Internet Draft
Network Working Group Jeffrey Mogul, Compaq WRL
Internet-Draft David Mills, UDel
Expires: 17 February 2000 Jan Brittenson, Sun
Jonathan Stone, Stanford
Ulrich Windl, Universitaet Regensburg
17 August 1999
Pulse-Per-Second API for UNIX-like Operating Systems, Version 1.0
draft-mogul-pps-api-05.txt
STATUS OF THIS MEMO
This document is an Internet-Draft and is in full
conformance with all provisions of Section 10 of RFC2026.
Internet-Drafts are working documents of the Internet
Engineering Task Force (IETF), its areas, and its working
groups. Note that other groups may also distribute working
documents as Internet-Drafts.
Internet-Drafts are draft documents valid for a maximum of
six months and may be updated, replaced, or obsoleted by
other documents at any time. It is inappropriate to use
Internet-Drafts as reference material or to cite them other
than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt
The list of Internet-Draft Shadow Directories can be
accessed at http://www.ietf.org/shadow.html.
Distribution of this document is unlimited. Please send
comments to the authors.
ABSTRACT
RFC1589 describes a UNIX kernel implementation model for
high-precision time-keeping. This model is meant for use
in conjunction with the Network Time Protocol (NTP,
RFC1305), or similar time synchronization protocols. One
aspect of this model is an accurate interface to the
high-accuracy, one pulse-per-second (PPS) output typically
available from precise time sources (such as a GPS or GOES
receiver). RFC1589 did not define an API for managing the
PPS facility, leaving implementors without a portable means
for using PPS sources. This document specifies such an
API.
Mogul, Mills, Brittenson, Stone, Windl [Page 1]
Internet-Draft Pulse-Per-Second API 17 August 1999 11:18
TABLE OF CONTENTS
1 Introduction 2
2 Data types for representing timestamps 4
2.1 Resolution 4
2.2 Time scale 4
3 API 5
3.1 PPS abstraction 5
3.2 New data structures 6
3.3 Mode bit definitions 9
3.4 New functions 12
3.4.1 New functions: obtaining PPS sources 13
3.4.2 New functions: setting PPS parameters 15
3.4.3 New functions: access to PPS timestamps 17
3.4.4 New functions: disciplining the kernel timebase 19
3.5 Compliance rules 22
3.5.1 Functions 22
3.5.2 Mode bits 22
3.6 Examples 23
4 Security Considerations 25
5 Acknowledgements 25
6 References 26
7 Authors' addresses 26
A. Extensions and related APIs 27
A.1 Extension: Parameters for the ``echo'' mechanism 27
A.2 Extension: Obtaining information about external clocks 27
A.3 Extension: Finding a PPS source 28
B. Example implementation: PPSDISC Line discipline 29
B.1 Example 29
C. Available implementations 30
1 Introduction
RFC1589 [4] describes a model and programming interface for generic
operating system software that manages the system clock and timer
functions. The model provides improved accuracy and stability for
most workstations and servers using the Network Time Protocol
(NTP) [3] or similar time synchronization protocol. The model
supports the use of external timing sources, such as the precision
pulse-per-second (PPS) signals typically available from precise time
sources (such as a GPS or GOES receiver).
However, RFC1589 did not define an application programming interface
(API) for the PPS facility. This document specifies such an
interface, for use with UNIX (or UNIX-like) operating systems. Such
systems often conform to the ``Single UNIX Specification'' [5],
sometimes known as POSIX.
Mogul, Mills, Brittenson, Stone, Windl [Page 2]
Internet-Draft Pulse-Per-Second API 17 August 1999 11:18
One convenient means to provide a PPS signal to a computer system is
to connect that signal to a modem-control pin on a serial-line
interface to the computer. The Data Carrier Detect (DCD) pin is
frequently used for this purpose. Typically, the time-code output of
the time source is transmitted to the computer over the same serial
line. The computer detects a signal transition on the DCD pin,
usually by receiving an interrupt, and records a timestamp as soon as
possible.
