Internet Draft Network Working Group Cheenu Srinivasan Internet Draft Tachion Networks, Inc. Expires: October 2000 Arun Viswanathan Force10 Networks, Inc. Thomas D. Nadeau Cisco Systems, Inc. MPLS Label Switch Router Management Information Base Using SMIv2 draft-ietf-mpls-lsr-mib-04.txt Status of this Memo This document is an Internet-Draft and is in full conformance with all provisions of Section 10 of RFC 2026. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet- Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet- Drafts as reference material or to cite them other than as "work in progress." The list of current Internet-Drafts can be accessed at http://www.ietf.org/ietf/1id-abstracts.txt. The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html. Table of Contents 1.Abstract..............................................2 2. Introduction.........................................2 3. Terminology..........................................2 4. The SNMP Management Framework........................3 4.1. Object Definitions.................................4 5. Feature Checklist....................................4 6. Outline..............................................5 6.1. Summary of LSR MIB.................................5 7. Brief Description of MIB Objects.....................5 7.1. mplsInterfaceConfTable.............................6 7.2. mplsInterfacePerfTable.............................6 7.3. mplsInSegmentTable.................................6 7.4. mplsInSegmentPerfTable.............................7 7.5. mplsOutSegmentTable................................7 7.6. mplsOutSegmentPerfTable............................7 Srinivasan et al. Expires October 2000 [Page 1] Internet Draft MPLS LSR MIB April 26, 2000 7.7. mplsXCTable........................................8 7.8. mplsLabelStackTable................................8 7.9. mplsTrafficParamTable..............................8 8. Example of LSP Setup.................................8 9. Application of the Interface Group to MPLS..........10 9.1. Support of the MPLS Layer by ifTable..............10 10. The Use of RowPointer..............................12 11. MPLS Label Switch Router MIB Definitions...........12 12. Security Considerations............................53 13. Acknowledgments....................................54 14. References.........................................55 15. Authors' Addresses.................................57 16. Full Copyright Statement...........................58 1. Abstract This memo defines an experimental portion of the Management Information Base (MIB) for use with network management protocols in the Internet community. In particular, it describes managed objects for modeling a Multi-Protocol Label Switching (MPLS) [MPLSArch, MPLSFW] Label Switch Router (LSR). 2. Introduction This memo defines an experimental portion of the Management Information Base (MIB) for use with network management protocols in the Internet community. In particular, it describes managed objects for modeling a Multi-Protocol Label Switching (MPLS) [MPLSArch, MPLSFW] Label Switch Router (LSR). Comments should be made directly to the MPLS mailing list at mpls@uu.net. This memo does not, in its draft form, specify a standard for the Internet community. The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119, reference [BCP14]. 3. Terminology This document uses terminology from the document describing the MPLS architecture [MPLSArch]. A label switched path (LSP) is modeled as a connection consisting of one or more incoming segments (in-segments) and/or one or more outgoing segments (out- segments) at a label switch router (LSR). The association or Srinivasan et al. Expires October 2000 [Page 2] Internet Draft MPLS LSR MIB April 26, 2000 interconnection of the in-segments and out-segments is accomplished by using a cross-connect. We use the terminology "connection" and "LSP" interchangeably where the meaning is clear from the context. 4. The SNMP Management Framework The SNMP Management Framework presently consists of five major components: - An overall architecture, described in RFC 2271 [SNMPArch]. - Mechanisms for describing and naming objects and events for the purpose of management. The first version of this Structure of Management Information (SMI) is called SMIv1 and described in RFC 1155 [SMIv1], RFC 1212 [SNMPv1MIBDef] and RFC 1215 [SNMPv1Traps]. The second version, called SMIv2, is described in RFC 1902 [SMIv2], RFC 1903 [SNMPv2TC] and RFC 1904 [SNMPv2Conf]. - Message protocols for transferring management information. The first version of the SNMP message protocol is called SNMPv1 and described in RFC 1157 [SNMPv1]. A second version of the SNMP message protocol, which is not an Internet standards track protocol, is called SNMPv2c and described in RFC 1901 [SNMPv2c] and RFC 1906 [SNMPv2TM]. The third version of the message protocol is called SNMPv3 and described in RFC 1906 [SNMPv2TM], RFC 2272 [SNMPv3MP] and RFC 2574 [SNMPv3USM]. - Protocol operations for accessing management information. The first set of protocol operations and associated PDU formats is described in RFC 1157 [SNMPv1]. A second set of protocol operations and associated PDU formats is described in RFC 1905 [SNMPv2PO]. - A set of fundamental applications described in RFC 2273 [SNMPv3App] and the view-based access control mechanism described in RFC 2575 [SNMPv3VACM]. Managed objects are accessed via a virtual information store, termed the Management Information Base or MIB. Objects in the MIB are defined using the mechanisms defined in the SMI. This memo specifies a MIB module that is compliant to the SMIv2. A MIB conforming to the SMIv1 can be produced through the appropriate translations. The resulting translated MIB must be semantically equivalent, except where objects or events are omitted because no translation is possible (use of Counter64). Some machine-readable information in SMIv2 will be converted into textual descriptions in SMIv1 during the translation process. However, this loss of Srinivasan et al. Expires October 2000 [Page 3] Internet Draft MPLS LSR MIB April 26, 2000 machine-readable information is not considered to change the semantics of the MIB. 4.1. Object Definitions Managed objects are accessed via a virtual information store, termed the Management Information Base or MIB. Objects in the MIB are defined using the subset of Abstract Syntax Notation One (ASN.1) defined in the SMI. In particular, each object type is named by an OBJECT IDENTIFIER, an administratively assigned name. The object type together with an object instance serves to uniquely identify a specific instantiation of the object. For human convenience, we often use a textual string, termed the descriptor, to also refer to the object type. 5. Feature Checklist The MPLS label switch router MIB (LSR-MIB) is designed to satisfy the following requirements and constraints: - The MIB supports both manually configured LSPs as well as those configured via any MPLS signaling protocol. - The MIB supports the enabling and disabling of MPLS capability on MPLS capable interfaces of an LSR. - The MIB allows resource sharing between two or more LSPs. - Both per-platform and per-interface label spaces are supported. - MPLS packets can be forwarded solely based on an incoming top label [MPLSArch, LblStk]. - Support is provided for next-hop resolution when the outgoing interface is a shared media interface. In the point-to- multipoint case, each outgoing segment can reside on a different shared media interface. - The MIB supports point-to-point, point-to-multipoint and multipoint-to-point connections at an LSR. - For multipoint-to-point connections all outgoing packets can have the same top label. - For multipoint-to-point connections, the outgoing resources of the merged connections can be shared. - For multipoint-to-point connections, packets from different Srinivasan et al. Expires October 2000 [Page 4] Internet Draft MPLS LSR MIB April 26, 2000 incoming connections can have distinct outgoing label stacks beneath the (identical) top label. - In the point-to-multipoint case each outgoing connection can have a distinct label stack including the top label. - All the members of a point-to-multipoint connection can share the resources allocated for the ingress segments. - The MIB provides cross-connect capability to "pop" an incoming label and forward the packet with the remainder of the label stack unchanged and without pushing any labels ("pop-and-go") [LblStk]. - The MIB supports persistent as well as non-persistent LSPs. - Performance counters are provided for in-segments and out- segments as well as for measuring MPLS performance on a per- interface basis. 6. Outline Configuring LSPs through an LSR involves the following steps: - Enabling MPLS on MPLS capable interfaces. - Configuring in-segments and out-segments. - Setting up the cross-connect table to associate segments and/or to indicate connection origination and termination. - Optionally specifying label stack actions. - Optionally specifying segment traffic parameters. 