path properties other than type of service (e.g., MTU) are
          ignored.

     It is also worth noting a deficiency in the way that TOS is
     supported: routing protocols that support TOS are implicitly
     preferred when forwarding packets that have non-zero TOS values.

     The Basic Match and Longest Match pruning rules generalize the
     treatment of a number of particular types of routes.  These routes
     are selected in the following, decreasing, order of preference:

     (1) Host Route: This is a route to a specific end system.

     (2) Hierarchical Network Prefix Routes: This is a route to a
          particular network prefix.  Note that the FIB may contain
          several routes to network prefixes that subsume each other
          (one prefix is the other prefix with additional bits).  These
          are selected in order of decreasing prefix length.

     (5) Default Route: This is a route to all networks for which there
          are no explicit routes.  It is by definition the route whose
          prefix length is zero.

     If, after application of the pruning rules, the set of routes is
     empty (i.e., no routes were found), the packet MUST be discarded
     and an appropriate ICMP error generated (ICMP Bad Source Route if
     the IP Destination Address came from a source route option;
     otherwise, whichever of ICMP Destination Host Unreachable or
     Destination Network Unreachable is appropriate, as described in
     Section [4.3.3.1]).

5.2.4.4 Administrative Preference

     One suggested mechanism for the Vendor Policy Pruning Rule is to
     use administrative preference, which is a simple prioritization
     algorithm.  The idea is to manually prioritize the routes that one
     might need to select among.

     Each route has associated with it a preference value, based on
     various attributes of the route (specific mechanisms for assignment
     of preference values are suggested below).  This preference value
     is an integer in the range [0..255], with zero being the most
     preferred and 254 being the least preferred.  255 is a special



Baker                       Standards Track                    [Page 77]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


     value that means that the route should never be used.  The first
     step in the Vendor Policy pruning rule discards all but the most
     preferable routes (and always discards routes whose preference
     value is 255).

     This policy is not safe in that it can easily be misused to create
     routing loops.  Since no protocol ensures that the preferences
     configured for a router is consistent with the preferences
     configured in its neighbors, network managers must exercise care in
     configuring preferences.

     o Address Match
        It is useful to be able to assign a single preference value to
        all routes (learned from the same routing domain) to any of a
        specified set of destinations, where the set of destinations is
        all destinations that match a specified network prefix.

     o Route Class
        For routing protocols which maintain the distinction, it is
        useful to be able to assign a single preference value to all
        routes (learned from the same routing domain) which have a
        particular route class (intra-area, inter-area, external with
        internal metrics, or external with external metrics).

     o Interface
        It is useful to be able to assign a single preference value to
        all routes (learned from a particular routing domain) that would
        cause packets to be routed out a particular logical interface on
        the router (logical interfaces generally map one-to-one onto the
        router's network interfaces, except that any network interface
        that has multiple IP addresses will have multiple logical
        interfaces associated with it).

     o Source router
        It is useful to be able to assign a single preference value to
        all routes (learned from the same routing domain) that were
        learned from any of a set of routers, where the set of routers
        are those whose updates have a source address that match a
        specified network prefix.

     o Originating AS
        For routing protocols which provide the information, it is
        useful to be able to assign a single preference value to all
        routes (learned from a particular routing domain) which
        originated in another particular routing domain.  For BGP
        routes, the originating AS is the first AS listed in the route's
        AS_PATH attribute.  For OSPF external routes, the originating AS
        may be considered to be the low order 16 bits of the route's



Baker                       Standards Track                    [Page 78]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


        external route tag if the tag's Automatic bit is set and the
        tag's Path Length is not equal to 3.

     o External route tag
        It is useful to be able to assign a single preference value to
        all OSPF external routes (learned from the same routing domain)
        whose external route tags match any of a list of specified
        values.  Because the external route tag may contain a structured
        value, it may be useful to provide the ability to match
        particular subfields of the tag.

     o AS path
        It may be useful to be able to assign a single preference value
        to all BGP routes (learned from the same routing domain) whose
        AS path "matches" any of a set of specified values.  It is not
        yet clear exactly what kinds of matches are most useful.  A
        simple option would be to allow matching of all routes for which
        a particular AS number appears (or alternatively, does not
        appear) anywhere in the route's AS_PATH attribute.  A more
        general but somewhat more difficult alternative would be to
        allow matching all routes for which the AS path matches a
        specified regular expression.

5.2.4.5 Load Splitting

     At the end of the Next-hop selection process, multiple routes may
     still remain.  A router has several options when this occurs.  It
     may arbitrarily discard some of the routes.  It may reduce the
     number of candidate routes by comparing metrics of routes from
     routing domains that are not considered equivalent.  It may retain
     more than one route and employ a load-splitting mechanism to divide
     traffic among them.  Perhaps the only thing that can be said about
     the relative merits of the options is that load-splitting is useful
     in some situations but not in others, so a wise implementor who
     implements load-splitting will also provide a way for the network
     manager to disable it.

5.2.5 Unused IP Header Bits: RFC-791 Section 3.1

     The IP header contains several reserved bits, in the Type of
     Service field and in the Flags field.  Routers MUST NOT drop
     packets merely because one or more of these reserved bits has a
     non-zero value.

     Routers MUST ignore and MUST pass through unchanged the values of
     these reserved bits.  If a router fragments a packet, it MUST copy
     these bits into each fragment.




Baker                       Standards Track                    [Page 79]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   DISCUSSION
      Future revisions to the IP protocol may make use of these unused
      bits.  These rules are intended to ensure that these revisions can
      be deployed without having to simultaneously upgrade all routers
      in the Internet.

5.2.6 Fragmentation and Reassembly: RFC-791 Section 3.2

   As was discussed in Section [4.2.2.7], a router MUST support IP
   fragmentation.

   A router MUST NOT reassemble any datagram before forwarding it.

   DISCUSSION
      A few people have suggested that there might be some topologies
      where reassembly of transit datagrams by routers might improve
      performance.  The fact that fragments may take different paths to
      the destination precludes safe use of such a feature.

      Nothing in this section should be construed to control or limit
      fragmentation or reassembly performed as a link layer function by
      the router.

      Similarly, if an IP datagram is encapsulated in another IP
      datagram (e.g., it is tunnelled), that datagram is in turn
      fragmented, the fragments must be reassembled in order to forward
      the original datagram.  This section does not preclude this.

5.2.7 Internet Control Message Protocol - ICMP

   General requirements for ICMP were discussed in Section [4.3].  This
   section discusses ICMP messages that are sent only by routers.

5.2.7.1 Destination Unreachable

   The ICMP Destination Unreachable message is sent by a router in
   response to a packet which it cannot forward because the destination
   (or next hop) is unreachable or a service is unavailable.  Examples
   of such cases include a message addressed to a host which is not
   there and therefore does not respond to ARP requests, and messages
   addressed to network prefixes for which the router has no valid
   route.

   A router MUST be able to generate ICMP Destination Unreachable
   messages and SHOULD choose a response code that most closely matches
   the reason the message is being generated.

   The following codes are defined in [INTERNET:8] and [INTRO:2]:



Baker                       Standards Track                    [Page 80]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   0 = Network Unreachable - generated by a router if a forwarding path
        (route) to the destination network is not available;

   1 = Host Unreachable - generated by a router if a forwarding path
        (route) to the destination host on a directly connected network
        is not available (does not respond to ARP);

   2 = Protocol Unreachable - generated if the transport protocol
        designated in a datagram is not supported in the transport layer
        of the final destination;

   3 = Port Unreachable - generated if the designated transport protocol
        (e.g., UDP) is unable to demultiplex the datagram in the
        transport layer of the final destination but has no protocol
        mechanism to inform the sender;

   4 = Fragmentation Needed and DF Set - generated if a router needs to
        fragment a datagram but cannot since the DF flag is set;

   5 = Source Route Failed - generated if a router cannot forward a
        packet to the next hop in a source route option;

   6 = Destination Network Unknown - This code SHOULD NOT be generated
        since it would imply on the part of the router that the
        destination network does not exist (net unreachable code 0
        SHOULD be used in place of code 6);

   7 = Destination Host Unknown - generated only when a router can
        determine (from link layer advice) that the destination host
        does not exist;

   11 = Network Unreachable For Type Of Service - generated by a router
        if a forwarding path (route) to the destination network with the
        requested or default TOS is not available;

   12 = Host Unreachable For Type Of Service - generated if a router
        cannot forward a packet because its route(s) to the destination
        do not match either the TOS requested in the datagram or the
        default TOS (0).

   The following additional codes are hereby defined:

   13 = Communication Administratively Prohibited - generated if a
        router cannot forward a packet due to administrative filtering;

   14 = Host Precedence Violation.  Sent by the first hop router to a
        host to indicate that a requested precedence is not permitted
        for the particular combination of source/destination host or



Baker                       Standards Track                    [Page 81]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


        network, upper layer protocol, and source/destination port;

   15 = Precedence cutoff in effect.  The network operators have imposed
        a minimum level of precedence required for operation, the
        datagram was sent with a precedence below this level;

   NOTE: [INTRO:2] defined Code 8 for source host isolated.  Routers
   SHOULD NOT generate Code 8; whichever of Codes 0 (Network
   Unreachable) and 1 (Host Unreachable) is appropriate SHOULD be used
   instead.  [INTRO:2] also defined Code 9 for communication with
   destination network administratively prohibited and Code 10 for
   communication with destination host administratively prohibited.
   These codes were intended for use by end-to-end encryption devices
   used by U.S military agencies.  Routers SHOULD use the newly defined
   Code 13 (Communication Administratively Prohibited) if they
   administratively filter packets.

   Routers MAY have a configuration option that causes Code 13
   (Communication Administratively Prohibited) messages not to be
   generated.  When this option is enabled, no ICMP error message is
   sent in response to a packet that is dropped because its forwarding
   is administratively prohibited.

   Similarly, routers MAY have a configuration option that causes Code
   14 (Host Precedence Violation) and Code 15 (Precedence Cutoff in
   Effect) messages not to be generated.  When this option is enabled,
   no ICMP error message is sent in response to a packet that is dropped
   because of a precedence violation.

   Routers MUST use Host Unreachable or Destination Host Unknown codes
   whenever other hosts on the same destination network might be
   reachable; otherwise, the source host may erroneously conclude that
   all hosts on the network are unreachable, and that may not be the
   case.

   [INTERNET:14] describes a slight modification the form of Destination
   Unreachable messages containing Code 4 (Fragmentation needed and DF
   set).  A router MUST use this modified form when originating Code 4
   Destination Unreachable messages.

5.2.7.2 Redirect

   The ICMP Redirect message is generated to inform a local host the it
   should use a different next hop router for a certain class of
   traffic.

   Routers MUST NOT generate the Redirect for Network or Redirect for
   Network and Type of Service messages (Codes 0 and 2) specified in



Baker                       Standards Track                    [Page 82]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   [INTERNET:8].  Routers MUST be able to generate the Redirect for Host
   message (Code 1) and SHOULD be able to generate the Redirect for Type
   of Service and Host message (Code 3) specified in [INTERNET:8].

   DISCUSSION
      If the directly connected network is not subnetted (in the
      classical sense), a router can normally generate a network
      Redirect that applies to all hosts on a specified remote network.
      Using a network rather than a host Redirect may economize slightly
      on network traffic and on host routing table storage.  However,
      the savings are not significant, and subnets create an ambiguity
      about the subnet mask to be used to interpret a network Redirect.
      In a CIDR environment, it is difficult to specify precisely the
      cases in which network Redirects can be used.  Therefore, routers
      must send only host (or host and type of service) Redirects.

   A Code 3 (Redirect for Host and Type of Service) message is generated
   when the packet provoking the redirect has a destination for which
   the path chosen by the router would depend (in part) on the TOS
   requested.

   Routers that can generate Code 3 redirects (Host and Type of Service)
   MUST have a configuration option (which defaults to on) to enable
   Code 1 (Host) redirects to be substituted for Code 3 redirects.  A
   router MUST send a Code 1 Redirect in place of a Code 3 Redirect if
   it has been configured to do so.

   If a router is not able to generate Code 3 Redirects then it MUST
   generate Code 1 Redirects in situations where a Code 3 Redirect is
   called for.

   Routers MUST NOT generate a Redirect Message unless all the following
   conditions are met:

   o The packet is being forwarded out the same physical interface that
      it was received from,

   o The IP source address in the packet is on the same Logical IP
      (sub)network as the next-hop IP address, and

   o The packet does not contain an IP source route option.

   The source address used in the ICMP Redirect MUST belong to the same
   logical (sub)net as the destination address.

   A router using a routing protocol (other than static routes) MUST NOT
   consider paths learned from ICMP Redirects when forwarding a packet.
   If a router is not using a routing protocol, a router MAY have a



Baker                       Standards Track                    [Page 83]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   configuration that, if set, allows the router to consider routes
   learned through ICMP Redirects when forwarding packets.

   DISCUSSION
      ICMP Redirect is a mechanism for routers to convey routing
      information to hosts.  Routers use other mechanisms to learn
      routing information, and therefore have no reason to obey
      redirects.  Believing a redirect which contradicted the router's
      other information would likely create routing loops.

      On the other hand, when a router is not acting as a router, it
      MUST comply with the behavior required of a host.

5.2.7.3 Time Exceeded

   A router MUST generate a Time Exceeded message Code 0 (In Transit)
   when it discards a packet due to an expired TTL field.  A router MAY
   have a per-interface option to disable origination of these messages
   on that interface, but that option MUST default to allowing the
   messages to be originated.

5.2.8 INTERNET GROUP MANAGEMENT PROTOCOL - IGMP

   IGMP [INTERNET:4] is a protocol used between hosts and multicast
   routers on a single physical network to establish hosts' membership
   in particular multicast groups.  Multicast routers use this
   information, in conjunction with a multicast routing protocol, to
   support IP multicast forwarding across the Internet.

   A router SHOULD implement the multicast router part of IGMP.





















Baker                       Standards Track                    [Page 84]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


5.3 SPECIFIC ISSUES

5.3.1 Time to Live (TTL)

   The Time-to-Live (TTL) field of the IP header is defined to be a
   timer limiting the lifetime of a datagram.  It is an 8-bit field and
   the units are seconds.  Each router (or other module) that handles a
   packet MUST decrement the TTL by at least one, even if the elapsed
   time was much less than a second.  Since this is very often the case,
   the TTL is effectively a hop count limit on how far a datagram can
   propagate through the Internet.

   When a router forwards a packet, it MUST reduce the TTL by at least
   one.  If it holds a packet for more than one second, it MAY decrement
   the TTL by one for each second.

   If the TTL is reduced to zero (or less), the packet MUST be
   discarded, and if the destination is not a multicast address the
   router MUST send an ICMP Time Exceeded message, Code 0 (TTL Exceeded
   in Transit) message to the source.  Note that a router MUST NOT
   discard an IP unicast or broadcast packet with a non-zero TTL merely
   because it can predict that another router on the path to the
   packet's final destination will decrement the TTL to zero.  However,
   a router MAY do so for IP multicasts, in order to more efficiently
   implement IP multicast's expanding ring search algorithm (see
   [INTERNET:4]).

   DISCUSSION
      The IP TTL is used, somewhat schizophrenically, as both a hop
      count limit and a time limit.  Its hop count function is critical
      to ensuring that routing problems can't melt down the network by
      causing packets to loop infinitely in the network.  The time limit
      function is used by transport protocols such as TCP to ensure
      reliable data transfer.  Many current implementations treat TTL as
      a pure hop count, and in parts of the Internet community there is
      a strong sentiment that the time limit function should instead be
      performed by the transport protocols that need it.

      In this specification, we have reluctantly decided to follow the
      strong belief among the router vendors that the time limit
      function should be optional.  They argued that implementation of
      the time limit function is difficult enough that it is currently
      not generally done.  They further pointed to the lack of
      documented cases where this shortcut has caused TCP to corrupt
      data (of course, we would expect the problems created to be rare
      and difficult to reproduce, so the lack of documented cases
      provides little reassurance that there haven't been a number of
      undocumented cases).



Baker                       Standards Track                    [Page 85]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


      IP multicast notions such as the expanding ring search may not
      work as expected unless the TTL is treated as a pure hop count.
      The same thing is somewhat true of traceroute.

      ICMP Time Exceeded messages are required because the traceroute
      diagnostic tool depends on them.

      Thus, the tradeoff is between severely crippling, if not
      eliminating, two very useful tools and avoiding a very rare and
      transient data transport problem that may not occur at all.  We
      have chosen to preserve the tools.

5.3.2 Type of Service (TOS)

      The Type-of-Service byte in the IP header is divided into three
      sections: the Precedence field (high-order 3 bits), a field that
      is customarily called Type of Service or "TOS (next 4 bits), and a
      reserved bit (the low order bit).  Rules governing the reserved
      bit were described in Section [4.2.2.3].  The Precedence field
      will be discussed in Section [5.3.3].  A more extensive discussion
      of the TOS field and its use can be found in [ROUTE:11].

      A router SHOULD consider the TOS field in a packet's IP header
      when deciding how to forward it.  The remainder of this section
      describes the rules that apply to routers that conform to this
      requirement.

      A router MUST maintain a TOS value for each route in its routing
      table.  Routes learned through a routing protocol that does not
      support TOS MUST be assigned a TOS of zero (the default TOS).

      To choose a route to a destination, a router MUST use an algorithm
      equivalent to the following:

      (1) The router locates in its routing table all available routes
           to the destination (see Section [5.2.4]).

      (2) If there are none, the router drops the packet because the
           destination is unreachable.  See section [5.2.4].

      (3) If one or more of those routes have a TOS that exactly matches
           the TOS specified in the packet, the router chooses the route
           with the best metric.

      (4) Otherwise, the router repeats the above step, except looking
           at routes whose TOS is zero.





Baker                       Standards Track                    [Page 86]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


      (5) If no route was chosen above, the router drops the packet
           because the destination is unreachable.  The router returns
           an ICMP Destination Unreachable error specifying the
           appropriate code: either Network Unreachable with Type of
           Service (code 11) or Host Unreachable with Type of Service
           (code 12).

   DISCUSSION
      Although TOS has been little used in the past, its use by hosts is
      now mandated by the Requirements for Internet Hosts RFCs
      ([INTRO:2] and [INTRO:3]).  Support for TOS in routers may become
      a MUST in the future, but is a SHOULD for now until we get more
      experience with it and can better judge both its benefits and its
      costs.

      Various people have proposed that TOS should affect other aspects
      of the forwarding function.  For example:

      (1) A router could place packets that have the Low Delay bit set
           ahead of other packets in its output queues.

      (2) a router is forced to discard packets, it could try to avoid
           discarding those which have the High Reliability bit set.

      These ideas have been explored in more detail in [INTERNET:17] but
      we don't yet have enough experience with such schemes to make
      requirements in this area.

5.3.3 IP Precedence

      This section specifies requirements and guidelines for appropriate
      processing of the IP Precedence field in routers.  Precedence is a
      scheme for allocating resources in the network based on the
      relative importance of different traffic flows.  The IP
      specification defines specific values to be used in this field for
      various types of traffic.

      The basic mechanisms for precedence processing in a router are
      preferential resource allocation, including both precedence-
      ordered queue service and precedence-based congestion control, and
      selection of Link Layer priority features.  The router also
      selects the IP precedence for routing, management and control
      traffic it originates.  For a more extensive discussion of IP
      Precedence and its implementation see [FORWARD:6].

      Precedence-ordered queue service, as discussed in this section,
      includes but is not limited to the queue for the forwarding
      process and queues for outgoing links.  It is intended that a



Baker                       Standards Track                    [Page 87]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


      router supporting precedence should also use the precedence
      indication at whatever points in its processing are concerned with
      allocation of finite resources, such as packet buffers or Link
      Layer connections.  The set of such points is implementation-
      dependent.

   DISCUSSION
      Although the Precedence field was originally provided for use in
      DOD systems where large traffic surges or major damage to the
      network are viewed as inherent threats, it has useful applications
      for many non-military IP networks.  Although the traffic handling
      capacity of networks has grown greatly in recent years, the
      traffic generating ability of the users has also grown, and
      network overload conditions still occur at times.  Since IP-based
      routing and management protocols have become more critical to the
      successful operation of the Internet, overloads present two
      additional risks to the network:

      (1) High delays may result in routing protocol packets being lost.
           This may cause the routing protocol to falsely deduce a
           topology change and propagate this false information to other
           routers.  Not only can this cause routes to oscillate, but an
           extra processing burden may be placed on other routers.

      (2) High delays may interfere with the use of network management
           tools to analyze and perhaps correct or relieve the problem
           in the network that caused the overload condition to occur.

      Implementation and appropriate use of the Precedence mechanism
      alleviates both of these problems.

5.3.3.1 Precedence-Ordered Queue Service

   Routers SHOULD implement precedence-ordered queue service.
   Precedence-ordered queue service means that when a packet is selected
   for output on a (logical) link, the packet of highest precedence that
   has been queued for that link is sent.  Routers that implement
   precedence-ordered queue service MUST also have a configuration
   option to suppress precedence-ordered queue service in the Internet
   Layer.

   Any router MAY implement other policy-based throughput management
   procedures that result in other than strict precedence ordering, but
   it MUST be configurable to suppress them (i.e., use strict ordering).

   As detailed in Section [5.3.6], routers that implement precedence-
   ordered queue service discard low precedence packets before
   discarding high precedence packets for congestion control purposes.



Baker                       Standards Track                    [Page 88]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   Preemption (interruption of processing or transmission of a packet)
   is not envisioned as a function of the Internet Layer.  Some
   protocols at other layers may provide preemption features.

5.3.3.2 Lower Layer Precedence Mappings

   Routers that implement precedence-ordered queuing MUST IMPLEMENT, and
   other routers SHOULD IMPLEMENT, Lower Layer Precedence Mapping.

   A router that implements Lower Layer Precedence Mapping:

   o MUST be able to map IP Precedence to Link Layer priority mechanisms
      for link layers that have such a feature defined.

   o MUST have a configuration option to select the Link Layer's default
      priority treatment for all IP traffic

   o SHOULD be able to configure specific nonstandard mappings of IP
      precedence values to Link Layer priority values for each
      interface.

