Internet Draft
Network Working Group J. Cucchiara
Internet-Draft IronBridge Networks
Expires March 2000 H. Sjostrand
Ericsson
J. Luciani
Nortel Networks
October 1999
Definitions of Managed Objects for
the Multiprotocol Label Switching, Label Distribution Protocol (LDP)
<draft-ietf-mpls-ldp-mib-02.txt>
Status of this Memo
This document is an Internet-Draft and is in full conformance with
all provisions of Section 10 of RFC 2026. Internet-Drafts are
working documents of the Internet Engineering Task Force (IETF), its
areas, and its working groups. Note that other groups may also
distribute working documents as Internet-Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress".
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html
Distribution of this document is unlimited. Please send comments to
the Multiprotocol Label Switching (mpls) Working Group,
.
Copyright Notice
Copyright (C) The Internet Society (1999). All Rights Reserved.
Abstract
This memo defines a portion of the Management Information Base (MIB)
for use with network management protocols in the Internet community.
In particular, it describes managed objects for the Multiprotocol
Label Switching, Label Distribution Protocol (LDP).
Expires April 2000 [Page 1]
INTERNET-DRAFT MPLS LDP MIB October 1999
Table of Contents
1 Introduction ................................................. 3
2 The SNMP Management Framework ................................ 3
3 Structure of the MIB ......................................... 5
3.1 Overview ................................................... 5
3.2 Interface Indexing ......................................... 5
3.3 Future Considerations ...................................... 5
3.4 Discussion of MIB Groups ................................... 6
3.5 The MPLS LDP General Group ................................. 6
3.5.1 The Label Distribution Protocol's Entity Table ........... 6
3.5.2 The Label Distribution Protocol's Entity ATM Objects ..... 6
Objects ................................................... 6
Table ..................................................... 7
3.5.5 The LDP Peer Table ....................................... 7
3.5.6 The LDP Session Table .................................... 7
3.5.7 The LDP ATM Session Table ................................ 7
3.5.8 The LDP Frame Relay Session Table ........................ 7
3.5.9 The LDP Session Statistics Table ......................... 7
3.5.10 The LDP Session Peer Address Table ...................... 8
3.5.11 The LDP Adjacencies Table ............................... 8
3.5.12 The LDP Label Information Base (LIB) Table .............. 8
3.5.13 The LDP FEC Table ....................................... 8
3.6 The LDP Notifications Group ................................ 8
3.6.1 LDP Notifications ........................................ 8
4 MPLS Label Distribution Protocol MIB Definitions ............. 8
5 Revision History ............................................. 45
5.1 Changes from <draft-ietf-mpls-ldp-mib-01.txt> .............. 45
5.2 Changes from <draft-ietf-mpls-ldp-mib-00.txt> .............. 46
6 TO DO List ................................................... 47
7 Acknowledgments .............................................. 47
8 References ................................................... 48
9 Security Considerations ...................................... 50
10 Authors' Addresses .......................................... 50
11 Full Copyright Statement .................................... 51
12 IANA Address Family Numbers MIB ............................. 51
Expires April 2000 [Page 2]
INTERNET-DRAFT MPLS LDP MIB October 1999
1. Introduction
This memo defines a portion of the Management Information Base (MIB)
for use with network management protocols in the Internet community.
In particular, it describes managed objects for the Multiprotocol
Label Switching, Label Distribution Protocol (LDP) [18].
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [22].
2. The SNMP Management Framework
The SNMP Management Framework presently consists of five major
components:
o An overall architecture, described in RFC 2571 [RFC2571].
o Mechanisms for describing and naming objects and events for the
purpose of management. The first version of this Structure of
Management Information (SMI) is called SMIv1 and described in
STD 16, RFC 1155 [RFC1155], STD 16, RFC 1212 [RFC1212] and RFC
1215 [RFC1215]. The second version, called SMIv2, is described
in STD 58, RFC 2578 [RFC2578], RFC 2579 [RFC2579] and RFC 2580
[RFC2580].
o Message protocols for transferring management information. The
first version of the SNMP message protocol is called SNMPv1 and
described in STD 15, RFC 1157 [RFC1157]. A second version of the
SNMP message protocol, which is not an Internet standards track
protocol, is called SNMPv2c and described in RFC 1901 [RFC1901]
and RFC 1906 [RFC1906]. The third version of the message
protocol is called SNMPv3 and described in RFC 1906 [RFC1906],
RFC 2572 [RFC2572] and RFC 2574 [RFC2574].
o Protocol operations for accessing management information. The
first set of protocol operations and associated PDU formats is
described in STD 15, RFC 1157 [RFC1157]. A second set of
protocol operations and associated PDU formats is described in
RFC 1905 [RFC1905].
o A set of fundamental applications described in RFC 2573
[RFC2573] and the view-based access control mechanism described
in RFC 2575 [RFC2575].
A more detailed introduction to the current SNMP Management Framework
can be found in RFC 2570 [RFC2570].
Managed objects are accessed via a virtual information store, termed
Expires April 2000 [Page 3]
INTERNET-DRAFT MPLS LDP MIB October 1999
the Management Information Base or MIB. Objects in the MIB are
defined using the mechanisms defined in the SMI.
This memo specifies a MIB module that is compliant to the SMIv2. A
MIB conforming to the SMIv1 can be produced through the appropriate
translations. The resulting translated MIB must be semantically
equivalent, except where objects or events are omitted because no
translation is possible (use of Counter64). Some machine readable
information in SMIv2 will be converted into textual descriptions in
SMIv1 during the translation process. However, this loss of machine
readable information is not considered to change the semantics of the
MIB.
Expires April 2000 [Page 4]
INTERNET-DRAFT MPLS LDP MIB October 1999
3. Structure of the MIB
This memo defines a portion of the Management Information Base (MIB)
for use with network management protocols in the Internet community.
In particular, it describes managed objects for the Multiprotocol
Label Switching, Label Distribution Protocol (LDP) as defined in
[18].
3.1. Overview
The MIB provides objects to configure/set-up potential LDP sessions
on a specific LSR. A table is used to configure potential LDP
Sessions, where each row in the table initiates an LDP Session. This
is the mplsLdpEntityTable.
Another table, the mplsLdpPeerTable, is a read-only table which
records information learned via discovery. Each row in the Peer
Table represents a peer.
A third table is used to show the actual sessions which have been, or
are in the process of being established. Each row represents a
specific session between an Entity (on this LSR) and a peer. The
following figure demonstrates these relationships:
Entity Peer
------------ ------------
| | | |
------------ -------------
| | -------------- | |
------------ -----> | | <----- ------------
--------------
Session
3.2. Interface Indexing
Interface Indexes as specified in [29] are used in the MIB. The
descriptions of the ifIndexes denote which ifIndex is being used.
NOTE: the use of ifIndex is for actual existing connections.
3.3. Future Considerations
The following aspects are not addressed in this document: VPN issues
(i.e. potential MIB objects such as the VPN Identifier are not
included at this time), and lastly, multicast issues are not
discussed.
Some of these issues need further clarification before adding to the
Expires April 2000 [Page 5]
INTERNET-DRAFT MPLS LDP MIB October 1999
MIB.
3.4. Discussion of MIB Groups
Currently, there are four groups: the MPLS LDP General Group, the
MPLS LDP ATM Group, the MPLS LDP Frame Relay Group and the MPLS LDP
Notifications Group. The MPLS LDP General Group and the MPLS LDP
Notifications Group should always be supported. The MPLS LDP ATM
Group is specific to ATM and should be supported only if LDP is using
ATM. Likewise, the MPLS LDP Frame Relay group is specific to Frame
Relay and should be supported only if LDP is using Frame Relay.
3.5. The MPLS LDP General Group
This group contains information about the specific LDP Entities which
are associated with this agent. Each LSR must have one LDP Entity.
3.5.1. The Label Distribution Protocol's Entity Table
The LDP Entity Table provides a way to configure the LSR for using
LDP. There must be at least one LDP Entity for the LSR to support
LDP.
Each entry/row in this table represents a single LDP Entity.
3.5.2. The Label Distribution Protocol's Entity ATM Objects
There exists two tables to configure LDP for using ATM. These tables
are the mplsLdpEntityAtmParmsTable and the
mplsLdpEntityConfAtmLabelRangeTable.
The mplsLdpEntityAtmParmsTable provides a way to configure
information which would be contained in the 'Optional Paramer'
portion of an LDP PDU Initialization Message.
The mplsLdpEntityConfAtmLabelRangeTable provides a way to configure
information which would be contained in the 'ATM Label Range
Components' portion of an LDP PDU Intialization Message.
3.5.3. The Label Distribution Protocol's Entity Frame Relay Objects
There exists two tables to configure LDP for using Frame Relay.
These tables are the mplsLdpEntityFrameRelayParmsTable and the
mplsLdpEntityConfFrLabelRangeTable.
The mplsLdpEntityFrameRelayParmsTable provides a way to configure
Expires April 2000 [Page 6]
INTERNET-DRAFT MPLS LDP MIB October 1999
information which would be contained in the 'Optional Paramer'
portion of an LDP PDU Initialization Message.
The mplsLdpEntityConfFrLabelRangeTable provides a way to configure
information which would be contained in the portion of an LDP PDU
Intialization Message.
3.5.4. The Label Distribution Protocol's Entity Statistics Table
The LDP Entity Statistics Table will maintain counters related to an
LDP Entity. This Table should be a read-only table which contains
statistical information.
Each row in this table will be related to a single LDP Entity.
3.5.5. The LDP Peer Table
The LDP Peer Table is a read-only table which contains information
about LDP Peers. Each row in this table represents an LDP Peer which
is known to an LDP Entity.
3.5.6. The LDP Session Table
The LDP Session Table is a read-only table. Each entry in this table
represents a single session between an LDP Entity and a Peer.
3.5.7. The LDP ATM Session Table
The MPLS LDP ATM Session Table is a read-only table which contains
session information specific to ATM.