Although existing practice has focussed on the use of serial lines
and DCD transitions, PPS signals might also be delivered by other
kinds of devices. The API specified in this document does not
require the use of a serial line, although it may be somewhat biased
in that direction.
The typical use of this facility is for the operating system to
record a high-resolution timestamp as soon as possible after it
detects a PPS signal transition (usually indicated by an interrupt).
This timestamp can then be made available, with less stringent delay
constraints, to timekeeping software. The software can compare the
captured timestamp to the received time-code to accurately discover
the absolute offset between the system clock and the precise time
source.
The operating system may also deliver the PPS event to a kernel
procedure, called the ``in-kernel PPS consumer.'' One example would
be the ``hardpps()'' procedure, described in RFC1589, which is used
to discipline the kernel's internal timebase.
The API specified in this document allows for one or more signal
sources attached to a computer system to provide PPS inputs, at the
option of user-level software. User-level software may obtain
signal-transition timestamps for any of these PPS sources.
User-level software may optionally specify at most one of these PPS
sources to be used to discipline the system's internal timebase.
Although the primary purpose of this API is for capturing true
pulse-per-second events, the API may also be used for accurately
timestamping events of other periods, or even aperiodic events, when
these can be expressed as signal transitions.
This document does not define internal details of how the API must be
implemented, and does not specify constraints on the accuracy,
resolution, or latency of the PPS feature. However, the utility of
this feature is inversely proportional to the delay (and variance of
delay), and implementors are encouraged to take this seriously.
In principle, the rate of events to be captured, or the frequency of
the signals, can range from once per day (or less often) to several
thousand per second. However, since in most implementations the
timestamping function will be implemented as a processor interrupt at
Mogul, Mills, Brittenson, Stone, Windl [Page 3]
Internet-Draft Pulse-Per-Second API 17 August 1999 11:18
a relatively high priority, it is prudent to limit the rate of such
events. This may be done either by mechanisms in the hardware that
generates the signals, or by the operating system.
2 Data types for representing timestamps
Computer systems use various representations of time. Because this
API is concerned with the provision of high-accuracy, high-resolution
time information, the choice of representation is significant. (Here
we consider only binary representations, not human-format
representations.)
The two interesting questions are:
1. what is the resolution of the representation?
2. what time scale is represented?
These questions often lead to contentious arguments. Since this API
is intended for use with NTP and POSIX-compliant systems, however, we
can limit the choices to representations compatible with existing NTP
and POSIX practice, even if that practice is considered ``wrong'' in
some quarters.
2.1 Resolution
In the NTP protocol, ``timestamps are represented as a 64-bit
unsigned fixed-point number, in seconds relative to 0h on 1 January
1900. The integer part is in the first 32 bits and the fraction part
in the last 32 bits [...] The precision of this representation is
about 200 picoseconds'' [3].
However, most computer systems cannot measure time to this resolution
(this represents a clock rate of 5 GHz). The POSIX gettimeofday()
function returns a ``struct timeval'' value, with a resolution of 1
microsecond. The POSIX clock_gettime() function returns a ``struct
timespec'' value, with a resolution of 1 nanosecond.
This API uses an extensible representation, but defaults to the
``struct timespec'' representation.
2.2 Time scale
Several different time scales have been proposed for use in computer
systems. UTC and TAI are the two obvious candidates.
Some people would prefer the use of TAI, which is identical to UTC
except that it does not correct for leap seconds. Their preference
for TAI stems from the difficulty of computing precise time
differences when leap seconds are involved, especially when using
times in the future (for which the exact number of leap seconds is,
in general, unknowable).
Mogul, Mills, Brittenson, Stone, Windl [Page 4]
Internet-Draft Pulse-Per-Second API 17 August 1999 11:18
However, POSIX and NTP both use UTC, albeit with different base
dates. Given that support for TAI would, in general, require other
changes to the POSIX specification, this API uses the POSIX base date
of 00:00 January 1, 1970 UTC, and conforms to the POSIX use of the
UTC time scale.