   DISCUSSION
      Some research questions the workability of the priority features
      of some Link Layer protocols, and some networks may have faulty
      implementations of the link layer priority mechanism.  It seems
      prudent to provide an escape mechanism in case such problems show
      up in a network.

      On the other hand, there are proposals to use novel queuing
      strategies to implement special services such as multimedia
      bandwidth reservation or low-delay service.  Special services and
      queuing strategies to support them are current research subjects
      and are in the process of standardization.

      Implementors may wish to consider that correct link layer mapping
      of IP precedence is required by DOD policy for TCP/IP systems used
      on DOD networks.  Since these requirements are intended to
      encourage (but not force) the use of precedence features in the
      hope of providing better Internet service to all users, routers
      supporting precedence-ordered queue service should default to
      maintaining strict precedence ordering regardless of the type of
      service requested.









Baker                       Standards Track                    [Page 89]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


5.3.3.3 Precedence Handling For All Routers

   A router (whether or not it employs precedence-ordered queue
   service):

   (1) MUST accept and process incoming traffic of all precedence levels
        normally, unless it has been administratively configured to do
        otherwise.

   (2) MAY implement a validation filter to administratively restrict
        the use of precedence levels by particular traffic sources.  If
        provided, this filter MUST NOT filter out or cut off the
        following sorts of ICMP error messages: Destination Unreachable,
        Redirect, Time Exceeded, and Parameter Problem.  If this filter
        is provided, the procedures required for packet filtering by
        addresses are required for this filter also.

   DISCUSSION
      Precedence filtering should be applicable to specific
      source/destination IP Address pairs, specific protocols, specific
      ports, and so on.

   An ICMP Destination Unreachable message with code 14 SHOULD be sent
   when a packet is dropped by the validation filter, unless this has
   been suppressed by configuration choice.

   (3) MAY implement a cutoff function that allows the router to be set
        to refuse or drop traffic with precedence below a specified
        level.  This function may be activated by management actions or
        by some implementation dependent heuristics, but there MUST be a
        configuration option to disable any heuristic mechanism that
        operates without human intervention.  An ICMP Destination
        Unreachable message with code 15 SHOULD be sent when a packet is
        dropped by the cutoff function, unless this has been suppressed
        by configuration choice.

        A router MUST NOT refuse to forward datagrams with IP precedence
        of 6 (Internetwork Control) or 7 (Network Control) solely due to
        precedence cutoff.  However, other criteria may be used in
        conjunction with precedence cutoff to filter high precedence
        traffic.

   DISCUSSION
      Unrestricted precedence cutoff could result in an unintentional
      cutoff of routing and control traffic.  In the general case, host
      traffic should be restricted to a value of 5 (CRITIC/ECP) or
      below; this is not a requirement and may not be correct in certain
      systems.



Baker                       Standards Track                    [Page 90]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   (4) MUST NOT change precedence settings on packets it did not
        originate.

   (5) SHOULD be able to configure distinct precedence values to be used
        for each routing or management protocol supported (except for
        those protocols, such as OSPF, which specify which precedence
        value must be used).

   (6) MAY be able to configure routing or management traffic precedence
        values independently for each peer address.

   (7) MUST respond appropriately to Link Layer precedence-related error
        indications where provided.  An ICMP Destination Unreachable
        message with code 15 SHOULD be sent when a packet is dropped
        because a link cannot accept it due to a precedence-related
        condition, unless this has been suppressed by configuration
        choice.

   DISCUSSION
      The precedence cutoff mechanism described in (3) is somewhat
      controversial.  Depending on the topological location of the area
      affected by the cutoff, transit traffic may be directed by routing
      protocols into the area of the cutoff, where it will be dropped.
      This is only a problem if another path that is unaffected by the
      cutoff exists between the communicating points.  Proposed ways of
      avoiding this problem include providing some minimum bandwidth to
      all precedence levels even under overload conditions, or
      propagating cutoff information in routing protocols.  In the
      absence of a widely accepted (and implemented) solution to this
      problem, great caution is recommended in activating cutoff
      mechanisms in transit networks.

      A transport layer relay could legitimately provide the function
      prohibited by (4) above.  Changing precedence levels may cause
      subtle interactions with TCP and perhaps other protocols; a
      correct design is a non-trivial task.

      The intent of (5) and (6) (and the discussion of IP Precedence in
      ICMP messages in Section [4.3.2]) is that the IP precedence bits
      should be appropriately set, whether or not this router acts upon
      those bits in any other way.  We expect that in the future
      specifications for routing protocols and network management
      protocols will specify how the IP Precedence should be set for
      messages sent by those protocols.

      The appropriate response for (7) depends on the link layer
      protocol in use.  Typically, the router should stop trying to send
      offensive traffic to that destination for some period of time, and



Baker                       Standards Track                    [Page 91]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


      should return an ICMP Destination Unreachable message with code 15
      (service not available for precedence requested) to the traffic
      source.  It also should not try to reestablish a preempted Link
      Layer connection for some time.

5.3.4 Forwarding of Link Layer Broadcasts

   The encapsulation of IP packets in most Link Layer protocols (except
   PPP) allows a receiver to distinguish broadcasts and multicasts from
   unicasts simply by examining the Link Layer protocol headers (most
   commonly, the Link Layer destination address).  The rules in this
   section that refer to Link Layer broadcasts apply only to Link Layer
   protocols that allow broadcasts to be distinguished; likewise, the
   rules that refer to Link Layer multicasts apply only to Link Layer
   protocols that allow multicasts to be distinguished.

   A router MUST NOT forward any packet that the router received as a
   Link Layer broadcast, unless it is directed to an IP Multicast
   address.  In this latter case, one would presume that link layer
   broadcast was used due to the lack of an effective multicast service.

   A router MUST NOT forward any packet which the router received as a
   Link Layer multicast unless the packet's destination address is an IP
   multicast address.

   A router SHOULD silently discard a packet that is received via a Link
   Layer broadcast but does not specify an IP multicast or IP broadcast
   destination address.

   When a router sends a packet as a Link Layer broadcast, the IP
   destination address MUST be a legal IP broadcast or IP multicast
   address.

5.3.5 Forwarding of Internet Layer Broadcasts

   There are two major types of IP broadcast addresses; limited
   broadcast and directed broadcast.  In addition, there are three
   subtypes of directed broadcast: a broadcast directed to a specified
   network prefix, a broadcast directed to a specified subnetwork, and a
   broadcast directed to all subnets of a specified network.
   Classification by a router of a broadcast into one of these
   categories depends on the broadcast address and on the router's
   understanding (if any) of the subnet structure of the destination
   network.  The same broadcast will be classified differently by
   different routers.

   A limited IP broadcast address is defined to be all-ones: { -1, -1 }
   or 255.255.255.255.



Baker                       Standards Track                    [Page 92]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   A network-prefix-directed broadcast is composed of the network prefix
   of the IP address with a local part of all-ones or { , -1 }.  For example, a Class A net broadcast address is
   net.255.255.255, a Class B net broadcast address is net.net.255.255
   and a Class C net broadcast address is net.net.net.255 where net is a
   byte of the network address.

   The all-subnets-directed-broadcast is not well defined in a CIDR
   environment, and was deprecated in version 1 of this memo.

   As was described in Section [4.2.3.1], a router may encounter certain
   non-standard IP broadcast addresses:

   o 0.0.0.0 is an obsolete form of the limited broadcast address

   o { , 0 } is an obsolete form of a network-prefix-
      directed broadcast address.

   As was described in that section, packets addressed to any of these
   addresses SHOULD be silently discarded, but if they are not, they
   MUST be treated according to the same rules that apply to packets
   addressed to the non-obsolete forms of the broadcast addresses
   described above.  These rules are described in the next few sections.

5.3.5.1 Limited Broadcasts

   Limited broadcasts MUST NOT be forwarded.  Limited broadcasts MUST
   NOT be discarded.  Limited broadcasts MAY be sent and SHOULD be sent
   instead of directed broadcasts where limited broadcasts will suffice.

   DISCUSSION
      Some routers contain UDP servers which function by resending the
      requests (as unicasts or directed broadcasts) to other servers.
      This requirement should not be interpreted as prohibiting such
      servers.  Note, however, that such servers can easily cause packet
      looping if misconfigured.  Thus, providers of such servers would
      probably be well advised to document their setup carefully and to
      consider carefully the TTL on packets that are sent.

5.3.5.2 Directed Broadcasts

   A router MUST classify as network-prefix-directed broadcasts all
   valid, directed broadcasts destined for a remote network or an
   attached nonsubnetted network.  Note that in view of CIDR, such
   appear to be host addresses within the network prefix; we preclude
   inspection of the host part of such network prefixes.  Given a route
   and no overriding policy, then, a router MUST forward network-
   prefix-directed broadcasts.  Network-Prefix-Directed broadcasts MAY



Baker                       Standards Track                    [Page 93]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   be sent.

   A router MAY have an option to disable receiving network-prefix-
   directed broadcasts on an interface and MUST have an option to
   disable forwarding network-prefix-directed broadcasts.  These options
   MUST default to permit receiving and forwarding network-prefix-
   directed broadcasts.

   DISCUSSION
      There has been some debate about forwarding or not forwarding
      directed broadcasts.  In this memo we have made the forwarding
      decision depend on the router's knowledge of the destination
      network prefix.  Routers cannot determine that a message is
      unicast or directed broadcast apart from this knowledge.  The
      decision to forward or not forward the message is by definition
      only possible in the last hop router.

5.3.5.3 All-subnets-directed Broadcasts

   The first version of this memo described an algorithm for
   distributing a directed broadcast to all the subnets of a classical
   network number.  This algorithm was stated to be "broken," and
   certain failure cases were specified.

   In a CIDR routing domain, wherein classical IP network numbers are
   meaningless, the concept of an all-subnets-directed-broadcast is also
   meaningless.  To the knowledge of the working group, the facility was
   never implemented or deployed, and is now relegated to the dustbin of
   history.

5.3.5.4  Subnet-directed Broadcasts

   The first version of this memo spelled out procedures for dealing
   with subnet-directed-broadcasts.  In a CIDR routing domain, these are
   indistinguishable from net-drected-broadcasts.  The two are therefore
   treated together in section [5.3.5.2 Directed Broadcasts], and should
   be viewed as network-prefix directed broadcasts.

5.3.6 Congestion Control

   Congestion in a network is loosely defined as a condition where
   demand for resources (usually bandwidth or CPU time) exceeds
   capacity.  Congestion avoidance tries to prevent demand from
   exceeding capacity, while congestion recovery tries to restore an
   operative state.  It is possible for a router to contribute to both
   of these mechanisms.  A great deal of effort has been spent studying
   the problem.  The reader is encouraged to read [FORWARD:2] for a
   survey of the work.  Important papers on the subject include



Baker                       Standards Track                    [Page 94]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   [FORWARD:3], [FORWARD:4], [FORWARD:5], [FORWARD:10], [FORWARD:11],
   [FORWARD:12], [FORWARD:13], [FORWARD:14], and [INTERNET:10], among
   others.

   The amount of storage that router should have available to handle
   peak instantaneous demand when hosts use reasonable congestion
   policies, such as described in [FORWARD:5], is a function of the
   product of the bandwidth of the link times the path delay of the
   flows using the link, and therefore storage should increase as this
   Bandwidth*Delay product increases.  The exact function relating
   storage capacity to probability of discard is not known.

   When a router receives a packet beyond its storage capacity it must
   (by definition, not by decree) discard it or some other packet or
   packets.  Which packet to discard is the subject of much study but,
   unfortunately, little agreement so far.  The best wisdom to date
   suggests discarding a packet from the data stream most heavily using
   the link.  However, a number of additional factors may be relevant,
   including the precedence of the traffic, active bandwidth
   reservation, and the complexity associated with selecting that
   packet.

   A router MAY discard the packet it has just received; this is the
   simplest but not the best policy.  Ideally, the router should select
   a packet from one of the sessions most heavily abusing the link,
   given that the applicable Quality of Service policy permits this.  A
   recommended policy in datagram environments using FIFO queues is to
   discard a packet randomly selected from the queue (see [FORWARD:5]).
   An equivalent algorithm in routers using fair queues is to discard
   from the longest queue or that using the greatest virtual time (see
   [FORWARD:13]).  A router MAY use these algorithms to determine which
   packet to discard.

   If a router implements a discard policy (such as Random Drop) under
   which it chooses a packet to discard from a pool of eligible packets:

   o If precedence-ordered queue service (described in Section
      [5.3.3.1]) is implemented and enabled, the router MUST NOT discard
      a packet whose IP precedence is higher than that of a packet that
      is not discarded.

   o A router MAY protect packets whose IP headers request the maximize
      reliability TOS, except where doing so would be in violation of
      the previous rule.

   o A router MAY protect fragmented IP packets, on the theory that
      dropping a fragment of a datagram may increase congestion by
      causing all fragments of the datagram to be retransmitted by the



Baker                       Standards Track                    [Page 95]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


      source.

   o To help prevent routing perturbations or disruption of management
      functions, the router MAY protect packets used for routing
      control, link control, or network management from being discarded.
      Dedicated routers (i.e., routers that are not also general purpose
      hosts, terminal servers, etc.) can achieve an approximation of
      this rule by protecting packets whose source or destination is the
      router itself.

   Advanced methods of congestion control include a notion of fairness,
   so that the 'user' that is penalized by losing a packet is the one
   that contributed the most to the congestion.  No matter what
   mechanism is implemented to deal with bandwidth congestion control,
   it is important that the CPU effort expended be sufficiently small
   that the router is not driven into CPU congestion also.

   As described in Section [4.3.3.3], this document recommends that a
   router SHOULD NOT send a Source Quench to the sender of the packet
   that it is discarding.  ICMP Source Quench is a very weak mechanism,
   so it is not necessary for a router to send it, and host software
   should not use it exclusively as an indicator of congestion.

5.3.7 Martian Address Filtering

   An IP source address is invalid if it is a special IP address, as
   defined in 4.2.2.11 or 5.3.7, or is not a unicast address.

   An IP destination address is invalid if it is among those defined as
   illegal destinations in 4.2.3.1, or is a Class E address (except
   255.255.255.255).

   A router SHOULD NOT forward any packet that has an invalid IP source
   address or a source address on network 0.  A router SHOULD NOT
   forward, except over a loopback interface, any packet that has a
   source address on network 127.  A router MAY have a switch that
   allows the network manager to disable these checks.  If such a switch
   is provided, it MUST default to performing the checks.

   A router SHOULD NOT forward any packet that has an invalid IP
   destination address or a destination address on network 0.  A router
   SHOULD NOT forward, except over a loopback interface, any packet that
   has a destination address on network 127.  A router MAY have a switch
   that allows the network manager to disable these checks.  If such a
   switch is provided, it MUST default to performing the checks.

   If a router discards a packet because of these rules, it SHOULD log
   at least the IP source address, the IP destination address, and, if



Baker                       Standards Track                    [Page 96]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   the problem was with the source address, the physical interface on
   which the packet was received and the Link Layer address of the host
   or router from which the packet was received.

5.3.8 Source Address Validation

   A router SHOULD IMPLEMENT the ability to filter traffic based on a
   comparison of the source address of a packet and the forwarding table
   for a logical interface on which the packet was received.  If this
   filtering is enabled, the router MUST silently discard a packet if
   the interface on which the packet was received is not the interface
   on which a packet would be forwarded to reach the address contained
   in the source address.  In simpler terms, if a router wouldn't route
   a packet containing this address through a particular interface, it
   shouldn't believe the address if it appears as a source address in a
   packet read from this interface.

   If this feature is implemented, it MUST be disabled by default.

   DISCUSSION
      This feature can provide useful security improvements in some
      situations, but can erroneously discard valid packets in
      situations where paths are asymmetric.

5.3.9 Packet Filtering and Access Lists

   As a means of providing security and/or limiting traffic through
   portions of a network a router SHOULD provide the ability to
   selectively forward (or filter) packets.  If this capability is
   provided, filtering of packets SHOULD be configurable either to
   forward all packets or to selectively forward them based upon the
   source and destination prefixes, and MAY filter on other message
   attributes.  Each source and destination address SHOULD allow
   specification of an arbitrary prefix length.

   DISCUSSION
      This feature can provide a measure of privacy, where systems
      outside a boundary are not permitted to exchange certain protocols
      with systems inside the boundary, or are limited as to which
      systems they may communicate with.  It can also help prevent
      certain classes of security breach, wherein a system outside a
      boundary masquerades as a system inside the boundary and mimics a
      session with it.

   If supported, a router SHOULD be configurable to allow one of an

   o Include list - specification of a list of message definitions to be
      forwarded, or an



Baker                       Standards Track                    [Page 97]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   o Exclude list - specification of a list of message definitions NOT
      to be forwarded.

   A "message definition", in this context, specifies the source and
   destination network prefix, and may include other identifying
   information such as IP Protocol Type or TCP port number.

   A router MAY provide a configuration switch that allows a choice
   between specifying an include or an exclude list, or other equivalent
   controls.

   A value matching any address (e.g., a keyword any, an address with a
   mask of all 0's, or a network prefix whose length is zero) MUST be
   allowed as a source and/or destination address.

   In addition to address pairs, the router MAY allow any combination of
   transport and/or application protocol and source and destination
   ports to be specified.

   The router MUST allow packets to be silently discarded (i.e.,
   discarded without an ICMP error message being sent).

   The router SHOULD allow an appropriate ICMP unreachable message to be
   sent when a packet is discarded.  The ICMP message SHOULD specify
   Communication Administratively Prohibited (code 13) as the reason for
   the destination being unreachable.

   The router SHOULD allow the sending of ICMP destination unreachable
   messages (code 13) to be configured for each combination of address
   pairs, protocol types, and ports it allows to be specified.

   The router SHOULD count and SHOULD allow selective logging of packets
   not forwarded.

5.3.10 Multicast Routing

   An IP router SHOULD support forwarding of IP multicast packets, based
   either on static multicast routes or on routes dynamically determined
   by a multicast routing protocol (e.g., DVMRP [ROUTE:9]).  A router
   that forwards IP multicast packets is called a multicast router.

5.3.11 Controls on Forwarding

   For each physical interface, a router SHOULD have a configuration
   option that specifies whether forwarding is enabled on that
   interface.  When forwarding on an interface is disabled, the router:





Baker                       Standards Track                    [Page 98]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   o MUST silently discard any packets which are received on that
      interface but are not addressed to the router

   o MUST NOT send packets out that interface, except for datagrams
      originated by the router

   o MUST NOT announce via any routing protocols the availability of
      paths through the interface

   DISCUSSION
      This feature allows the network manager to essentially turn off an
      interface but leaves it accessible for network management.

      Ideally, this control would apply to logical rather than physical
      interfaces.  It cannot, because there is no known way for a router
      to determine which logical interface a packet arrived absent a
      one-to-one correspondence between logical and physical interfaces.

5.3.12 State Changes

   During router operation, interfaces may fail or be manually disabled,
   or may become available for use by the router.  Similarly, forwarding
   may be disabled for a particular interface or for the entire router
   or may be (re)enabled.  While such transitions are (usually)
   uncommon, it is important that routers handle them correctly.

5.3.12.1 When a Router Ceases Forwarding

   When a router ceases forwarding it MUST stop advertising all routes,
   except for third party routes.  It MAY continue to receive and use
   routes from other routers in its routing domains.  If the forwarding
   database is retained, the router MUST NOT cease timing the routes in
   the forwarding database.  If routes that have been received from
   other routers are remembered, the router MUST NOT cease timing the
   routes that it has remembered.  It MUST discard any routes whose
   timers expire while forwarding is disabled, just as it would do if
   forwarding were enabled.

   DISCUSSION
      When a router ceases forwarding, it essentially ceases being a
      router.  It is still a host, and must follow all of the
      requirements of Host Requirements [INTRO:2].  The router may still
      be a passive member of one or more routing domains, however.  As
      such, it is allowed to maintain its forwarding database by
      listening to other routers in its routing domain.  It may not,
      however, advertise any of the routes in its forwarding database,
      since it itself is doing no forwarding.  The only exception to
      this rule is when the router is advertising a route that uses only



Baker                       Standards Track                    [Page 99]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


      some other router, but which this router has been asked to
      advertise.

   A router MAY send ICMP destination unreachable (host unreachable)
   messages to the senders of packets that it is unable to forward.  It
   SHOULD NOT send ICMP redirect messages.

   DISCUSSION
      Note that sending an ICMP destination unreachable (host
      unreachable) is a router action.  This message should not be sent
      by hosts.  This exception to the rules for hosts is allowed so
      that packets may be rerouted in the shortest possible time, and so
      that black holes are avoided.

5.3.12.2 When a Router Starts Forwarding

   When a router begins forwarding, it SHOULD expedite the sending of
   new routing information to all routers with which it normally
   exchanges routing information.

5.3.12.3 When an Interface Fails or is Disabled

   If an interface fails or is disabled a router MUST remove and stop
   advertising all routes in its forwarding database that make use of
   that interface.  It MUST disable all static routes that make use of
   that interface.  If other routes to the same destination and TOS are
   learned or remembered by the router, the router MUST choose the best
   alternate, and add it to its forwarding database.  The router SHOULD
   send ICMP destination unreachable or ICMP redirect messages, as
   appropriate, in reply to all packets that it is unable to forward due
   to the interface being unavailable.

5.3.12.4 When an Interface is Enabled

   If an interface that had not been available becomes available, a
   router MUST reenable any static routes that use that interface.  If
   routes that would use that interface are learned by the router, then
   these routes MUST be evaluated along with all the other learned
   routes, and the router MUST make a decision as to which routes should
   be placed in the forwarding database.  The implementor is referred to
   Chapter [7], Application Layer - Routing Protocols for further
   information on how this decision is made.

   A router SHOULD expedite the sending of new routing information to
   all routers with which it normally exchanges routing information.