3.5.8. The LDP Frame Relay Session Table
The MPLS LDP Frame Relay Session Table is a read-only table which
contains session information specific to Frame Relay.
3.5.9. The LDP Session Statistics Table
The MPLS LDP Session Stats Table is a read-only table which contains
statistical information on sessions.
Expires April 2000 [Page 7]
INTERNET-DRAFT MPLS LDP MIB October 1999
3.5.10. The LDP Session Peer Address Table
The MPLS LDP Session Peer Address Table is a table which 'extends'
the mplsLdpSessionTable. This table is a read-only table which
stores Addresses learned after session initialization via "Address
Message" advertisement.
3.5.11. The LDP Adjacencies Table
This is a table of all adjacencies between all LPD Entities and all
LDP Peers. A Session may have one or more adjacencies.
3.5.12. The LDP Label Information Base (LIB) Table
The MPLS LDP LIB Table is a read-only table which contains
information stored in the LIB. This table is indexed by a unique
number which could be used to represent the LSP segment related to
this LIB entry. The Lsp number corresponds to a FEC entry in the FEC
Table which is described next.
3.5.13. The LDP FEC Table
The FEC Table is a read-only table whic contains FEC (Forwarding
Equivalence Class) information. Each entry/row represents a single
FEC Element.
3.6. The LDP Notifications Group
3.6.1. LDP Notifications
Currently, there is one notification which will be sent when an LDP
attempts to initialize the same session beyond the configured
threshold.
4. MPLS Label Distribution Protocol MIB Definitions
MPLS-LDP-MIB DEFINITIONS ::= BEGIN
IMPORTS
OBJECT-TYPE, MODULE-IDENTITY, NOTIFICATION-TYPE,
experimental,
Integer32, Counter32, Unsigned32
FROM SNMPv2-SMI
Expires April 2000 [Page 8]
INTERNET-DRAFT MPLS LDP MIB October 1999
MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP
FROM SNMPv2-CONF
TEXTUAL-CONVENTION, RowStatus, TimeInterval
FROM SNMPv2-TC
InterfaceIndex
FROM IF-MIB
-- AtmInterfaceType,
AtmVcIdentifier, AtmVpIdentifier
FROM ATM-TC-MIB
AddressFamilyNumbers
FROM IANA-ADDRESS-FAMILY-NUMBERS-MIB
;
mplsLdpMIB MODULE-IDENTITY
LAST-UPDATED "9910071200Z" -- October 7, 1999
ORGANIZATION "Multiprotocol Label Switching (mpls) Working Group"
CONTACT-INFO
"Joan Cucchiara (joan@ironbridgenetworks.com)
IronBridge Networks
Hans Sjostrand (hans.sjostrand@etx.ericsson.se)
Ericsson
James V. Luciani (luciani@baynetworks.com)
Nortel Networks"
DESCRIPTION
"This MIB contains managed object definitions for the
Multiprotocol Label Switching, Label Distribution
Protocol, LDP, as defined in draft-ietf-mpls-ldp-06.txt."
::= { experimental XXXX } -- to be assigned
--********************************************************************
-- MPLS LDP Textual Conventions
--********************************************************************
--
MplsLsrIdentifier ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The Label Switch Router (LSR) identifier
is the first 4 bytes or the IP Address component
of the Label Distribution Protocol (LDP) identifier."
SYNTAX OCTET STRING (SIZE (4))
--
-- A similar TC is also used in RFC2677.txt, perhaps
-- this should be made general and not MPLS specific.
--
MplsLdpGenAddr ::= TEXTUAL-CONVENTION
Expires April 2000 [Page 9]
INTERNET-DRAFT MPLS LDP MIB October 1999
STATUS current
DESCRIPTION
"The value of an network layer or data link layer address."
SYNTAX OCTET STRING (SIZE (0..64))
MplsLdpIdentifier ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The LDP identifier is a six octet quantity
which is used to identify an Label Switch Router
(LSR) label space.
The first four octets encode an IP address
assigned to the LSR, and the last two octets
identify a specific label space within the LSR."
SYNTAX OCTET STRING (SIZE (6))
MplsLdpLabelTypes ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The Layer 2 label types which are defined for
MPLS LDP are generic(1), atm(2), or frameRelay(3)."
SYNTAX INTEGER(1..3)
-- Top-level structure of the MIB (the following is proposed)
mpls OBJECT IDENTIFIER ::= { mplsProtocols }
mplsProtocols OBJECT IDENTIFIER ::= { mplsLdpObjects }
-- under mplsProtocols will be LDP, CR-LDP,
-- and other MPLS "Protocols".
mplsLdpObjects OBJECT IDENTIFIER ::= { mplsLdpMIB 1 }
mplsLdpNotifications OBJECT IDENTIFIER ::= { mplsLdpMIB 2 }
mplsLdpConformance OBJECT IDENTIFIER ::= { mplsLdpMIB 3 }
--****************************************************************
-- MPLS LDP Objects
--****************************************************************
mplsLdpLsrObjects OBJECT IDENTIFIER ::= { mplsLdpObjects 1 }
mplsLdpEntityObjects OBJECT IDENTIFIER ::= { mplsLdpObjects 2 }
--
-- The MPLS Label Distribution Protocol Label Switch Router Objects
--
mplsLdpLsrId OBJECT-TYPE
Expires April 2000 [Page 10]
INTERNET-DRAFT MPLS LDP MIB October 1999
SYNTAX MplsLsrIdentifier
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The LSR's Identifier."
::= { mplsLdpLsrObjects 1 }
mplsLdpLsrLabelRetentionMode OBJECT-TYPE
SYNTAX INTEGER {
conservative(1),
liberal(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The LSR can be configured to use either
conservative or liberal label retention mode.
If the value of this object is conservative(1)
then advertized label mappings are retained
only if they will be used to forward packets,
i.e. if label came from a valid next hop.
If the value of this object is liberal(2)
then all advertized label mappings are retained
whether they are from a valid next hop or not."
::= { mplsLdpLsrObjects 2 }
--
-- The MPLS Label Distribution Protocol Entity Table
--
mplsLdpEntityTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsLdpEntityEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains information about the
MPLS Label Distribution Protocol Entities which
exist on this Label Switch Router (LSR)."
::= { mplsLdpEntityObjects 1 }
mplsLdpEntityEntry OBJECT-TYPE
SYNTAX MplsLdpEntityEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table represents an LDP entity.
An entry can be created by a network administrator
or by an SNMP agent as instructed by LDP."
Expires April 2000 [Page 11]
INTERNET-DRAFT MPLS LDP MIB October 1999
INDEX { mplsLdpEntityLdpId, mplsLdpEntityIndex }
::= { mplsLdpEntityTable 1 }
MplsLdpEntityEntry ::= SEQUENCE {
mplsLdpEntityLdpId MplsLdpIdentifier,
mplsLdpEntityIndex Unsigned32,
mplsLdpEntityWellKnownDiscoveryPort Unsigned32,
mplsLdpEntityMtu Integer32,
mplsLdpEntityKeepAliveHoldTimer Integer32,
mplsLdpEntityFailedInitSessionThreshold Integer32,
mplsLdpEntityLabelDistributionMethod INTEGER,
mplsLdpEntityOptionalParameters MplsLdpLabelTypes,
mplsLdpEntityRowStatus RowStatus
}
mplsLdpEntityLdpId OBJECT-TYPE
SYNTAX MplsLdpIdentifier
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The LDP identifier.
The first four octets encode an IP address
assigned to the LSR, and the last two octets
identify a specific label space within the
LSR."
REFERENCE
"LDP Specification, Section on LDP Identifiers."
::= { mplsLdpEntityEntry 1 }
mplsLdpEntityIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This index should be unique to differentiate
LDP Identifiers, such that this index along
with the LDP Identifier will uniquely identify
the row."
::= { mplsLdpEntityEntry 2 }
mplsLdpEntityWellKnownDiscoveryPort OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The well known LDP Discovery Port."
::= { mplsLdpEntityEntry 3 }
Expires April 2000 [Page 12]
INTERNET-DRAFT MPLS LDP MIB October 1999
mplsLdpEntityMtu OBJECT-TYPE
SYNTAX Integer32 (0..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum transmission unit (MTU) that was configured
for this entity."
::= { mplsLdpEntityEntry 4 }
mplsLdpEntityKeepAliveHoldTimer OBJECT-TYPE
SYNTAX Integer32 (1..65535)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The two octet value which is the proposed keep alive hold
timer for this LDP Entity."
::= { mplsLdpEntityEntry 5 }
mplsLdpEntityFailedInitSessionThreshold OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"When attempting to establish a session with a
given Peer, the given LDP Entity should
send out a notification when exceeding this threshold.
A value of 0 (zero) for this object
indicates that the threshold is infinity.
In other words, a notification will not
be sent if the value of this object is 0 (zero)."
::= { mplsLdpEntityEntry 6 }
mplsLdpEntityLabelDistributionMethod OBJECT-TYPE
SYNTAX INTEGER {
downstreamOnDemand(1),
downstreamUnsolicited(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"For any given LDP session, the method of
label distribution must be specified."
::= { mplsLdpEntityEntry 7 }
mplsLdpEntityOptionalParameters OBJECT-TYPE
SYNTAX MplsLdpLabelTypes
MAX-ACCESS read-create
Expires April 2000 [Page 13]
INTERNET-DRAFT MPLS LDP MIB October 1999
STATUS current
DESCRIPTION
"Specifies the optional parameters for the LDP
Initialization Message. If the value is generic(1)
then no optional parameters will be sent in
the LDP Initialization message associated with
this Entity.
If the value is atmParameters(2) then
a row must be created in the mplsLdpEntityAtmParms
Table, which corresponds to this entry.
If the value is frameRelayParameters(3) then
a row must be created in the mplsLdpEntityFrameRelayParms
Table, which corresponds to this entry."
::= { mplsLdpEntityEntry 8 }
mplsLdpEntityRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An object that allows entries in this table to
be created and deleted using the
RowStatus convention."