3 API
A PPS facility can be used in two different ways:
1. An application can obtain a timestamp, using the system's
internal timebase, for the most recent PPS event.
2. The kernel may directly utilize PPS events to discipline
its internal timebase, thereby providing highly accurate
time to all applications.
This API supports both uses, individually or in combination. The
timestamping feature may be used on any number of PPS sources
simultaneously; the timebase-disciplining feature may be used with at
most one PPS source.
Although the proper implementation of this API requires support from
the kernel of a UNIX system, this document defines the API in terms
of a set of library routines. This gives the implementor some
freedom to divide the effort between kernel code and library code
(different divisions might be appropriate on microkernels and
monolithic kernels, for example).
3.1 PPS abstraction
A PPS signal consists of a series of pulses, each with an
``asserted'' (logical true) phase, and a ``clear'' (logical false)
phase. The two phases may be of different lengths. The API may
capture an ``assert timestamp'' at the moment of the transition into
the asserted phase, and a ``clear timestamp'' at the moment of the
transition into the clear phase.
The specific assignment of the logical values ``true'' and ``false''
with specific voltages of a PPS signal, if applicable, is outside the
scope of this specification. However, these assignments SHOULD be
consistent with applicable standards. Implementors of PPS sources
SHOULD document these assignments.
---------
Reminder to implementors of DCD-based PPS support: TTL and
RS-232C (V.24/V.28) interfaces both define the "true" state as
the one having the highest positive voltage. TTL defines a
nominal absence of voltage as the "false" state, but RS-232C
(V.24/V.28) defines the "false" state by the presence of a
negative voltage.
---------
Mogul, Mills, Brittenson, Stone, Windl [Page 5]
Internet-Draft Pulse-Per-Second API 17 August 1999 11:18
The API supports the direct provision of PPS events (and timestamps)
to an in-kernel PPS consumer. This could be the function called
``hardpps()'', as described in RFC1589 [4], but the API does not
require the kernel implementation to use that function name
internally. The current version of the API supports at most one
in-kernel PPS consumer, and does not provide a way to explicitly name
it. The implementation SHOULD impose access controls on the use of
this feature.
The API optionally supports an ``echo'' feature, in which events on
the incoming PPS signal may be reflected through software, after the
capture of the corresponding timestamp, to an output signal pin.
This feature may be used to discover an upper bound on the actual
delay between the edges of the PPS signal and the capture of the
timestamps; such information may be useful in precise calibration of
the system.
The designation of an output pin for the echo signal, and sense and
shape of the output transition, is outside the scope of this
specification, but SHOULD be documented for each implementation. The
output pin MAY also undergo transitions at other times besides those
caused by PPS input events.
---------
Note: this allows an implementation of the echo feature to
generate an output pulse per input pulse, or an output edge per
input pulse, or an output pulse per input edge. It also allows
the same signal pin to be used for several purposes
simultaneously.
---------
Also, the API optionally provides an application with the ability to
specify an offset value to be applied to captured timestamps. This
can be used to correct for cable and/or radio-wave propagation
delays, or to compensate for systematic jitter in the external
signal. The implementation SHOULD impose access controls on the use
of this feature.
3.2 New data structures
The data structure declarations and symbol definitions for this API
will appear in the header file .
The API includes several implementation-specific types:
typedef ... pps_handle_t; /* represents a PPS source */
typedef unsigned ... pps_seq_t; /* sequence number */
The ``pps_handle_t'' type is an opaque scalar type used to represent
a PPS source within the API.
Mogul, Mills, Brittenson, Stone, Windl [Page 6]
Internet-Draft Pulse-Per-Second API 17 August 1999 11:18
The ``pps_seq_t'' type is an unsigned integer data type of at least
32 bits.
The precise declaration of the pps_handle_t and pps_seq_t types is
system-dependent.