Baker                       Standards Track                   [Page 100]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


5.3.13 IP Options

   Several options, such as Record Route and Timestamp, contain slots
   into which a router inserts its address when forwarding the packet.
   However, each such option has a finite number of slots, and therefore
   a router may find that there is not free slot into which it can
   insert its address.  No requirement listed below should be construed
   as requiring a router to insert its address into an option that has
   no remaining slot to insert it into.  Section [5.2.5] discusses how a
   router must choose which of its addresses to insert into an option.

5.3.13.1 Unrecognized Options Unrecognized IP options in forwarded
   packets MUST be passed through unchanged.

5.3.13.2 Security Option

   Some environments require the Security option in every packet; such a
   requirement is outside the scope of this document and the IP standard
   specification.  Note, however, that the security options described in
   [INTERNET:1] and [INTERNET:16] are obsolete.  Routers SHOULD
   IMPLEMENT the revised security option described in [INTERNET:5].

   DISCUSSION
      Routers intended for use in networks with multiple security levels
      should support packet filtering based on IPSO (RFC-1108) labels.
      To implement this support, the router would need to permit the
      router administrator to configure both a lower sensitivity limit
      (e.g. Unclassified) and an upper sensitivity limit (e.g. Secret)
      on each interface.  It is commonly but not always the case that
      the two limits are the same (e.g. a single-level interface).
      Packets caught by an IPSO filter as being out of range should be
      silently dropped and a counter should note the number of packets
      dropped because of out of range IPSO labels.

5.3.13.3 Stream Identifier Option

   This option is obsolete.  If the Stream Identifier option is present
   in a packet forwarded by the router, the option MUST be ignored and
   passed through unchanged.

5.3.13.4 Source Route Options

   A router MUST implement support for source route options in forwarded
   packets.  A router MAY implement a configuration option that, when
   enabled, causes all source-routed packets to be discarded.  However,
   such an option MUST NOT be enabled by default.





Baker                       Standards Track                   [Page 101]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   DISCUSSION
      The ability to source route datagrams through the Internet is
      important to various network diagnostic tools.  However, source
      routing may be used to bypass administrative and security controls
      within a network.  Specifically, those cases where manipulation of
      routing tables is used to provide administrative separation in
      lieu of other methods such as packet filtering may be vulnerable
      through source routed packets.

   EDITORS+COMMENTS
      Packet filtering can be defeated by source routing as well, if it
      is applied in any router except one on the final leg of the source
      routed path.  Neither route nor packet filters constitute a
      complete solution for security.

5.3.13.5 Record Route Option

   Routers MUST support the Record Route option in forwarded packets.

   A router MAY provide a configuration option that, if enabled, will
   cause the router to ignore (i.e., pass through unchanged) Record
   Route options in forwarded packets.  If provided, such an option MUST
   default to enabling the record-route.  This option should not affect
   the processing of Record Route options in datagrams received by the
   router itself (in particular, Record Route options in ICMP echo
   requests will still be processed according to Section [4.3.3.6]).

   DISCUSSION
      There are some people who believe that Record Route is a security
      problem because it discloses information about the topology of the
      network.  Thus, this document allows it to be disabled.

5.3.13.6 Timestamp Option

   Routers MUST support the timestamp option in forwarded packets.  A
   timestamp value MUST follow the rules given [INTRO:2].

   If the flags field = 3 (timestamp and prespecified address), the
   router MUST add its timestamp if the next prespecified address
   matches any of the router's IP addresses.  It is not necessary that
   the prespecified address be either the address of the interface on
   which the packet arrived or the address of the interface over which
   it will be sent.

   IMPLEMENTATION
      To maximize the utility of the timestamps contained in the
      timestamp option, it is suggested that the timestamp inserted be,
      as nearly as practical, the time at which the packet arrived at



Baker                       Standards Track                   [Page 102]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


      the router.  For datagrams originated by the router, the timestamp
      inserted should be, as nearly as practical, the time at which the
      datagram was passed to the network layer for transmission.

   A router MAY provide a configuration option which, if enabled, will
   cause the router to ignore (i.e., pass through unchanged) Timestamp
   options in forwarded datagrams when the flag word is set to zero
   (timestamps only) or one (timestamp and registering IP address).  If
   provided, such an option MUST default to off (that is, the router
   does not ignore the timestamp).  This option should not affect the
   processing of Timestamp options in datagrams received by the router
   itself (in particular, a router will insert timestamps into Timestamp
   options in datagrams received by the router, and Timestamp options in
   ICMP echo requests will still be processed according to Section
   [4.3.3.6]).

   DISCUSSION
      Like the Record Route option, the Timestamp option can reveal
      information about a network's topology.  Some people consider this
      to be a security concern.

6. TRANSPORT LAYER

   A router is not required to implement any Transport Layer protocols
   except those required to support Application Layer protocols
   supported by the router.  In practice, this means that most routers
   implement both the Transmission Control Protocol (TCP) and the User
   Datagram Protocol (UDP).

6.1 USER DATAGRAM PROTOCOL - UDP

   The User Datagram Protocol (UDP) is specified in [TRANS:1].

   A router that implements UDP MUST be compliant, and SHOULD be
   unconditionally compliant, with the requirements of [INTRO:2], except
   that:

   o This specification does not specify the interfaces between the
      various protocol layers.  Thus, a router's interfaces need not
      comply with [INTRO:2], except where compliance is required for
      proper functioning of Application Layer protocols supported by the
      router.

   o Contrary to [INTRO:2], an application SHOULD NOT disable generation
      of UDP checksums.






Baker                       Standards Track                   [Page 103]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   DISCUSSION
      Although a particular application protocol may require that UDP
      datagrams it receives must contain a UDP checksum, there is no
      general requirement that received UDP datagrams contain UDP
      checksums.  Of course, if a UDP checksum is present in a received
      datagram, the checksum must be verified and the datagram discarded
      if the checksum is incorrect.

6.2 TRANSMISSION CONTROL PROTOCOL - TCP

   The Transmission Control Protocol (TCP) is specified in [TRANS:2].

   A router that implements TCP MUST be compliant, and SHOULD be
   unconditionally compliant, with the requirements of [INTRO:2], except
   that:

   o This specification does not specify the interfaces between the
      various protocol layers.  Thus, a router need not comply with the
      following requirements of [INTRO:2] (except of course where
      compliance is required for proper functioning of Application Layer
      protocols supported by the router):

      Use of Push: RFC-793 Section 2.8:
           Passing a received PSH flag to the application layer is now
           OPTIONAL.

      Urgent Pointer: RFC-793 Section 3.1:
           A TCP MUST inform the application layer asynchronously
           whenever it receives an Urgent pointer and there was
           previously no pending urgent data, or whenever the Urgent
           pointer advances in the data stream.  There MUST be a way for
           the application to learn how much urgent data remains to be
           read from the connection, or at least to determine whether or
           not more urgent data remains to be read.

      TCP Connection Failures:
           An application MUST be able to set the value for R2 for a
           particular connection.  For example, an interactive
           application might set R2 to ``infinity,'' giving the user
           control over when to disconnect.

      TCP Multihoming:
           If an application on a multihomed host does not specify the
           local IP address when actively opening a TCP connection, then
           the TCP MUST ask the IP layer to select a local IP address
           before sending the (first) SYN.  See the function
           GET_SRCADDR() in Section 3.4.




Baker                       Standards Track                   [Page 104]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


      IP Options:
           An application MUST be able to specify a source route when it
           actively opens a TCP connection, and this MUST take
           precedence over a source route received in a datagram.

   o For similar reasons, a router need not comply with any of the
      requirements of [INTRO:2].

   o The requirements concerning the Maximum Segment Size Option in
      [INTRO:2] are amended as follows: a router that implements the
      host portion of MTU discovery (discussed in Section [4.2.3.3] of
      this memo) uses 536 as the default value of SendMSS only if the
      path MTU is unknown; if the path MTU is known, the default value
      for SendMSS is the path MTU - 40.

   o The requirements concerning the Maximum Segment Size Option in
      [INTRO:2] are amended as follows: ICMP Destination Unreachable
      codes 11 and 12 are additional soft error conditions.  Therefore,
      these message MUST NOT cause TCP to abort a connection.

   DISCUSSION
      It should particularly be noted that a TCP implementation in a
      router must conform to the following requirements of [INTRO:2]:

      o Providing a configurable TTL.  [Time to Live: RFC-793 Section
         3.9]

      o Providing an interface to configure keep-alive behavior, if
         keep-alives are used at all.  [TCP Keep-Alives]

      o Providing an error reporting mechanism, and the ability to
         manage it.  [Asynchronous Reports]

      o Specifying type of service.  [Type-of-Service]

      The general paradigm applied is that if a particular interface is
      visible outside the router, then all requirements for the
      interface must be followed.  For example, if a router provides a
      telnet function, then it will be generating traffic, likely to be
      routed in the external networks.  Therefore, it must be able to
      set the type of service correctly or else the telnet traffic may
      not get through.









Baker                       Standards Track                   [Page 105]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


7. APPLICATION LAYER - ROUTING PROTOCOLS

7.1 INTRODUCTION

   For technical, managerial, and sometimes political reasons, the
   Internet routing system consists of two components - interior routing
   and exterior routing.  The concept of an Autonomous System (AS), as
   define in Section 2.2.4 of this document, plays a key role in
   separating interior from an exterior routing, as this concept allows
   to deliniate the set of routers where a change from interior to
   exterior routing occurs.  An IP datagram may have to traverse the
   routers of two or more Autonomous Systems to reach its destination,
   and the Autonomous Systems must provide each other with topology
   information to allow such forwarding.  Interior gateway protocols
   (IGPs) are used to distribute routing information within an AS (i.e.,
   intra-AS routing).  Exterior gateway protocols are used to exchange
   routing information among ASs (i.e., inter-AS routing).

7.1.1 Routing Security Considerations

   Routing is one of the few places where the Robustness Principle (be
   liberal in what you accept) does not apply.  Routers should be
   relatively suspicious in accepting routing data from other routing
   systems.

   A router SHOULD provide the ability to rank routing information
   sources from most trustworthy to least trustworthy and to accept
   routing information about any particular destination from the most
   trustworthy sources first.  This was implicit in the original
   core/stub autonomous system routing model using EGP and various
   interior routing protocols.  It is even more important with the
   demise of a central, trusted core.

   A router SHOULD provide a mechanism to filter out obviously invalid
   routes (such as those for net 127).

   Routers MUST NOT by default redistribute routing data they do not
   themselves use, trust or otherwise consider valid.  In rare cases, it
   may be necessary to redistribute suspicious information, but this
   should only happen under direct intercession by some human agency.

   Routers must be at least a little paranoid about accepting routing
   data from anyone, and must be especially careful when they distribute
   routing information provided to them by another party.  See below for
   specific guidelines.






Baker                       Standards Track                   [Page 106]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


7.1.2 Precedence

   Except where the specification for a particular routing protocol
   specifies otherwise, a router SHOULD set the IP Precedence value for
   IP datagrams carrying routing traffic it originates to 6
   (INTERNETWORK CONTROL).

   DISCUSSION
      Routing traffic with VERY FEW exceptions should be the highest
      precedence traffic on any network.  If a system's routing traffic
      can't get through, chances are nothing else will.

7.1.3 Message Validation

   Peer-to-peer authentication involves several tests.  The application
   of message passwords and explicit acceptable neighbor lists has in
   the past improved the robustness of the route database.  Routers
   SHOULD IMPLEMENT management controls that enable explicit listing of
   valid routing neighbors.  Routers SHOULD IMPLEMENT peer-to-peer
   authentication for those routing protocols that support them.

   Routers SHOULD validate routing neighbors based on their source
   address and the interface a message is received on; neighbors in a
   directly attached subnet SHOULD be restricted to communicate with the
   router via the interface that subnet is posited on or via unnumbered
   interfaces.  Messages received on other interfaces SHOULD be silently
   discarded.

   DISCUSSION
      Security breaches and numerous routing problems are avoided by
      this basic testing.

7.2 INTERIOR GATEWAY PROTOCOLS

7.2.1 INTRODUCTION

   An Interior Gateway Protocol (IGP) is used to distribute routing
   information between the various routers in a particular AS.
   Independent of the algorithm used to implement a particular IGP, it
   should perform the following functions:

   (1) Respond quickly to changes in the internal topology of an AS

   (2) Provide a mechanism such that circuit flapping does not cause
        continuous routing updates

   (3) Provide quick convergence to loop-free routing




Baker                       Standards Track                   [Page 107]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   (4) Utilize minimal bandwidth

   (5) Provide equal cost routes to enable load-splitting

   (6) Provide a means for authentication of routing updates

   Current IGPs used in the internet today are characterized as either
   being based on a distance-vector or a link-state algorithm.

   Several IGPs are detailed in this section, including those most
   commonly used and some recently developed protocols that may be
   widely used in the future.  Numerous other protocols intended for use
   in intra-AS routing exist in the Internet community.

   A router that implements any routing protocol (other than static
   routes) MUST IMPLEMENT OSPF (see Section [7.2.2]).  A router MAY
   implement additional IGPs.

7.2.2 OPEN SHORTEST PATH FIRST - OSPF

   Shortest Path First (SPF) based routing protocols are a class of
   link-state algorithms that are based on the shortest-path algorithm
   of Dijkstra.  Although SPF based algorithms have been around since
   the inception of the ARPANET, it is only recently that they have
   achieved popularity both inside both the IP and the OSI communities.
   In an SPF based system, each router obtains the entire topology
   database through a process known as flooding.  Flooding insures a
   reliable transfer of the information.  Each router then runs the SPF
   algorithm on its database to build the IP routing table.  The OSPF
   routing protocol is an implementation of an SPF algorithm.  The
   current version, OSPF version 2, is specified in [ROUTE:1].  Note
   that RFC-1131, which describes OSPF version 1, is obsolete.

   Note that to comply with Section [8.3] of this memo, a router that
   implements OSPF MUST implement the OSPF MIB [MGT:14].

7.2.3 INTERMEDIATE SYSTEM TO INTERMEDIATE SYSTEM - DUAL IS-IS

   The American National Standards Institute (ANSI) X3S3.3 committee has
   defined an intra-domain routing protocol.  This protocol is titled
   Intermediate System to Intermediate System Routeing Exchange
   Protocol.

   Its application to an IP network has been defined in [ROUTE:2], and
   is referred to as Dual IS-IS (or sometimes as Integrated IS-IS).
   IS-IS is based on a link-state (SPF) routing algorithm and shares all
   the advantages for this class of protocols.




Baker                       Standards Track                   [Page 108]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


7.3  EXTERIOR GATEWAY PROTOCOLS

7.3.1  INTRODUCTION

   Exterior Gateway Protocols are utilized for inter-Autonomous System
   routing to exchange reachability information for a set of networks
   internal to a particular autonomous system to a neighboring
   autonomous system.

   The area of inter-AS routing is a current topic of research inside
   the Internet Engineering Task Force.  The Exterior Gateway Protocol
   (EGP) described in Section [Appendix F.1] has traditionally been the
   inter-AS protocol of choice, but is now historical.  The Border
   Gateway Protocol (BGP) eliminates many of the restrictions and
   limitations of EGP, and is therefore growing rapidly in popularity.
   A router is not required to implement any inter-AS routing protocol.
   However, if a router does implement EGP it also MUST IMPLEMENT BGP.
   Although it was not designed as an exterior gateway protocol, RIP
   (described in Section [7.2.4]) is sometimes used for inter-AS
   routing.

7.3.2 BORDER GATEWAY PROTOCOL - BGP

7.3.2.1 Introduction

   The Border Gateway Protocol (BGP-4) is an inter-AS routing protocol
   that exchanges network reachability information with other BGP
   speakers.  The information for a network includes the complete list
   of ASs that traffic must transit to reach that network.  This
   information can then be used to insure loop-free paths.  This
   information is sufficient to construct a graph of AS connectivity
   from which routing loops may be pruned and some policy decisions at
   the AS level may be enforced.

   BGP is defined by [ROUTE:4].  [ROUTE:5] specifies the proper usage of
   BGP in the Internet, and provides some useful implementation hints
   and guidelines.  [ROUTE:12] and [ROUTE:13] provide additional useful
   information.

   To comply with Section [8.3] of this memo, a router that implements
   BGP is required to implement the BGP MIB [MGT:15].

   To characterize the set of policy decisions that can be enforced
   using BGP, one must focus on the rule that an AS advertises to its
   neighbor ASs only those routes that it itself uses.  This rule
   reflects the hop-by-hop routing paradigm generally used throughout
   the current Internet.  Note that some policies cannot be supported by
   the hop-by-hop routing paradigm and thus require techniques such as



Baker                       Standards Track                   [Page 109]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   source routing to enforce.  For example, BGP does not enable one AS
   to send traffic to a neighbor AS intending that traffic take a
   different route from that taken by traffic originating in the
   neighbor AS.  On the other hand, BGP can support any policy
   conforming to the hop-by-hop routing paradigm.

   Implementors of BGP are strongly encouraged to follow the
   recommendations outlined in Section 6 of [ROUTE:5].

7.3.2.2 Protocol Walk-through

   While BGP provides support for quite complex routing policies (as an
   example see Section 4.2 in [ROUTE:5]), it is not required for all BGP
   implementors to support such policies.  At a minimum, however, a BGP
   implementation:

   (1) SHOULD allow an AS to control announcements of the BGP learned
        routes to adjacent AS's.  Implementations SHOULD support such
        control with at least the granularity of a single network.
        Implementations SHOULD also support such control with the
        granularity of an autonomous system, where the autonomous system
        may be either the autonomous system that originated the route,
        or the autonomous system that advertised the route to the local
        system (adjacent autonomous system).

   (2) SHOULD allow an AS to prefer a particular path to a destination
        (when more than one path is available).  Such function SHOULD be
        implemented by allowing system administrator to assign weights
        to Autonomous Systems, and making route selection process to
        select a route with the lowest weight (where weight of a route
        is defined as a sum of weights of all AS's in the AS_PATH path
        attribute associated with that route).

   (3) SHOULD allow an AS to ignore routes with certain AS's in the
        AS_PATH path attribute.  Such function can be implemented by
        using technique outlined in (2), and by assigning infinity as
        weights for such AS's.  The route selection process must ignore
        routes that have weight equal to infinity.

7.3.3 INTER-AS ROUTING WITHOUT AN EXTERIOR PROTOCOL

   It is possible to exchange routing information between two autonomous
   systems or routing domains without using a standard exterior routing
   protocol between two separate, standard interior routing protocols.
   The most common way of doing this is to run both interior protocols
   independently in one of the border routers with an exchange of route
   information between the two processes.




Baker                       Standards Track                   [Page 110]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   As with the exchange of information from an EGP to an IGP, without
   appropriate controls these exchanges of routing information between
   two IGPs in a single router are subject to creation of routing loops.

7.4 STATIC ROUTING

   Static routing provides a means of explicitly defining the next hop
   from a router for a particular destination.  A router SHOULD provide
   a means for defining a static route to a destination, where the
   destination is defined by a network prefix.  The mechanism SHOULD
   also allow for a metric to be specified for each static route.

   A router that supports a dynamic routing protocol MUST allow static
   routes to be defined with any metric valid for the routing protocol
   used.  The router MUST provide the ability for the user to specify a
   list of static routes that may or may not be propagated through the
   routing protocol.  In addition, a router SHOULD support the following
   additional information if it supports a routing protocol that could
   make use of the information.  They are:

   o TOS,

   o Subnet Mask, or

   o Prefix Length, or

   o A metric specific to a given routing protocol that can import the
      route.

   DISCUSSION
      We intend that one needs to support only the things useful to the
      given routing protocol.  The need for TOS should not require the
      vendor to implement the other parts if they are not used.

      Whether a router prefers a static route over a dynamic route (or
      vice versa) or whether the associated metrics are used to choose
      between conflicting static and dynamic routes SHOULD be
      configurable for each static route.

      A router MUST allow a metric to be assigned to a static route for
      each routing domain that it supports.  Each such metric MUST be
      explicitly assigned to a specific routing domain.  For example:

           route 10.0.0.0/8 via 192.0.2.3 rip metric 3

           route 10.21.0.0/16 via 192.0.2.4 ospf inter-area metric 27

           route 10.22.0.0/16 via 192.0.2.5 egp 123 metric 99



Baker                       Standards Track                   [Page 111]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   DISCUSSION
      It has been suggested that, ideally, static routes should have
      preference values rather than metrics (since metrics can only be
      compared with metrics of other routes in the same routing domain,
      the metric of a static route could only be compared with metrics
      of other static routes).  This is contrary to some current
      implementations, where static routes really do have metrics, and
      those metrics are used to determine whether a particular dynamic
      route overrides the static route to the same destination.  Thus,
      this document uses the term metric rather than preference.

      This technique essentially makes the static route into a RIP
      route, or an OSPF route (or whatever, depending on the domain of
      the metric).  Thus, the route lookup algorithm of that domain
      applies.  However, this is NOT route leaking, in that coercing a
      static route into a dynamic routing domain does not authorize the
      router to redistribute the route into the dynamic routing domain.

      For static routes not put into a specific routing domain, the
      route lookup algorithm is:

      (1) Basic match

      (2) Longest match

      (3) Weak TOS (if TOS supported)

      (4) Best metric (where metric are implementation-defined)

      The last step may not be necessary, but it's useful in the case
      where you want to have a primary static route over one interface
      and a secondary static route over an alternate interface, with
      failover to the alternate path if the interface for the primary
      route fails.

7.5 FILTERING OF ROUTING INFORMATION

   Each router within a network makes forwarding decisions based upon
   information contained within its forwarding database.  In a simple
   network the contents of the database may be configured statically.
   As the network grows more complex, the need for dynamic updating of
   the forwarding database becomes critical to the efficient operation
   of the network.

   If the data flow through a network is to be as efficient as possible,
   it is necessary to provide a mechanism for controlling the
   propagation of the information a router uses to build its forwarding
   database.  This control takes the form of choosing which sources of



Baker                       Standards Track                   [Page 112]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   routing information should be trusted and selecting which pieces of
   the information to believe.  The resulting forwarding database is a
   filtered version of the available routing information.

   In addition to efficiency, controlling the propagation of routing
   information can reduce instability by preventing the spread of
   incorrect or bad routing information.