6.1. Summary of LSR MIB The MIB objects for performing these actions consist of the following tables: - The interface configuration table (mplsInterfaceConfTable), which is used for enabling the MPLS protocol on MPLS-capable interfaces. - The in-segment (mplsInSegmentTable) and out-segment (mplsOutSegmentTable) tables, which are used for configuring LSP segments at an LSR. Srinivasan et al. Expires October 2000 [Page 5] Internet Draft MPLS LSR MIB April 26, 2000 - The cross-connect table (mplsXCTable), which is used to associate in and out segments together, in order to form a cross-connect. - The label stack table (mplsLabelStackTable), which is used for specifying label stack operations. - The Traffic Parameter table (mplsTrafficParamTable), which is used for specifying LSP-related traffic parameters. Further, the MPLS in-segment and out-segment performance tables, mplsInSegmentPerfTable and mplsOutSegmentPerfTable, contain the objects necessary to measure the performance of LSPs, and mplsInterfacePerfTable has objects to measure MPLS performance on a per-interface basis. These tables are described in the subsequent sections. 7. Brief Description of MIB Objects Sections 7.1-7.2 describe objects pertaining to MPLS capable interfaces of an LSR. The objects described in Sections 7.3-7.8, when considered together, are equivalent to the tables described in the MPLS architecture document [MPLSArch], that is, the Incoming Label Map (ILM) and the Next Hop Label Forwarding Entry (NHLFE) tables. Section 7.9 describes objects for specifying traffic parameters for in and out segments. It is appropriate to note that the in-segment, out-segment, and cross-connect tables were modeled after similar tables found in [ATOMMIB]. 7.1. mplsInterfaceConfTable This table represents the interfaces that are MPLS capable. An LSR creates an entry in this table for every MPLS capable interface on that LSR. 7.2. mplsInterfacePerfTable This table contains objects to measure the MPLS performance of MPLS capable interfaces and is an AUGMENT to mplsInterfaceConfTable. High capacity counters are provided for objects that are likely to wrap around quickly on high-speed interfaces. 7.3. mplsInSegmentTable Srinivasan et al. Expires October 2000 [Page 6] Internet Draft MPLS LSR MIB April 26, 2000 This table contains a description of the incoming MPLS segments to an LSR and their associated parameters. The administrative and operational status objects for this table are used to control packet transmission on this segment. If either the administrative and operational status objects for this table are set to 'down', this implies that packets will not be forwarded. Likewise, if the values are set to 'up' this implies that packets are forwarded. These values are particularly useful in cases where multi-point connections utilize a single cross- connect and the administrator wishes to disable some, but not all of the streams. In these cases, the administrator may set the administrative status object to 'down' on some of the in-segments. 7.4. mplsInSegmentPerfTable The MPLS In-Segment Performance Table has objects to measure the performance of an incoming segment configured on an LSR. It is an AUGMENT to mplsInSegmentTable. High capacity counters are provided for objects that are likely to wrap around quickly on high-speed interfaces. 7.5. mplsOutSegmentTable The Out-Segment Table contains a description of the outgoing MPLS segments at an LSR and their associated parameters. The administrative and operational status objects for this table are used to control packet transmission on this segment. If either the administrative and operational status objects are set to 'down', this implies that packets will not be forwarded. Likewise, if the values are set to 'up' this implies that packets are forwarded. These values are particularly useful in cases where multicast connections utilize a single cross-connect and the administrator wishes to disable some, but not all of the streams. In these cases, the administrator may set the administrative status object to 'down' on some of the out-segments. 7.6. mplsOutSegmentPerfTable The MPLS Out-Segment Table contains objects to measure the performance of an outgoing segment configured on an LSR. It is an AUGMENT to mplsOutSegmentTable. High capacity counters are provided for objects that are likely to wrap around quickly on high-speed interfaces. Srinivasan et al. Expires October 2000 [Page 7] Internet Draft MPLS LSR MIB April 26, 2000 7.7. mplsXCTable The mplsXCTable specifies information for associating segments together in order to instruct the LSR to switch between the specified segments. It supports point-to-point, point-to-multi- point and multi-point-to-point connections. The administrative and operational status objects for this table imply control of packet forwarding to and from a XCEntry. When the administrative and operational status objects are set to 'down' for example, this implies that the specified XCEntry will not forward packets. Likewise, when either is set to 'up' this implies that packets will be forwarded. 7.8. mplsLabelStackTable The mplsLabelStackTable specifies the label stack to be pushed onto a packet, beneath the top label. Entries to this table are referred to from mplsXCTable. 7.9. mplsTrafficParamTable The mplsTrafficParamTable contains objects for specifying the traffic parameters of in-segments and out-segments. Entries in this table are referred to from mplsInSegmentTable and mplsOutSegmentTable. 8. Example of LSP Setup In this section we provide a brief example of using the MIB objects described in section 11. to set up an LSP. While this example is not meant to illustrate every nuance of the MIB, it is intended as an aid to understanding some of the key concepts. It is meant to be read after going through the MIB itself. Suppose that one would like to manually create a best-effort, unidirectional LSP. Assume that the LSP enters the LSR via MPLS interface A with ifIndex 12 and exits the LSR via MPLS interface B with ifIndex 13. Let us assume that we do not wish to have a label stack beneath the top label on the outgoing labeled packets. The following example illustrates which rows and corresponding objects might be created to accomplish this. First, the traffic parameter entries must be set-up for both segments. In mplsTrafficParamTable for the incoming direction: Srinivasan et al. Expires October 2000 [Page 8] Internet Draft MPLS LSR MIB April 26, 2000 { mplsTrafficParamIndex = 5 mplsTrafficParamMaxRate = 100000, mplsTrafficParamMeanRate = 100000, mplsTrafficParamMaxBurstSize = 2000, mplsTrafficParamRowStatus = createAndGo(4) } In mplsTrafficParamTable for the outgoing direction: { mplsTrafficParamIndex = 6 mplsTrafficParamMaxRate = 100000, mplsTrafficParamMeanRate = 100000, mplsTrafficParamMaxBurstSize = 2000, mplsTrafficParamRowStatus = createAndGo(4) } Note that if we were setting up a bi-directional LSP, the segments in the reverse direction can share the traffic parameter entries (and hence resources) with the segments in the forward direction. We must next create the appropriate in-segment and out-segment entries with suitable traffic parameters by pointing to the appropriate traffic parameter entries that we have just created. In mplsInSegmentTable: { mplsInSegmentIfIndex = 12, -- incoming interface mplsInSegmentLabel = 21, -- incoming label mplsInSegmentNPop = 1, mplsInSegmentTrafficParamPtr = mplsTrafficParamIndex.5, mplsInSegmentRowStatus = createAndGo(4) } In mplsOutSegmentTable: { mplsOutSegmentIndex = 1, mplsOutSegmentIfIndex = 13, -- outgoing interface mplsOutSegmentPushTopLabel = true(1), mplsOutSegmentTopLabel = 22, -- outgoing label mplsOutSegmentTrafficParamPtr = mplsTrafficParamIndex.6, mplsOutSegmentRowStatus = createAndGo(4) } Next, a cross-connect entry is created thereby associating the newly created segments together. In mplsXCTable: { Srinivasan et al. Expires October 2000 [Page 9] Internet Draft MPLS LSR MIB April 26, 2000 mplsXCIndex = 2, mplsXCLspId = 'c021041502'H, -- 192.33.4.21.2 mplsInSegmentIfIndex = 12, mplsInSegmentLabel = 21, mplsOutSegmentIndex = 1, mplsXCIsPersistent = false (1), mplsLabelStackIndex = 0, -- only a single -- outgoing label mplsXCRowStatus = createAndGo(4) } Note that the mplsInSegmentXCIndex and mplsOutSegmentXCIndex objects will automatically be populated with the value 2 when these segments are referred to from the corresponding cross- connect entry. 9. Application of the Interface Group to MPLS The Interfaces Group of MIB II defines generic managed objects for managing interfaces. This memo contains the media-specific extensions to the Interfaces Group for managing MPLS interfaces. This memo assumes the interpretation of the Interfaces Group to be in accordance with [IFMIB] which states that the interfaces table (ifTable) contains information on the managed resource's interfaces and that each sub-layer below the internetwork layer of a network interface is considered an interface. Thus, the MPLS interface is represented as an entry in the ifTable. The inter- relation of entries in the ifTable is defined by Interfaces Stack Group defined in [IFMIB]. When using MPLS interfaces, the interface stack table might appear as follows: +----------------------------------------+ | MPLS-interface ifType = mpls(166) + +----------------------------------------+ | Underlying Layer... + +----------------------------------------+ In the above diagram, "Underlying Layer..." refers to the ifIndex of any interface type, which has been defined for MPLS interworking. Examples include ATM, Frame Relay, Ethernet, etc. 9.1. Support of the MPLS Layer by ifTable Some specific interpretations of ifTable for the MPLS layer follow. Srinivasan et al. Expires October 2000 [Page 10] Internet Draft MPLS LSR MIB April 26, 2000 Object Use for the MPLS layer ifIndex Each MPLS interface is represented by an ifEntry. ifDescr Description of the MPLS interface. ifType The value that is allocated for MPLS is 166. ifSpeed The total bandwidth in bits per second for use by the MPLS layer. ifPhysAddress Unused. ifAdminStatus This variable indicates the administrator's intent as to whether MPLS should be enabled, disabled, or running in some diagnostic testing mode on this interface. Also see [IFMIB]. ifOperStatus This value reflects the actual or operational status of MPLS on this interface. ifLastChange See [IFMIB]. ifInOctets The number of received octets over the interface, i.e., the number of received, octets received as labeled packets. ifOutOctets The number of transmitted octets over the interface, i.e., the number of octets transmitted as labeled packets. ifInErrors The number of labeled packets dropped due to uncorrectable errors. ifInUnknownProtos The number of received packets discarded during packet header validation, including packets with unrecognized label values. ifOutErrors See [IFMIB]. ifName Textual name (unique on this system) of the interface or an octet string of zero length. ifLinkUpDownTrapEnable Default is disabled (2). ifConnectorPresent Set to false (2). Srinivasan et al. Expires October 2000 [Page 11] Internet Draft MPLS LSR MIB April 26, 2000 ifHighSpeed See [IFMIB]. ifHCInOctets The 64-bit version of ifInOctets; supported if required by the compliance statements in [IFMIB]. ifHCOutOctets The 64-bit version of ifOutOctets; supported if required by the compliance statements in [IFMIB]. ifAlias The non-volatile 'alias' name for the interface as specified by a network manager. ifCounterDiscontinuityTime See [IFMIB]. 