::= { mplsLdpEntityEntry 9 }
--
-- Ldp Entity Objects for ATM
--
mplsLdpEntityAtmObjects OBJECT IDENTIFIER ::= { mplsLdpEntityObjects 2 }
mplsLdpEntityAtmParmsTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsLdpEntityAtmParmsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains information about the
ATM specific information which could be used
in the 'Optional Parameters'."
::= { mplsLdpEntityAtmObjects 1 }
mplsLdpEntityAtmParmsEntry OBJECT-TYPE
SYNTAX MplsLdpEntityAtmParmsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table represents the ATM parameters
Expires April 2000 [Page 14]
INTERNET-DRAFT MPLS LDP MIB October 1999
for this LDP entity."
INDEX { mplsLdpEntityLdpId, mplsLdpEntityIndex }
::= { mplsLdpEntityAtmParmsTable 1 }
MplsLdpEntityAtmParmsEntry ::= SEQUENCE {
mplsLdpEntityAtmMergeCap INTEGER,
mplsLdpEntityAtmLabelRangeComponents Unsigned32,
mplsLdpEntityAtmVcDirectionality INTEGER,
mplsLdpEntityAtmRowStatus RowStatus
}
mplsLdpEntityAtmMergeCap OBJECT-TYPE
SYNTAX INTEGER {
notSupported(0),
vpMerge(1),
vcMerge(2),
vpAndVcMerge(3)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Denotes the Merge Capability of this Entity."
::= { mplsLdpEntityAtmParmsEntry 1 }
mplsLdpEntityAtmLabelRangeComponents OBJECT-TYPE
SYNTAX Unsigned32 (1..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Number of LabelRange Components in the Initialization
message. This also represents the number of entries
in the mplsLdpLabelRangeComponentsTable which correspond
to this entry."
::= { mplsLdpEntityAtmParmsEntry 2 }
mplsLdpEntityAtmVcDirectionality OBJECT-TYPE
SYNTAX INTEGER {
bidirectional(0),
unidirectional(1)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"If the value of this object is 'bidirectional(0)',
a given VCI, within a given VPI, is used as a
label for both directions independently.
If the value of this object is 'unidirectional(1)',
Expires April 2000 [Page 15]
INTERNET-DRAFT MPLS LDP MIB October 1999
a given VCI within a VPI designates one direction."
::= { mplsLdpEntityAtmParmsEntry 3 }
mplsLdpEntityAtmRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An object that allows entries in this table to
be created and deleted using the
RowStatus convention."
::= { mplsLdpEntityAtmParmsEntry 4 }
--
-- The MPLS LDP Entity Configurable ATM Label Range Table
--
mplsLdpEntityConfAtmLabelRangeTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsLdpEntityConfAtmLabelRangeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The MPLS LDP Entity Configurable ATM Label Range Table.
The purpose of this table is to provide a mechanism
for specifying a contiguous range of vpi's
with a contiguous range of vci's, or a 'label range'
for LDP Entities.
LDP Entities which use ATM must have at least one
entry in this table."
::= { mplsLdpEntityAtmObjects 2 }
mplsLdpEntityConfAtmLabelRangeEntry OBJECT-TYPE
SYNTAX MplsLdpEntityConfAtmLabelRangeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A row in the LDP Entity Configurable ATM Label
Range Table. One entry in this table contains
information on a single range of labels
represented by the configured Upper and Lower
Bounds VPI/VCI pairs. These are the same
data used in the Initialization Message.
NOTE: The ranges for a specific LDP Entity
are UNIQUE and non-overlapping. For example,
for a specific LDP Entity index, there could
be one entry having ConfLowerBound vpi/vci == 0/32, and
ConfUpperBound vpi/vci == 0/100, and a second entry for this
same interface with ConfLowerBound vpi/vci == 0/101 and
Expires April 2000 [Page 16]
INTERNET-DRAFT MPLS LDP MIB October 1999
ConfUpperBound vpi/vci == 0/200. However, there could not be
a third entry with ConfLowerBound vpi/vci == 0/200 and
ConfUpperBound vpi/vci == 0/300 because this label range overlaps
with the second entry (i.e. both entries now have 0/200).
A row will not be created unless a unique and non-overlapping
range is specified. Thus, row creation implies a one-shot
row creation of LDP EntityID and ConfLowerBound vpi/vci and
ConfUpperBound vpi/vci. At least one label range entry
for a specific LDP Entity MUST include the default VPI/VCI
values denoted in the LDP Entity Table."
INDEX { mplsLdpEntityLdpId,
mplsLdpEntityIndex }
::= { mplsLdpEntityConfAtmLabelRangeTable 1 }
MplsLdpEntityConfAtmLabelRangeEntry ::= SEQUENCE {
mplsLdpEntityConfAtmLabelRangeMinimumVpi AtmVpIdentifier,
mplsLdpEntityConfAtmLabelRangeMinimumVci AtmVcIdentifier,
mplsLdpEntityConfAtmLabelRangeMaximumVpi AtmVpIdentifier,
mplsLdpEntityConfAtmLabelRangeMaximumVci AtmVcIdentifier,
mplsLdpEntityConfAtmLabelRangeRowStatus RowStatus
}
mplsLdpEntityConfAtmLabelRangeMinimumVpi OBJECT-TYPE
SYNTAX AtmVpIdentifier
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The minimum VPI number configured for this range."
::= { mplsLdpEntityConfAtmLabelRangeEntry 1 }
mplsLdpEntityConfAtmLabelRangeMinimumVci OBJECT-TYPE
SYNTAX AtmVcIdentifier
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The minimum VCI number configured for this range."
::= { mplsLdpEntityConfAtmLabelRangeEntry 2 }
mplsLdpEntityConfAtmLabelRangeMaximumVpi OBJECT-TYPE
SYNTAX AtmVpIdentifier
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum VPI number configured for this range."
::= { mplsLdpEntityConfAtmLabelRangeEntry 3 }
mplsLdpEntityConfAtmLabelRangeMaximumVci OBJECT-TYPE
SYNTAX AtmVcIdentifier
MAX-ACCESS read-create
Expires April 2000 [Page 17]
INTERNET-DRAFT MPLS LDP MIB October 1999
STATUS current
DESCRIPTION
"The maximum VCI number configured for this range."
::= { mplsLdpEntityConfAtmLabelRangeEntry 4 }
mplsLdpEntityConfAtmLabelRangeRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An object that allows entries in this
table to be created and deleted using
the RowStatus convention.
There must exist at least one entry in this
table for every LDP Entity that has
'mplsLdpEntityOptionalParameters' object with
a value of 'atmSessionParameters'."
::= { mplsLdpEntityConfAtmLabelRangeEntry 5 }
--
-- Ldp Entity Objects for Frame Relay
--
mplsLdpEntityFrameRelayObjects OBJECT IDENTIFIER ::=
{ mplsLdpEntityObjects 3 }
mplsLdpEntityFrameRelayParmsTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsLdpEntityFrameRelayParmsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains information about the
Optional Parameters to specify what this Entity is
going to specify for Frame Relay specific
LDP Intialization Messages."
::= { mplsLdpEntityFrameRelayObjects 1 }
mplsLdpEntityFrameRelayParmsEntry OBJECT-TYPE
SYNTAX MplsLdpEntityFrameRelayParmsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table represents the Frame Relay
optional parameters associated with the LDP entity."
INDEX { mplsLdpEntityLdpId, mplsLdpEntityIndex }
::= { mplsLdpEntityFrameRelayParmsTable 1 }
MplsLdpEntityFrameRelayParmsEntry ::= SEQUENCE {
Expires April 2000 [Page 18]
INTERNET-DRAFT MPLS LDP MIB October 1999
mplsLdpEntityFrMergeCap INTEGER,
mplsLdpEntityFrLabelRangeComponents Unsigned32,
mplsLdpEntityFrVcDirectionality INTEGER,
mplsLdpEntityFrParmsRowStatus RowStatus
}
mplsLdpEntityFrMergeCap OBJECT-TYPE
SYNTAX INTEGER {
notSupported(0),
supported(1)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This represents whether or not Frame Relay merge capability
is supported."
::= { mplsLdpEntityFrameRelayParmsEntry 1 }
mplsLdpEntityFrLabelRangeComponents OBJECT-TYPE
SYNTAX Unsigned32 (1..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Number of LabelRange Components in the Initialization
message. This also represents the number of entries
in the mplsLdpEntityConfFRLabelRangeTable which correspond
to this entry."
::= { mplsLdpEntityFrameRelayParmsEntry 2 }
mplsLdpEntityFrVcDirectionality OBJECT-TYPE
SYNTAX INTEGER {
bidirectional(0),
unidirection(1)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"If the value of this object is 'bidirectional(0)', then
the LSR supports the use of a given DLCI as a label for
both directions independently. If the value of this object
is 'unidirectional(1)', then the LSR uses the given DLCI
as a label in only one direction."
::= { mplsLdpEntityFrameRelayParmsEntry 3 }
mplsLdpEntityFrParmsRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An object that allows entries in this table to
Expires April 2000 [Page 19]
INTERNET-DRAFT MPLS LDP MIB October 1999
be created and deleted using the
RowStatus convention."
::= { mplsLdpEntityFrameRelayParmsEntry 4 }
--
-- Frame Relay Label Range Components
--
mplsLdpEntityConfFrLabelRangeTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsLdpEntityConfFrLabelRangeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains information about the
Optional Parameters to specify what this Entity is
going to specify for Frame Relay specific
LDP Intialization Messages."
::= { mplsLdpEntityFrameRelayObjects 2 }
mplsLdpEntityConfFrLabelRangeEntry OBJECT-TYPE
SYNTAX MplsLdpEntityConfFrLabelRangeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table represents the Frame Relay
optional parameters associated with the LDP entity."