   In some cases local policy may require that complete routing
   information not be widely propagated.

   These filtering requirements apply only to non-SPF-based protocols
   (and therefore not at all to routers which don't implement any
   distance vector protocols).

7.5.1 Route Validation

   A router SHOULD log as an error any routing update advertising a
   route that violates the specifications of this memo, unless the
   routing protocol from which the update was received uses those values
   to encode special routes (such as default routes).

7.5.2 Basic Route Filtering

   Filtering of routing information allows control of paths used by a
   router to forward packets it receives.  A router should be selective
   in which sources of routing information it listens to and what routes
   it believes.  Therefore, a router MUST provide the ability to
   specify:

   o On which logical interfaces routing information will be accepted
      and which routes will be accepted from each logical interface.

   o Whether all routes or only a default route is advertised on a
      logical interface.

   Some routing protocols do not recognize logical interfaces as a
   source of routing information.  In such cases the router MUST provide
   the ability to specify

   o from which other routers routing information will be accepted.

   For example, assume a router connecting one or more leaf networks to
   the main portion or backbone of a larger network.  Since each of the
   leaf networks has only one path in and out, the router can simply
   send a default route to them.  It advertises the leaf networks to the
   main network.




Baker                       Standards Track                   [Page 113]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


7.5.3 Advanced Route Filtering

   As the topology of a network grows more complex, the need for more
   complex route filtering arises.  Therefore, a router SHOULD provide
   the ability to specify independently for each routing protocol:

   o Which logical interfaces or routers routing information (routes)
      will be accepted from and which routes will be believed from each
      other router or logical interface,

   o Which routes will be sent via which logical interface(s), and

   o Which routers routing information will be sent to, if this is
      supported by the routing protocol in use.

   In many situations it is desirable to assign a reliability ordering
   to routing information received from another router instead of the
   simple believe or don't believe choice listed in the first bullet
   above.  A router MAY provide the ability to specify:

   o A reliability or preference to be assigned to each route received.
      A route with higher reliability will be chosen over one with lower
      reliability regardless of the routing metric associated with each
      route.

   If a router supports assignment of preferences, the router MUST NOT
   propagate any routes it does not prefer as first party information.
   If the routing protocol being used to propagate the routes does not
   support distinguishing between first and third party information, the
   router MUST NOT propagate any routes it does not prefer.

   DISCUSSION
      For example, assume a router receives a route to network C from
      router R and a route to the same network from router S.  If router
      R is considered more reliable than router S traffic destined for
      network C will be forwarded to router R regardless of the route
      received from router S.

   Routing information for routes which the router does not use (router
   S in the above example) MUST NOT be passed to any other router.

7.6 INTER-ROUTING-PROTOCOL INFORMATION EXCHANGE

   Routers MUST be able to exchange routing information between separate
   IP interior routing protocols, if independent IP routing processes
   can run in the same router.  Routers MUST provide some mechanism for
   avoiding routing loops when routers are configured for bi-directional
   exchange of routing information between two separate interior routing



Baker                       Standards Track                   [Page 114]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   processes.  Routers MUST provide some priority mechanism for choosing
   routes from independent routing processes.  Routers SHOULD provide
   administrative control of IGP-IGP exchange when used across
   administrative boundaries.

   Routers SHOULD provide some mechanism for translating or transforming
   metrics on a per network basis.  Routers (or routing protocols) MAY
   allow for global preference of exterior routes imported into an IGP.

   DISCUSSION
      Different IGPs use different metrics, requiring some translation
      technique when introducing information from one protocol into
      another protocol with a different form of metric.  Some IGPs can
      run multiple instances within the same router or set of routers.
      In this case metric information can be preserved exactly or
      translated.

      There are at least two techniques for translation between
      different routing processes.  The static (or reachability)
      approach uses the existence of a route advertisement in one IGP to
      generate a route advertisement in the other IGP with a given
      metric.  The translation or tabular approach uses the metric in
      one IGP to create a metric in the other IGP through use of either
      a function (such as adding a constant) or a table lookup.

      Bi-directional exchange of routing information is dangerous
      without control mechanisms to limit feedback.  This is the same
      problem that distance vector routing protocols must address with
      the split horizon technique and that EGP addresses with the
      third-party rule.  Routing loops can be avoided explicitly through
      use of tables or lists of permitted/denied routes or implicitly
      through use of a split horizon rule, a no-third-party rule, or a
      route tagging mechanism.  Vendors are encouraged to use implicit
      techniques where possible to make administration easier for
      network operators.

8. APPLICATION LAYER - NETWORK MANAGEMENT PROTOCOLS

   Note that this chapter supersedes any requirements stated under
   "REMOTE MANAGEMENT" in [INTRO:3].

8.1 The Simple Network Management Protocol - SNMP

8.1.1 SNMP Protocol Elements

   Routers MUST be manageable by SNMP [MGT:3].  The SNMP MUST operate
   using UDP/IP as its transport and network protocols.  Others MAY be
   supported (e.g., see [MGT:25, MGT:26, MGT:27, and MGT:28]).  SNMP



Baker                       Standards Track                   [Page 115]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   management operations MUST operate as if the SNMP was implemented on
   the router itself.  Specifically, management operations MUST be
   effected by sending SNMP management requests to any of the IP
   addresses assigned to any of the router's interfaces.  The actual
   management operation may be performed either by the router or by a
   proxy for the router.

   DISCUSSION
      This wording is intended to allow management either by proxy,
      where the proxy device responds to SNMP packets that have one of
      the router's IP addresses in the packets destination address
      field, or the SNMP is implemented directly in the router itself
      and receives packets and responds to them in the proper manner.

      It is important that management operations can be sent to one of
      the router's IP Addresses.  In diagnosing network problems the
      only thing identifying the router that is available may be one of
      the router's IP address; obtained perhaps by looking through
      another router's routing table.

   All SNMP operations (get, get-next, get-response, set, and trap) MUST
   be implemented.

   Routers MUST provide a mechanism for rate-limiting the generation of
   SNMP trap messages.  Routers MAY provide this mechanism through the
   algorithms for asynchronous alert management described in [MGT:5].

   DISCUSSION
      Although there is general agreement about the need to rate-limit
      traps, there is not yet consensus on how this is best achieved.
      The reference cited is considered experimental.

8.2 Community Table

   For the purposes of this specification, we assume that there is an
   abstract `community table' in the router.  This table contains
   several entries, each entry for a specific community and containing
   the parameters necessary to completely define the attributes of that
   community.  The actual implementation method of the abstract
   community table is, of course, implementation specific.

   A router's community table MUST allow for at least one entry and
   SHOULD allow for at least two entries.

   DISCUSSION
      A community table with zero capacity is useless.  It means that
      the router will not recognize any communities and, therefore, all
      SNMP operations will be rejected.



Baker                       Standards Track                   [Page 116]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


      Therefore, one entry is the minimal useful size of the table.
      Having two entries allows one entry to be limited to read-only
      access while the other would have write capabilities.

   Routers MUST allow the user to manually (i.e., without using SNMP)
   examine, add, delete and change entries in the SNMP community table.
   The user MUST be able to set the community name or construct a MIB
   view.  The user MUST be able to configure communities as read-only
   (i.e., they do not allow SETs) or read-write (i.e., they do allow
   SETs).

   The user MUST be able to define at least one IP address to which
   notifications are sent for each community or MIB view, if traps are
   used.  These addresses SHOULD be definable on a community or MIB view
   basis.  It SHOULD be possible to enable or disable notifications on a
   community or MIB view basis.

   A router SHOULD provide the ability to specify a list of valid
   network managers for any particular community.  If enabled, a router
   MUST validate the source address of the SNMP datagram against the
   list and MUST discard the datagram if its address does not appear.
   If the datagram is discarded the router MUST take all actions
   appropriate to an SNMP authentication failure.

   DISCUSSION
      This is a rather limited authentication system, but coupled with
      various forms of packet filtering may provide some small measure
      of increased security.

   The community table MUST be saved in non-volatile storage.

   The initial state of the community table SHOULD contain one entry,
   with the community name string public and read-only access.  The
   default state of this entry MUST NOT send traps.  If it is
   implemented, then this entry MUST remain in the community table until
   the administrator changes it or deletes it.

   DISCUSSION
      By default, traps are not sent to this community.  Trap PDUs are
      sent to unicast IP addresses.  This address must be configured
      into the router in some manner.  Before the configuration occurs,
      there is no such address, so to whom should the trap be sent?
      Therefore trap sending to the public community defaults to be
      disabled.  This can, of course, be changed by an administrative
      operation once the router is operational.






Baker                       Standards Track                   [Page 117]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


8.3 Standard MIBS

   All MIBS relevant to a router's configuration are to be implemented.
   To wit:

   o The System, Interface, IP, ICMP, and UDP groups of MIB-II [MGT:2]
      MUST be implemented.

   o The Interface Extensions MIB [MGT:18] MUST be implemented.

   o The IP Forwarding Table MIB [MGT:20] MUST be implemented.

   o If the router implements TCP (e.g., for Telnet) then the TCP group
      of MIB-II [MGT:2] MUST be implemented.

   o If the router implements EGP then the EGP group of MIB-II [MGT:2]
      MUST be implemented.

   o If the router supports OSPF then the OSPF MIB [MGT:14] MUST be
      implemented.

   o If the router supports BGP then the BGP MIB [MGT:15] MUST be
      implemented.

   o If the router has Ethernet, 802.3, or StarLan interfaces then the
      Ethernet-Like MIB [MGT:6] MUST be implemented.

   o If the router has 802.4 interfaces then the 802.4 MIB [MGT:7] MUST
      be implemented.

   o If the router has 802.5 interfaces then the 802.5 MIB [MGT:8] MUST
      be implemented.

   o If the router has FDDI interfaces that implement ANSI SMT 7.3 then
      the FDDI MIB [MGT:9] MUST be implemented.

   o If the router has FDDI interfaces that implement ANSI SMT 6.2 then
      the FDDI MIB [MGT:29] MUST be implemented.

   o If the router has interfaces that use V.24 signalling, such as RS-
      232, V.10, V.11, V.35, V.36, or RS-422/423/449, then the RS-232
      [MGT:10] MIB MUST be implemented.

   o If the router has T1/DS1 interfaces then the T1/DS1 MIB [MGT:16]
      MUST be implemented.

   o If the router has T3/DS3 interfaces then the T3/DS3 MIB [MGT:17]
      MUST be implemented.



Baker                       Standards Track                   [Page 118]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   o If the router has SMDS interfaces then the SMDS Interface Protocol
      MIB [MGT:19] MUST be implemented.

   o If the router supports PPP over any of its interfaces then the PPP
      MIBs [MGT:11], [MGT:12], and [MGT:13] MUST be implemented.

   o If the router supports RIP Version 2 then the RIP Version 2 MIB
      [MGT:21] MUST be implemented.

   o If the router supports X.25 over any of its interfaces then the
      X.25 MIBs [MGT:22, MGT:23 and MGT:24] MUST be implemented.

8.4 Vendor Specific MIBS

   The Internet Standard and Experimental MIBs do not cover the entire
   range of statistical, state, configuration and control information
   that may be available in a network element.  This information is,
   nevertheless, extremely useful.  Vendors of routers (and other
   network devices) generally have developed MIB extensions that cover
   this information.  These MIB extensions are called Vendor Specific
   MIBs.

   The Vendor Specific MIB for the router MUST provide access to all
   statistical, state, configuration, and control information that is
   not available through the Standard and Experimental MIBs that have
   been implemented.  This information MUST be available for both
   monitoring and control operations.

   DISCUSSION
      The intent of this requirement is to provide the ability to do
      anything on the router through SNMP that can be done through a
      console, and vice versa.  A certain minimal amount of
      configuration is necessary before SNMP can operate (e.g., the
      router must have an IP address).  This initial configuration can
      not be done through SNMP.  However, once the initial configuration
      is done, full capabilities ought to be available through network
      management.

   The vendor SHOULD make available the specifications for all Vendor
   Specific MIB variables.  These specifications MUST conform to the SMI
   [MGT:1] and the descriptions MUST be in the form specified in
   [MGT:4].

   DISCUSSION
      Making the Vendor Specific MIB available to the user is necessary.
      Without this information the users would not be able to configure
      their network management systems to be able to access the Vendor
      Specific parameters.  These parameters would then be useless.



Baker                       Standards Track                   [Page 119]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


      ne 2 The format of the MIB specification is also specified.
      Parsers that read MIB specifications and generate the needed
      tables for the network management station are available.  These
      parsers generally understand only the standard MIB specification
      format.

8.5 Saving Changes

   Parameters altered by SNMP MAY be saved to non-volatile storage.

   DISCUSSION
      Reasons why this requirement is a MAY:

      o The exact physical nature of non-volatile storage is not
         specified in this document.  Hence, parameters may be saved in
         NVRAM/EEPROM, local floppy or hard disk, or in some TFTP file
         server or BOOTP server, etc.  Suppose that this information is
         in a file that is retrieved through TFTP.  In that case, a
         change made to a configuration parameter on the router would
         need to be propagated back to the file server holding the
         configuration file.  Alternatively, the SNMP operation would
         need to be directed to the file server, and then the change
         somehow propagated to the router.  The answer to this problem
         does not seem obvious.

         This also places more requirements on the host holding the
         configuration information than just having an available TFTP
         server, so much more that its probably unsafe for a vendor to
         assume that any potential customer will have a suitable host
         available.

      o The timing of committing changed parameters to non-volatile
         storage is still an issue for debate.  Some prefer to commit
         all changes immediately.  Others prefer to commit changes to
         non-volatile storage only upon an explicit command.

9. APPLICATION LAYER - MISCELLANEOUS PROTOCOLS

   For all additional application protocols that a router implements,
   the router MUST be compliant and SHOULD be unconditionally compliant
   with the relevant requirements of [INTRO:3].

9.1 BOOTP

9.1.1 Introduction

   The Bootstrap Protocol (BOOTP) is a UDP/IP-based protocol that allows
   a booting host to configure itself dynamically and without user



Baker                       Standards Track                   [Page 120]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   supervision.  BOOTP provides a means to notify a host of its assigned
   IP address, the IP address of a boot server host, and the name of a
   file to be loaded into memory and executed ([APPL:1]).  Other
   configuration information such as the local prefix length or subnet
   mask, the local time offset, the addresses of default routers, and
   the addresses of various Internet servers can also be communicated to
   a host using BOOTP ([APPL:2]).

9.1.2 BOOTP Relay Agents

   In many cases, BOOTP clients and their associated BOOTP server(s) do
   not reside on the same IP (sub)network.  In such cases, a third-party
   agent is required to transfer BOOTP messages between clients and
   servers.  Such an agent was originally referred to as a BOOTP
   forwarding agent.  However, to avoid confusion with the IP forwarding
   function of a router, the name BOOTP relay agent has been adopted
   instead.

   DISCUSSION
      A BOOTP relay agent performs a task that is distinct from a
      router's normal IP forwarding function.  While a router normally
      switches IP datagrams between networks more-or-less transparently,
      a BOOTP relay agent may more properly be thought to receive BOOTP
      messages as a final destination and then generate new BOOTP
      messages as a result.  One should resist the notion of simply
      forwarding a BOOTP message straight through like a regular packet.

   This relay-agent functionality is most conveniently located in the
   routers that interconnect the clients and servers (although it may
   alternatively be located in a host that is directly connected to the
   client (sub)net).

   A router MAY provide BOOTP relay-agent capability.  If it does, it
   MUST conform to the specifications in [APPL:3].

   Section [5.2.3] discussed the circumstances under which a packet is
   delivered locally (to the router).  All locally delivered UDP
   messages whose UDP destination port number is BOOTPS (67) are
   considered for special processing by the router's logical BOOTP relay
   agent.

   Sections [4.2.2.11] and [5.3.7] discussed invalid IP source
   addresses.  According to these rules, a router must not forward any
   received datagram whose IP source address is 0.0.0.0.  However,
   routers that support a BOOTP relay agent MUST accept for local
   delivery to the relay agent BOOTREQUEST messages whose IP source
   address is 0.0.0.0.




Baker                       Standards Track                   [Page 121]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


10. OPERATIONS AND MAINTENANCE

   This chapter supersedes any requirements of [INTRO:3] relating to
   "Extensions to the IP Module."

   Facilities to support operation and maintenance (O&M) activities form
   an essential part of any router implementation.  Although these
   functions do not seem to relate directly to interoperability, they
   are essential to the network manager who must make the router
   interoperate and must track down problems when it doesn't.  This
   chapter also includes some discussion of router initialization and of
   facilities to assist network managers in securing and accounting for
   their networks.

10.1 Introduction

   The following kinds of activities are included under router O&M:

   o Diagnosing hardware problems in the router's processor, in its
      network interfaces, or in its connected networks, modems, or
      communication lines.

   o Installing new hardware

   o Installing new software.

   o Restarting or rebooting the router after a crash.

   o Configuring (or reconfiguring) the router.

   o Detecting and diagnosing Internet problems such as congestion,
      routing loops, bad IP addresses, black holes, packet avalanches,
      and misbehaved hosts.

   o Changing network topology, either temporarily (e.g., to bypass a
      communication line problem) or permanently.

   o Monitoring the status and performance of the routers and the
      connected networks.

   o Collecting traffic statistics for use in (Inter-)network planning.

   o Coordinating the above activities with appropriate vendors and
      telecommunications specialists.

   Routers and their connected communication lines are often operated as
   a system by a centralized O&M organization.  This organization may
   maintain a (Inter-)network operation center, or NOC, to carry out its



Baker                       Standards Track                   [Page 122]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   O&M functions.  It is essential that routers support remote control
   and monitoring from such a NOC through an Internet path, since
   routers might not be connected to the same network as their NOC.
   Since a network failure may temporarily preclude network access, many
   NOCs insist that routers be accessible for network management through
   an alternative means, often dial-up modems attached to console ports
   on the routers.

   Since an IP packet traversing an internet will often use routers
   under the control of more than one NOC, Internet problem diagnosis
   will often involve cooperation of personnel of more than one NOC.  In
   some cases, the same router may need to be monitored by more than one
   NOC, but only if necessary, because excessive monitoring could impact
   a router's performance.

   The tools available for monitoring at a NOC may cover a wide range of
   sophistication.  Current implementations include multi-window,
   dynamic displays of the entire router system.  The use of AI
   techniques for automatic problem diagnosis is proposed for the
   future.

   Router O&M facilities discussed here are only a part of the large and
   difficult problem of Internet management.  These problems encompass
   not only multiple management organizations, but also multiple
   protocol layers.  For example, at the current stage of evolution of
   the Internet architecture, there is a strong coupling between host
   TCP implementations and eventual IP-level congestion in the router
   system [OPER:1].  Therefore, diagnosis of congestion problems will
   sometimes require the monitoring of TCP statistics in hosts.  There
   are currently a number of R&D efforts in progress in the area of
   Internet management and more specifically router O&M.  These R&D
   efforts have already produced standards for router O&M.  This is also
   an area in which vendor creativity can make a significant
   contribution.

10.2 Router Initialization

10.2.1 Minimum Router Configuration

   There exists a minimum set of conditions that must be satisfied
   before a router may forward packets.  A router MUST NOT enable
   forwarding on any physical interface unless either:

   (1) The router knows the IP address and associated subnet mask or
        network prefix length of at least one logical interface
        associated with that physical interface, or





Baker                       Standards Track                   [Page 123]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   (2) The router knows that the interface is an unnumbered interface
        and knows its router-id.

   These parameters MUST be explicitly configured:

   o A router MUST NOT use factory-configured default values for its IP
      addresses, prefix lengths, or router-id, and

   o A router MUST NOT assume that an unconfigured interface is an
      unnumbered interface.

   DISCUSSION
      There have been instances in which routers have been shipped with
      vendor-installed default addresses for interfaces.  In a few
      cases, this has resulted in routers advertising these default
      addresses into active networks.

10.2.2 Address and Prefix Initialization

   A router MUST allow its IP addresses and their address masks or
   prefix lengths to be statically configured and saved in non-volatile
   storage.

   A router MAY obtain its IP addresses and their corresponding address
   masks dynamically as a side effect of the system initialization
   process (see Section 10.2.3]);

   If the dynamic method is provided, the choice of method to be used in
   a particular router MUST be configurable.

   As was described in Section [4.2.2.11], IP addresses are not
   permitted to have the value 0 or -1 in the  or
    fields.  Therefore, a router SHOULD NOT allow an IP
   address or address mask to be set to a value that would make any of
   the these fields above have the value zero or -1.

   DISCUSSION
      It is possible using arbitrary address masks to create situations
      in which routing is ambiguous (i.e., two routes with different but
      equally specific subnet masks match a particular destination
      address).  This is one of the strongest arguments for the use of
      network prefixes, and the reason the use of discontiguous subnet
      masks is not permitted.

   A router SHOULD make the following checks on any address mask it
   installs:





Baker                       Standards Track                   [Page 124]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   o The mask is neither all ones nor all zeroes (the prefix length is
      neither zero nor 32).

   o The bits which correspond to the network prefix part of the address
      are all set to 1.

   o The bits that correspond to the network prefix are contiguous.

   DISCUSSION
      The masks associated with routes are also sometimes called subnet
      masks, this test should not be applied to them.

10.2.3 Network Booting using BOOTP and TFTP

   There has been much discussion of how routers can and should be
   booted from the network.  These discussions have revolved around
   BOOTP and TFTP.  Currently, there are routers that boot with TFTP
   from the network.  There is no reason that BOOTP could not be used
   for locating the server that the boot image should be loaded from.

   BOOTP is a protocol used to boot end systems, and requires some
   stretching to accommodate its use with routers.  If a router is using
   BOOTP to locate the current boot host, it should send a BOOTP Request
   with its hardware address for its first interface, or, if it has been
   previously configured otherwise, with either another interface's
   hardware address, or another number to put in the hardware address
   field of the BOOTP packet.  This is to allow routers without hardware
   addresses (like synchronous line only routers) to use BOOTP for
   bootload discovery.  TFTP can then be used to retrieve the image
   found in the BOOTP Reply.  If there are no configured interfaces or
   numbers to use, a router MAY cycle through the interface hardware
   addresses it has until a match is found by the BOOTP server.