10. The Use of RowPointer RowPointer is a textual convention used to identify a conceptual row in an SNMP Table by pointing to one of its objects. In this MIB, it is used in mplsInSegmentTable and mplsOutSegmentTable for the following purposes. First, it indicates a particular traffic parameter table. An example of such a table is mplsTrafficParamTable. Second, it is used to indicate a specific instance of a traffic parameter entry that is associated with a given in-segment or out-segment entry. In the in-segment and out- segment tables, the trafficParamPtr SHOULD point to the first column of the appropriate conceptual row. 11. MPLS Label Switch Router MIB Definitions MPLS-LSR-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, experimental, Integer32, Counter32, Unsigned32, Counter64, Gauge32, BITS FROM SNMPv2-SMI MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF TEXTUAL-CONVENTION, TruthValue, RowStatus, StorageType, RowPointer, TimeStamp FROM SNMPv2-TC InterfaceIndex, InterfaceIndexOrZero FROM IF-MIB Srinivasan et al. Expires October 2000 [Page 12] Internet Draft MPLS LSR MIB April 26, 2000 AddressFamilyNumbers FROM IANA-ADDRESS-FAMILY-NUMBERS-MIB InetAddressIPv4, InetAddressIPv6, InetAddressType FROM INET-ADDRESS-MIB; mplsLsrMIB MODULE-IDENTITY LAST-UPDATED "200004261200Z" -- 26 April 2000 12:00:00 EST ORGANIZATION "Multiprotocol Label Switching (MPLS) Working Group" CONTACT-INFO " Cheenu Srinivasan Postal: Tachion Networks, Inc. Monmouth Park Corporate Center I Building C, 185 Monmouth Parkway West Long Branch, NJ 07764 Tel: +1-732-542-7750 x1234 Email: cheenu@tachion.com Arun Viswanathan Postal: Force10 Networks, Inc. 1440 McCarthy Blvd Milpitas, CA 95035 Tel: +1-408-571-3516 Email: arun@force10networks.com Thomas D. Nadeau Postal: Cisco Systems, Inc. 250 Apollo Drive Chelmsford, MA 01824 Tel: +1-978-244-3051 Email: tnadeau@cisco.com" DESCRIPTION "This MIB contains managed object definitions for the Multiprotocol Label Switching (MPLS) Router as defined in: Rosen, E., Viswanathan, A., and R. Callon, Multiprotocol Label Switching Architecture, Internet Draft <draft-ietf-mpls-arch-06.txt>, February 2000." -- Revision history. REVISION "199906161200Z" -- 16 June 1999 12:00:00 EST DESCRIPTION "Initial draft version." REVISION "200002161200Z" -- 16 February 2000 12:00:00 EST DESCRIPTION Srinivasan et al. Expires October 2000 [Page 13] Internet Draft MPLS LSR MIB April 26, 2000 "Second draft version." REVISION "200003061200Z" -- 6 March 2000 12:00:00 EST DESCRIPTION "Third draft version." REVISION "200004211200Z" -- 21 April 2000 12:00:00 EST DESCRIPTION "Fourth draft version. Made corrections from WG Last Call comments." REVISION "200004261200Z" -- 26 April 2000 12:00:00 EST DESCRIPTION "Fifth draft version. Made minor typographical corrections noted from WG mailing list." ::= { experimental 96 } -- Textual Conventions. MplsLSPID ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "An identifier that is assigned to each LSP and is used to uniquely identify it. This is assigned at the head end of the LSP and can be used by all LSRs to identify this LSP. This value is piggybacked by the signaling protocol when this LSP is signaled within the network. This identifier can then be used at each LSR to identify which labels are being swapped to other labels for this LSP. For IPv4 addresses this results in a 6-octet long cookie." SYNTAX OCTET STRING (SIZE (0..31)) -- An MPLS label. MplsLabel ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This value represents an MPLS label. Note that the contents of a label field are interpreted in an interface-type specific fashion. For example, the 20-bit wide label carried in the MPLS shim header is contained in bits 0-19 and bits 20-31 must be zero. The frame relay label can be either 10 or 23 bits wide depending on the size of the DLCI field and bits 10-31, or 23-31 must be zero, respectively. For an ATM interface, bits 0-15 must be interpreted as the VCI, bits 16-23 as the VPI and bits 24-31 must be zero. Note that the permissible label values are also a function of the interface type. For example, the value 3 has special semantics in the control plane for an MPLS shim header label and is not a valid label value in the data path." REFERENCE Srinivasan et al. Expires October 2000 [Page 14] Internet Draft MPLS LSR MIB April 26, 2000 "1. MPLS Label Stack Encoding, Rosen et al, draft- ietf-mpls-label-encaps-07.txt, March 2000. 2. Use of Label Switching on Frame Relay Networks, Conta et al, draft-ietf-mpls-fr-03.txt, Nov. 1998. 3. MPLS using LDP and ATM VC switching, Davie et al, draft-ietf-mpls-atm-02.txt, April 1999." SYNTAX Unsigned32 (0..4294967295) MplsBitRate ::= TEXTUAL-CONVENTION DISPLAY-HINT "d" STATUS current DESCRIPTION "An estimate of bandwidth in units of 1,000 bits per second. If this object reports a value of 'n' then the rate of the object is somewhere in the range of 'n-500' to 'n+499'. For objects which do not vary in bitrate, or for those where no accurate estimation can be made, this object should contain the nominal bitrate." SYNTAX Integer32 (1..2147483647) MplsBurstSize ::= TEXTUAL-CONVENTION DISPLAY-HINT "d" STATUS current DESCRIPTION "The number of octets of MPLS data that the stream may send back-to-back without concern for policing." SYNTAX Integer32 (1..2147483647) MplsBufferSize ::= TEXTUAL-CONVENTION DISPLAY-HINT "d" STATUS current DESCRIPTION "Size of buffer in octets of MPLS data." SYNTAX Integer32 (1..2147483647) MplsObjectOwner ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The entity which owns the object in question." SYNTAX INTEGER { other(1), snmp(2), ldp(3), rsvp(4), policyAgent(5), unknown (6) } Srinivasan et al. Expires October 2000 [Page 15] Internet Draft MPLS LSR MIB April 26, 2000 -- Top level components of this MIB. -- Tables, Scalars mplsLsrObjects OBJECT IDENTIFIER ::= { mplsLsrMIB 1 } -- traps mplsLsrNotifications OBJECT IDENTIFIER ::= { mplsLsrMIB 2 } -- conformance mplsLsrConformance OBJECT IDENTIFIER ::= { mplsLsrMIB 3 } -- MPLS Interface Configuration Table. mplsInterfaceConfTable OBJECT-TYPE SYNTAX SEQUENCE OF MplsInterfaceConfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table specifies per-interface MPLS capability and associated information." ::= { mplsLsrObjects 1 } mplsInterfaceConfEntry OBJECT-TYPE SYNTAX MplsInterfaceConfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table is created by an LSR for every interface capable of supporting MPLS. The entry with index 0 represents the per-platform label space and contains parameters that apply to all interfaces that participate in the per-platform label space. Other entries defined in this table represent additional MPLS interfaces that may participate in either the per-platform or per- interface label spaces, or both. Additional information about label space participation of an interface is provided in the description clause of mplsInterfaceLabelParticipationType." INDEX { mplsInterfaceConfIndex } ::= { mplsInterfaceConfTable 1 } MplsInterfaceConfEntry ::= SEQUENCE { mplsInterfaceConfIndex InterfaceIndexOrZero, mplsInterfaceLabelMinIn MplsLabel, mplsInterfaceLabelMaxIn MplsLabel, mplsInterfaceLabelMinOut MplsLabel, mplsInterfaceLabelMaxOut MplsLabel, mplsInterfaceTotalBandwidth MplsBitRate, mplsInterfaceAvailableBandwidth MplsBitRate, mplsInterfaceTotalBuffer MplsBufferSize, Srinivasan et al. Expires October 2000 [Page 16] Internet Draft MPLS LSR MIB April 26, 2000 mplsInterfaceAvailableBuffer MplsBufferSize, mplsInterfaceLabelParticipationType BITS, mplsInterfaceConfStorageType StorageType } mplsInterfaceConfIndex OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS not-accessible STATUS current DESCRIPTION "This is a unique index for an entry in the MplsInterfaceConfTable. A non-zero index for an entry indicates the ifIndex for the corresponding interface entry in of the MPLS-layer in the ifTable. Note that the per-platform label space may apply to several interfaces, and therefore the configuration of the per-platform label space interface parameters will apply to all of the interfaces that are participating in the per-platform label space." REFERENCE "RFC 2233 - The Interfaces Group MIB using SMIv2, McCloghrie, K., and F. Kastenholtz, Nov. 1997" ::= { mplsInterfaceConfEntry 1 } mplsInterfaceLabelMinIn