The API imports the standard POSIX definition for this data type:
struct timespec {
time_t tv_sec; /* seconds */
long tv_nsec; /* nanoseconds */
};
The API defines this structure as an internal (not ``on the wire'')
representation of the NTP ``64-bit unsigned fixed-point'' timestamp
format [3]:
typedef struct ntp_fp {
unsigned int integral;
unsigned int fractional;
} ntp_fp_t;
The two fields in this structure may be declared as any unsigned
integral type, each of at least 32 bits.
The API defines this new union as an extensible type for representing
times:
typedef union pps_timeu {
struct timespec tspec;
ntp_fp_t ntpfp;
unsigned long longpad[3];
} pps_timeu_t;
Future revisions of this specification may add more fields to this
union.
---------
Note: adding a field to this union that is larger than
3*sizeof(long) will break binary compatibility.
---------
The API defines these new data structures:
typedef struct {
pps_seq_t assert_sequence; /* assert event seq # */
pps_seq_t clear_sequence; /* clear event seq # */
pps_timeu_t assert_tu;
pps_timeu_t clear_tu;
int current_mode; /* current mode bits */
Mogul, Mills, Brittenson, Stone, Windl [Page 7]
Internet-Draft Pulse-Per-Second API 17 August 1999 11:18
} pps_info_t;
#define assert_timestamp assert_tu.tspec
#define clear_timestamp clear_tu.tspec
#define assert_timestamp_ntpfp assert_tu.ntpfp
#define clear_timestamp_ntpfp clear_tu.ntpfp
typedef struct {
int api_version; /* API version # */
int mode; /* mode bits */
pps_timeu_t assert_off_tu;
pps_timeu_t clear_off_tu;
} pps_params_t;
#define assert_offset assert_off_tu.tspec
#define clear_offset clear_off_tu.tspec
#define assert_offset_ntpfp assert_off_tu.ntpfp
#define clear_offset_ntpfp clear_off_tu.ntpfp
The ``pps_info_t'' type is returned on an inquiry to PPS source. It
contains the timestamps for the most recent assert event, and the
most recent clear event. The order in which these events were
actually received is defined by the timetamps, not by any other
aspect of the specification. Each timestamp field represents the
value of the operating system's internal timebase when the
timestamped event occurred, or as close as possible to that time
(with the optional addition of a specified offset). The current_mode
field contains the value of the mode bits (see section 3.3) at the
time of the most recent transition was captured for this PPS source.
An application can use current_mode to discover the format of the
timestamps returned.
The assert_sequence number increases once per captured assert
timestamp. Its initial value is undefined. If incremented past the
largest value for the type, the next value is zero. The
clear_sequence number increases once per captured clear timestamp.
Its initial value is undefined, and may be different from the initial
value of assert_sequence. If incremented past the largest value for
the type, the next value is zero. Due to possible signal loss or
excessive signal noise, the assert-sequence number and the
clear-sequence number might not always increase in step with each
other.
---------
Note that these sequence numbers are most useful in
applications where events other than PPS transitions are to be
captured, which might be involved in a precision stopwatch
application, for example. In such cases, the sequence numbers
may be used to detect overruns, where the application has
Mogul, Mills, Brittenson, Stone, Windl [Page 8]
Internet-Draft Pulse-Per-Second API 17 August 1999 11:18
missed one or more events. They may also be used to detect an
excessive event rate, or to detect that an event has failed to
occur between two calls to the time_pps_fetch() function
(defined later).
In order to obtain an uninterrupted series of sequence numbers
(and hence of event timestamps), it may be necessary to sample
the pps_info_t values at a rate somewhat faster than the
underlying event rate. For example, an application interested
in both assert and clear timestamps may need to sample at least
twice per second. Proper use of the sequence numbers allows an
application to discover if it has missed any event timestamps
due to an insufficient sampling rate.
---------
The pps_params_t data type is used to discover and modify parameters
of a PPS source. The data type includes a mode field, described in
section 3.3. It also includes an api_version field, a read-only
value giving the version of the API. Currently, the only defined
value is:
#define PPS_API_VERS_1 1
This field is present to enable binary compatibility with future
versions of the API.