   A router SHOULD IMPLEMENT the ability to store parameters learned
   through BOOTP into local non-volatile storage.  A router MAY
   implement the ability to store a system image loaded over the network
   into local stable storage.

   A router MAY have a facility to allow a remote user to request that
   the router get a new boot image.  Differentiation should be made
   between getting the new boot image from one of three locations: the
   one included in the request, from the last boot image server, and
   using BOOTP to locate a server.








Baker                       Standards Track                   [Page 125]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


10.3 Operation and Maintenance

10.3.1 Introduction

   There is a range of possible models for performing O&M functions on a
   router.  At one extreme is the local-only model, under which the O&M
   functions can only be executed locally (e.g., from a terminal plugged
   into the router machine).  At the other extreme, the fully remote
   model allows only an absolute minimum of functions to be performed
   locally (e.g., forcing a boot), with most O&M being done remotely
   from the NOC.  There are intermediate models, such as one in which
   NOC personnel can log into the router as a host, using the Telnet
   protocol, to perform functions that can also be invoked locally.  The
   local-only model may be adequate in a few router installations, but
   remote operation from a NOC is normally required, and therefore
   remote O&M provisions are required for most routers.

   Remote O&M functions may be exercised through a control agent
   (program).  In the direct approach, the router would support remote
   O&M functions directly from the NOC using standard Internet protocols
   (e.g., SNMP, UDP or TCP); in the indirect approach, the control agent
   would support these protocols and control the router itself using
   proprietary protocols.  The direct approach is preferred, although
   either approach is acceptable.  The use of specialized host hardware
   and/or software requiring significant additional investment is
   discouraged; nevertheless, some vendors may elect to provide the
   control agent as an integrated part of the network in which the
   routers are a part.  If this is the case, it is required that a means
   be available to operate the control agent from a remote site using
   Internet protocols and paths and with equivalent functionality with
   respect to a local agent terminal.

   It is desirable that a control agent and any other NOC software tools
   that a vendor provides operate as user programs in a standard
   operating system.  The use of the standard Internet protocols UDP and
   TCP for communicating with the routers should facilitate this.

   Remote router monitoring and (especially) remote router control
   present important access control problems that must be addressed.
   Care must also be taken to ensure control of the use of router
   resources for these functions.  It is not desirable to let router
   monitoring take more than some limited fraction of the router CPU
   time, for example.  On the other hand, O&M functions must receive
   priority so they can be exercised when the router is congested, since
   often that is when O&M is most needed.






Baker                       Standards Track                   [Page 126]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


10.3.2 Out Of Band Access

   Routers MUST support Out-Of-Band (OOB) access.  OOB access SHOULD
   provide the same functionality as in-band access.  This access SHOULD
   implement access controls, to prevent unauthorized access.

   DISCUSSION
      This Out-Of-Band access will allow the NOC a way to access
      isolated routers during times when network access is not
      available.

      Out-Of-Band access is an important management tool for the network
      administrator.  It allows the access of equipment independent of
      the network connections.  There are many ways to achieve this
      access.  Whichever one is used it is important that the access is
      independent of the network connections.  An example of Out-Of-Band
      access would be a serial port connected to a modem that provides
      dial up access to the router.

      It is important that the OOB access provides the same
      functionality as in-band access.  In-band access, or accessing
      equipment through the existing network connection, is limiting,
      because most of the time, administrators need to reach equipment
      to figure out why it is unreachable.  In band access is still very
      important for configuring a router, and for troubleshooting more
      subtle problems.

10.3.2 Router O&M Functions

10.3.2.1 Maintenance - Hardware Diagnosis

   Each router SHOULD operate as a stand-alone device for the purposes
   of local hardware maintenance.  Means SHOULD be available to run
   diagnostic programs at the router site using only on-site tools.  A
   router SHOULD be able to run diagnostics in case of a fault.  For
   suggested hardware and software diagnostics see Section [10.3.3].

10.3.2.2 Control - Dumping and Rebooting

   A router MUST include both in-band and out-of-band mechanisms to
   allow the network manager to reload, stop, and restart the router.  A
   router SHOULD also contain a mechanism (such as a watchdog timer)
   which will reboot the router automatically if it hangs due to a
   software or hardware fault.

   A router SHOULD IMPLEMENT a mechanism for dumping the contents of a
   router's memory (and/or other state useful for vendor debugging after
   a crash), and either saving them on a stable storage device local to



Baker                       Standards Track                   [Page 127]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   the router or saving them on another host via an up-line dump
   mechanism such as TFTP (see [OPER:2], [INTRO:3]).

10.3.2.3 Control - Configuring the Router

   Every router has configuration parameters that may need to be set.
   It SHOULD be possible to update the parameters without rebooting the
   router; at worst, a restart MAY be required.  There may be cases when
   it is not possible to change parameters without rebooting the router
   (for instance, changing the IP address of an interface).  In these
   cases, care should be taken to minimize disruption to the router and
   the surrounding network.

   There SHOULD be a way to configure the router over the network either
   manually or automatically.  A router SHOULD be able to upload or
   download its parameters from a host or another router.  A means
   SHOULD be provided, either as an application program or a router
   function, to convert between the parameter format and a human-
   editable format.  A router SHOULD have some sort of stable storage
   for its configuration.  A router SHOULD NOT believe protocols such as
   RARP, ICMP Address Mask Reply, and MAY not believe BOOTP.

   DISCUSSION
      It is necessary to note here that in the future RARP, ICMP Address
      Mask Reply, BOOTP and other mechanisms may be needed to allow a
      router to auto-configure.  Although routers may in the future be
      able to configure automatically, the intent here is to discourage
      this practice in a production environment until auto-configuration
      has been tested more thoroughly.  The intent is NOT to discourage
      auto-configuration all together.  In cases where a router is
      expected to get its configuration automatically it may be wise to
      allow the router to believe these things as it comes up and then
      ignore them after it has gotten its configuration.

10.3.2.4 Net Booting of System Software

      A router SHOULD keep its system image in local non-volatile
      storage such as PROM, NVRAM, or disk.  It MAY also be able to load
      its system software over the network from a host or another
      router.

      A router that can keep its system image in local non-volatile
      storage MAY be configurable to boot its system image over the
      network.  A router that offers this option SHOULD be configurable
      to boot the system image in its non-volatile local storage if it
      is unable to boot its system image over the network.





Baker                       Standards Track                   [Page 128]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   DISCUSSION
      It is important that the router be able to come up and run on its
      own.  NVRAM may be a particular solution for routers used in large
      networks, since changing PROMs can be quite time consuming for a
      network manager responsible for numerous or geographically
      dispersed routers.  It is important to be able to netboot the
      system image because there should be an easy way for a router to
      get a bug fix or new feature more quickly than getting PROMs
      installed.  Also if the router has NVRAM instead of PROMs, it will
      netboot the image and then put it in NVRAM.

      Routers SHOULD perform some basic consistency check on any image
      loaded, to detect and perhaps prevent incorrect images.

   A router MAY also be able to distinguish between different
   configurations based on which software it is running.  If
   configuration commands change from one software version to another,
   it would be helpful if the router could use the configuration that
   was compatible with the software.

10.3.2.5 Detecting and responding to misconfiguration

   There MUST be mechanisms for detecting and responding to
   misconfigurations.  If a command is executed incorrectly, the router
   SHOULD give an error message.  The router SHOULD NOT accept a poorly
   formed command as if it were correct.

   DISCUSSION
      There are cases where it is not possible to detect errors: the
      command is correctly formed, but incorrect with respect to the
      network.  This may be detected by the router, but may not be
      possible.

   Another form of misconfiguration is misconfiguration of the network
   to which the router is attached.  A router MAY detect
   misconfigurations in the network.  The router MAY log these findings
   to a file, either on the router or a host, so that the network
   manager will see that there are possible problems on the network.

   DISCUSSION
      Examples of such misconfigurations might be another router with
      the same address as the one in question or a router with the wrong
      address mask.  If a router detects such problems it is probably
      not the best idea for the router to try to fix the situation.
      That could cause more harm than good.






Baker                       Standards Track                   [Page 129]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


10.3.2.6 Minimizing Disruption

   Changing the configuration of a router SHOULD have minimal affect on
   the network.  Routing tables SHOULD NOT be unnecessarily flushed when
   a simple change is made to the router.  If a router is running
   several routing protocols, stopping one routing protocol SHOULD NOT
   disrupt other routing protocols, except in the case where one network
   is learned by more than one routing protocol.

   DISCUSSION
      It is the goal of a network manager to run a network so that users
      of the network get the best connectivity possible.  Reloading a
      router for simple configuration changes can cause disruptions in
      routing and ultimately cause disruptions to the network and its
      users.  If routing tables are unnecessarily flushed, for instance,
      the default route will be lost as well as specific routes to sites
      within the network.  This sort of disruption will cause
      significant downtime for the users.  It is the purpose of this
      section to point out that whenever possible, these disruptions
      should be avoided.

10.3.2.7 Control - Troubleshooting Problems

      (1) A router MUST provide in-band network access, but (except as
           required by Section [8.2]) for security considerations this
           access SHOULD be disabled by default.  Vendors MUST document
           the default state of any in-band access.  This access SHOULD
           implement access controls, to prevent unauthorized access.

   DISCUSSION
      In-band access primarily refers to access through the normal
      network protocols that may or may not affect the permanent
      operational state of the router.  This includes, but is not
      limited to Telnet/RLOGIN console access and SNMP operations.

      This was a point of contention between the operational out of the
      box and secure out of The box contingents.  Any automagic access
      to the router may introduce insecurities, but it may be more
      important for the customer to have a router that is accessible
      over the network as soon as it is plugged in.  At least one vendor
      supplies routers without any external console access and depends
      on being able to access the router through the network to complete
      its configuration.

      It is the vendors call whether in-band access is enabled by
      default; but it is also the vendor's responsibility to make its
      customers aware of possible insecurities.




Baker                       Standards Track                   [Page 130]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


      (2) A router MUST provide the ability to initiate an ICMP echo.
           The following options SHOULD be implemented:

           o Choice of data patterns

           o Choice of packet size

           o Record route

           and the following additional options MAY be implemented:

           o Loose source route

           o Strict source route

           o Timestamps

      (3) A router SHOULD provide the ability to initiate a traceroute.
           If traceroute is provided, then the 3rd party traceroute
           SHOULD be implemented.

   Each of the above three facilities (if implemented) SHOULD have
   access restrictions placed on it to prevent its abuse by unauthorized
   persons.

10.4 Security Considerations

10.4.1 Auditing and Audit Trails

   Auditing and billing are the bane of the network operator, but are
   the two features most requested by those in charge of network
   security and those who are responsible for paying the bills.  In the
   context of security, auditing is desirable if it helps you keep your
   network working and protects your resources from abuse, without
   costing you more than those resources are worth.

   (1) Configuration Changes

        Router SHOULD provide a method for auditing a configuration
        change of a router, even if it's something as simple as
        recording the operator's initials and time of change.

   DISCUSSION
      Configuration change logging (who made a configuration change,
      what was changed, and when) is very useful, especially when
      traffic is suddenly routed through Alaska on its way across town.
      So is the ability to revert to a previous configuration.




Baker                       Standards Track                   [Page 131]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


      (2) Packet Accounting

           Vendors should strongly consider providing a system for
           tracking traffic levels between pairs of hosts or networks.
           A mechanism for limiting the collection of this information
           to specific pairs of hosts or networks is also strongly
           encouraged.

   DISCUSSION
      A host traffic matrix as described above can give the network
      operator a glimpse of traffic trends not apparent from other
      statistics.  It can also identify hosts or networks that are
      probing the structure of the attached networks - e.g., a single
      external host that tries to send packets to every IP address in
      the network address range for a connected network.

      (3) Security Auditing

           Routers MUST provide a method for auditing security related
           failures or violations to include:

           o Authorization Failures: bad passwords, invalid SNMP
              communities, invalid authorization tokens,

           o Violations of Policy Controls: Prohibited Source Routes,
              Filtered Destinations, and

           o Authorization Approvals: good passwords - Telnet in-band
              access, console access.

           Routers MUST provide a method of limiting or disabling such
           auditing but auditing SHOULD be on by default.  Possible
           methods for auditing include listing violations to a console
           if present, logging or counting them internally, or logging
           them to a remote security server through the SNMP trap
           mechanism or the Unix logging mechanism as appropriate.  A
           router MUST implement at least one of these reporting
           mechanisms - it MAY implement more than one.

10.4.2 Configuration Control

   A vendor has a responsibility to use good configuration control
   practices in the creation of the software/firmware loads for their
   routers.  In particular, if a vendor makes updates and loads
   available for retrieval over the Internet, the vendor should also
   provide a way for the customer to confirm the load is a valid one,
   perhaps by the verification of a checksum over the load.




Baker                       Standards Track                   [Page 132]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   DISCUSSION
      Many vendors currently provide short notice updates of their
      software products through the Internet.  This a good trend and
      should be encouraged, but provides a point of vulnerability in the
      configuration control process.

   If a vendor provides the ability for the customer to change the
   configuration parameters of a router remotely, for example through a
   Telnet session, the ability to do so SHOULD be configurable and
   SHOULD default to off.  The router SHOULD require  valid
   authentication before permitting remote reconfiguration.  This
   authentication procedure SHOULD NOT transmit the authentication
   secret over the network.  For example, if telnet is implemented, the
   vendor SHOULD IMPLEMENT Kerberos, S-Key, or a similar authentication
   procedure.

   DISCUSSION
      Allowing your properly identified network operator to twiddle with
      your routers is necessary; allowing anyone else to do so is
      foolhardy.

   A router MUST NOT have undocumented back door access and master
   passwords.  A vendor MUST ensure any such access added for purposes
   of debugging or product development are deleted before the product is
   distributed to its customers.

   DISCUSSION
      A vendor has a responsibility to its customers to ensure they are
      aware of the vulnerabilities present in its code by intention -
      e.g., in-band access.  Trap doors, back doors and master passwords
      intentional or unintentional can turn a relatively secure router
      into a major problem on an operational network.  The supposed
      operational benefits are not matched by the potential problems.

11. REFERENCES

   Implementors should be aware that Internet protocol standards are
   occasionally updated.  These references are current as of this
   writing, but a cautious implementor will always check a recent
   version of the RFC index to ensure that an RFC has not been updated
   or superseded by another, more recent RFC.  Reference [INTRO:6]
   explains various ways to obtain a current RFC index.

   APPL:1.
        Croft, B., and J.  Gilmore, "Bootstrap Protocol (BOOTP)", RFC
        951, Stanford University, Sun Microsystems, September 1985.





Baker                       Standards Track                   [Page 133]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   APPL:2.
        Alexander, S., and R.  Droms, "DHCP Options and BOOTP Vendor
        Extensions", RFC 1533, Lachman Technology, Inc., Bucknell
        University, October 1993.

   APPL:3.
        Wimer, W., "Clarifications and Extensions for the Bootstrap
        Protocol", RFC 1542, Carnegie Mellon University, October 1993.

   ARCH:1.
        DDN Protocol Handbook, NIC-50004, NIC-50005, NIC-50006 (three
        volumes), DDN Network Information Center, SRI International,
        Menlo Park, California, USA, December 1985.

   ARCH:2.
        V.  Cerf and R.  Kahn, "A Protocol for Packet Network
        Intercommunication", IEEE Transactions on Communication, May
        1974.  Also included in [ARCH:1].

   ARCH:3.
        J.  Postel, C.  Sunshine, and D.  Cohen, "The ARPA Internet
        Protocol", Computer Networks, volume 5, number 4, July 1981.
        Also included in [ARCH:1].

   ARCH:4.
        B.  Leiner, J.  Postel, R.  Cole, and D.  Mills, :The DARPA
        Internet Protocol Suite", Proceedings of INFOCOM '85, IEEE,
        Washington, DC, March 1985.  Also in: IEEE Communications
        Magazine, March 1985.  Also available from the Information
        Sciences Institute, University of Southern California as
        Technical Report ISI-RS-85-153.

   ARCH:5.
        D.  Comer, "Internetworking With TCP/IP Volume 1: Principles,
        Protocols, and Architecture", Prentice Hall, Englewood Cliffs,
        NJ, 1991.

   ARCH:6.
        W.  Stallings, "Handbook of Computer-Communications Standards
        Volume 3: The TCP/IP Protocol Suite", Macmillan, New York, NY,
        1990.

   ARCH:7.
        Postel, J., "Internet Official Protocol Standards", STD 1, RFC
        1780, Internet Architecture Board, March 1995.






Baker                       Standards Track                   [Page 134]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   ARCH:8.
        Information processing systems - Open Systems Interconnection -
        Basic Reference Model, ISO 7489, International Standards
        Organization, 1984.

   ARCH:9
        R.  Braden, J.  Postel, Y.  Rekhter, "Internet Architecture
        Extensions for Shared Media", 05/20/1994

   FORWARD:1.
        IETF CIP Working Group (C. Topolcic, Editor), "Experimental
        Internet Stream Protocol", Version 2 (ST-II), RFC 1190, October
        1990.

   FORWARD:2.
        Mankin, A., and K.  Ramakrishnan, Editors, "Gateway Congestion
        Control Survey", RFC 1254, MITRE, Digital Equipment Corporation,
        August 1991.

   FORWARD:3.
        J.  Nagle, "On Packet Switches with Infinite Storage", IEEE
        Transactions on Communications, volume COM-35, number 4, April
        1987.

   FORWARD:4.
        R.  Jain, K.  Ramakrishnan, and D.  Chiu, "Congestion Avoidance
        in Computer Networks With a Connectionless Network Layer",
        Technical Report DEC-TR-506, Digital Equipment Corporation.

   FORWARD:5.
        V.  Jacobson, "Congestion Avoidance and Control", Proceedings of
        SIGCOMM '88, Association for Computing Machinery, August 1988.

   FORWARD:6.
        W.  Barns, "Precedence and Priority Access Implementation for
        Department of Defense Data Networks", Technical Report MTR-
        91W00029, The Mitre Corporation, McLean, Virginia, USA, July
        1991.

   FORWARD:7
        Fang, Chen, Hutchins, "Simulation Results of TCP Performance
        over ATM with and without Flow Control", presentation to the ATM
        Forum, November 15, 1993.

   FORWARD:8
        V.  Paxson, S.  Floyd "Wide Area Traffic: the Failure of Poisson
        Modeling", short version in SIGCOMM '94.




Baker                       Standards Track                   [Page 135]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   FORWARD:9
        Leland, Taqqu, Willinger and Wilson, "On the Self-Similar Nature
        of Ethernet Traffic", Proceedings of SIGCOMM '93, September,
        1993.

   FORWARD:10
        S.  Keshav "A Control Theoretic Approach to Flow Control",
        SIGCOMM 91, pages 3-16

   FORWARD:11
        K.K.  Ramakrishnan and R.  Jain, "A Binary Feedback Scheme for
        Congestion Avoidance in Computer Networks", ACM Transactions of
        Computer Systems, volume 8, number 2, 1980.

   FORWARD:12
        H.  Kanakia, P.  Mishara, and A.  Reibman].  "An adaptive
        congestion control scheme for real-time packet video transport",
        In Proceedings of ACM SIGCOMM 1994, pages 20-31, San Francisco,
        California, September 1993.

   FORWARD:13
        A.  Demers, S.  Keshav, S.  Shenker, "Analysis and Simulation of
        a Fair Queuing Algorithm",
         93 pages 1-12

   FORWARD:14
        Clark, D., Shenker, S., and L.  Zhang, "Supporting Real-Time
        Applications in an Integrated Services Packet Network:
        Architecture and Mechanism", 92 pages 14-26

   INTERNET:1.
        Postel, J., "Internet Protocol", STD 5, RFC 791, USC/Information
        Sciences Institute, September 1981.

   INTERNET:2.
        Mogul, J., and J.  Postel, "Internet Standard Subnetting
        Procedure", STD 5, RFC 950, Stanford, USC/Information Sciences
        Institute, August 1985.

   INTERNET:3.
        Mogul, J., "Broadcasting Internet Datagrams in the Presence of
        Subnets", STD 5, RFC 922, Stanford University, October 1984.

   INTERNET:4.
        Deering, S., "Host Extensions for IP Multicasting", STD 5, RFC
        1112, Stanford University, August 1989.





Baker                       Standards Track                   [Page 136]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   INTERNET:5.
        Kent, S., "U.S.  Department of Defense Security Options for the
        Internet Protocol", RFC 1108, BBN Communications, November 1991.

   INTERNET:6.
        Braden, R., Borman, D., and C.  Partridge, "Computing the
        Internet Checksum", RFC 1071, USC/Information Sciences
        Institute, Cray Research, BBN Communications, September 1988.

   INTERNET:7.
        Mallory T., and A.  Kullberg, "Incremental Updating of the
        Internet Checksum", RFC 1141, BBN Communications, January 1990.

   INTERNET:8.
        Postel, J., "Internet Control Message Protocol", STD 5, RFC 792,
        USC/Information Sciences Institute, September 1981.

   INTERNET:9.
        A.  Mankin, G.  Hollingsworth, G.  Reichlen, K.  Thompson, R.
        Wilder, and R.  Zahavi, "Evaluation of Internet Performance -
        FY89", Technical Report MTR-89W00216, MITRE Corporation,
        February, 1990.

   INTERNET:10.
        G.  Finn, A "Connectionless Congestion Control Algorithm",
        Computer Communications Review, volume 19, number 5, Association
        for Computing Machinery, October 1989.

   INTERNET:11.
        Prue, W., and J. Postel, "The Source Quench Introduced Delay
        (SQuID)", RFC 1016, USC/Information Sciences Institute, August
        1987.

   INTERNET:12.
        McKenzie, A., "Some comments on SQuID", RFC 1018, BBN Labs,
        August 1987.

   INTERNET:13.
        Deering, S., "ICMP Router Discovery Messages", RFC 1256, Xerox
        PARC, September 1991.