INDEX { mplsLdpEntityLdpId, mplsLdpEntityIndex }
::= { mplsLdpEntityConfFrLabelRangeTable 1 }
MplsLdpEntityConfFrLabelRangeEntry ::= SEQUENCE {
mplsLdpConfFrLen INTEGER,
mplsLdpConfFrMinimumDlci Integer32,
mplsLdpConfFrMaximumDlci Integer32,
mplsLdpConfFrRowStatus RowStatus
}
mplsLdpConfFrLen OBJECT-TYPE
SYNTAX INTEGER {
tenDlciBits(0),
seventeenDlciBits(1),
twentyThreeDlciBits(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the DLCI bits."
::= { mplsLdpEntityConfFrLabelRangeEntry 1 }
mplsLdpConfFrMinimumDlci OBJECT-TYPE
Expires April 2000 [Page 20]
INTERNET-DRAFT MPLS LDP MIB October 1999
SYNTAX Integer32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The lower bound which is supported. This value should
be the same as that in the Frame Relay Label Range Component's
Minimum DLCI field."
::= { mplsLdpEntityConfFrLabelRangeEntry 2 }
mplsLdpConfFrMaximumDlci OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The upper bound which is supported. This value should
be the same as that in the Frame Relay Label Range Component's
Maximum DLCI field."
::= { mplsLdpEntityConfFrLabelRangeEntry 3 }
mplsLdpConfFrRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An object that allows entries in this table to
be created and deleted using the
RowStatus convention.
If the value of the object 'mplsLdpEntityOptionalParameters'
contains the value of 'frameReleaySessionParameters(3)' then
there must be at least one corresponding entry in this table."
::= { mplsLdpEntityConfFrLabelRangeEntry 4 }
--
-- The MPLS LDP Entity Statistics Table
--
mplsLdpEntityStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsLdpEntityStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table is a read-only table which augments
the mplsLdpEntityTable. The purpose of this
table is to keep statistical information about
the LDP Entities on the LSR."
::= { mplsLdpEntityObjects 4 }
mplsLdpEntityStatsEntry OBJECT-TYPE
SYNTAX MplsLdpEntityStatsEntry
Expires April 2000 [Page 21]
INTERNET-DRAFT MPLS LDP MIB October 1999
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A row in this table contains statistical information
about an LDP Entity. Some counters contained in a
row are for fatal errors received during a former
LDP Session associated with this entry. For example,
an Ldp Pdu received on a TCP connection for an
LDP Session which contains a fatal error is counted
here, because the session is terminated.
If the error is NOT fatal (i.e. and the Session
remains), then the error is counted in the
mplsLdpSessionStatsEntry."
AUGMENTS { mplsLdpEntityEntry }
::= { mplsLdpEntityStatsTable 1 }
MplsLdpEntityStatsEntry ::= SEQUENCE {
mplsLdpAttemptedSessions Counter32,
mplsLdpSessionRejectedNoHelloErrors Counter32,
mplsLdpSessionRejectedAdvertisementErrors Counter32,
mplsLdpSessionRejectedMaxPduErrors Counter32,
mplsLdpSessionRejectedLabelRangeErrors Counter32,
mplsLdpBadLdpIdentifierErrors Counter32,
mplsLdpBadPduLengthErrors Counter32,
mplsLdpBadMessageLengthErrors Counter32,
mplsLdpBadTlvLengthErrors Counter32,
mplsLdpMalformedTlvValueErrors Counter32,
mplsLdpKeepAliveTimerExpiredErrors Counter32,
mplsLdpShutdownNotifReceived Counter32,
mplsLdpShutdownNotifSent Counter32
}
mplsLdpAttemptedSessions OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A count of the total attempted sessions for
this LDP Entity."
::= { mplsLdpEntityStatsEntry 1 }
mplsLdpSessionRejectedNoHelloErrors OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A count of the Session Rejected/No Hello Error
Notification Messages sent or received by
this LDP Entity."
Expires April 2000 [Page 22]
INTERNET-DRAFT MPLS LDP MIB October 1999
::= { mplsLdpEntityStatsEntry 2 }
mplsLdpSessionRejectedAdvertisementErrors OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A count of the Session Rejected/Parameters
Advertisement Mode Error Notification Messages sent
or received by this LDP Entity."
::= { mplsLdpEntityStatsEntry 3 }
mplsLdpSessionRejectedMaxPduErrors OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A count of the Session Rejected/Parameters
Max Pdu Length Error Notification Messages sent
or received by this LDP Entity."
::= { mplsLdpEntityStatsEntry 4 }
mplsLdpSessionRejectedLabelRangeErrors OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A count of the Session Rejected/Parameters
Label Range Notification Notification Messages sent
or received by this LDP Entity."
::= { mplsLdpEntityStatsEntry 5 }
mplsLdpBadLdpIdentifierErrors OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of Bad LDP Identifier Fatal
Errors detected by the session(s) (past and present) associated
with this LDP Entity."
REFERENCE
"LDP Specification, Section 3.5.1.2."
::= { mplsLdpEntityStatsEntry 6 }
mplsLdpBadPduLengthErrors OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
Expires April 2000 [Page 23]
INTERNET-DRAFT MPLS LDP MIB October 1999
DESCRIPTION
"This object counts the number of Bad Pdu Length Fatal
Errors detected by the session(s) (past and present) associated
with this LDP Entity."
REFERENCE
"LDP Specification, Section 3.5.1.2."
::= { mplsLdpEntityStatsEntry 7 }
mplsLdpBadMessageLengthErrors OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of Bad Message Length Fatal
Errors detected by the session(s) (past and present) associated
with this LDP Entity."
REFERENCE
"LDP Specification, Section 3.5.1.2."
::= { mplsLdpEntityStatsEntry 8 }
mplsLdpBadTlvLengthErrors OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of Bad TLV Length Fatal
Errors detected by the session(s) (past and present) associated
with this LDP Entity."
REFERENCE
"LDP Specification, Section 3.5.1.2."
::= { mplsLdpEntityStatsEntry 9 }
mplsLdpMalformedTlvValueErrors OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of Malformed TLV Value Fatal
Errors detected by the session(s) (past and present) associated
with this LDP Entity."
REFERENCE
"LDP Specification, Section 3.5.1.2."
::= { mplsLdpEntityStatsEntry 10 }
mplsLdpKeepAliveTimerExpiredErrors OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of Session Keep Alive Timer
Expires April 2000 [Page 24]
INTERNET-DRAFT MPLS LDP MIB October 1999
Expired Errors detected by the session(s) (past and present)
associated with this LDP Entity."
REFERENCE
"LDP Specification, Section 3.5.1.2."
::= { mplsLdpEntityStatsEntry 11 }
mplsLdpShutdownNotifReceived OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of Shutdown Notfications
received related to session(s) (past and present) associated
with this LDP Entity."
::= { mplsLdpEntityStatsEntry 12 }
mplsLdpShutdownNotifSent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of Shutdown Notfications
sent related to session(s) (past and present) associated
with this LDP Entity."
::= { mplsLdpEntityStatsEntry 13 }
--
-- The MPLS LDP Peer Table
--
mplsLdpPeerObjects OBJECT IDENTIFIER ::= { mplsLdpObjects 3 }
mplsLdpPeerTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsLdpPeerEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information about LDP peers which have been discovered
by the LDP Entities that are managed by this agent."
::= { mplsLdpPeerObjects 1 }
mplsLdpPeerEntry OBJECT-TYPE
SYNTAX MplsLdpPeerEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information about a single Peer."
INDEX { mplsLdpPeerLdpId,
mplsLdpPeerIndex }
Expires April 2000 [Page 25]
INTERNET-DRAFT MPLS LDP MIB October 1999
::= { mplsLdpPeerTable 1 }
MplsLdpPeerEntry ::= SEQUENCE {
mplsLdpPeerLdpId MplsLdpIdentifier,
mplsLdpPeerIndex Unsigned32,
mplsLdpPeerInternetworkAddrType AddressFamilyNumbers,
mplsLdpPeerInternetworkAddr MplsLdpGenAddr,
mplsLdpPeerLabelDistributionMethod INTEGER,
mplsLdpPeerLoopDetectionForPV INTEGER,
mplsLdpPeerPathVectorLimit Integer32
}
mplsLdpPeerLdpId OBJECT-TYPE
SYNTAX MplsLdpIdentifier
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The LDP identifier of this LDP Peer."
::= { mplsLdpPeerEntry 1 }
mplsLdpPeerIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An identifier for the LDP peer that is unique within the
scope of this agent."
::= { mplsLdpPeerEntry 2 }
mplsLdpPeerInternetworkAddrType OBJECT-TYPE
SYNTAX AddressFamilyNumbers
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The type of the internetwork layer address of this
LDP peer. This object indicates how the value of
mplsLdpPeerInternetworkAddr is to be interpreted."
::= { mplsLdpPeerEntry 3 }
mplsLdpPeerInternetworkAddr OBJECT-TYPE
SYNTAX MplsLdpGenAddr
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of the internetwork layer address of this LDP peer."
::= { mplsLdpPeerEntry 4 }
mplsLdpPeerLabelDistributionMethod OBJECT-TYPE
SYNTAX INTEGER {
downstreamOnDemand(1),
Expires April 2000 [Page 26]
INTERNET-DRAFT MPLS LDP MIB October 1999
downstreamUnsolicited(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"For any given LDP session, the method of
label distribution must be specified."
REFERENCE
"draft-ietf-mpls-arch-06.txt [20]."
::= { mplsLdpPeerEntry 5 }
mplsLdpPeerLoopDetectionForPV OBJECT-TYPE
SYNTAX INTEGER {
disabled(0),
enabled(1)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An indication of whether loop detection based on path vectors is
disabled or enabled for this Peer.
If this object has a value of disabled(0),
then loop detection is disabled. Otherwise, if this object has
a value of enabled(1), then loop detection based on path vectors
is enabled."
::= { mplsLdpPeerEntry 6 }
mplsLdpPeerPathVectorLimit OBJECT-TYPE
SYNTAX Integer32 (0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If the value of 'mplsLdpPeerLoopDetectionForPV' for this entry is
'enabled(1)', the this object represents that Path Vector Limit
for this peer.
If the value of 'mplsLdpPeerLoopDetectionForPV' for this entry
is 'disabled(0)', then this value should be 0 (zero)."