OBJECT-TYPE SYNTAX MplsLabel MAX-ACCESS read-only STATUS current DESCRIPTION "This is the minimum value of an MPLS label that this LSR is willing to receive on this interface." ::= { mplsInterfaceConfEntry 2 } mplsInterfaceLabelMaxIn OBJECT-TYPE SYNTAX MplsLabel MAX-ACCESS read-only STATUS current DESCRIPTION "This is the maximum value of an MPLS label that this LSR is willing to receive on this interface." ::= { mplsInterfaceConfEntry 3 } mplsInterfaceLabelMinOut OBJECT-TYPE SYNTAX MplsLabel MAX-ACCESS read-only STATUS current DESCRIPTION "This is the minimum value of an MPLS label that this LSR is willing to send on this interface." ::= { mplsInterfaceConfEntry 4 } Srinivasan et al. Expires October 2000 [Page 17] Internet Draft MPLS LSR MIB April 26, 2000 mplsInterfaceLabelMaxOut OBJECT-TYPE SYNTAX MplsLabel MAX-ACCESS read-only STATUS current DESCRIPTION "This is the maximum value of an MPLS label that this LSR is willing to send on this interface." ::= { mplsInterfaceConfEntry 5 } mplsInterfaceTotalBandwidth OBJECT-TYPE SYNTAX MplsBitRate MAX-ACCESS read-only STATUS current DESCRIPTION "This value indicates the total amount of usable bandwidth on this interface and is specified in kilobits per second (Kbps). This variable is not applicable when applied to the interface with index 0." ::= { mplsInterfaceConfEntry 6 } mplsInterfaceAvailableBandwidth OBJECT-TYPE SYNTAX MplsBitRate MAX-ACCESS read-only STATUS current DESCRIPTION "This value indicates the total amount of available bandwidth available on this interface and is specified in kilobits per second (Kbps). This value is calculated as the difference between the amount of bandwidth currently in use and that specified in mplsInterfaceTotalBandwidth. This variable is not applicable when applied to the interface with index 0." ::= { mplsInterfaceConfEntry 7 } mplsInterfaceTotalBuffer OBJECT-TYPE SYNTAX MplsBufferSize MAX-ACCESS read-only STATUS current DESCRIPTION "This value indicates the total amount of buffer space allocated for this interface. This variable is not applicable when applied to the interface with index 0." ::= { mplsInterfaceConfEntry 8 } mplsInterfaceAvailableBuffer OBJECT-TYPE SYNTAX MplsBufferSize Srinivasan et al. Expires October 2000 [Page 18] Internet Draft MPLS LSR MIB April 26, 2000 MAX-ACCESS read-only STATUS current DESCRIPTION "This value reflects the total amount of buffer space available on this interface. This variable is not applicable when applied to the interface with index 0." ::= { mplsInterfaceConfEntry 9 } mplsInterfaceLabelParticipationType OBJECT-TYPE SYNTAX BITS { perPlatform (0), perInterface (1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Either the perPlatform(0) or perInterface(1) bit MUST be set. If the value of the mplsInterfaceConfIndex for this entry is zero, then only the perPlatform(0) bit MUST be set and the perInterface(1) bit is meaningless. If the perInterface(1) bit is set then the value of mplsInterfaceLabelMinIn, mplsInterfaceLabelMaxIn, mplsInterfaceLabelMinOut, and mplsInterfaceLabelMaxOut for this entry reflect the label ranges for this interface. If only the perPlatform(0) bit is set, then the value of mplsInterfaceLabelMinIn, mplsInterfaceLabelMaxIn, mplsInterfaceLabelMinOut, and mplsInterfaceLabelMaxOut for this entry must be identical to the instance of these objects with index 0." REFERENCE "Multiprotocol Label Switching, Rosen et al, draft-ietf-mpls- arch-06.txt, August 1999." ::= { mplsInterfaceConfEntry 10 } mplsInterfaceConfStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "The storage type for this entry." ::= { mplsInterfaceConfEntry 11 } -- End of mplsInterfaceConfTable -- MPLS Interface Performance Table. Srinivasan et al. Expires October 2000 [Page 19] Internet Draft MPLS LSR MIB April 26, 2000 mplsInterfacePerfTable OBJECT-TYPE SYNTAX SEQUENCE OF MplsInterfacePerfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides MPLS performance information on a per-interface basis." ::= { mplsLsrObjects 2 } mplsInterfacePerfEntry OBJECT-TYPE SYNTAX MplsInterfacePerfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table is created by the LSR for every interface capable of supporting MPLS. Its is an extension to the mplsInterfaceConfEntry table." AUGMENTS { mplsInterfaceConfEntry } ::= { mplsInterfacePerfTable 1 } MplsInterfacePerfEntry ::= SEQUENCE { -- incoming direction mplsInterfaceInLabelsUsed Gauge32, mplsInterfaceInPackets Counter32, mplsInterfaceInDiscards Counter32, mplsInterfaceFailedLabelLookup Counter32, -- outgoing direction mplsInterfaceOutLabelsUsed Gauge32, mplsInterfaceOutPackets Counter32, mplsInterfaceOutDiscards Counter32, mplsInterfaceOutFragments Counter32 } mplsInterfaceInLabelsUsed OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This value indicates the specific number of labels that are in use at this point in time on this interface in the incoming direction." ::= { mplsInterfacePerfEntry 1 } mplsInterfaceInPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION Srinivasan et al. Expires October 2000 [Page 20] Internet Draft MPLS LSR MIB April 26, 2000 "This variable reflects the number of labeled packets that have been received on this interface." ::= { mplsInterfacePerfEntry 2 } mplsInterfaceInDiscards OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of inbound labeled packets, which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a labeled packet could be to free up buffer space." ::= { mplsInterfacePerfEntry 3 } mplsInterfaceFailedLabelLookup OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This value indicates the number of labeled packets that have been received on this interface and were discarded because there were no matching entries found for them in mplsInSegmentTable." ::= { mplsInterfacePerfEntry 4 } mplsInterfaceOutLabelsUsed OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the number of top-most labels in the outgoing label stacks that are in use at this point in time on this interface." ::= { mplsInterfacePerfEntry 5 } mplsInterfaceOutPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This variable contains the number of labeled packets that have been transmitted on this interface." ::= { mplsInterfacePerfEntry 6 } mplsInterfaceOutDiscards OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current Srinivasan et al. Expires October 2000 [Page 21] Internet Draft MPLS LSR MIB April 26, 2000 DESCRIPTION "The number of outbound labeled packets, which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a labeled packet could be to free up buffer space." ::= { mplsInterfacePerfEntry 7 } mplsInterfaceOutFragments OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates the number of outgoing MPLS packets that required fragmentation before transmission on this interface." ::= { mplsInterfacePerfEntry 8 } -- In-segment table. mplsInSegmentTable OBJECT-TYPE SYNTAX SEQUENCE OF MplsInSegmentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains a collection of incoming segments to an LSR." ::= { mplsLsrObjects 3 } mplsInSegmentEntry OBJECT-TYPE SYNTAX MplsInSegmentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table represents one incoming segment. An entry can be created by a network administrator or an SNMP agent, or an MPLS signaling protocol. The creator of the entry is denoted by mplsInSegmentOwner. An entry in this table is indexed by the ifIndex of the incoming interface and the (top) label." INDEX { mplsInSegmentIfIndex, mplsInSegmentLabel } ::= { mplsInSegmentTable 1 } MplsInSegmentEntry ::= SEQUENCE { mplsInSegmentIfIndex InterfaceIndexOrZero, mplsInSegmentLabel MplsLabel, mplsInSegmentNPop Integer32, mplsInSegmentAddrFamily AddressFamilyNumbers, mplsInSegmentXCIndex Integer32, Srinivasan et al. Expires October 2000 [Page 22] Internet Draft MPLS LSR MIB April 26, 2000 mplsInSegmentOwner MplsObjectOwner, mplsInSegmentTrafficParamPtr RowPointer, mplsInSegmentRowStatus RowStatus, mplsInSegmentStorageType StorageType, mplsInSegmentAdminStatus INTEGER, mplsInSegmentOperStatus INTEGER } mplsInSegmentIfIndex OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS not-accessible STATUS current DESCRIPTION "This is a unique index for an entry in the MplsInSegmentTable. This value represents the interface index for the incoming MPLS interface. A value of zero represents an incoming label from the per-platform label space. In this case, the mplsInSegmentLabel is interpreted to be an MPLS-type label." ::= { mplsInSegmentEntry 1 } mplsInSegmentLabel OBJECT-TYPE SYNTAX MplsLabel MAX-ACCESS not-accessible STATUS current DESCRIPTION "The incoming label for this segment." ::= { mplsInSegmentEntry 2 } mplsInSegmentNPop OBJECT-TYPE SYNTAX Integer32 (1..2147483647) MAX-ACCESS read-create STATUS current DESCRIPTION "The number of labels to pop from the incoming packet. Normally only the top label is popped from the packet and used for all switching decisions for that packet. Note that technologies which do not support label popping should set this value to its default value of 1." DEFVAL { 1 } ::= { mplsInSegmentEntry 3 } mplsInSegmentAddrFamily OBJECT-TYPE SYNTAX AddressFamilyNumbers MAX-ACCESS read-create STATUS current DESCRIPTION "The IANA address family [IANAFamily] of the incoming Srinivasan et al. Expires October 2000 [Page 23] Internet Draft MPLS LSR MIB April 26, 2000 packet. A value of other(0) indicates that the family type is either unknown or undefined." DEFVAL { other } ::= { mplsInSegmentEntry 4 } mplsInSegmentXCIndex OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "Index into mplsXCTable which identifies which cross- connect entry this segment is part of. A value of zero indicates