Return to the Products Page
  homesearchagentssupportask xilinxmap

Algorithm Change Notice ACN99001

Subject: Xilinx is making a change to the XC9500XL to improve yields. This will require a change in the programming algorithm for XC9500XL Family: XC9536XL, XC9572XL, XC95144XL, and XC95288XL.

Change Description:  Xilinx is changing to a -02 on the JTAG ID register. This code is read by JTAG Programmer and other third party JTAG tools. 

Additionally, the Product Code used by the HW-130 and third party programmers has changed and are: 

9536XL 30 Hex 
9572XL 31 Hex 
95144XL 32 Hex 
95288XL 33 Hex
Product Change: This is a yield enhancement. It does not affect any electrical characteristic of the devices with the exception of the programming voltages. These voltages can only be accessed externally in a special mode in a dedicated parallel programming environment such as the Xilinx HW130, or programmers offered by manufacturers such as BP Microsystems and Data I/O. 

Reason for Change: Yield enhancement

Key Dates:
Product shipments began on August 19.
Shipments of older devices will continue until inventories are exhausted.

Response: 
Users have different actions depending on the programming environment: 

Xilinx HW-130 Programmer:
Software Version 4.63 (9/04/1999) 
Available from the Xilinx ftp site at:
     ftp://ftp.xilinx.com/pub/swhelp/programmer/hw130w32.exeInternet Link

JTAGProgrammer:
1. Version M2.1i
     OR 
2. M1.5 (and later) with the new (Rev. 2.0) BSDL files installed. These BSDL files can currently be found at:
     http://www.xilinx.com/techdocs/htm_index/sw_bsdl.htm

The file name is 'xc9500xl.zip' and contains the following BSDL files for this version of the silicon:
     xc95144xl_v2.bsd 
     xc95288xl_v2.bsd 
     xc9536xl_v2.bsd 
     xc9572xl_v2.bsd 

3rd Party Programmer Customers: 

BP Microsystems - all programmers 
Use Version 3.43 
This software can be found at; 
     http://www.bpmicro.com/Internet Link

Data-IO - Unisys family of programmers 
The 'extended algorithm' software for the XC9500XL family will be posted by 9/15/99 and will be available at; 
     ftp://ftp.data-io.com/dataio/betaalgs/59_9500xl.exeInternet Link
          OR
     ftp://ftp.data-io.com/dataio/betaalgs/60_9500xl.exeInternet Link

Other programmer vendors
If your customers are using other programmer vendors, please refer to the appropriate vendor for support information. 

ATE customers: 
GenRad, Teradyne, HP3070, iFR:

No changes are required if the customer created the SVF files (which are translated to the different ATE formats) using JTAGProgrammer version M1.5 or greater.

If an earlier version of JTAGProgrammer was used to create the SVF files, please upgrade to M2.1i (or M2.1i SP1) and re-generate the SVF files and the tester vectors. 

Embedded micro controller customers: 
No changes are required if the customer created the SVF files (which are translated to XSVF using the SVF2XSVF translator) using JTAGProgrammer version M1.5 or greater. 

If an earlier version of JTAGProgrammer was used to create the SVF files, please upgrade to M2.1i (or M2.1i SP1) and regenerate the SVF and XSVF files.