::= { mplsLdpPeerEntry 7 }
--
-- The MPLS LDP Sessions Table
--
mplsLdpSessionObjects OBJECT IDENTIFIER ::= { mplsLdpObjects 4 }
mplsLdpSessionTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsLdpSessionEntry
Expires April 2000 [Page 27]
INTERNET-DRAFT MPLS LDP MIB October 1999
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of Sessions between the LDP Entities and
LDP Peers. Each row represents a single session."
::= { mplsLdpSessionObjects 1 }
mplsLdpSessionEntry OBJECT-TYPE
SYNTAX MplsLdpSessionEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table represents information on a
single session between an LDP Entity and LDP Peer.
The information contained in a row is read-only."
INDEX { mplsLdpEntityLdpId,
mplsLdpEntityIndex,
mplsLdpPeerLdpId,
mplsLdpPeerIndex,
mplsLdpSessionIndex
}
::= { mplsLdpSessionTable 1 }
MplsLdpSessionEntry ::= SEQUENCE {
mplsLdpSessionIndex Unsigned32,
mplsLdpSessionState INTEGER,
mplsLdpSessionProtocolVersion Integer32,
mplsLdpSessionKeepAliveHoldTimeRemaining TimeInterval,
mplsLdpSessionLabelAdvertisement INTEGER,
mplsLdpSessionLoopDetectionForPV INTEGER,
mplsLdpSessionPathVectorLimit Integer32,
mplsLdpSessionMaxPduLength Integer32
}
mplsLdpSessionIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An unique identifier for this entry such that it
identifies a specific LDP Session."
::= { mplsLdpSessionEntry 1 }
mplsLdpSessionState OBJECT-TYPE
SYNTAX INTEGER {
nonexistent(1),
initialized(2),
openrec(3),
opensent(4),
operational(5)
Expires April 2000 [Page 28]
INTERNET-DRAFT MPLS LDP MIB October 1999
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current state of the session, all of the
states 1 - 5 are based on the state machine for
session negotiation behavior."
::= { mplsLdpSessionEntry 2 }
mplsLdpSessionProtocolVersion OBJECT-TYPE
SYNTAX Integer32(1..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The version of the LDP Protocol which
this session is using."
::= { mplsLdpSessionEntry 3 }
mplsLdpSessionKeepAliveHoldTimeRemaining OBJECT-TYPE
SYNTAX TimeInterval
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The keep alive hold time remaining for this session."
::= { mplsLdpSessionEntry 4 }
mplsLdpSessionLabelAdvertisement OBJECT-TYPE
SYNTAX INTEGER {
downStreamUnsolicited(0),
downStreamOnDemand(1)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The label advertisement discipline used for this Session."
::= { mplsLdpSessionEntry 5 }
mplsLdpSessionLoopDetectionForPV OBJECT-TYPE
SYNTAX INTEGER {
disabled(0),
enabled(1)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An indication of whether loop detection based on path vectors is
disabled or enabled for this session.
If this object has a value of disabled(0),
Expires April 2000 [Page 29]
INTERNET-DRAFT MPLS LDP MIB October 1999
then loop detection is disabled. Otherwise, if this object has
a value of enabled(1), then loop detection based on path vectors
is enabled."
::= { mplsLdpSessionEntry 6 }
mplsLdpSessionPathVectorLimit OBJECT-TYPE
SYNTAX Integer32 (0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If the value of 'mplsLdpSessionLoopDetectionForPV' for this entry is
'enabled(1)', the this object represents the Path Vector Limit
for this session.
If the value of 'mplsLdpSessionLoopDetectionForPV' for this entry
is 'disabled(0)', then this value should be 0 (zero)."
::= { mplsLdpSessionEntry 7 }
mplsLdpSessionMaxPduLength OBJECT-TYPE
SYNTAX Integer32 (0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of maximum allowable length for LDP PDUs for
this session. This value may have been negotiated during
the Session Initialization."
::= { mplsLdpSessionEntry 8 }
--
-- MPLS LDP ATM Session Information
--
mplsLdpAtmSessionTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsLdpAtmSessionEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of Sessions between the LDP Entities and
LDP Peers using ATM as the underlying media.
Each row represents a single session.
NOTE: this table cannot use the 'AUGMENTS'
clause because there is not necessarily a one-to-one
mapping between this table and the mplsLdpSessionTable."
::= { mplsLdpSessionObjects 2 }
mplsLdpAtmSessionEntry OBJECT-TYPE
Expires April 2000 [Page 30]
INTERNET-DRAFT MPLS LDP MIB October 1999
SYNTAX MplsLdpAtmSessionEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table represents information on a
single session between an LDP Entity and LDP Peer.
The information contained in a row is read-only."
INDEX { mplsLdpEntityLdpId,
mplsLdpEntityIndex,
mplsLdpPeerLdpId,
mplsLdpPeerIndex,
mplsLdpSessionIndex
}
::= { mplsLdpAtmSessionTable 1 }
MplsLdpAtmSessionEntry ::= SEQUENCE {
mplsLdpSessionAtmLabelRangeLowerBoundVpi AtmVpIdentifier,
mplsLdpSessionAtmLabelRangeLowerBoundVci AtmVcIdentifier,
mplsLdpSessionAtmLabelRangeUpperBoundVpi AtmVpIdentifier,
mplsLdpSessionAtmLabelRangeUpperBoundVci AtmVcIdentifier
}
mplsLdpSessionAtmLabelRangeLowerBoundVpi OBJECT-TYPE
SYNTAX AtmVpIdentifier
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The minimum VPI number for this range."
::= { mplsLdpAtmSessionEntry 1 }
mplsLdpSessionAtmLabelRangeLowerBoundVci OBJECT-TYPE
SYNTAX AtmVcIdentifier
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The minimum VCI number for this range."
::= { mplsLdpAtmSessionEntry 2 }
mplsLdpSessionAtmLabelRangeUpperBoundVpi OBJECT-TYPE
SYNTAX AtmVpIdentifier
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum VPI number for this range."
::= { mplsLdpAtmSessionEntry 3 }
mplsLdpSessionAtmLabelRangeUpperBoundVci OBJECT-TYPE
SYNTAX AtmVcIdentifier
MAX-ACCESS read-only
STATUS current
Expires April 2000 [Page 31]
INTERNET-DRAFT MPLS LDP MIB October 1999
DESCRIPTION
"The maximum VCI number for this range."
::= { mplsLdpAtmSessionEntry 4 }
--
-- MPLS LDP Frame Relay Session Information
--
mplsLdpFrameRelaySessionTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsLdpFrameRelaySessionEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of Sessions between the LDP Entities and
LDP Peers using Frame Relay as the underlying media.
Each row represents a single session.
NOTE: this table cannot use the 'AUGMENTS'
clause because there is not necessarily a one-to-one
mapping between this table and the mplsLdpSessionTable."
::= { mplsLdpSessionObjects 3 }
mplsLdpFrameRelaySessionEntry OBJECT-TYPE
SYNTAX MplsLdpFrameRelaySessionEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table represents information on a
single session between an LDP Entity and LDP Peer.
The information contained in a row is read-only."
INDEX { mplsLdpEntityLdpId,
mplsLdpEntityIndex,
mplsLdpPeerLdpId,
mplsLdpPeerIndex,
mplsLdpSessionIndex
}
::= { mplsLdpFrameRelaySessionTable 1 }
MplsLdpFrameRelaySessionEntry ::= SEQUENCE {
mplsLdpFrSessionLen INTEGER,
mplsLdpFrSessionMinDlci Integer32,
mplsLdpFrSessionMaxDlci Integer32
}
mplsLdpFrSessionLen OBJECT-TYPE
SYNTAX INTEGER {
tenDlciBits(0),
seventeenDlciBits(1),
twentyThreeDlciBits(2)
Expires April 2000 [Page 32]
INTERNET-DRAFT MPLS LDP MIB October 1999
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the DLCI bits."
::= { mplsLdpFrameRelaySessionEntry 1 }
mplsLdpFrSessionMinDlci OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The lower bound of DLCIs which are supported."
::= { mplsLdpFrameRelaySessionEntry 2 }
mplsLdpFrSessionMaxDlci OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The upper bound of DLCIs which are supported."
::= { mplsLdpFrameRelaySessionEntry 3 }
--
-- The MPLS LDP Session Statistics Table
--
mplsLdpSessionStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsLdpSessionStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of Sessions between the LDP Entities and
LDP Peers."
::= { mplsLdpSessionObjects 4 }
mplsLdpSessionStatsEntry OBJECT-TYPE
SYNTAX MplsLdpSessionStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table represents statistical information on a
single session between an LDP Entity and LDP Peer."
AUGMENTS { mplsLdpSessionEntry }
::= { mplsLdpSessionStatsTable 1 }
MplsLdpSessionStatsEntry ::= SEQUENCE {
mplsLdpSessionStatsUnknownMessageTypeErrors Counter32,
mplsLdpSessionStatsUnknownTlvErrors Counter32
Expires April 2000 [Page 33]
INTERNET-DRAFT MPLS LDP MIB October 1999
}
mplsLdpSessionStatsUnknownMessageTypeErrors OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of Unknown Message Type
Errors detected during this session."
::= { mplsLdpSessionStatsEntry 1 }
mplsLdpSessionStatsUnknownTlvErrors OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of Unknown TLV Errors
detected during this session."
::= { mplsLdpSessionStatsEntry 2 }
--
-- Address Message/Address Withdraw Message Information
--
-- This information is associated with a specific Session
-- because Label Address Messages are sent after session
-- initialization has taken place.
--
mplsLdpSessionPeerAddressTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsLdpSessionPeerAddressEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table 'extends' the mplsLdpSessionTable.
This table is used to store Label Address Information
from Label Address Message received by this LSR from
Peers. This table is read-only and should be updated
when Label Withdraw Address Messages are received, i.e.
Rows should be deleted as apropriate.
NOTE: since more than one address may be contained
in a Label Address Message, this table 'extends',
rather than 'AUGMENTS' the mplsLdpSessionTable's
information."