that this entry is not referred to by any cross-connect entry. When a cross-connect entry is created which this in-segment is a part of, this object is automatically updated to reflect the value of mplsXCIndex of that cross-connect entry." DEFVAL { 0 } ::= { mplsInSegmentEntry 5 } mplsInSegmentOwner OBJECT-TYPE SYNTAX MplsObjectOwner MAX-ACCESS read-create STATUS current DESCRIPTION "Denotes the entity that created and is responsible for managing this segment." DEFVAL { unknown } ::= { mplsInSegmentEntry 6 } mplsInSegmentTrafficParamPtr OBJECT-TYPE SYNTAX RowPointer MAX-ACCESS read-create STATUS current DESCRIPTION "This variable represents a pointer to the traffic parameter specification for this in-segment. This value may point at an entry in the mplsTrafficParamTable to indicate which mplsTrafficParamEntry is to be assigned to this segment. This value may optionally point at an externally defined traffic parameter specification table. A value of zero-dot-zero indicates best-effort treatment. By having the same value of this object, two or more segments can indicate resource sharing." ::= { mplsInSegmentEntry 7 } mplsInSegmentRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create Srinivasan et al. Expires October 2000 [Page 24] Internet Draft MPLS LSR MIB April 26, 2000 STATUS current DESCRIPTION "This variable is used to create, modify, and/or delete a row in this table." ::= { mplsInSegmentEntry 8 } mplsInSegmentStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "This variable indicates the storage type for this object." ::= { mplsInSegmentEntry 9 } mplsInSegmentAdminStatus OBJECT-TYPE SYNTAX INTEGER { up(1), -- ready to pass packets down(2), testing(3) -- in some test mode } MAX-ACCESS read-create STATUS current DESCRIPTION "This value is used to represent the managerĘs desired operational status of this segment." ::= { mplsInSegmentEntry 10 } mplsInSegmentOperStatus OBJECT-TYPE SYNTAX INTEGER { up(1), -- ready to pass packets down(2), testing(3), -- in some test mode unknown(4), -- status cannot be determined for -- some reason dormant(5), notPresent(6), -- some component is missing lowerLayerDown(7) -- down due to the state of -- lower layer interfaces } MAX-ACCESS read-only STATUS current DESCRIPTION "This value represents the actual operational status of this segment." ::= { mplsInSegmentEntry 11 } -- End of mplsInSegmentTable Srinivasan et al. Expires October 2000 [Page 25] Internet Draft MPLS LSR MIB April 26, 2000 -- In-segment performance table. mplsInSegmentPerfTable OBJECT-TYPE SYNTAX SEQUENCE OF MplsInSegmentPerfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains statistical information for incoming MPLS segments to an LSR." ::= { mplsLsrObjects 4 } mplsInSegmentPerfEntry OBJECT-TYPE SYNTAX MplsInSegmentPerfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table contains statistical information about one incoming segment which was configured in the mplsInSegmentTable. The counters in this entry should behave in a manner similar to that of the interface." AUGMENTS { mplsInSegmentEntry } ::= { mplsInSegmentPerfTable 1 } MplsInSegmentPerfEntry ::= SEQUENCE { mplsInSegmentOctets Counter32, mplsInSegmentPackets Counter32, mplsInSegmentErrors Counter32, mplsInSegmentDiscards Counter32, -- high capacity counter mplsInSegmentHCOctets Counter64, mplsInSegmentPerfDiscontinuityTime TimeStamp } mplsInSegmentOctets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This value represents the total number of octets received by this segment." ::= { mplsInSegmentPerfEntry 1 } mplsInSegmentPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION Srinivasan et al. Expires October 2000 [Page 26] Internet Draft MPLS LSR MIB April 26, 2000 "Total number of packets received by this segment." ::= { mplsInSegmentPerfEntry 2 } mplsInSegmentErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of errored packets received on this segment." ::= { mplsInSegmentPerfEntry 3 } mplsInSegmentDiscards OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of labeled packets received on this in- segment, which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a labeled packet could be to free up buffer space." ::= { mplsInSegmentPerfEntry 4 } mplsInSegmentHCOctets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of octets received. This is the 64 bit version of mplsInSegmentOctets." ::= { mplsInSegmentPerfEntry 5 } mplsInSegmentPerfDiscontinuityTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime on the most recent occasion at which any one or more of this segment's Counter32 or Counter64 suffered a discontinuity. If no such discontinuities have occurred since the last re- initialization of the local management subsystem, then this object contains a zero value." ::= { mplsInSegmentPerfEntry 6 } -- End of mplsInSegmentPerfTable. Srinivasan et al. Expires October 2000 [Page 27] Internet Draft MPLS LSR MIB April 26, 2000 -- Out-segment table. mplsOutSegmentIndexNext OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the next appropriate value to be used for mplsOutSegmentIndex when creating entries in the mplsOutSegmentTable. If the number of unassigned entries is exhausted, this object will take on the value of 0. To obtain the mplsOutSegmentIndex value for a new entry, the manager must first issue a management protocol retrieval operation to obtain the current value of this object. The agent should modify the value to reflect the next unassigned index after each retrieval operation. After a manager retrieves a value the agent will determine through its local policy when this index value will be made available for reuse." ::= { mplsLsrObjects 5 } mplsOutSegmentTable OBJECT-TYPE SYNTAX SEQUENCE OF MplsOutSegmentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains a representation of the outgoing segments from an LSR." ::= { mplsLsrObjects 6 } mplsOutSegmentEntry OBJECT-TYPE SYNTAX MplsOutSegmentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table represents one outgoing segment. An entry can be created by a network administrator or an SNMP agent, or an MPLS signaling protocol. The object mplsOutSegmentOwner indicates the creator of this entry." INDEX { mplsOutSegmentIndex } ::= { mplsOutSegmentTable 1 } MplsOutSegmentEntry ::= SEQUENCE { mplsOutSegmentIndex Integer32, mplsOutSegmentIfIndex InterfaceIndex, Srinivasan et al. Expires October 2000 [Page 28] Internet Draft MPLS LSR MIB April 26, 2000 mplsOutSegmentPushTopLabel TruthValue, mplsOutSegmentTopLabel MplsLabel, mplsOutSegmentNextHopIpAddrType InetAddressType, mplsOutSegmentNextHopIpv4Addr InetAddressIPv4, mplsOutSegmentNextHopIpv6Addr InetAddressIPv6, mplsOutSegmentXCIndex Integer32, mplsOutSegmentOwner MplsObjectOwner, mplsOutSegmentTrafficParamPtr RowPointer, mplsOutSegmentRowStatus RowStatus, mplsOutSegmentStorageType StorageType, mplsOutSegmentAdminStatus INTEGER, mplsOutSegmentOperStatus INTEGER } mplsOutSegmentIndex OBJECT-TYPE SYNTAX Integer32(0..2147483647) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This value contains a unique index for this row. While a value of 0 is not valid as an index for this row it can be supplied as a valid value to index mplsXCTable to access entries for which no out- segment has been configured." ::= { mplsOutSegmentEntry 1 } mplsOutSegmentIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-create STATUS current DESCRIPTION "This value contains the interface index of the outgoing interface." ::= { mplsOutSegmentEntry 2 } mplsOutSegmentPushTopLabel OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "This value indicates whether or not a top label should be pushed onto the outgoing packet's label stack. The value of this variable must be set to true if the outgoing interface does not support pop- and-go (for example an ATM interface) or if it is a tunnel origination. Note that it is considered an error in the case that mplsOutSegmentPushTopLabel is set to false, but the cross-connect entry which refers to this out-segment has a non-zero mplsLabelStackIndex. The LSR MUST ensure that this Srinivasan et al. Expires October 2000 [Page 29] Internet Draft MPLS LSR MIB April 26, 2000 situation does not happen " ::= { mplsOutSegmentEntry 3 } mplsOutSegmentTopLabel OBJECT-TYPE SYNTAX MplsLabel MAX-ACCESS read-create STATUS current DESCRIPTION "If mplsOutSegmentPushTopLabel is true then this represents the label that should be pushed onto the top of the outgoing packet's label stack." ::= { mplsOutSegmentEntry 4 } mplsOutSegmentNextHopIpAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates whether the next hop address is IPv4 or IPv6. Note that a value of unknown (0) is valid only when the outgoing interface is of type point-to- point." DEFVAL { unknown } ::= { mplsOutSegmentEntry 5 } mplsOutSegmentNextHopIpv4Addr OBJECT-TYPE SYNTAX InetAddressIPv4 MAX-ACCESS read-create STATUS current DESCRIPTION "IPv4 Address of the next hop. Its value is significant only when mplsOutSegmentNextHopIpAddrType is ipV4 (1), otherwise it should return a value of 0." ::= { mplsOutSegmentEntry 6 } mplsOutSegmentNextHopIpv6Addr OBJECT-TYPE SYNTAX InetAddressIPv6 MAX-ACCESS read-create STATUS current DESCRIPTION "IPv6 address of the next hop. Its value is significant only when mplsOutSegmentNextHopIpAddrType is ipV6 (2), otherwise it should return a value of 0." ::= { mplsOutSegmentEntry 7 } mplsOutSegmentXCIndex OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only Srinivasan et al. Expires October 2000 [Page 30] Internet Draft MPLS LSR MIB April 26, 2000 STATUS current DESCRIPTION "Index into mplsXCTable which identifies which cross- connect entry this segment is part of. A value of zero