   INTERNET:14.
        Mogul J., and S.  Deering, "Path MTU Discovery", RFC 1191,
        DECWRL, Stanford University, November 1990.







Baker                       Standards Track                   [Page 137]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   INTERNET:15
        Fuller, V., Li, T., Yu, J., and K.  Varadhan, "Classless Inter-
        Domain Routing (CIDR): an Address Assignment and Aggregation
        Strategy" RFC 1519, BARRNet, cisco, Merit, OARnet, September
        1993.

   INTERNET:16
        St.  Johns, M., "Draft Revised IP Security Option", RFC 1038,
        IETF, January 1988.

   INTERNET:17
        Prue, W.,  and J.  Postel, "Queuing Algorithm to Provide Type-
        of-service For IP Links", RFC 1046, USC/Information Sciences
        Institute, February 1988.

   INTERNET:18
        Postel, J., "Address Mappings", RFC 796, USC/Information
        Sciences Institute, September 1981.

   INTRO:1.
        Braden, R., and J.  Postel, "Requirements for Internet
        Gateways", STD 4, RFC 1009, USC/Information Sciences Institute,
        June 1987.

   INTRO:2.
        Internet Engineering Task Force (R. Braden, Editor),
        "Requirements for Internet Hosts - Communication Layers", STD 3,
        RFC 1122, USC/Information Sciences Institute, October 1989.

   INTRO:3.
        Internet Engineering Task Force (R. Braden, Editor),
        "Requirements for Internet Hosts - Application and Support", STD
        3, RFC 1123, USC/Information Sciences Institute, October 1989.

   INTRO:4.
        Clark, D., "Modularity and Efficiency in Protocol
        Implementations", RFC 817, MIT Laboratory for Computer Science,
        July 1982.

   INTRO:5.
        Clark, D., "The Structuring of Systems Using Upcalls",
        Proceedings of 10th ACM SOSP, December 1985.

   INTRO:6.
        Jacobsen, O.,  and J.  Postel, "Protocol Document Order
        Information", RFC 980, SRI, USC/Information Sciences Institute,
        March 1986.




Baker                       Standards Track                   [Page 138]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   INTRO:7.
        Reynolds, J.,  and J.  Postel, "Assigned Numbers", STD 2, RFC
        1700, USC/Information Sciences Institute, October 1994.  This
        document is periodically updated and reissued with a new number.
        It is wise to verify occasionally that the version you have is
        still current.

   INTRO:8.
        DoD Trusted Computer System Evaluation Criteria, DoD publication
        5200.28-STD, U.S.  Department of Defense, December 1985.

   INTRO:9
        Malkin, G., and T.  LaQuey Parker, Editors, "Internet Users'
        Glossary", FYI 18, RFC 1392, Xylogics, Inc., UTexas, January
        1993.

   LINK:1.
        Leffler, S., and M.  Karels, "Trailer Encapsulations", RFC 893,
        University of California at Berkeley, April 1984.

   LINK:2
        Simpson, W., "The Point-to-Point Protocol (PPP)", STD 51, RFC
        1661, Daydreamer July 1994.

   LINK:3
        McGregor, G., "The PPP Internet Protocol Control Protocol
        (IPCP)", RFC 1332, Merit May 1992.

   LINK:4
        Lloyd, B., and W.  Simpson, "PPP Authentication Protocols", RFC
        1334, L&A, Daydreamer, May 1992.

   LINK:5
        Simpson, W., "PPP Link Quality Monitoring", RFC 1333,
        Daydreamer, May 1992.

   MGT:1.
        Rose, M., and K.  McCloghrie, "Structure and Identification of
        Management Information of TCP/IP-based Internets", STD 16, RFC
        1155, Performance Systems International, Hughes LAN Systems, May
        1990.

   MGT:2.
        McCloghrie, K., and M.  Rose (Editors), "Management Information
        Base of TCP/IP-Based Internets: MIB-II", STD 16, RFC 1213,
        Hughes LAN Systems, Inc., Performance Systems International,
        March 1991.




Baker                       Standards Track                   [Page 139]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   MGT:3.
        Case, J., Fedor, M., Schoffstall, M., and J.  Davin, "Simple
        Network Management Protocol", STD 15, RFC 1157, SNMP Research,
        Performance Systems International, MIT Laboratory for Computer
        Science, May 1990.

   MGT:4.
        Rose, M., and K.  McCloghrie (Editors), "Towards Concise MIB
        Definitions", STD 16, RFC 1212, Performance Systems
        International, Hughes LAN Systems, March 1991.

   MGT:5.
        Steinberg, L., "Techniques for Managing Asynchronously Generated
        Alerts", RFC 1224, IBM Corporation, May 1991.

   MGT:6.
        Kastenholz, F., "Definitions of Managed Objects for the
        Ethernet-like Interface Types", RFC 1398, FTP Software, Inc.,
        January 1993.

   MGT:7.
        McCloghrie, K., and R. Fox "IEEE 802.4 Token Bus MIB", RFC 1230,
        Hughes LAN Systems, Inc., Synoptics, Inc., May 1991.

   MGT:8.
        McCloghrie, K., Fox R., and E. Decker, "IEEE 802.5 Token Ring
        MIB", RFC 1231, Hughes LAN Systems, Inc., Synoptics, Inc., cisco
        Systems, Inc., February 1993.

   MGT:9.
        Case, J., and A.  Rijsinghani, "FDDI Management Information
        Base", RFC 1512, The University of Tennesse and SNMP Research,
        Digital Equipment Corporation, September 1993.

   MGT:10.
        Stewart, B., Editor "Definitions of Managed Objects for RS-232-
        like Hardware Devices", RFC 1317, Xyplex, Inc., April 1992.

   MGT:11.
        Kastenholz, F., "Definitions of Managed Objects for the Link
        Control Protocol of the Point-to-Point Protocol", RFC 1471, FTP
        Software, Inc., June 1992.

   MGT:12.
        Kastenholz, F., "The Definitions of Managed Objects for the
        Security Protocols of the Point-to-Point Protocol", RFC 1472,
        FTP Software, Inc., June 1992.




Baker                       Standards Track                   [Page 140]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   MGT:13.
        Kastenholz, F., "The Definitions of Managed Objects for the IP
        Network Control Protocol of the Point-to-Point Protocol", RFC
        1473, FTP Software, Inc., June 1992.

   MGT:14.
        Baker, F., and R.  Coltun, "OSPF Version 2 Management
        Information Base", RFC 1253, ACC, Computer Science Center,
        August 1991.

   MGT:15.
        Willis, S., and J.  Burruss, "Definitions of Managed Objects for
        the Border Gateway Protocol (Version 3)", RFC 1269, Wellfleet
        Communications Inc., October 1991.

   MGT:16.
        Baker, F., and J.  Watt, "Definitions of Managed Objects for the
        DS1 and E1 Interface Types", RFC 1406, Advanced Computer
        Communications, Newbridge Networks Corporation, January 1993.

   MGT:17.
        Cox, T., and K.  Tesink, Editors "Definitions of Managed Objects
        for the DS3/E3 Interface Types", RFC 1407, Bell Communications
        Research, January 1993.

   MGT:18.
        McCloghrie, K., "Extensions to the Generic-Interface MIB", RFC
        1229, Hughes LAN Systems, August 1992.

   MGT:19.
        Cox, T., and K.  Tesink, "Definitions of Managed Objects for the
        SIP Interface Type", RFC 1304, Bell Communications Research,
        February 1992.

   MGT:20
        Baker, F., "IP Forwarding Table MIB", RFC 1354, ACC, July 1992.

   MGT:21.
        Malkin, G., and F.  Baker, "RIP Version 2 MIB Extension", RFC
        1724, Xylogics, Inc., Cisco Systems, November 1994

   MGT:22.
        Throop, D., "SNMP MIB Extension for the X.25 Packet Layer", RFC
        1382, Data General Corporation, November 1992.







Baker                       Standards Track                   [Page 141]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   MGT:23.
        Throop, D., and F.  Baker, "SNMP MIB Extension for X.25 LAPB",
        RFC 1381, Data General Corporation, ACC, November 1992.

   MGT:24.
        Throop, D., and F.  Baker, "SNMP MIB Extension for MultiProtocol
        Interconnect over X.25", RFC 1461, Data General Corporation, May
        1993.

   MGT:25.
        Rose, M., "SNMP over OSI", RFC 1418, Dover Beach Consulting,
        Inc., March 1993.

   MGT:26.
        Minshall, G., and M.  Ritter, "SNMP over AppleTalk", RFC 1419,
        Novell, Inc., Apple Computer, Inc., March 1993.

   MGT:27.
        Bostock, S., "SNMP over IPX", RFC 1420, Novell, Inc., March
        1993.

   MGT:28.
        Schoffstall, M., Davin, C., Fedor, M., and J.  Case, "SNMP over
        Ethernet", RFC 1089, Rensselaer Polytechnic Institute, MIT
        Laboratory for Computer Science, NYSERNet, Inc., University of
        Tennessee at Knoxville, February 1989.

   MGT:29.
        Case, J., "FDDI Management Information Base", RFC 1285, SNMP
        Research, Incorporated, January 1992.

   OPER:1.
        Nagle, J., "Congestion Control in IP/TCP Internetworks", RFC
        896, FACC, January 1984.

   OPER:2.
        Sollins, K., "TFTP Protocol (revision 2)", RFC 1350, MIT, July
        1992.

   ROUTE:1.
        Moy, J., "OSPF Version 2", RFC 1583, Proteon, March 1994.

   ROUTE:2.
        Callon, R., "Use of OSI IS-IS for Routing in TCP/IP and Dual
        Environments", RFC 1195, DEC, December 1990.






Baker                       Standards Track                   [Page 142]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   ROUTE:3.
        Hedrick, C., "Routing Information Protocol", RFC 1058, Rutgers
        University, June 1988.

   ROUTE:4.
        Lougheed, K., and Y.  Rekhter, "A Border Gateway Protocol 3
        (BGP-3)", RFC 1267, cisco, T.J. Watson Research Center, IBM
        Corp., October 1991.

   ROUTE:5.
        Gross, P, and Y.  Rekhter, "Application of the Border Gateway
        Protocol in the Internet", RFC 1772, T.J. Watson Research
        Center, IBM Corp., MCI, March 1995.

   ROUTE:6.
        Mills, D., "Exterior Gateway Protocol Formal Specification", RFC
        904, UDEL, April 1984.

   ROUTE:7.
        Rosen, E., "Exterior Gateway Protocol (EGP)", RFC 827, BBN,
        October 1982.

   ROUTE:8.
        Seamonson, L, and E.  Rosen, "STUB" "Exterior Gateway Protocol",
        RFC 888, BBN, January 1984.

   ROUTE:9.
        Waitzman, D., Partridge, C., and S.  Deering, "Distance Vector
        Multicast Routing Protocol", RFC 1075, BBN, Stanford, November
        1988.

   ROUTE:10.
        Deering, S., Multicast Routing in Internetworks and Extended
        LANs, Proceedings of '88, Association for Computing Machinery,
        August 1988.

   ROUTE:11.
        Almquist, P., "Type of Service in the Internet Protocol Suite",
        RFC 1349, Consultant, July 1992.

   ROUTE:12.
        Rekhter, Y., "Experience with the BGP Protocol", RFC 1266, T.J.
        Watson Research Center, IBM Corp., October 1991.

   ROUTE:13.
        Rekhter, Y., "BGP Protocol Analysis", RFC 1265, T.J. Watson
        Research Center, IBM Corp., October 1991.




Baker                       Standards Track                   [Page 143]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   TRANS:1.
        Postel, J., "User Datagram Protocol", STD 6, RFC 768,
        USC/Information Sciences Institute, August 1980.

   TRANS:2.
        Postel, J., "Transmission Control Protocol", STD 7, RFC 793,
        USC/Information Sciences Institute, September 1981.












































Baker                       Standards Track                   [Page 144]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


APPENDIX A. REQUIREMENTS FOR SOURCE-ROUTING HOSTS

   Subject to restrictions given below, a host MAY be able to act as an
   intermediate hop in a source route, forwarding a source-routed
   datagram to the next specified hop.

   However, in performing this router-like function, the host MUST obey
   all the relevant rules for a router forwarding source-routed
   datagrams [INTRO:2].  This includes the following specific
   provisions:

   (A) TTL
        The TTL field MUST be decremented and the datagram perhaps
        discarded as specified for a router in [INTRO:2].

   (B) ICMP Destination Unreachable
        A host MUST be able to generate Destination Unreachable messages
        with the following codes:
        4 (Fragmentation Required but DF Set) when a source-routed
          datagram cannot be fragmented to fit into the target network;
        5 (Source Route Failed) when a source-routed datagram cannot be
          forwarded, e.g., because of a routing problem or because the
          next hop of a strict source route is not on a connected
          network.

   (C) IP Source Address
        A source-routed datagram being forwarded MAY (and normally will)
        have a source address that is not one of the IP addresses of the
        forwarding host.

   (D) Record Route Option
        A host that is forwarding a source-routed datagram containing a
        Record Route option MUST update that option, if it has room.

   (E) Timestamp Option
        A host that is forwarding a source-routed datagram containing a
        Timestamp Option MUST add the current timestamp to that option,
        according to the rules for this option.

   To define the rules restricting host forwarding of source-routed
   datagrams, we use the term local source-routing if the next hop will
   be through the same physical interface through which the datagram
   arrived; otherwise, it is non-local source-routing.

   A host is permitted to perform local source-routing without
   restriction.





Baker                       Standards Track                   [Page 145]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   A host that supports non-local source-routing MUST have a
   configurable switch to disable forwarding, and this switch MUST
   default to disabled.

   The host MUST satisfy all router requirements for configurable policy
   filters [INTRO:2] restricting non-local forwarding.

   If a host receives a datagram with an incomplete source route but
   does not forward it for some reason, the host SHOULD return an ICMP
   Destination Unreachable (code 5, Source Route Failed) message, unless
   the datagram was itself an ICMP error message.

APPENDIX B. GLOSSARY

   This Appendix defines specific terms used in this memo.  It also
   defines some general purpose terms that may be of interest.  See also
   [INTRO:9] for a more general set of definitions.

   Autonomous System (AS)
        An Autonomous System (AS) is a connected segment of a network
        topology that consists of a collection of subnetworks (with
        hosts attached) interconnected by a set of routes.  The
        subnetworks and the routers are expected to be under the control
        of a single operations and maintenance (O&M) organization.
        Within an AS routers may use one or more interior routing
        protocols, and sometimes several sets of metrics.  An AS is
        expected to present to other ASs an appearence of a coherent
        interior routing plan, and a consistent picture of the
        destinations reachable through the AS.  An AS is identified by
        an Autonomous System number.
   Connected Network
        A network prefix to which a router is interfaced is often known
        as a local network or the subnetwork of that router.  However,
        these terms can cause confusion, and therefore we use the term
        Connected Network in this memo.

   Connected (Sub)Network
        A Connected (Sub)Network is an IP subnetwork to which a router
        is interfaced, or a connected network if the connected network
        is not subnetted.  See also Connected Network.

   Datagram
        The unit transmitted between a pair of internet modules.  Data,
        called datagrams, from sources to destinations.  The Internet
        Protocol does not provide a reliable communication facility.
        There are no acknowledgments either end-to-end or hop-by-hop.
        There is no error no retransmissions.  There is no flow control.
        See IP.



Baker                       Standards Track                   [Page 146]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   Default Route
        A routing table entry that is used to direct any data addressed
        to any network prefixes not explicitly listed in the routing
        table.

   Dense Mode
        In multicast forwarding, two paradigms are possible: in Dense
        Mode forwarding, a network multicast is forwarded as a data link
        layer multicast to all interfaces except that on which it was
        received, unless and until the router is instructed not to by a
        multicast routing neighbor.  See Sparse Mode.

   EGP
        Exterior Gateway Protocol A protocol that distributes routing
        information to the gateways (routers) which connect autonomous
        systems.  See IGP.

   EGP-2
        Exterior Gateway Protocol version 2 This is an EGP routing
        protocol developed to handle traffic between Autonomous Systems
        in the Internet.

   Forwarder
        The logical entity within a router that is responsible for
        switching packets among the router's interfaces.  The Forwarder
        also makes the decisions to queue a packet for local delivery,
        to queue a packet for transmission out another interface, or
        both.

   Forwarding
        Forwarding is the process a router goes through for each packet
        received by the router.  The packet may be consumed by the
        router, it may be output on one or more interfaces of the
        router, or both.  Forwarding includes the process of deciding
        what to do with the packet as well as queuing it up for
        (possible) output or internal consumption.

   Forwarding Information Base (FIB)
        The table containing the information necessary to forward IP
        Datagrams, in this document, is called the Forwarding
        Information Base.  At minimum, this contains the interface
        identifier and next hop information for each reachable
        destination network prefix.

   Fragment
        An IP datagram that represents a portion of a higher layer's
        packet that was too large to be sent in its entirety over the
        output network.



Baker                       Standards Track                   [Page 147]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   General Purpose Serial Interface
        A physical medium capable of connecting exactly two systems, and
        therefore configurable as a point to point line, but also
        configurable to support link layer networking using protocols
        such as X.25 or Frame Relay.  A link layer network connects
        another system to a switch, and a higher communication layer
        multiplexes virtual circuits on the connection.  See Point to
        Point Line.

   IGP
        Interior Gateway Protocol A protocol that distributes routing
        information with an Autonomous System (AS).  See EGP.

   Interface IP Address
        The IP Address and network prefix length that is assigned to a
        specific interface of a router.

   Internet Address
        An assigned number that identifies a host in an internet.  It
        has two parts: an IP address and a prefix length.  The prefix
        length indicates how many of the most specific bits of the
        address constitute the network prefix.

   IP
        Internet Protocol The network layer protocol for the Internet.
        It is a packet switching, datagram protocol defined in RFC 791.
        IP does not provide a reliable communications facility; that is,
        there are no end-to-end of hop-by-hop acknowledgments.

   IP Datagram
        An IP Datagram is the unit of end-to-end transmission in the
        Internet Protocol.  An IP Datagram consists of an IP header
        followed by all of higher-layer data (such as TCP, UDP, ICMP,
        and the like).  An IP Datagram is an IP header followed by a
        message.

        An IP Datagram is a complete IP end-to-end transmission unit.
        An IP Datagram is composed of one or more IP Fragments.

        In this memo, the unqualified term Datagram should be understood
        to refer to an IP Datagram.

   IP Fragment
        An IP Fragment is a component of an IP Datagram.  An IP Fragment
        consists of an IP header followed by all or part of the higher-
        layer of the original IP Datagram.

        One or more IP Fragments comprises a single IP Datagram.



Baker                       Standards Track                   [Page 148]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


        In this memo, the unqualified term Fragment should be understood
        to refer to an IP Fragment.

   IP Packet
        An IP Datagram or an IP Fragment.

        In this memo, the unqualified term Packet should generally be
        understood to refer to an IP Packet.

   Logical [network] interface
        We define a logical [network] interface to be a logical path,
        distinguished by a unique IP address, to a connected network.

   Martian Filtering
        A packet that contains an invalid source or destination address
        is considered to be martian and discarded.

   MTU (Maximum Transmission Unit)
        The size of the largest packet that can be transmitted or
        received through a logical interface.  This size includes the IP
        header but does not include the size of any Link Layer headers
        or framing.

   Multicast
        A packet that is destined for multiple hosts.  See broadcast.

   Multicast Address
        A special type of address that is recognizable by multiple
        hosts.

        A Multicast Address is sometimes known as a Functional Address
        or a Group Address.

   Network Prefix
        The portion of an IP Address that signifies a set of systems.
        It is selected from the IP Address by logically ANDing a subnet
        mask with the address, or (equivalently) setting the bits of the
        address not among the most significant  bits of
        the address to zero.

   Originate
        Packets can be transmitted by a router for one of two reasons:
        1) the packet was received and is being forwarded or 2) the
        router itself created the packet for transmission (such as route
        advertisements).  Packets that the router creates for
        transmission are said to originate at the router.





Baker                       Standards Track                   [Page 149]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   Packet
        A packet is the unit of data passed across the interface between
        the Internet Layer and the Link Layer.  It includes an IP header
        and data.  A packet may be a complete IP datagram or a fragment
        of an IP datagram.

   Path
        The sequence of routers and (sub-)networks that a packet
        traverses from a particular router to a particular destination
        host.  Note that a path is uni-directional; it is not unusual to
        have different paths in the two directions between a given host
        pair.

   Physical Network
        A Physical Network is a network (or a piece of an internet)
        which is contiguous at the Link Layer.  Its internal structure
        (if any) is transparent to the Internet Layer.

        In this memo, several media components that are connected using
        devices such as bridges or repeaters are considered to be a
        single Physical Network since such devices are transparent to
        the IP.

   Physical Network Interface
        This is a physical interface to a Connected Network and has a
        (possibly unique) Link-Layer address.  Multiple Physical Network
        Interfaces on a single router may share the same Link-Layer
        address, but the address must be unique for different routers on
        the same Physical Network.

   Point to Point Line
        A physical medium capable of connecting exactly two systems.  In
        this document, it is only used to refer to such a line when used
        to connect IP entities.  See General Purpose Serial Interface.

   router
        A special-purpose dedicated computer that connects several
        networks.  Routers switch packets between these networks in a
        process known as forwarding.  This process may be repeated
        several times on a single packet by multiple routers until the
        packet can be delivered to the final destination - switching the
        packet from router to router to router...  until the packet gets
        to its destination.

   RPF
        Reverse Path Forwarding - A method used to deduce the next hops
        for broadcast and multicast packets.




Baker                       Standards Track                   [Page 150]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   Silently Discard
        This memo specifies several cases where a router is to Silently
        Discard a received packet (or datagram).  This means that the
        router should discard the packet without further processing, and
        that the router will not send any ICMP error message (see
        Section [4.3.2]) as a result.  However, for diagnosis of
        problems, the router should provide the capability of logging
        the error (see Section [1.3.3]), including the contents of the
        silently discarded packet, and should record the event in a
        statistics counter.