::= { mplsLdpSessionObjects 5 }
mplsLdpSessionPeerAddressEntry OBJECT-TYPE
SYNTAX MplsLdpSessionPeerAddressEntry
MAX-ACCESS not-accessible
Expires April 2000 [Page 34]
INTERNET-DRAFT MPLS LDP MIB October 1999
STATUS current
DESCRIPTION
"An entry in this table represents information on
session's for a single next hop address which was
advertised in an Address Message from the LDP peer.
The information contained in a row is read-only."
INDEX { mplsLdpEntityLdpId,
mplsLdpEntityIndex,
mplsLdpPeerLdpId,
mplsLdpPeerIndex,
mplsLdpSessionIndex
}
::= { mplsLdpSessionPeerAddressTable 1 }
MplsLdpSessionPeerAddressEntry ::= SEQUENCE {
mplsLdpSessionPeerNextHopAddressType AddressFamilyNumbers,
mplsLdpSessionPeerNextHopAddress MplsLdpGenAddr
}
mplsLdpSessionPeerNextHopAddressType OBJECT-TYPE
SYNTAX AddressFamilyNumbers
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The internetwork layer address type of this Next Hop
Address as specified in the Label Address Message associated
with this Session. The value of this object indicates
how to interpret the value of mplsLdpSessionPeerNextHopAddress."
::= { mplsLdpSessionPeerAddressEntry 1 }
mplsLdpSessionPeerNextHopAddress OBJECT-TYPE
SYNTAX MplsLdpGenAddr
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of the next hop address."
REFERENCE
"LDP Specification [18] defines only IPv4 for LDP Protocol
Version 1, see section 3.4.3."
::= { mplsLdpSessionPeerAddressEntry 2 }
--
-- The MPLS LDP Hello Adjacency Table
--
mplsLdpHelloAdjacencyObjects OBJECT IDENTIFIER ::= { mplsLdpObjects 5 }
mplsLdpHelloAdjacencyTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsLdpHelloAdjacencyEntry
MAX-ACCESS not-accessible
Expires April 2000 [Page 35]
INTERNET-DRAFT MPLS LDP MIB October 1999
STATUS current
DESCRIPTION
"A table of Hello Adjacencies for Sessions."
::= { mplsLdpHelloAdjacencyObjects 1 }
mplsLdpHelloAdjacencyEntry OBJECT-TYPE
SYNTAX MplsLdpHelloAdjacencyEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each row represents a single LDP Hello Adjacency.
An LDP Session can have one or more Hello adjacencies."
INDEX { mplsLdpEntityLdpId,
mplsLdpEntityIndex,
mplsLdpPeerLdpId,
mplsLdpPeerIndex,
mplsLdpHelloAdjacencyIndex }
::= { mplsLdpHelloAdjacencyTable 1 }
MplsLdpHelloAdjacencyEntry ::= SEQUENCE {
mplsLdpHelloAdjacencyIndex Unsigned32,
mplsLdpHelloAdjacencyHoldTimeRemaining TimeInterval,
mplsLdpHelloAdjacencyType INTEGER
}
mplsLdpHelloAdjacencyIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An identifier for this specific adjacency."
::= { mplsLdpHelloAdjacencyEntry 1 }
mplsLdpHelloAdjacencyHoldTimeRemaining OBJECT-TYPE
SYNTAX TimeInterval
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time remaining for this Hello Adjacency.
This interval will change when the 'next'
Hello message which corresponds to this
Hello Adjacency is received."
::= { mplsLdpHelloAdjacencyEntry 2 }
mplsLdpHelloAdjacencyType OBJECT-TYPE
SYNTAX INTEGER {
link(1),
targeted(2)
}
MAX-ACCESS read-only
Expires April 2000 [Page 36]
INTERNET-DRAFT MPLS LDP MIB October 1999
STATUS current
DESCRIPTION
"This adjacency is the result of a 'link'
hello if the value of this object is link(1).
Otherwise, it is a result of a 'targeted'
hello, targeted(2)."
::= { mplsLdpHelloAdjacencyEntry 3 }
--
-- MPLS LDP LIB Table
--
mplsLdpLibObjects OBJECT IDENTIFIER ::= { mplsLdpObjects 6 }
mplsLdpLibTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsLdpLibEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table represents LIB (Label Information Base)
Information. The table is read-only."
::= { mplsLdpLibObjects 1 }
mplsLdpLibEntry OBJECT-TYPE
SYNTAX MplsLdpLibEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each row represents a single LDP LIB entry."
INDEX { mplsLdpLibLspId }
::= { mplsLdpLibTable 1 }
MplsLdpLibEntry ::= SEQUENCE {
mplsLdpLibLspId Unsigned32,
mplsLdpLibLabelInIfIndex InterfaceIndex,
mplsLdpLibLabelOutIfIndex InterfaceIndex,
mplsLdpLibLabelType MplsLdpLabelTypes,
mplsLdpLibInLabel MplsLdpGenAddr,
mplsLdpLibOutLabel MplsLdpGenAddr
}
mplsLdpLibLspId OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This number is used to uniquely identify this row, since this
row is associated with a specific LSP, it may also be used
to describe a unique number for an LSP. This number is used
in the mplsLdpFecTable to identify which FECs or FEC is
Expires April 2000 [Page 37]
INTERNET-DRAFT MPLS LDP MIB October 1999
associated with this LIB entry."
::= { mplsLdpLibEntry 1 }
mplsLdpLibLabelInIfIndex OBJECT-TYPE
SYNTAX InterfaceIndex
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ifIndex of the 'mplsLdpInLabel'."
::= { mplsLdpLibEntry 2 }
mplsLdpLibLabelOutIfIndex OBJECT-TYPE
SYNTAX InterfaceIndex
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ifIndex of the 'mplsLdpOutLabel'."
::= { mplsLdpLibEntry 3 }
mplsLdpLibLabelType OBJECT-TYPE
SYNTAX MplsLdpLabelTypes
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Layer 2 Label Type for 'mplsLdpInLabel' and
'mplsLdpOutLabel'."
::= { mplsLdpLibEntry 4 }
mplsLdpLibInLabel OBJECT-TYPE
SYNTAX MplsLdpGenAddr
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The incoming label of this LSP."
::= { mplsLdpLibEntry 5 }
mplsLdpLibOutLabel OBJECT-TYPE
SYNTAX MplsLdpGenAddr
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The outgoing label of this LSP."
::= { mplsLdpLibEntry 6 }
--
-- Mpls Ldp FEC Table
--
mplsLdpFecTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsLdpFecEntry
Expires April 2000 [Page 38]
INTERNET-DRAFT MPLS LDP MIB October 1999
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table represents the FEC
(Forwarding Equivalence Class)
Information associated with an LSP.
The table is read-only."
::= { mplsLdpLibObjects 2 }
mplsLdpFecEntry OBJECT-TYPE
SYNTAX MplsLdpFecEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each row represents a single FEC Element."
INDEX { mplsLdpFecType,
mplsLdpFecAddressFamily,
mplsLdpFecAddressLength,
mplsLdpFecAddress }
::= { mplsLdpFecTable 1 }
MplsLdpFecEntry ::= SEQUENCE {
mplsLdpFecType INTEGER,
mplsLdpFecAddressFamily AddressFamilyNumbers,
mplsLdpFecAddressLength Integer32(0..255),
mplsLdpFecAddress MplsLdpGenAddr,
mplsLdpFecLspId Unsigned32
}
mplsLdpFecType OBJECT-TYPE
SYNTAX INTEGER {
prefix(1),
hostAddress(2)
}
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The type of the FEC. If the value of this object
is 'prefix(1)' then the FEC type described by this
row is for address prefixes.
If the value of this object is 'hostAddress(2)' then
the FEC type described by this row is a host address."
::= { mplsLdpFecEntry 1 }
mplsLdpFecAddressFamily OBJECT-TYPE
SYNTAX AddressFamilyNumbers
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
Expires April 2000 [Page 39]
INTERNET-DRAFT MPLS LDP MIB October 1999
"The value of this object is from the Address Family
Numbers."
::= { mplsLdpFecEntry 2 }
mplsLdpFecAddressLength OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"If the value of 'mplsLdpFecType' is 'prefix(1)'
then the value of this object is the length in
bits of the address prefix represented by
'mplsLdpFecAddress', or if the length is zero then
this is a special value which indicates that the
prefix matches all addresses. In this case the
prefix is also zero (i.e. 'mplsLdpFecAddress' will
have the value of zero.)"
::= { mplsLdpFecEntry 3 }
mplsLdpFecAddress OBJECT-TYPE
SYNTAX MplsLdpGenAddr
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"If the value of 'mplsLdpFecType' is 'prefix(1)'
then the value of this object is the address prefix.
If the value of the 'mplsLdpFecAddressLength'
is object is zero, then this object should also be
zero."
::= { mplsLdpFecEntry 4 }
mplsLdpFecLspId OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This number represents the LSP which is related to
this FEC. The value of this object should correspond
to an entry in the MplsLdpLibTable, as denoted by
the 'mplsLdpLibLspId' object. In other words, this
object and the 'mplsLdpLibLspId' should have the same
value."
::= { mplsLdpFecEntry 5 }
Expires April 2000 [Page 40]
INTERNET-DRAFT MPLS LDP MIB October 1999
---
--- Notifications
---
mplsLdpNotificationPrefix OBJECT IDENTIFIER ::=
{ mplsLdpNotifications 0 }
mplsLdpFailedInitSessionThresholdExceeded NOTIFICATION-TYPE
OBJECTS {
mplsLdpEntityFailedInitSessionThreshold
}
STATUS current
DESCRIPTION
"This notification is generated whenever the value
of mplsLdpEntityFailedInitSessionThreshold is
exceeded."