indicates that this entry is not referred to by any cross-connect entry. When a cross-connect entry is created which this out-segment is a part of, this object is automatically updated to reflect the value of mplsXCIndex of that cross-connect entry." DEFVAL { 0 } ::= { mplsOutSegmentEntry 8 } mplsOutSegmentOwner OBJECT-TYPE SYNTAX MplsObjectOwner MAX-ACCESS read-create STATUS current DESCRIPTION "Denotes the entity which created and is responsible for managing this segment." DEFVAL { unknown } ::= { mplsOutSegmentEntry 9 } mplsOutSegmentTrafficParamPtr OBJECT-TYPE SYNTAX RowPointer MAX-ACCESS read-create STATUS current DESCRIPTION "This variable represents a pointer to the traffic parameter specification for this out-segment. This value may point at an entry in the mplsTrafficParamTable to indicate which mplsTrafficParamEntry is to be assigned to this segment. This value may optionally point at an externally defined traffic parameter specification table. A value of zero-dot-zero indicates best- effort treatment. By having the same value of this object, two or more segments can indicate resource sharing." ::= { mplsOutSegmentEntry 10 } mplsOutSegmentRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "For creating, modifying, and deleting this row." ::= { mplsOutSegmentEntry 11 } mplsOutSegmentStorageType OBJECT-TYPE SYNTAX StorageType Srinivasan et al. Expires October 2000 [Page 31] Internet Draft MPLS LSR MIB April 26, 2000 MAX-ACCESS read-create STATUS current DESCRIPTION "This variable indicates the storage type for this object." ::= { mplsOutSegmentEntry 12 } mplsOutSegmentAdminStatus OBJECT-TYPE SYNTAX INTEGER { up(1), -- ready to pass packets down(2), testing(3) -- in some test mode } MAX-ACCESS read-create STATUS current DESCRIPTION "The desired operational status of this segment." ::= { mplsOutSegmentEntry 13 } mplsOutSegmentOperStatus OBJECT-TYPE SYNTAX INTEGER { up(1), -- ready to pass packets down(2), testing(3), -- in some test mode unknown(4), -- status cannot be determined -- for some reason dormant(5), notPresent(6), -- some component is missing lowerLayerDown(7) -- down due to the state -- of lower layer interfaces } MAX-ACCESS read-only STATUS current DESCRIPTION "The actual operational status of this segment." ::= { mplsOutSegmentEntry 14 } -- End of mplsOutSegmentTable -- Out-segment performance table. mplsOutSegmentPerfTable OBJECT-TYPE SYNTAX SEQUENCE OF MplsOutSegmentPerfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains statistical information about outgoing segments from an LSR. The counters in this entry should behave in a manner similar to that of Srinivasan et al. Expires October 2000 [Page 32] Internet Draft MPLS LSR MIB April 26, 2000 the interface." ::= { mplsLsrObjects 7 } mplsOutSegmentPerfEntry OBJECT-TYPE SYNTAX MplsOutSegmentPerfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table contains statistical information about one outgoing segment configured in mplsOutSegmentTable." AUGMENTS { mplsOutSegmentEntry } ::= { mplsOutSegmentPerfTable 1 } MplsOutSegmentPerfEntry ::= SEQUENCE { mplsOutSegmentOctets Counter32, mplsOutSegmentPackets Counter32, mplsOutSegmentErrors Counter32, mplsOutSegmentDiscards Counter32, -- HC counter mplsOutSegmentHCOctets Counter64, mplsOutSegmentPerfDiscontinuityTime TimeStamp } mplsOutSegmentOctets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This value contains the total number of octets sent on this segment." ::= { mplsOutSegmentPerfEntry 1 } mplsOutSegmentPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This value contains the total number of packets sent on this segment." ::= { mplsOutSegmentPerfEntry 2 } mplsOutSegmentErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets that could not be sent due to Srinivasan et al. Expires October 2000 [Page 33] Internet Draft MPLS LSR MIB April 26, 2000 errors on this segment." ::= { mplsOutSegmentPerfEntry 3 } mplsOutSegmentDiscards OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of labeled packets received on this out- segment, which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a labeled packet could be to free up buffer space." ::= { mplsOutSegmentPerfEntry 4 } mplsOutSegmentHCOctets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of octets sent. This is the 64 bit version of mplsOutSegmentOctets." ::= { mplsOutSegmentPerfEntry 5 } mplsOutSegmentPerfDiscontinuityTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime on the most recent occasion at which any one or more of this segment's Counter32 or Counter64 suffered a discontinuity. If no such discontinuities have occurred since the last re- initialization of the local management subsystem, then this object contains a zero value." ::= { mplsOutSegmentPerfEntry 6 } -- End of mplsOutSegmentPerfTable. -- Cross-connect table. mplsXCIndexNext OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains an appropriate value to be used for mplsXCIndex when creating entries in the Srinivasan et al. Expires October 2000 [Page 34] Internet Draft MPLS LSR MIB April 26, 2000 mplsXCTable. The value 0 indicates that no unassigned entries are available. To obtain the value of mplsXCIndex for a new entry in the mplsXCTable, the manager issues a management protocol retrieval operation to obtain the current value of mplsXCIndex. After each retrieval operation, the agent should modify the value to reflect the next unassigned index. After a manager retrieves a value the agent will determine through its local policy when this index value will be made available for reuse." ::= { mplsLsrObjects 8 } mplsXCTable OBJECT-TYPE SYNTAX SEQUENCE OF MplsXCEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table specifies information for switching between LSP segments. It supports point-to-point, point-to-multipoint and multipoint-to-point connections. mplsLabelStackTable specifies the label stack information for a cross-connect LSR and is referred to from mplsXCTable." ::= { mplsLsrObjects 9 } mplsXCEntry OBJECT-TYPE SYNTAX MplsXCEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in this table represents one cross-connect entry. The following objects index it: - cross-connect index mplsXCIndex that uniquely identifies a group of cross-connect entries - interface index of the in-segment, mplsInSegmentIfIndex - incoming label(s), mplsInSegmentLabel - out-segment index, mplsOutSegmentIndex Originating LSPs: These are represented by using the special combination of values mplsInSegmentIfIndex=0 and mplsInSegmentLabel=0 as indexes. In this case the mplsOutSegmentIndex MUST be non-zero. Terminating LSPs: These are represented by using the special value mplsOutSegmentIndex=0 as index. Srinivasan et al. Expires October 2000 [Page 35] Internet Draft MPLS LSR MIB April 26, 2000 Special labels: Entries indexed by reserved MPLS label values 0 through 15 imply terminating LSPs and MUST have mplsOutSegmentIfIndex = 0. Note that situations where LSPs are terminated with incoming label equal to 0, should have mplsInSegmentIfIndex = 0 as well, but can be distinguished from originating LSPs because the mplsOutSegmentIfIndex = 0. The mplsOutSegmentIfIndex MUST only be set to 0 in cases of terminating LSPs. An entry can be created by a network administrator or by an SNMP agent as instructed by an MPLS signaling protocol." INDEX { mplsXCIndex, mplsInSegmentIfIndex, mplsInSegmentLabel, mplsOutSegmentIndex } ::= { mplsXCTable 1 } MplsXCEntry ::= SEQUENCE { mplsXCIndex Integer32, mplsXCLspId MplsLSPID, mplsXCLabelStackIndex Integer32, mplsXCIsPersistent TruthValue, mplsXCOwner MplsObjectOwner, mplsXCRowStatus RowStatus, mplsXCStorageType StorageType, mplsXCAdminStatus INTEGER, mplsXCOperStatus INTEGER } mplsXCIndex OBJECT-TYPE SYNTAX Integer32 (1..2147483647) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Primary index for the row identifying a group of cross-connect segments." ::= { mplsXCEntry 1 } mplsXCLspId OBJECT-TYPE SYNTAX MplsLSPID MAX-ACCESS read-create STATUS current DESCRIPTION "This value identifies the label switched path that this cross-connect entry belongs to." ::= { mplsXCEntry 2 } Srinivasan et al. Expires October 2000 [Page 36] Internet Draft MPLS LSR MIB April 26, 2000 mplsXCLabelStackIndex OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-create STATUS current DESCRIPTION "Primary index into mplsLabelStackTable identifying a stack of labels to be pushed beneath the top label. Note that the top label identified by the out- segment ensures that all the components of a multipoint-to-point connection have the same outgoing label. A value of 0 indicates that no labels are to be stacked beneath the top label." ::= { mplsXCEntry 3 } mplsXCIsPersistent OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Denotes whether or not this cross-connect entry and associated in- and out-segments should be restored automatically after failures. This value MUST be set to false in cases where this cross-connect entry was created by a signaling protocol." DEFVAL { false } ::= { mplsXCEntry 4 } mplsXCOwner OBJECT-TYPE SYNTAX MplsObjectOwner MAX-ACCESS read-create STATUS current DESCRIPTION "Denotes the entity that created and is responsible for managing this cross-connect." ::= { mplsXCEntry 5 } mplsXCRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "For creating, modifying, and deleting this row." ::= { mplsXCEntry 6 } mplsXCStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "Defines the storage type for this object." Srinivasan et al. Expires October 2000 [Page 37] Internet Draft MPLS LSR MIB April 26, 2000 ::= { mplsXCEntry 7 } mplsXCAdminStatus OBJECT-TYPE SYNTAX INTEGER { up(1), -- ready to pass packets down(2), testing(3) -- in some test mode } MAX-ACCESS read-create STATUS current DESCRIPTION "The desired operational status of this segment." ::= { mplsXCEntry 8 } mplsXCOperStatus OBJECT-TYPE SYNTAX INTEGER { up(1), -- ready to pass packets down(2), testing(3), -- in some test mode unknown(4), -- status cannot be determined -- for some reason. dormant(5), notPresent(6), -- some component is missing lowerLayerDown(7) -- down due to the state of -- lower layer interfaces } MAX-ACCESS read-only STATUS current DESCRIPTION "The actual operational status of this cross- connect." ::= { mplsXCEntry 9 } -- End of mplsXCTable -- Label stack table. mplsMaxLabelStackDepth OBJECT-TYPE SYNTAX Integer32 (1..