   Silently Ignore
        A router is said to Silently Ignore an error or condition if it
        takes no action other than possibly generating an error report
        in an error log or through some network management protocol, and
        discarding, or ignoring, the source of the error.  In
        particular, the router does NOT generate an ICMP error message.

   Sparse Mode
        In multicast forwarding, two paradigms are possible: in Sparse
        Mode forwarding, a network layer multicast datagram is forwarded
        as a data link layer multicast frame to routers and hosts that
        have asked for it.  The initial forwarding state is the inverse
        of dense-mode in that it assumes no part  of the network wants
        the data.  See Dense Mode.

   Specific-destination address
        This is defined to be the destination address in the IP header
        unless the header contains an IP broadcast or IP multicast
        address, in which case the specific-destination is an IP address
        assigned to the physical interface on which the packet arrived.

   subnet
        A portion of a network, which may be a physically independent
        network, which shares a network address with other portions of
        the network and is distinguished by a subnet number.  A subnet
        is to a network what a network is to an internet.

   subnet number
        A part of the internet address that designates a subnet.  It is
        ignored for the purposes internet routing, but is used for
        intranet routing.

   TOS
        Type Of Service A field in the IP header that represents the
        degree of reliability expected from the network layer by the
        transport layer or application.




Baker                       Standards Track                   [Page 151]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   TTL
        Time To Live A field in the IP header that represents how long a
        packet is considered valid.  It is a combination hop count and
        timer value.

APPENDIX C. FUTURE DIRECTIONS

   This appendix lists work that future revisions of this document may
   wish to address.

   In the preparation of Router Requirements, we stumbled across several
   other architectural issues.  Each of these is dealt with somewhat in
   the document, but still ought to be classified as an open issue in
   the IP architecture.

   Most of the he topics presented here generally indicate areas where
   the technology is still relatively new and it is not appropriate to
   develop specific requirements since the community is still gaining
   operational experience.

   Other topics represent areas of ongoing research and indicate areas
   that the prudent developer would closely monitor.

   (1) SNMP Version 2

   (2) Additional SNMP MIBs

   (7) More detailed requirements for leaking routes between routing
        protocols

   (8) Router system security

   (9) Routing protocol security

   (10) Internetwork Protocol layer security.  There has been extensive
        work refining the security of IP since the original work writing
        this document.  This security work should be included in here.

   (12) Load Splitting

   (13) Sending fragments along different paths


   (15) Multiple logical (sub)nets on the same wire.  Router
        Requirements does not require support for this.  We made some
        attempt to identify pieces of the architecture (e.g., forwarding
        of directed broadcasts and issuing of Redirects) where the
        wording of the rules has to be done carefully to make the right



Baker                       Standards Track                   [Page 152]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


        thing happen, and tried to clearly distinguish logical
        interfaces from physical interfaces.  However, we did not study
        this issue in detail, and we are not at all confident that all
        the rules in the document are correct in the presence of
        multiple logical (sub)nets on the same wire.

   (15) Congestion control and resource management.  On the advice of
        the IETF's experts (Mankin and Ramakrishnan) we deprecated
        (SHOULD NOT) Source Quench and said little else concrete
        (Section 5.3.6).

   (16) Developing a Link-Layer requirements document that would be
        common for both routers and hosts.

   (17) Developing a common PPP LQM algorithm.

   (18) Investigate of other information (above and beyond section
        [3.2]) that passes between the layers, such as physical network
        MTU, mappings of IP precedence to Link Layer priority values,
        etc.

   (19) Should the Link Layer notify IP if address resolution failed
        (just like it notifies IP when there is a Link Layer priority
        value problem)?

   (20) Should all routers be required to implement a DNS resolver?

   (21) Should a human user be able to use a host name anywhere you can
        use an IP address when configuring the router?  Even in ping and
        traceroute?

   (22) Almquist's draft ruminations on the next hop and ruminations on
        route leaking need to be reviewed, brought up to date, and
        published.

   (23) Investigation is needed to determine if a redirect message for
        precedence is needed or not.  If not, are the type-of-service
        redirects acceptable?

   (24) RIPv2 and RIP+CIDR and variable length network prefixes.

   (25) BGP-4 CIDR is going to be important, and everyone is betting on
        BGP-4.  We can't avoid mentioning it.  Probably need to describe
        the differences between BGP-3 and BGP-4, and explore upgrade
        issues...

   (26) Loose Source Route Mobile IP and some multicasting may require
        this.  Perhaps it should be elevated to a SHOULD (per Fred



Baker                       Standards Track                   [Page 153]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


        Baker's Suggestion).


APPENDIX D. Multicast Routing Protocols

   Multicasting is a relatively new technology within the Internet
   Protocol family.  It is not widely deployed or commonly in use yet.
   Its importance, however, is expected to grow over the coming years.

   This Appendix describes some of the technologies being investigated
   for routing multicasts through the Internet.

   A diligent implementor will keep abreast of developments in this area
   to properly develop multicast facilities.

   This Appendix does not specify any standards or requirements.

D.1 Introduction

   Multicast routing protocols enable the forwarding of IP multicast
   datagrams throughout a TCP/IP internet.  Generally these algorithms
   forward the datagram based on its source and destination addresses.
   Additionally, the datagram may need to be forwarded to several
   multicast group members, at times requiring the datagram to be
   replicated and sent out multiple interfaces.

   The state of multicast routing protocols is less developed than the
   protocols available for the forwarding of IP unicasts.  Three
   experimental multicast routing protocols have been documented for
   TCP/IP.  Each uses the IGMP protocol (discussed in Section [4.4]) to
   monitor multicast group membership.

D.2 Distance Vector Multicast Routing Protocol - DVMRP

   DVMRP, documented in [ROUTE:9], is based on Distance Vector or
   Bellman-Ford technology.  It routes multicast datagrams only, and
   does so within a single Autonomous System.  DVMRP is an
   implementation of the Truncated Reverse Path Broadcasting algorithm
   described in [ROUTE:10].  In addition, it specifies the tunneling of
   IP multicasts through non-multicast-routing-capable IP domains.

D.3 Multicast Extensions to OSPF - MOSPF

   MOSPF, currently under development, is a backward-compatible addition
   to OSPF that allows the forwarding of both IP multicasts and unicasts
   within an Autonomous System.  MOSPF routers can be mixed with OSPF
   routers within a routing domain, and they will interoperate in the
   forwarding of unicasts.  OSPF is a link-state or SPF-based protocol.



Baker                       Standards Track                   [Page 154]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   By adding link state advertisements that pinpoint group membership,
   MOSPF routers can calculate the path of a multicast datagram as a
   tree rooted at the datagram source.  Those branches that do not
   contain group members can then be discarded, eliminating unnecessary
   datagram forwarding hops.

D.4 Protocol Independent Multicast - PIM

   PIM, currently under development, is a multicast routing protocol
   that runs over an existing unicast infrastructure.  PIM provides for
   both dense and sparse group membership.  It is different from other
   protocols, since it uses an explicit join model for sparse groups.
   Joining occurs on a shared tree and can switch to a per-source tree.
   Where bandwidth is plentiful and group membership is dense, overhead
   can be reduced by flooding data out all links and later pruning
   exception cases where there are no group members.

APPENDIX E Additional Next-Hop Selection Algorithms

   Section [5.2.4.3] specifies an algorithm that routers ought to use
   when selecting a next-hop for a packet.

   This appendix provides historical perspective for the next-hop
   selection problem.  It also presents several additional pruning rules
   and next-hop selection algorithms that might be found in the
   Internet.

   This appendix presents material drawn from an earlier, unpublished,
   work by Philip Almquist; Ruminations on the Next Hop.

   This Appendix does not specify any standards or requirements.

E.1. Some Historical Perspective

   It is useful to briefly review the history of the topic, beginning
   with what is sometimes called the "classic model" of how a router
   makes routing decisions.  This model predates IP.  In this model, a
   router speaks some single routing protocol such as RIP.  The protocol
   completely determines the contents of the router's Forwarding
   Information Base (FIB).  The route lookup algorithm is trivial: the
   router looks in the FIB for a route whose destination attribute
   exactly matches the network prefix portion of the destination address
   in the packet.  If one is found, it is used; if none is found, the
   destination is unreachable.  Because the routing protocol keeps at
   most one route to each destination, the problem of what to do when
   there are multiple routes that match the same destination cannot
   arise.




Baker                       Standards Track                   [Page 155]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   Over the years, this classic model has been augmented in small ways.
   With the deployment of default routes, subnets, and host routes, it
   became possible to have more than one routing table entry which in
   some sense matched the destination.  This was easily resolved by a
   consensus that there was a hierarchy of routes: host routes should be
   preferred over subnet routes, subnet routes over net routes, and net
   routes over default routes.

   With the deployment of technologies supporting variable length subnet
   masks (variable length network prefixes), the general approach
   remained the same although its description became a little more
   complicated; network prefixes were introduced as a conscious
   simplification and regularization of the architecture.  We now say
   that each route to a network prefix route has a prefix length
   associated with it.  This prefix length indicates the number of bits
   in the prefix.  This may also be represented using the classical
   subnet mask.  A route cannot be used to route a packet unless each
   significant bit in the route's network prefix matches the
   corresponding bit in the packet's destination address.  Routes with
   more bits set in their masks are preferred over routes that have
   fewer bits set in their masks.  This is simply a generalization of
   the hierarchy of routes described above, and will be referred to for
   the rest of this memo as choosing a route by preferring longest
   match.

   Another way the classic model has been augmented is through a small
   amount of relaxation of the notion that a routing protocol has
   complete control over the contents of the routing table.  First,
   static routes were introduced.  For the first time, it was possible
   to simultaneously have two routes (one dynamic and one static) to the
   same destination.  When this happened, a router had to have a policy
   (in some cases configurable, and in other cases chosen by the author
   of the router's software) which determined whether the static route
   or the dynamic route was preferred.  However, this policy was only
   used as a tie-breaker when longest match didn't uniquely determine
   which route to use.  Thus, for example, a static default route would
   never be preferred over a dynamic net route even if the policy
   preferred static routes over dynamic routes.

   The classic model had to be further augmented when inter-domain
   routing protocols were invented.  Traditional routing protocols came
   to be called "interior gateway protocols" (IGPs), and at each
   Internet site there was a strange new beast called an "exterior
   gateway", a router that spoke EGP to several "BBN Core Gateways" (the
   routers that made up the Internet backbone at the time) at the same
   time as it spoke its IGP to the other routers at its site.  Both
   protocols wanted to determine the contents of the router's routing
   table.  Theoretically, this could result in a router having three



Baker                       Standards Track                   [Page 156]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   routes (EGP, IGP, and static) to the same destination.  Because of
   the Internet topology at the time, it was resolved with little debate
   that routers would be best served by a policy of preferring IGP
   routes over EGP routes.  However, the sanctity of longest match
   remained unquestioned: a default route learned from the IGP would
   never be preferred over a net route from learned EGP.

   Although the Internet topology, and consequently routing in the
   Internet, have evolved considerably since then, this slightly
   augmented version of the classic model has survived intact to this
   day in the Internet (except that BGP has replaced EGP).  Conceptually
   (and often in implementation) each router has a routing table and one
   or more routing protocol processes.  Each of these processes can add
   any entry that it pleases, and can delete or modify any entry that it
   has created.  When routing a packet, the router picks the best route
   using longest match, augmented with a policy mechanism to break ties.
   Although this augmented classic model has served us well, it has a
   number of shortcomings:

   o It ignores (although it could be augmented to consider) path
      characteristics such as quality of service and MTU.

   o It doesn't support routing protocols (such as OSPF and Integrated
      IS-IS) that require route lookup algorithms different than pure
      longest match.

   o There has not been a firm consensus on what the tie-breaking
      mechanism ought to be.  Tie-breaking mechanisms have often been
      found to be difficult if not impossible to configure in such a way
      that the router will always pick what the network manger considers
      to be the "correct" route.

E.2. Additional Pruning Rules

      Section [5.2.4.3] defined several pruning rules to use to select
      routes from the FIB.  There are other rules that could also be
      used.

      o OSPF Route Class
         Routing protocols that have areas or make a distinction between
         internal and external routes divide their routes into classes
         by the type of information used to calculate the route.  A
         route is always chosen from the most preferred class unless
         none is available, in which case one is chosen from the second
         most preferred class, and so on.  In OSPF, the classes (in
         order from most preferred to least preferred) are intra-area,
         inter-area, type 1 external (external routes with internal
         metrics), and type 2 external.  As an additional wrinkle, a



Baker                       Standards Track                   [Page 157]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


         router is configured to know what addresses ought to be
         accessible using intra-area routes, and will not use inter-
         area or external routes to reach these destinations even when
         no intra-area route is available.

         More precisely, we assume that each route has a class
         attribute, called route.class, which is assigned by the routing
         protocol.  The set of candidate routes is examined to determine
         if it contains any for which route.class = intra-area.  If so,
         all routes except those for which route.class = intra-area are
         discarded.  Otherwise, router checks whether the packet's
         destination falls within the address ranges configured for the
         local area.  If so, the entire set of candidate routes is
         deleted.  Otherwise, the set of candidate routes is examined to
         determine if it contains any for which route.class = inter-
         area.  If so, all routes except those for which route.class =
         inter-area are discarded.  Otherwise, the set of candidate
         routes is examined to determine if it contains any for which
         route.class = type 1 external.  If so, all routes except those
         for which route.class = type 1 external are discarded.

      o IS-IS Route Class
         IS-IS route classes work identically to OSPF's.  However, the
         set of classes defined by Integrated IS-IS is different, such
         that there isn't a one-to-one mapping between IS-IS route
         classes and OSPF route classes.  The route classes used by
         Integrated IS-IS are (in order from most preferred to least
         preferred) intra-area, inter-area, and external.

         The Integrated IS-IS internal class is equivalent to the OSPF
         internal class.  Likewise, the Integrated IS-IS external class
         is equivalent to OSPF's type 2 external class.  However,
         Integrated IS-IS does not make a distinction between inter-area
         routes and external routes with internal metrics - both are
         considered to be inter-area routes.  Thus, OSPF prefers true
         inter-area routes over external routes with internal metrics,
         whereas Integrated IS-IS gives the two types of routes equal
         preference.

      o IDPR Policy
         A specific case of Policy.  The IETF's Inter-domain Policy
         Routing Working Group is devising a routing protocol called
         Inter-Domain Policy Routing (IDPR) to support true policy-based
         routing in the Internet.  Packets with certain combinations of
         header attributes (such as specific combinations of source and
         destination addresses or special IDPR source route options) are
         required to use routes provided by the IDPR protocol.  Thus,
         unlike other Policy pruning rules, IDPR Policy would have to be



Baker                       Standards Track                   [Page 158]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


         applied before any other pruning rules except Basic Match.

         Specifically, IDPR Policy examines the packet being forwarded
         to ascertain if its attributes require that it be forwarded
         using policy-based routes.  If so, IDPR Policy deletes all
         routes not provided by the IDPR protocol.

E.3 Some Route Lookup Algorithms

      This section examines several route lookup algorithms that are in
      use or have been proposed.  Each is described by giving the
      sequence of pruning rules it uses.  The strengths and weaknesses
      of each algorithm are presented

E.3.1 The Revised Classic Algorithm

      The Revised Classic Algorithm is the form of the traditional
      algorithm that was discussed in Section [E.1].  The steps of this
      algorithm are:

      1.  Basic match
      2.  Longest match
      3.  Best metric
      4.  Policy

      Some implementations omit the Policy step, since it is needed only
      when routes may have metrics that are not comparable (because they
      were learned from different routing domains).

      The advantages of this algorithm are:

      (1) It is widely implemented.

      (2) Except for the Policy step (which an implementor can choose to
           make arbitrarily complex) the algorithm is simple both to
           understand and to implement.

      Its disadvantages are:

      (1) It does not handle IS-IS or OSPF route classes, and therefore
           cannot be used for Integrated IS-IS or OSPF.

      (2) It does not handle TOS or other path attributes.

      (3) The policy mechanisms are not standardized in any way, and are
           therefore are often implementation-specific.  This causes
           extra work for implementors (who must invent appropriate
           policy mechanisms) and for users (who must learn how to use



Baker                       Standards Track                   [Page 159]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


           the mechanisms. This lack of a standardized mechanism also
           makes it difficult to build consistent configurations for
           routers from different vendors. This presents a significant
           practical deterrent to multi-vendor interoperability.

      (4) The proprietary policy mechanisms currently provided by
           vendors are often inadequate in complex parts of the
           Internet.

      (5) The algorithm has not been written down in any generally
           available document or standard.  It is, in effect, a part of
           the Internet Folklore.

E.3.2 The Variant Router Requirements Algorithm

      Some Router Requirements Working Group members have proposed a
      slight variant of the algorithm described in the Section
      [5.2.4.3].  In this variant, matching the type of service
      requested is considered to be more important, rather than less
      important, than matching as much of the destination address as
      possible.  For example, this algorithm would prefer a default
      route that had the correct type of service over a network route
      that had the default type of service, whereas the algorithm in
      [5.2.4.3] would make the opposite choice.

      The steps of the algorithm are:

      1.  Basic match
      2.  Weak TOS
      3.  Longest match
      4.  Best metric
      5.  Policy

      Debate between the proponents of this algorithm and the regular
      Router Requirements Algorithm suggests that each side can show
      cases where its algorithm leads to simpler, more intuitive routing
      than the other's algorithm does.  This variant has the same set of
      advantages and disadvantages that the algorithm specified in
      [5.2.4.3] does, except that pruning on Weak TOS before pruning on
      Longest Match makes this algorithm less compatible with OSPF and
      Integrated IS-IS than the standard Router Requirements Algorithm.

E.3.3 The OSPF Algorithm

      OSPF uses an algorithm that is virtually identical to the Router
      Requirements Algorithm except for one crucial difference: OSPF
      considers OSPF route classes.




Baker                       Standards Track                   [Page 160]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


      The algorithm is:

      1.  Basic match
      2.  OSPF route class
      3.  Longest match
      4.  Weak TOS
      5.  Best metric
      6.  Policy

      Type of service support is not always present.  If it is not
      present then, of course, the fourth step would be omitted

      This algorithm has some advantages over the Revised Classic
      Algorithm:

      (1) It supports type of service routing.

      (2) Its rules are written down, rather than merely being a part of
           the Internet folklore.

      (3) It (obviously) works with OSPF.

      However, this algorithm also retains some of the disadvantages of
      the Revised Classic Algorithm:

      (1) Path properties other than type of service (e.g., MTU) are
           ignored.

      (2) As in the Revised Classic Algorithm, the details (or even the
           existence) of the Policy step are left to the discretion of
           the implementor.

      The OSPF Algorithm also has a further disadvantage (which is not
      shared by the Revised Classic Algorithm).  OSPF internal (intra-
      area or inter-area) routes are always considered to be superior to
      routes learned from other routing protocols, even in cases where
      the OSPF route matches fewer bits of the destination address.
      This is a policy decision that is inappropriate in some networks.

      Finally, it is worth noting that the OSPF Algorithm's TOS support
      suffers from a deficiency in that routing protocols that support
      TOS are implicitly preferred when forwarding packets that have
      non-zero TOS values.  This may not be appropriate in some cases.








Baker                       Standards Track                   [Page 161]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


E.3.4 The Integrated IS-IS Algorithm

   Integrated IS-IS uses an algorithm that is similar to but not quite
   identical to the OSPF Algorithm.  Integrated IS-IS uses a different
   set of route classes, and differs slightly in its handling of type of
   service.  The algorithm is:

   1.  Basic Match
   2.  IS-IS Route Classes
   3.  Longest Match
   4.  Weak TOS
   5.  Best Metric
   6.  Policy

   Although Integrated IS-IS uses Weak TOS, the protocol is only capable
   of carrying routes for a small specific subset of the possible values
   for the TOS field in the IP header.  Packets containing other values
   in the TOS field are routed using the default TOS.

   Type of service support is optional; if disabled, the fourth step
   would be omitted.  As in OSPF, the specification does not include the
   Policy step.

   This algorithm has some advantages over the Revised Classic
   Algorithm:

   (1) It supports type of service routing.
   (2) Its rules are written down, rather than merely being a part of
        the Internet folklore.
   (3) It (obviously) works with Integrated IS-IS.

   However, this algorithm also retains some of the disadvantages of the
   Revised Classic Algorithm:

   (1) Path properties other than type of service (e.g., MTU) are
        ignored.
   (2) As in the Revised Classic Algorithm, the details (or even the
        existence) of the Policy step are left to the discretion of the
        implementor.
   (3) It doesn't work with OSPF because of the differences between IS-
        IS route classes and OSPF route classes.  Also, because IS-IS
        supports only a subset of the possible TOS values, some obvious
        implementations of the Integrated IS-IS algorithm would not
        support OSPF's interpretation of TOS.

   The Integrated IS-IS Algorithm also has a further disadvantage (which
   is not shared by the Revised Classic Algorithm): IS-IS internal
   (intra-area or inter-area) routes are always considered to be



Baker                       Standards Track                   [Page 162]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   superior to routes learned from other routing protocols, even in
   cases where the IS-IS route matches fewer bits of the destination
   address and doesn't provide the requested type of service.  This is a
   policy decision that may not be appropriate in all cases.

   Finally, it is worth noting that the Integrated IS-IS Algorithm's TOS
   support suffers from the same deficiency noted for the OSPF
   Algorithm.

Security Considerations

   Although the focus of this document is interoperability rather than
   security, there are obviously many sections of this document that
   have some ramifications on network security.

   Security means different things to different people.  Security from a
   router's point of view is anything that helps to keep its own
   networks operational and in addition helps to keep the Internet as a
   whole healthy.  For the purposes of this document, the security
   services we are concerned with are denial of service, integrity, and
   authentication as it applies to the first two.  Privacy as a security
   service is important, but only peripherally a concern of a router -
   at least as of the date of this document.

   In several places in this document there are sections entitled ...
   Security Considerations.  These sections discuss specific
   considerations that apply to the general topic under discussion.

   Rarely does this document say do this and your router/network will be
   secure.  More likely, it says this is a good idea and if you do it,
   it *may* improve the security of the Internet and your local system
   in general.