::= { mplsLdpNotificationPrefix 1 }
mplsLdpPathVectorLimitMismatch NOTIFICATION-TYPE
OBJECTS {
mplsLdpPeerPathVectorLimit,
mplsLdpSessionPathVectorLimit
}
STATUS current
DESCRIPTION
"This notification is generated when the value
of mplsLdpSessionPathVectorLimit does NOT match
the value of the mplsLdpPeerPathVectorLimit for
the corresponding mplsLdpPeerEntry."
REFERENCE
"LDP Specification, Section 3.5.3."
::= { mplsLdpNotificationPrefix 2 }
--********************************************************************
-- Module Conformance Statement
--********************************************************************
mplsLdpGroups
OBJECT IDENTIFIER ::= { mplsLdpConformance 1 }
mplsLdpCompliances
OBJECT IDENTIFIER ::= { mplsLdpConformance 2 }
--
-- Compliance Statements
--
Expires April 2000 [Page 41]
INTERNET-DRAFT MPLS LDP MIB October 1999
mplsLdpModuleCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The basic implentation requirements for agents that support
the MPLS LDP MIB."
MODULE -- this module
MANDATORY-GROUPS { mplsLdpGeneralGroup,
mplsLdpNotificationsGroup
}
GROUP mplsLdpAtmGroup
DESCRIPTION
"This group must be supported if ATM is used in the
MPLS LDP implementation."
GROUP mplsLdpFrameRelayGroup
DESCRIPTION
"This group must be supported if Frame Relay is used in the
MPLS LDP implementation."
::= { mplsLdpCompliances 1 }
-- units of conformance
mplsLdpGeneralGroup OBJECT-GROUP
OBJECTS {
mplsLdpLsrId,
mplsLdpLsrLabelRetentionMode,
mplsLdpEntityWellKnownDiscoveryPort,
mplsLdpEntityMtu,
mplsLdpEntityKeepAliveHoldTimer,
mplsLdpEntityFailedInitSessionThreshold,
mplsLdpEntityLabelDistributionMethod,
mplsLdpEntityOptionalParameters,
mplsLdpEntityRowStatus,
mplsLdpAttemptedSessions,
mplsLdpSessionRejectedNoHelloErrors,
mplsLdpSessionRejectedAdvertisementErrors,
mplsLdpSessionRejectedMaxPduErrors,
mplsLdpSessionRejectedLabelRangeErrors,
mplsLdpBadLdpIdentifierErrors,
mplsLdpBadPduLengthErrors,
mplsLdpBadMessageLengthErrors,
mplsLdpBadTlvLengthErrors,
mplsLdpMalformedTlvValueErrors,
mplsLdpKeepAliveTimerExpiredErrors,
mplsLdpShutdownNotifReceived,
mplsLdpShutdownNotifSent,
mplsLdpPeerInternetworkAddrType,
mplsLdpPeerInternetworkAddr,
mplsLdpPeerLabelDistributionMethod,
mplsLdpPeerLoopDetectionForPV,
Expires April 2000 [Page 42]
INTERNET-DRAFT MPLS LDP MIB October 1999
mplsLdpPeerPathVectorLimit,
mplsLdpSessionState,
mplsLdpSessionProtocolVersion,
mplsLdpSessionKeepAliveHoldTimeRemaining,
mplsLdpSessionLabelAdvertisement,
mplsLdpSessionLoopDetectionForPV,
mplsLdpSessionPathVectorLimit,
mplsLdpSessionMaxPduLength,
mplsLdpSessionStatsUnknownMessageTypeErrors,
mplsLdpSessionStatsUnknownTlvErrors,
mplsLdpSessionPeerNextHopAddressType,
mplsLdpSessionPeerNextHopAddress,
mplsLdpHelloAdjacencyHoldTimeRemaining,
mplsLdpHelloAdjacencyType,
mplsLdpLibLabelInIfIndex,
mplsLdpLibLabelOutIfIndex,
mplsLdpLibLabelType,
mplsLdpLibInLabel,
mplsLdpLibOutLabel,
mplsLdpFecLspId
}
STATUS current
DESCRIPTION
"Objects that apply to all MPLS LDP implementations."
::= { mplsLdpGroups 1 }
mplsLdpAtmGroup OBJECT-GROUP
OBJECTS {
mplsLdpEntityAtmMergeCap,
mplsLdpEntityAtmLabelRangeComponents,
mplsLdpEntityAtmVcDirectionality,
mplsLdpEntityAtmRowStatus,
mplsLdpEntityConfAtmLabelRangeMinimumVpi,
mplsLdpEntityConfAtmLabelRangeMinimumVci,
mplsLdpEntityConfAtmLabelRangeMaximumVpi,
mplsLdpEntityConfAtmLabelRangeMaximumVci,
mplsLdpEntityConfAtmLabelRangeRowStatus,
mplsLdpSessionAtmLabelRangeLowerBoundVpi,
mplsLdpSessionAtmLabelRangeLowerBoundVci,
mplsLdpSessionAtmLabelRangeUpperBoundVpi,
mplsLdpSessionAtmLabelRangeUpperBoundVci
}
STATUS current
DESCRIPTION
"Objects that apply to all MPLS LDP implementations over ATM."
::= { mplsLdpGroups 2 }
Expires April 2000 [Page 43]
INTERNET-DRAFT MPLS LDP MIB October 1999
mplsLdpFrameRelayGroup OBJECT-GROUP
OBJECTS {
mplsLdpEntityFrMergeCap,
mplsLdpEntityFrLabelRangeComponents,
mplsLdpEntityFrVcDirectionality,
mplsLdpEntityFrParmsRowStatus,
mplsLdpConfFrLen,
mplsLdpConfFrMinimumDlci,
mplsLdpConfFrMaximumDlci,
mplsLdpConfFrRowStatus,
mplsLdpFrSessionLen,
mplsLdpFrSessionMinDlci,
mplsLdpFrSessionMaxDlci
}
STATUS current
DESCRIPTION
"Objects that apply to all MPLS LDP implementations over
Frame Relay."
::= { mplsLdpGroups 3 }
mplsLdpNotificationsGroup NOTIFICATION-GROUP
NOTIFICATIONS { mplsLdpFailedInitSessionThresholdExceeded,
mplsLdpPathVectorLimitMismatch
}
STATUS current
DESCRIPTION
"The notification(s) which an MPLS LDP implemention
is required to implement."
::= { mplsLdpGroups 4 }
END
Expires April 2000 [Page 44]
INTERNET-DRAFT MPLS LDP MIB October 1999
5. Revision History
This section should be removed when this document is published as an
RFC.
5.1. Changes from <draft-ietf-mpls-ldp-mib-01.txt>
The MIB was updated to correspond to draft-ietf-mpls-ldp-06.txt of
the LDP Specification [18].
The front section was updated.
The MIB was made to be less ATM-centric. Essentially, the ATM
specific objects where removed from the tables and placed in ATM
specific Tables. A "type" was added to the "base" tables and a row
is to be created in the ATM/FR/etc. "type" table. Apropos
compliance statements were added to reflect the separation of ATM and
Frame Relay objects into their respective tables.
Objects for Loop Detection were removed from describing the LDP
implementation (i.e. the scalars were removed) and Loop Dection
objects were added to the Session Table. (Although as the LDP
Specification indicates loop detection should be for an LSR within a
domain.)
The following tables were added: mplsLdpEntityAtmParmsTable,
mplsLdpEntityConfAtmLabelRangeTable, mplsLdpFrameRelayParmsTable,
mplsLdpConfFrLabelRangeTable, mplsLdpAtmSessionTable,
mpslLdpFrameRelaySessionTable, mplsLdpSessionPeerAddressTable,
mplsLdpLibTable, and the mplsLdpFecTable.
The following notifications were added: notification for Session
removal.
The following objects were removed from the Session Table:
mplsLdpSessionRole was removed (this can be determined by comparing
LSR Ids and does not need to be explicitely in the MIB.) ATM
specific objects (mplsLdpSessionAtmLabelRangeLowerBoundVpi
mplsLdpSessionAtmLabelRangeLowerBoundVci,
mplsLdpSessionAtmLabelRangeUpperBoundVpi
mplsLdpSessionAtmLabelRangeUpperBoundVci) were removed and put into a
separate table. Frame Relay objects were added in a separate table.
Hello Adjacency Table was updated.
The objects, mplsLdpSessionRejectedParamErrors,
mplsLdpSessionRejectedNoHelloErrors, mplsLdpBadLdpIdentifierErrors,
mplsLdpBadPduLengthErrors, mplsLdpBadMessageLengthErrors,
mplsLdpBadTlvLengthErrors, mplsLdpMalformedTlvValueErrors,
mplsLdpKeepAliveTimerExpiredErrors, mplsLdpShutdownNotifReceived, and
Expires April 2000 [Page 45]
INTERNET-DRAFT MPLS LDP MIB October 1999
mplsLdpShutdownNotifSent were added to the mplsLdpEntityStatsTable.
The mplsLdpSessionStatsTable was added to count statics based on a
per Session basis.
The mplLdpPeerConfAtmLabelRangeTable has been removed. There is no
need to configure information for a Peer. All information for a peer
is learned, thus peer information is read-only.
(Editorial) References were updated to reflect the documents which
this version was based on.
5.2. Changes from <draft-ietf-mpls-ldp-mib-00.txt>
Textual conventions were added for the LSR Identifier and the LDP
Identifier.
Top-level mib structure was added. The LDP MIB falls under a proposed
hierarchy of mpls.mplsProtocols.
The mib hierarchy within the LDP MIB was also changed. A new branch,
under mpls.mplsProtocols.mplsLdpMIB.mplsLdpObjects was added. This
branch is mplsLdpLsrObjects. Currently, this contains several new
scalar objects: mplsLdpLsrID, mplsLdpLsrLoopDetectionPresent,
mplsLdpLsrLoopDetectinAdminStatus, mplsLdpLsrPathVectorLimit,
mplsLdpLsrHopCountLimit, mplsLdpLsrLoopPreventionPresent,
mplsLdpLsrLoopPreventionAdminStatus, and
mplsLdpLsrLabelRetentionMode.
mplsLdpEntityTable is now indexed by mplsLdpEntityIdentifier, which
is the LDP Identifier used in Session establishment.
mplsLdpEntityLoopDetection and mplsLdpEntityLoopPrevention objects
were removed from this table.