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum stack depth supported by this LSR." ::= { mplsLsrObjects 10 } mplsLabelStackIndexNext OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION Srinivasan et al. Expires October 2000 [Page 38] Internet Draft MPLS LSR MIB April 26, 2000 "This object contains an appropriate value to be used for mplsLabelStackIndex when creating entries in the mplsLabelStackTable. The value 0 indicates that no unassigned entries are available. To obtain an mplsLabelStackIndex value for a new entry, the manager issues a management protocol retrieval operation to obtain the current value of this object. After each retrieval operation, the agent should modify the value to reflect the next unassigned index. After a manager retrieves a value the agent will determine through its local policy when this index value will be made available for reuse." ::= { mplsLsrObjects 11 } mplsLabelStackTable OBJECT-TYPE SYNTAX SEQUENCE OF MplsLabelStackEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table specifies the label stack to be pushed onto a packet, beneath the top label. Entries into this table are referred to from mplsXCTable." ::= { mplsLsrObjects 12 } mplsLabelStackEntry OBJECT-TYPE SYNTAX MplsLabelStackEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table represents one label which is to be pushed onto an outgoing packet, beneath the top label. An entry can be created by a network administrator or by an SNMP agent as instructed by an MPLS signaling protocol." INDEX { mplsLabelStackIndex, mplsLabelStackLabelIndex } ::= { mplsLabelStackTable 1 } MplsLabelStackEntry ::= SEQUENCE { mplsLabelStackIndex Integer32, mplsLabelStackLabelIndex Integer32, mplsLabelStackLabel MplsLabel, mplsLabelStackRowStatus RowStatus, mplsLabelStackStorageType StorageType } mplsLabelStackIndex OBJECT-TYPE SYNTAX Integer32 (1..2147483647) MAX-ACCESS not-accessible STATUS current Srinivasan et al. Expires October 2000 [Page 39] Internet Draft MPLS LSR MIB April 26, 2000 DESCRIPTION "Primary index for this row identifying a stack of labels to be pushed on an outgoing packet, beneath the top label." ::= { mplsLabelStackEntry 1 } mplsLabelStackLabelIndex OBJECT-TYPE SYNTAX Integer32 (1..2147483647) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Secondary index for this row identifying one label of the stack. Note that an entry with a smaller mplsLabelStackLabelIndex would refer to a label higher up the label stack and would be popped at a downstream LSR before a label represented by a higher mplsLabelStackLabelIndex at a downstream LSR." ::= { mplsLabelStackEntry 2 } mplsLabelStackLabel OBJECT-TYPE SYNTAX MplsLabel MAX-ACCESS read-create STATUS current DESCRIPTION "The label to pushed." ::= { mplsLabelStackEntry 3 } mplsLabelStackRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "For creating, modifying, and deleting this row." ::= { mplsLabelStackEntry 4 } mplsLabelStackStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "Defines the storage type for this object." ::= { mplsLabelStackEntry 5 } -- End of mplsLabelStackTable -- Traffic Parameter table. mplsTrafficParamIndexNext OBJECT-TYPE SYNTAX Integer32 (0..2147483647) Srinivasan et al. Expires October 2000 [Page 40] Internet Draft MPLS LSR MIB April 26, 2000 MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains an appropriate value which will be used for mplsTrafficParamIndex when creating entries in the mplsTrafficParamTable. The value 0 indicates that no unassigned entries are available. To obtain the mplsTrafficParamIndex value for a new entry, the manager issues a management protocol retrieval operation to obtain the current value of this object. After each retrieval operation, the agent should modify the value to reflect the next unassigned index. After a manager retrieves a value the agent will determine through its local policy when this index value will be made available for reuse." ::= { mplsLsrObjects 13 } mplsTrafficParamTable OBJECT-TYPE SYNTAX SEQUENCE OF MplsTrafficParamEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table specifies the Traffic Parameter objects for in and out-segments." ::= { mplsLsrObjects 14 } mplsTrafficParamEntry OBJECT-TYPE SYNTAX MplsTrafficParamEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table represents the TrafficParam objects for one or more in or out segments. A single entry can be pointed to by multiple segments indicating resource sharing." INDEX { mplsTrafficParamIndex } ::= { mplsTrafficParamTable 1 } MplsTrafficParamEntry ::= SEQUENCE { mplsTrafficParamIndex Integer32, mplsTrafficParamMaxRate MplsBitRate, mplsTrafficParamMeanRate MplsBitRate, mplsTrafficParamMaxBurstSize MplsBurstSize, mplsTrafficParamRowStatus RowStatus, mplsTrafficParamStorageType StorageType } mplsTrafficParamIndex OBJECT-TYPE SYNTAX Integer32 (1..2147483647) Srinivasan et al. Expires October 2000 [Page 41] Internet Draft MPLS LSR MIB April 26, 2000 MAX-ACCESS not-accessible STATUS current DESCRIPTION "Uniquely identifies this row of the table. Note that zero represents an invalid index." ::= { mplsTrafficParamEntry 1 } mplsTrafficParamMaxRate OBJECT-TYPE SYNTAX MplsBitRate UNITS "kilobits per second" MAX-ACCESS read-create STATUS current DESCRIPTION "Maximum rate in kilobits/second." ::= { mplsTrafficParamEntry 4 } mplsTrafficParamMeanRate OBJECT-TYPE SYNTAX MplsBitRate UNITS "kilobits per second" MAX-ACCESS read-create STATUS current DESCRIPTION "Mean rate in kilobits/second." ::= { mplsTrafficParamEntry 5 } mplsTrafficParamMaxBurstSize OBJECT-TYPE SYNTAX MplsBurstSize UNITS "bytes" MAX-ACCESS read-create STATUS current DESCRIPTION "Maximum burst size in bytes." ::= { mplsTrafficParamEntry 6 } mplsTrafficParamRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "For creating, modifying, and deleting this row." ::= { mplsTrafficParamEntry 7 } mplsTrafficParamStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "The storage type for this object." ::= { mplsTrafficParamEntry 8 } Srinivasan et al. Expires October 2000 [Page 42] Internet Draft MPLS LSR MIB April 26, 2000 -- End of mplsTrafficParamTable -- Notification Configuration mplsInSegmentTrapEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "If this object is true, then it enables the generation of mplsInSegmentUp and mplsInSegmentDown traps, otherwise these traps are not emitted." DEFVAL { false } ::= { mplsLsrObjects 15 } mplsOutSegmentTrapEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "If this object is true, then it enables the generation of mplsOutSegmentUp and mplsOutSegmentDown traps, otherwise these traps are not emitted." DEFVAL { false } ::= { mplsLsrObjects 16 } mplsXCTrapEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "If this object is true, then it enables the generation of mplsXCUp and mplsXCDown traps, otherwise these traps are not emitted." DEFVAL { false } ::= { mplsLsrObjects 17 } -- Interface -- In-segment. mplsInSegmentUp NOTIFICATION-TYPE OBJECTS { mplsInSegmentIfIndex, mplsInSegmentLabel, mplsInSegmentAdminStatus, mplsInSegmentOperStatus } STATUS current DESCRIPTION Srinivasan et al. Expires October 2000 [Page 43] Internet Draft MPLS LSR MIB April 26, 2000 "This notification is generated when a mplsInSegmentOperStatus object for one of the configured in-segments is about to leave the down state and transition into some other state (but not into the notPresent state). This other state is indicated by the included value of mplsInSegmentOperStatus." ::= { mplsLsrNotifications 1 } mplsInSegmentDown NOTIFICATION-TYPE OBJECTS { mplsInSegmentIfIndex, mplsInSegmentLabel, mplsInSegmentAdminStatus, mplsInSegmentOperStatus } STATUS current DESCRIPTION "This notification is generated when a mplsInSegmentOperStatus object for one of the configured in-segments is about to enter the down state from some other state (but not from the notPresent state). This other state is indicated by the included value of mplsInSegmentOperStatus." ::= { mplsLsrNotifications 2 } -- Out-segment. mplsOutSegmentUp NOTIFICATION-TYPE OBJECTS { mplsOutSegmentIndex, mplsInSegmentAdminStatus, mplsInSegmentOperStatus } STATUS current DESCRIPTION "This notification is generated when a mplsOutSegmentOperStatus object for one of the configured out-segments is about to leave the down state and transition into some other state (but not into the notPresent state). This other state is indicated by the included value of mplsOutSegmentOperStatus." ::= { mplsLsrNotifications 3 } mplsOutSegmentDown NOTIFICATION-TYPE OBJECTS { mplsOutSegmentIndex, mplsInSegmentAdminStatus, mplsInSegmentOperStatus } STATUS current DESCRIPTION "This notification is generated when a mplsOutSegmentOperStatus object for one of the configured out-segments is about to enter the down Srinivasan et al. Expires October 2000 [Page 44] Internet Draft MPLS LSR MIB April 26, 2000 state from some other state (but not from the notPresent state). This other state is indicated by the included value of