   Unfortunately, this is the state-of-the-art AT THIS TIME.  Few if any
   of the network protocols a router is concerned with have reasonable,
   built-in security features.  Industry and the protocol designers have
   been and are continuing to struggle with these issues.  There is
   progress, but only small baby steps such as the peer-to-peer
   authentication available in the BGP and OSPF routing protocols.

   In particular, this document notes the current research into
   developing and enhancing network security.  Specific areas of
   research, development, and engineering that are underway as of this
   writing (December 1993) are in IP Security, SNMP Security, and common
   authentication technologies.

   Notwithstanding all the above, there are things both vendors and
   users can do to improve the security of their router.  Vendors should



Baker                       Standards Track                   [Page 163]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   get a copy of Trusted Computer System Interpretation [INTRO:8].  Even
   if a vendor decides not to submit their device for formal
   verification under these guidelines, the publication provides
   excellent guidance on general security design and practices for
   computing devices.

APPENDIX F: HISTORICAL ROUTING PROTOCOLS

   Certain routing protocols are common in the Internet, but the authors
   of this document cannot in good conscience recommend their use.  This
   is not because they do not work correctly, but because the
   characteristics of the Internet assumed in their design (simple
   routing, no policy, a single "core router" network under common
   administration, limited complexity, or limited network diameter) are
   not attributes of today's Internet.  Those parts of the Internet that
   still use them are generally limited "fringe" domains with limited
   complexity.

   As a matter of good faith, collected wisdom concerning their
   implementation is recorded in this section.

F.1 EXTERIOR GATEWAY PROTOCOL - EGP

F.1.1 Introduction

   The Exterior Gateway Protocol (EGP) specifies an EGP that is used to
   exchange reachability information between routers of the same or
   differing autonomous systems.  EGP is not considered a routing
   protocol since there is no standard interpretation (i.e. metric) for
   the distance fields in the EGP update message, so distances are
   comparable only among routers of the same AS.  It is however designed
   to provide high-quality reachability information, both about neighbor
   routers and about routes to non-neighbor routers.

   EGP is defined by [ROUTE:6].  An implementor almost certainly wants
   to read [ROUTE:7] and [ROUTE:8] as well, for they contain useful
   explanations and background material.

   DISCUSSION
      The present EGP specification has serious limitations, most
      importantly a restriction that limits routers to advertising only
      those networks that are reachable from within the router's
      autonomous system.  This restriction against propagating third
      party EGP information is to prevent long-lived routing loops.
      This effectively limits EGP to a two-level hierarchy.

      RFC-975 is not a part of the EGP specification, and should be
      ignored.



Baker                       Standards Track                   [Page 164]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


F.1.2 Protocol Walk-through

      Indirect Neighbors: RFC-888, page 26

         An implementation of EGP MUST include indirect neighbor
         support.

      Polling Intervals: RFC-904, page 10

         The interval between Hello command retransmissions and the
         interval between Poll retransmissions SHOULD be configurable
         but there MUST be a minimum value defined.

         The interval at which an implementation will respond to Hello
         commands and Poll commands SHOULD be configurable but there
         MUST be a minimum value defined.

      Network Reachability: RFC-904, page 15

   An implementation MUST default to not providing the external list of
   routers in other autonomous systems; only the internal list of
   routers together with the nets that are reachable through those
   routers should be included in an Update Response/Indication packet.
   However, an implementation MAY elect to provide a configuration
   option enabling the external list to be provided.  An implementation
   MUST NOT include in the external list routers that were learned
   through the external list provided by a router in another autonomous
   system.  An implementation MUST NOT send a network back to the
   autonomous system from which it is learned, i.e.  it MUST do split-
   horizon on an autonomous system level.

   If more than 255 internal or 255 external routers need to be
   specified in a Network Reachability update, the networks reachable
   from routers that can not be listed MUST be merged into the list for
   one of the listed routers.  Which of the listed routers is chosen for
   this purpose SHOULD be user configurable, but SHOULD default to the
   source address of the EGP update being generated.

   An EGP update contains a series of blocks of network numbers, where
   each block contains a list of network numbers reachable at a
   particular distance through a particular router.  If more than 255
   networks are reachable at a particular distance through a particular
   router, they are split into multiple blocks (all of which have the
   same distance).  Similarly, if more than 255 blocks are required to
   list the networks reachable through a particular router, the router's
   address is listed as many times as necessary to include all the
   blocks in the update.




Baker                       Standards Track                   [Page 165]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


Unsolicited Updates: RFC-904, page 16

   If a network is shared with the peer, an implementation MUST send an
   unsolicited update upon entry to the Up state if the source network
   is the shared network.

Neighbor Reachability: RFC-904, page 6, 13-15

   The table on page 6 that describes the values of j and k (the
   neighbor up and down thresholds) is incorrect.  It is reproduced
   correctly here:

      Name    Active  Passive Description
      -----------------------------------------------
       j         3       1    neighbor-up threshold
       k         1       0    neighbor-down threshold

   The value for k in passive mode also specified incorrectly in RFC-
   904, page 14 The values in parenthesis should read:

      (j = 1, k = 0, and T3/T1 = 4)

   As an optimization, an implementation can refrain from sending a
   Hello command when a Poll is due.  If an implementation does so, it
   SHOULD provide a user configurable option to disable this
   optimization.

Abort timer: RFC-904, pages 6, 12, 13

   An EGP implementation MUST include support for the abort timer (as
   documented in section 4.1.4 of RFC-904).  An implementation SHOULD
   use the abort timer in the Idle state to automatically issue a Start
   event to restart the protocol machine.  Recommended values are P4 for
   a critical error (Administratively prohibited, Protocol Violation and
   Parameter Problem) and P5 for all others.  The abort timer SHOULD NOT
   be started when a Stop event was manually initiated (such as through
   a network management protocol).

Cease command received in Idle state: RFC-904, page 13

   When the EGP state machine is in the Idle state, it MUST reply to
   Cease commands with a Cease-ack response.

Hello Polling Mode: RFC-904, page 11

   An EGP implementation MUST include support for both active and
   passive polling modes.




Baker                       Standards Track                   [Page 166]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


Neighbor Acquisition Messages: RFC-904, page 18

   As noted the Hello and Poll Intervals should only be present in
   Request and Confirm messages.  Therefore the length of an EGP
   Neighbor Acquisition Message is 14 bytes for a Request or Confirm
   message and 10 bytes for a Refuse, Cease or Cease-ack message.
   Implementations MUST NOT send 14 bytes for Refuse, Cease or Cease-ack
   messages but MUST allow for implementations that send 14 bytes for
   these messages.

Sequence Numbers: RFC-904, page 10

   Response or indication packets received with a sequence number not
   equal to S MUST be discarded.  The send sequence number S MUST be
   incremented just before the time a Poll command is sent and at no
   other times.

F.2 ROUTING INFORMATION PROTOCOL - RIP

F.2.1 Introduction

   RIP is specified in [ROUTE:3].  Although RIP is still quite important
   in the Internet, it is being replaced in sophisticated applications
   by more modern IGPs such as the ones described above.  A router
   implementing RIP SHOULD implement RIP Version 2 [ROUTE:?], as it
   supports CIDR routes.  If occasional access networking is in use, a
   router implementing RIP SHOULD implement Demand RIP [ROUTE:?].

   Another common use for RIP is as a router discovery protocol.
   Section [4.3.3.10] briefly touches upon this subject.

F.2.2 Protocol Walk-Through

   Dealing with changes in topology: [ROUTE:3], page 11

        An implementation of RIP MUST provide a means for timing out
        routes.  Since messages are occasionally lost, implementations
        MUST NOT invalidate a route based on a single missed update.

        Implementations MUST by default wait six times the update
        interval before invalidating a route.  A router MAY have
        configuration options to alter this value.

   DISCUSSION
      It is important to routing stability that all routers in a RIP
      autonomous system use similar timeout value for invalidating
      routes, and therefore it is important that an implementation
      default to the timeout value specified in the RIP specification.



Baker                       Standards Track                   [Page 167]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


      However, that timeout value is too conservative in environments
      where packet loss is reasonably rare.  In such an environment, a
      network manager may wish to be able to decrease the timeout period
      to promote faster recovery from failures.

   IMPLEMENTATION
      There is a very simple mechanism that a router may use to meet the
      requirement to invalidate routes promptly after they time out.
      Whenever the router scans the routing table to see if any routes
      have timed out, it also notes the age of the least recently
      updated route that has not yet timed out.  Subtracting this age
      from the timeout period gives the amount of time until the router
      again needs to scan the table for timed out routes.

Split Horizon: [ROUTE:3], page 14-15

   An implementation of RIP MUST implement split horizon, a scheme used
   for avoiding problems caused by including routes in updates sent to
   the router from which they were learned.

   An implementation of RIP SHOULD implement Split horizon with poisoned
   reverse, a variant of split horizon that includes routes learned from
   a router sent to that router, but sets their metric to infinity.
   Because of the routing overhead that may be incurred by implementing
   split horizon with poisoned reverse, implementations MAY include an
   option to select whether poisoned reverse is in effect.  An
   implementation SHOULD limit the time in which it sends reverse routes
   at an infinite metric.

   IMPLEMENTATION
      Each of the following algorithms can be used to limit the time for
      which poisoned reverse is applied to a route.  The first algorithm
      is more complex but does a more thorough job of limiting poisoned
      reverse to only those cases where it is necessary.

      The goal of both algorithms is to ensure that poison reverse is
      done for any destination whose route has changed in the last Route
      Lifetime (typically 180 seconds), unless it can be sure that the
      previous route used the same output interface.  The Route Lifetime
      is used because that is the amount of time RIP will keep around an
      old route before declaring it stale.

      The time intervals (and derived variables) used in the following
      algorithms are as follows:

      Tu The Update Timer; the number of seconds between RIP updates.
           This typically defaults to 30 seconds.




Baker                       Standards Track                   [Page 168]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


      Rl The Route Lifetime, in seconds.  This is the amount of time
           that a route is presumed to be good, without requiring an
           update.  This typically defaults to 180 seconds.

      Ul The Update Loss; the number of consecutive updates that have to
           be lost or fail to mention a route before RIP deletes the
           route.  Ul is calculated to be (Rl/Tu)+1.  The +1 is to
           account for the fact that the first time the ifcounter is
           decremented will be less than Tu seconds after it is
           initialized.  Typically, Ul will be 7: (180/30)+1.


      In The value to set ifcounter to when a destination is newly
           learned.  This value is Ul-4, where the 4 is RIP's garbage
           collection timer/30

      The first algorithm is:

      - Associated with each destination is a counter, called the
         ifcounter below.  Poison reverse is done for any route whose
         destination's ifcounter is greater than zero.

      - After a regular (not triggered or in response to a request)
         update is sent, all the non-zero ifcounters are decremented by
         one.

      - When a route to a destination is created, its ifcounter is set
         as follows:

         - If the new route is superseding a valid route, and the old
            route used a different (logical) output interface, then the
            ifcounter is set to Ul.

         - If the new route is superseding a stale route, and the old
            route used a different (logical) output interface, then the
            ifcounter is set to MAX(0, Ul - INT(seconds that the route
            has been stale/Ut).

         - If there was no previous route to the destination, the
            ifcounter is set to In.

         - Otherwise, the ifcounter is set to zero

      - RIP also maintains a timer, called the resettimer below.  Poison
         reverse is done on all routes whenever resettimer has not
         expired (regardless of the ifcounter values).





Baker                       Standards Track                   [Page 169]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


      - When RIP is started, restarted, reset, or otherwise has its
         routing table cleared, it sets the resettimer to go off in Rl
         seconds.

      The second algorithm is identical to the first except that:

      - The rules which set the ifcounter to non-zero values are changed
         to always set it to Rl/Tu, and

      - The resettimer is eliminated.

 Triggered updates: [ROUTE:3], page 15-16; page 29

      Triggered updates (also called flash updates) are a mechanism for
      immediately notifying a router's neighbors when the router adds or
      deletes routes or changes their metrics.  A router MUST send a
      triggered update when routes are deleted or their metrics are
      increased.  A router MAY send a triggered update when routes are
      added or their metrics decreased.

      Since triggered updates can cause excessive routing overhead,
      implementations MUST use the following mechanism to limit the
      frequency of triggered updates:

      (1) When a router sends a triggered update, it sets a timer to a
           random time between one and five seconds in the future.  The
           router must not generate additional triggered updates before
           this timer expires.

      (2) If the router would generate a triggered update during this
           interval it sets a flag indicating that a triggered update is
           desired.  The router also logs the desired triggered update.

      (3) When the triggered update timer expires, the router checks the
           triggered update flag.  If the flag is set then the router
           sends a single triggered update which includes all the
           changes that were logged.  The router then clears the flag
           and, since a triggered update was sent, restarts this
           algorithm.

      (4) The flag is also cleared whenever a regular update is sent.

      Triggered updates SHOULD include all routes that have changed
      since the most recent regular (non-triggered) update.  Triggered
      updates MUST NOT include routes that have not changed since the
      most recent regular update.





Baker                       Standards Track                   [Page 170]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   DISCUSSION
      Sending all routes, whether they have changed recently or not, is
      unacceptable in triggered updates because the tremendous size of
      many Internet routing tables could otherwise result in
      considerable bandwidth being wasted on triggered updates.

Use of UDP: [ROUTE:3], page 18-19.

   RIP packets sent to an IP broadcast address SHOULD have their initial
   TTL set to one.

   Note that to comply with Section [6.1] of this memo, a router SHOULD
   use UDP checksums in RIP packets that it originates, MUST discard RIP
   packets received with invalid UDP checksums, but MUST NOT discard
   received RIP packets simply because they do not contain UDP
   checksums.

Addressing Considerations: [ROUTE:3], page 22

   A RIP implementation SHOULD support host routes.  If it does not, it
   MUST (as described on page 27 of [ROUTE:3]) ignore host routes in
   received updates.  A router MAY log ignored hosts routes.

   The special address 0.0.0.0 is used to describe a default route.  A
   default route is used as the route of last resort (i.e., when a route
   to the specific net does not exist in the routing table).  The router
   MUST be able to create a RIP entry for the address 0.0.0.0.

Input Processing - Response: [ROUTE:3], page 26

   When processing an update, the following validity checks MUST be
   performed:

   o The response MUST be from UDP port 520.

   o The source address MUST be on a directly connected subnet (or on a
      directly connected, non-subnetted network) to be considered valid.

   o The source address MUST NOT be one of the router's addresses.

   DISCUSSION
      Some networks, media, and interfaces allow a sending node to
      receive packets that it broadcasts.  A router must not accept its
      own packets as valid routing updates and process them.  The last
      requirement prevents a router from accepting its own routing
      updates and processing them (on the assumption that they were sent
      by some other router on the network).




Baker                       Standards Track                   [Page 171]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   An implementation MUST NOT replace an existing route if the metric
   received is equal to the existing metric except in accordance with
   the following heuristic.

   An implementation MAY choose to implement the following heuristic to
   deal with the above situation.  Normally, it is useless to change the
   route to a network from one router to another if both are advertised
   at the same metric.  However, the route being advertised by one of
   the routers may be in the process of timing out.  Instead of waiting
   for the route to timeout, the new route can be used after a specified
   amount of time has elapsed.  If this heuristic is implemented, it
   MUST wait at least halfway to the expiration point before the new
   route is installed.

F.2.3 Specific Issues


RIP Shutdown

     An implementation of RIP SHOULD provide for a graceful shutdown
     using the following steps:

     (1) Input processing is terminated,

     (2) Four updates are generated at random intervals of between two
          and four seconds, These updates contain all routes that were
          previously announced, but with some metric changes.  Routes
          that were being announced at a metric of infinity should
          continue to use this metric.  Routes that had been announced
          with a non-infinite metric should be announced with a metric
          of 15 (infinity - 1).

   DISCUSSION
      The metric used for the above really ought to be 16 (infinity);
      setting it to 15 is a kludge to avoid breaking certain old hosts
      that wiretap the RIP protocol.  Such a host will (erroneously)
      abort a TCP connection if it tries to send a datagram on the
      connection while the host has no route to the destination (even if
      the period when the host has no route lasts only a few seconds
      while RIP chooses an alternate path to the destination).

RIP Split Horizon and Static Routes

   Split horizon SHOULD be applied to static routes by default.  An
   implementation SHOULD provide a way to specify, per static route,
   that split horizon should not be applied to this route.





Baker                       Standards Track                   [Page 172]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


F.3 GATEWAY TO GATEWAY PROTOCOL - GGP

   The Gateway to Gateway protocol is considered obsolete and SHOULD NOT
   be implemented.

Acknowledgments

   O that we now had here
   But one ten thousand of those men in England
   That do no work to-day!

   What's he that wishes so?
   My cousin Westmoreland? No, my fair cousin:
   If we are mark'd to die, we are enow
   To do our country loss; and if to live,
   The fewer men, the greater share of honour.
   God's will! I pray thee, wish not one man more.
   By Jove, I am not covetous for gold,
   Nor care I who doth feed upon my cost;
   It yearns me not if men my garments wear;
   Such outward things dwell not in my desires:
   But if it be a sin to covet honour,
   I am the most offending soul alive.
   No, faith, my coz, wish not a man from England:
   God's peace! I would not lose so great an honour
   As one man more, methinks, would share from me
   For the best hope I have. O, do not wish one more!
   Rather proclaim it, Westmoreland, through my host,
   That he which hath no stomach to this fight,
   Let him depart; his passport shall be made
   And crowns for convoy put into his purse:
   We would not die in that man's company
   That fears his fellowship to die with us.
   This day is called the feast of Crispian:
   He that outlives this day, and comes safe home,
   Will stand a tip-toe when the day is named,
   And rouse him at the name of Crispian.
   He that shall live this day, and see old age,
   Will yearly on the vigil feast his neighbours,
   And say 'To-morrow is Saint Crispian:'
   Then will he strip his sleeve and show his scars.
   And say 'These wounds I had on Crispin's day.'
   Old men forget: yet all shall be forgot,
   But he'll remember with advantages
   What feats he did that day: then shall our names.
   Familiar in his mouth as household words
   Harry the king, Bedford and Exeter,
   Warwick and Talbot, Salisbury and Gloucester,



Baker                       Standards Track                   [Page 173]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   Be in their flowing cups freshly remember'd.
   This story shall the good man teach his son;
   And Crispin Crispian shall ne'er go by,
   From this day to the ending of the world,
   But we in it shall be remember'd;
   We few, we happy few, we band of brothers;
   For he to-day that sheds his blood with me
   Shall be my brother; be he ne'er so vile,
   This day shall gentle his condition:
   And gentlemen in England now a-bed
   Shall think themselves accursed they were not here,
   And hold their manhoods cheap whiles any speaks
   That fought with us upon Saint Crispin's day.

                                   -- William Shakespeare

   This memo is a product of the IETF's Router Requirements Working
   Group.  A memo such as this one is of necessity the work of many more
   people than could be listed here.  A wide variety of vendors, network
   managers, and other experts from the Internet community graciously
   contributed their time and wisdom to improve the quality of this
   memo.  The editor wishes to extend sincere thanks to all of them.

   The current editor also wishes to single out and extend his heartfelt
   gratitude and appreciation to the original editor of this document;
   Philip Almquist.  Without Philip's work, both as the original editor
   and as the Chair of the working group, this document would not have
   been produced.  He also wishes to express deep and heartfelt
   gratitude to the previous editor, Frank Kastenholz.  Frank changed
   the original document from a collection of information to a useful
   description of IP technology - in his words, a "snapshot" of the
   technology in 1991.  One can only hope that this snapshot, of the
   technology in 1994, is as clear.

   Philip Almquist, Jeffrey Burgan, Frank Kastenholz, and Cathy
   Wittbrodt each wrote major chapters of this memo.  Others who made
   major contributions to the document included Bill Barns, Steve
   Deering, Kent England, Jim Forster, Martin Gross, Jeff Honig, Steve
   Knowles, Yoni Malachi, Michael Reilly, and Walt Wimer.

   Additional text came from Andy Malis, Paul Traina, Art Berggreen,
   John Cavanaugh, Ross Callon, John Lekashman, Brian Lloyd, Gary
   Malkin, Milo Medin, John Moy, Craig Partridge, Stephanie Price, Yakov
   Rekhter, Steve Senum, Richard Smith, Frank Solensky, Rich Woundy, and
   others who have been inadvertently overlooked.

   Some of the text in this memo has been (shamelessly) plagiarized from
   earlier documents, most notably RFC-1122 by Bob Braden and the Host



Baker                       Standards Track                   [Page 174]

RFC 1812         Requirements for IP Version 4 Routers         June 1995


   Requirements Working Group, and RFC-1009 by Bob Braden and Jon
   Postel.  The work of these earlier authors is gratefully
   acknowledged.

   Jim Forster was a co-chair of the Router Requirements Working Group
   during its early meetings, and was instrumental in getting the group
   off to a good start.  Jon Postel, Bob Braden, and Walt Prue also
   contributed to the success by providing a wealth of good advice
   before the group's first meeting.  Later on, Phill Gross, Vint Cerf,
   and Noel Chiappa all provided valuable advice and support.

   Mike St.  Johns coordinated the Working Group's interactions with the
   security community, and Frank Kastenholz coordinated the Working
   Group's interactions with the network management area.  Allison
   Mankin and K.K.  Ramakrishnan provided expertise on the issues of
   congestion control and resource allocation.

   Many more people than could possibly be listed or credited here
   participated in the deliberations of the Router Requirements Working
   Group, either through electronic mail or by attending meetings.
   However, the efforts of Ross Callon and Vince Fuller in sorting out
   the difficult issues of route choice and route leaking are especially
   acknowledged.

   The editor thanks his employer, Cisco Systems, for allowing him to
   spend the time necessary to produce the 1994 snapshot.

Editor's Address

   The address of the current editor of this document is

      Fred Baker
      Cisco Systems
      519 Lado Drive
      Santa Barbara, California 93111
      USA

      Phone:+1 805-681-0115

      EMail: fred@cisco.com











Baker                       Standards Track                   [Page 175]