The following objects were added to the mplsLdpEntityTable:
mplsLdpEntityLabelSpaceType, mplsLdpEntityUnlabTrafVpi,
mplsLdpEntityUnlabTrafVci, mplsLdpEntityMergeCapability,
mplsLdpEntityVcDirectionality, and
mplsLdpEntityLabelDistributionMethod.
The following objects were added to the mplsLdpPeerEntityTable:
mplsLdpPeerLabelDistributionMethod.
The following object was removed from the mplsLdpEntityStatsTable:
mplsLdpEntityEstablishedSessions.
References were added and revised.
Expires April 2000 [Page 46]
INTERNET-DRAFT MPLS LDP MIB October 1999
6. TO DO List
This section should be removed when this document is published as an
RFC. This section outlines the next areas the authors intend to
address in subsequent revisions.
o Remove the following sections prior to final publication: IANA
Considerations Section, Revisions Section and this (TO DO List)
Section.
o Updates as suggested by review of working group.
7. Acknowledgments
The authors would like to thank the following people: Leigh
McLellan, Geetha Brown, Geping Chen and Charlan Zhou from Nortel
Networks, and Zoltan Takacs and Bo Augustsson from Ericsson.
Expires April 2000 [Page 47]
INTERNET-DRAFT MPLS LDP MIB October 1999
8. References
[RFC2571] Harrington, D., Presuhn, R., and B. Wijnen, "An Architecture
for Describing SNMP Management Frameworks", RFC 2571, April
1999
[RFC1155] Rose, M., and K. McCloghrie, "Structure and Identification
of Management Information for TCP/IP-based Internets", STD
16, RFC 1155, May 1990
[RFC1212] Rose, M., and K. McCloghrie, "Concise MIB Definitions", STD
16, RFC 1212, March 1991
[RFC1215] M. Rose, "A Convention for Defining Traps for use with the
SNMP", RFC 1215, March 1991
[RFC2578] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J.,
Rose, M., and S. Waldbusser, "Structure of Management
Information Version 2 (SMIv2)", STD 58, RFC 2578, April 1999
[RFC2579] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J.,
Rose, M., and S. Waldbusser, "Textual Conventions for
SMIv2", STD 58, RFC 2579, April 1999
[RFC2580] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J.,
Rose, M., and S. Waldbusser, "Conformance Statements for
SMIv2", STD 58, RFC 2580, April 1999
[RFC1157] Case, J., Fedor, M., Schoffstall, M., and J. Davin, "Simple
Network Management Protocol", STD 15, RFC 1157, May 1990.
[RFC1901] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser,
"Introduction to Community-based SNMPv2", RFC 1901, January
1996.
[RFC1906] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser,
"Transport Mappings for Version 2 of the Simple Network
Management Protocol (SNMPv2)", RFC 1906, January 1996.
[RFC2572] Case, J., Harrington D., Presuhn R., and B. Wijnen, "Message
Processing and Dispatching for the Simple Network Management
Protocol (SNMP)", RFC 2572, April 1999
[RFC2574] Blumenthal, U., and B. Wijnen, "User-based Security Model
(USM) for version 3 of the Simple Network Management
Protocol (SNMPv3)", RFC 2574, April 1999
[RFC1905] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser,
"Protocol Operations for Version 2 of the Simple Network
Management Protocol (SNMPv2)", RFC 1905, January 1996.
Expires April 2000 [Page 48]
INTERNET-DRAFT MPLS LDP MIB October 1999
[RFC2573] Levi, D., Meyer, P., and B. Stewart, "SNMPv3 Applications",
RFC 2573, April 1999
[RFC2575] Wijnen, B., Presuhn, R., and K. McCloghrie, "View-based
Access Control Model (VACM) for the Simple Network
Management Protocol (SNMP)", RFC 2575, April 1999
[RFC2570] Case, J., Mundy, R., Partain, D., and B. Stewart,
"Introduction to Version 3 of the Internet-standard Network
Management Framework", RFC 2570, April 1999
[17] Narten, T., and H. Alvestrand, "Guidelines for Writing an IANA
Considerations Section in RFCs.", RFC 2434, IBM, Maxware, October
1998
[18] Andersson, L., Doolan, P., Feldman, N., Fredette, A., and Thomas,
B., "LDP Specification.", draft-ietf-mpls-ldp-06.txt, Nortel
Networks, Ennovate Networks, IBM, Nortel Networks, Cisco Systems
October 1999
[19] Callon, R., Doolan, P., Feldman, N., Fredette, A., Swallow, G., and
A. Viswanathan, "A Framework for Multiprotocol Label Switching",
draft-ietf-mpls-framework-04.txt, IronBridge Networks, Ennovate
Networks, IBM, Nortel Networks, Cisco Systems, July 1999.
[20] Rosen, E., Viswananthan, A., and R. Callon, "Multiprotocol Label
Switching Architecture", draft-ietf-mpls-arch-06.txt, Cisco
Systems, Lucent Technologies, and IronBridge Networks, August 1999.
[21] Jamoussi, B., editor, "Constraint-Based LSP Setup using LDP",
draft-ietf-mpls-cr-ldp-02.txt, August 1999.
[22] Bradner, S., "Key words for use in RFCs to Indicate Requirement
Levels", BCP 14, RFC 2119, Harvard University, March 1997
[23] Bradner, S., "The Internet Standards Process -- Revision 3", BCP 9,
RFC 2026, Harvard University, October 1996
[24] Srinivansan, C., and A. Viswanathan, "MPLS Traffic Engineering
Management Information Base Using SMIv2", draft-ietf-mpls-te-mib-
01.txt, Lucent Technologies, June 1999.
[25] Srinivansan, C., and A. Viswanathan, "MPLS Label Switch Router
Management Information Base Using SMIv2", draft-ietf-mpls-lsr-mib-
00.txt, Lucent Technologies, June 1999.
[26] Greene, M., J. Cucchiara, J. Luciani, "Definition of Managed
Objects for the NBMA Next Hop Resolution Protocol (NHRP)", RFC
2677, August 1999.
Expires April 2000 [Page 49]
INTERNET-DRAFT MPLS LDP MIB October 1999
[27] Internet Assigned Numbers Authority (IANA), ADDRESS FAMILY NUMBERS,
(http://www.isi.edu/in-notes/iana/assignements/address-family-
numbers), for MIB
(ftp://ftp.isi.edu/mib/ianaaddressfamilynumbers.mib).
[28] Noto, M., E. Spiegel, K. Tesink, "Definition of Textual Conventions
and OBJECT-IDENTITIES for ATM Management", RFC 2514, February 1999.
[29] McCloghrie, K., F. Kastenholz, "The Interfaces Group MIB using
SMIv2", RFC 2233, November 1997.
[30] Tesink, K. (ed.) "Definitions of Managed Objects for ATM
Management", RFC 2515, February 1999.
[31] Grossman, D., and J. Heinanen, "Multiprotocol Encapsulation over
ATM Adaptation Layer 5", RFC 2684, September 1999.
9. Security Considerations
Assuming that secure network management (such as SNMP v3) is
implemented, the objects represented in this MIB do not pose a threat
to the security of the network.
10. Authors' Addresses
James V. Luciani
Nortel Networks
3 Federal Street
Mail Stop: BL3-03
Billerica, MA 01821
Phone: (978) 288-4734
Email: luciani@baynetworks.com
Hans Sjostrand
Ericsson
Business Unit Datacom Networks and IP Services
S-126 25 Stockholm, Sweden
Phone: +46 8 719 9960
Email: hans.sjostrand@etx.ericsson.se
Joan Cucchiara
IronBridge Networks
55 Hayden Ave., Suite 1000
Lexington, MA 02421
Phone: (781) 372-8236
Email: joan@ironbridgenetworks.com
Expires April 2000 [Page 50]
INTERNET-DRAFT MPLS LDP MIB October 1999
11. Full Copyright Statement
Copyright (C) The Internet Society (1999). All Rights Reserved.
This document and translations of it may be copied and furnished to
others, and derivative works that comment on or otherwise explain it
or assist in its implementation may be prepared, copied, published
and distributed, in whole or in part, without restriction of any
kind, provided that the above copyright notice and this paragraph are
included on all such copies and derivative works. However, this
document itself may not be modified in any way, such as by removing
the copyright notice or references to the Internet Society or other
Internet organizations, except as needed for the purpose of
developing Internet standards in which case the procedures for
copyrights defined in the Internet Standards process must be
followed, or as required to translate it into languages other than
English.
The limited permissions granted above are perpetual and will not be
revoked by the Internet Society or its successors or assigns.
This document and the information contained herein is provided on an
"AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
12. IANA Address Family Numbers MIB
This section is copied verbatim from the RFC2677 [26]. This section
will be removed in future versions of this draft. This section was
copied here for convenience, as it is IMPORTED into the LDP MIB.
The Internet Assigned Numbers Authority (IANA) has been and continues
to be responsible for maintaining the ADDRESS FAMILY NUMBERS
(http://www.isi.edu/in-notes/iana/assignments/address-family-numbers)
name space assignments. The IANA has placed this list in a MIB
module, such that it may be imported into other MIBs. The motivation
for doing this is to allow MIBs to not have to change when a new
assignment is made to the ADDRESS FAMILY NUMBERS. This is very
similar to the motivation behind the IANAifType-MIB.
Any additions or changes to the list of ADDRESS FAMILY NUMBERS
registered via IANA will be done as they have in the past and this
document does not propose any changes to the ADDRESS FAMILY NUMBERS
other than to place them into a MIB, which can be found via anonymous
Expires April 2000 [Page 51]
INTERNET-DRAFT MPLS LDP MIB October 1999
FTP at: ftp://ftp.isi.edu/mib/ianaaddressfamilynumbers.mib.
Expires April 2000 [Page 52]
INTERNET-DRAFT MPLS LDP MIB October 1999