mplsOutSegmentOperStatus." ::= { mplsLsrNotifications 4 } -- Cross-connect. mplsXCUp NOTIFICATION-TYPE OBJECTS { mplsXCIndex, mplsInSegmentIfIndex, mplsInSegmentLabel, mplsOutSegmentIndex, mplsXCAdminStatus, mplsXCOperStatus } STATUS current DESCRIPTION "This notification is generated when a mplsXCOperStatus object for one of the configured cross-connect entries is about to leave the down state and transition into some other state (but not into the notPresent state). This other state is indicated by the included value of mplsXCOperStatus." ::= { mplsLsrNotifications 5 } mplsXCDown NOTIFICATION-TYPE OBJECTS { mplsXCIndex, mplsInSegmentIfIndex, mplsInSegmentLabel, mplsOutSegmentIndex, mplsXCAdminStatus, mplsXCOperStatus } STATUS current DESCRIPTION "This notification is generated when a mplsXCOperStatus object for one of the configured cross-connect entries is about to enter the down state from some other state (but not from the notPresent state). This other state is indicated by the included value of mplsXCOperStatus." ::= { mplsLsrNotifications 6 } -- End of notifications. -- Module compliance. mplsLsrGroups OBJECT IDENTIFIER ::= { mplsLsrConformance 1 } Srinivasan et al. Expires October 2000 [Page 45] Internet Draft MPLS LSR MIB April 26, 2000 mplsLsrCompliances OBJECT IDENTIFIER ::= { mplsLsrConformance 2 } mplsLsrModuleCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "Compliance statement for agents that support the MPLS LSR MIB." MODULE -- this module -- The mandatory groups have to be implemented -- by all LSRs. However, they may all be supported -- as read-only objects in the case where manual -- configuration is unsupported. MANDATORY-GROUPS { mplsInSegmentGroup, mplsOutSegmentGroup, mplsXCGroup, mplsInterfaceGroup, mplsPerfGroup, mplsSegmentDiscontinuityGroup } GROUP mplsHCInSegmentPerfGroup DESCRIPTION "This group is mandatory for those in-segment entries for which the object mplsInSegmentOutOctets wraps around too quickly." GROUP mplsHCOutSegmentPerfGroup DESCRIPTION "This group is mandatory for those out-segment entries for which the object mplsOutSegmentOctets wraps around too quickly." GROUP mplsTrafficParamGroup DESCRIPTION "This group is mandatory for those LSRs that support QoS resource reservation." -- Depending on whether the device implements -- persistent cross-connects or not one of the -- following two groups is mandatory. GROUP mplsXCIsPersistentGroup DESCRIPTION "This group is mandatory for devices which support persistent cross-connects. The following constraints apply: mplsXCIsPersistent must at least be read-only returning true(2)." Srinivasan et al. Expires October 2000 [Page 46] Internet Draft MPLS LSR MIB April 26, 2000 GROUP mplsXCIsNotPersistentGroup DESCRIPTION "This group is mandatory for devices which support non-persistent cross-connects. The following constraints apply: mplsXCIsPersistent must at least be read-only returning false(1)." -- mplsInterfaceConfTable OBJECT mplsInterfaceConfStorageType SYNTAX INTEGER { other(1) } MIN-ACCESS read-only DESCRIPTION "Only other(1) needs to be supported." -- mplsInSegmentTable OBJECT mplsInSegmentXCIndex DESCRIPTION "Write access is not required." OBJECT mplsInSegmentNPop MIN-ACCESS read-only DESCRIPTION "Write access if not required. This object should be set to 1 if it is read-only." OBJECT mplsInSegmentAddrFamily DESCRIPTION "Write access is not required. Adraft-ietf-mpls-arch-06.txt>, August 1999. [MPLSFW] Callon, R., Doolan, P., Feldman, N., Fredette, A., Swallow, G., and A. Viswanathan, "A Framework for Multiprotocol Label Switching", Internet Draft <draft-ietf-mpls-framework-05.txt>, September 1999. [LblStk] Rosen, E., Rekhter, Y., Tappan, D., Farinacci, D., Federokow, G., Li, T., and A. Conta, "MPLS Label Stack Encoding", Internet Draft , September 1999. [Assigned] Reynolds, J., and J. Postel, "Assigned Numbers", RFC 1700, October 1994. See also: http://www.isi.edu/in-notes/iana/assignments/smi- numbers [IANAFamily] Internet Assigned Numbers Authority (IANA), ADDRESS FAMILY NUMBERS,(http://www.isi.edu/in- notes/iana/assignements/address-family-numbers), for MIB see: ftp://ftp.isi.edu/mib/ianaaddressfamilynumbers.mib [SNMPArch] Harrington, D., Presuhn, R., and B. Wijnen, "An Architecture for Describing SNMP Management Frameworks", RFC 2271, January 1998. [SMIv1] Rose, M., and K. McCloghrie, "Structure and Identification of Management Information for TCP/IP- based Internets", RFC 1155, May 1990. [SNMPv1MIBDef]Rose, M., and K. McCloghrie, "Concise MIB Definitions", RFC 1212, March 1991. [SNMPv1Traps] M. Rose, "A Convention for Defining Traps for use with the SNMP", RFC 1215, March 1991. [RFC2572] Case, J., Harrington D., Presuhn R., and B. Wijnen, "Message Processing and Dispatching for the Simple Network Management Protocol (SNMP)", RFC 2572, April 1999. Srinivasan et al. Expires October 2000 [Page 55] Internet Draft MPLS LSR MIB April 26, 2000 [RFC2574] Blumenthal, U., and B. Wijnen, "User-based Security Model (USM) for version 3 of the Simple Network Management Protocol (SNMPv3)", RFC 2574, April 1999. [RFC1905] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Protocol Operations for Version 2 of the Simple Network Management Protocol (SNMPv2)", RFC 1905, January 1996. [RFC2573] Levi, D., Meyer, P., and B. Stewart, "SNMPv3 Applications", RFC 2573, April 1999. [RFC2575] Wijnen, B., Presuhn, R., and K. McCloghrie, "View- based Access Control Model (VACM) for the Simple Network Management Protocol (SNMP)", RFC 2575, April 1999. [RFC2570] Case, J., Mundy, R., Partain, D., and B. Stewart, "Introduction to Version 3 of the Internet-standard Network Management Framework", RFC 2570, April 1999. [SMIv2] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Structure of Management Information for Version 2 of the Simple Network Management Protocol (SNMPv2)", RFC 1902, January 1996. [SNMPv2TC] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Textual Conventions for Version 2 of the Simple Network Management Protocol (SNMPv2)", RFC 1903, SNMP Research, Inc., Cisco Systems, Inc., January 1996. [SNMPv2Conf] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Conformance Statements for Version 2 of the Simple Network Management Protocol (SNMPv2)", RFC 1904, January 1996. [SNMPv1] Case, J., Fedor, M., Schoffstall, M., and J. Davin, "Simple Network Management Protocol", RFC 1157, May 1990. [SNMPv2c] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Introduction to Community-based SNMPv2", RFC 1901, January 1996. [SNMPv2TM] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Transport Mappings for Version 2 of the Simple Network Management Protocol (SNMPv2)", Srinivasan et al. Expires October 2000 [Page 56] Internet Draft MPLS LSR MIB April 26, 2000 RFC 1906, January 1996. [SNMPv3MP] Case, J., Harrington D., Presuhn R., and B. Wijnen, "Message Processing and Dispatching for the Simple Network Management Protocol (SNMP)", RFC 2272, January 1998. [SNMPv3USM] Blumenthal, U., and B. Wijnen, "User-based Security Model (USM) for version 3 of the Simple Network Management Protocol (SNMPv3)", RFC 2574, April 1999. [SNMPv2PO] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Protocol Operations for Version 2 of the Simple Network Management Protocol (SNMPv2)", RFC 1905, January 1996. [SNMPv3App] Levi, D., Meyer, P., and B. Stewart, "SNMPv3 Applications", RFC 2273, January 1998. [SNMPv3VACM] Wijnen, B., Presuhn, R., and K. McCloghrie, "View- based Access Control Model (VACM) for the Simple Network Management Protocol (SNMP)", RFC 2575, April 1999. [IPSEC] Kent, S., and Atkinson, R., "Security Architecture for the Internet Protocol", RFC 2401, November 1998. [IFMIB] McCloghrie, K., and F. Kastenholtz, "The Interfaces Group MIB using SMIv2", RFC 2233, Nov. 1997 [ATOMMIB] Tesink, K., "Definitions of Managed Objects for ATM Management", RFC 2515, Feb. 1999 [BCP14] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. 15. Authors' Addresses Cheenu Srinivasan Tachion Networks, Inc. Monmouth Park Corporate Center I Building C, 185 Monmouth Parkway West Long Branch, NJ 07764 Phone: +1-732-542-7750 x1234 Email: cheenu@tachion.com Arun Viswanathan Srinivasan et al. Expires October 2000 [Page 57] Internet Draft MPLS LSR MIB April 26, 2000 Force10 Networks, Inc. 1440 McCarthy Blvd Milpitas, CA 95035 Phone: +1-408-571-3516 Email: arun@force10networks.com Thomas D. Nadeau Cisco Systems, Inc. 250 Apollo Drive Chelmsford, MA 01824 Phone: +1-978-244-3051 Email: tnadeau@cisco.com 16. Full Copyright Statement Copyright (C) The Internet Society (2000). All Rights Reserved. This document and translations of it may be copied and furnished to others, and derivative works that comment on or otherwise explain it or assist in its implementation may be prepared, copied, published and distributed, in whole or in part, without restriction of any kind, provided that the above copyright notice and this paragraph are included on all such copies and derivative works. However, this document itself may not be modified in any way, such as by removing the copyright notice or references to the Internet Society or other Internet organizations, except as needed for the purpose of developing Internet standards in which case the procedures for copyrights defined in the Internet Standards process must be followed, or as required to translate it into languages other than English. The limited permissions granted above are perpetual and will not be revoked by the Internet Society or its successors or assigns. This document and the information contained herein is provided on an "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Srinivasan et al. Expires October 2000 [Page 58]