As an OPTIONAL feature of the API, the implementation MAY support
adding offsets to the timestamps that are captured. (Values of type
``struct timespec'' can represent negative offsets.) The
assert_offset field of a pps_params_t value specifies a value to be
added to generate a captured assert_timestamp. The clear_offset of a
pps_params_t value field specifies a value to be added to generate a
captured clear_timestamp. Since the offsets, if any, apply to all
users of a given PPS source, the implementation SHOULD impose access
controls on the use of this feature; for example, allowing only the
super-user to set the offset values. The default value for both
offsets is zero.
3.3 Mode bit definitions
A set of mode bits is associated with each PPS source.
The bits in the mode field of the pps_params_t type are:
/* Device/implementation parameters */
#define PPS_CAPTUREASSERT 0x01
#define PPS_CAPTURECLEAR 0x02
#define PPS_CAPTUREBOTH 0x03
#define PPS_OFFSETASSERT 0x10
#define PPS_OFFSETCLEAR 0x20
Mogul, Mills, Brittenson, Stone, Windl [Page 9]
Internet-Draft Pulse-Per-Second API 17 August 1999 11:18
#define PPS_CANWAIT 0x100
#define PPS_CANPOLL 0x200
/* Kernel actions */
#define PPS_ECHOASSERT 0x40
#define PPS_ECHOCLEAR 0x80
/* Timestamp formats */
#define PPS_TSFMT_TSPEC 0x1000
#define PPS_TSFMT_NTPFP 0x2000
These mode bits are divided into three categories:
1. Device/implementation parameters: These are parameters
either of the device or of the implementation. If the
implementation allows these to be changed, then these bits
are read/write for users with sufficient privilege (such
as the super-user), and read-only for other users. If the
implementation does not allow these bits to be changed,
they are read-only.
2. Kernel actions: These bits specify certain kernel actions
to be taken on arrival of a signal. If the implementation
supports one of these actions, then the corresponding bit
is read/write for users with sufficient privilege (such as
the super-user), and read-only for other users. If the
implementation does not support the action, the
corresponding bit is always zero.
3. Timestamp formats: These bits indicate the set of
timestamp formats available for the device. They are
always read-only.
In more detail, the meanings of the Device/implementation parameter
mode bits are:
PPS_CAPTUREASSERT
If this bit is set, the assert timestamp for the
associated PPS source will be captured.
PPS_CAPTURECLEAR
If this bit is set, the clear timestamp for the
associated PPS source will be captured.
PPS_CAPTUREBOTH Defined as the union of PPS_CAPTUREASSERT and
PPS_CAPTURECLEAR, for convenience.
PPS_OFFSETASSERT
If set, the assert_offset value is added to the
current value of the operating system's internal
timebase in order to generate the captured
assert_timestamp.
Mogul, Mills, Brittenson, Stone, Windl [Page 10]
Internet-Draft Pulse-Per-Second API 17 August 1999 11:18
PPS_OFFSETCLEAR If set, the clear_offset value is added to the
current value of the operating system's internal
timebase in order to generate the captured
clear_timestamp.
PPS_CANWAIT If set, the application may request that the
time_pps_fetch() function (see section 3.4.3) should
block until the next timestamp arrives. Note: this
mode bit is read-only.
PPS_CANPOLL This bit is reserved for future use. An application
SHOULD NOT depend on any functionality implied either
by its presence or by its absence.
If neither PPS_CAPTUREASSERT nor PPS_CAPTURECLEAR is set, no valid
timestamp will be available via the API.
The meanings of the Kernel action mode bits are:
PPS_ECHOASSERT If set, after the capture of an assert timestamp,
the implementation generates a signal transition as
rapidly as possible on an output signal pin. This
MUST NOT affect the delay between the PPS source's
transition to the asserted phase and the capture of
the assert timestamp.
PPS_ECHOCLEAR If set, after the capture of a clear timestamp, the
implementation generates a signal transition as
rapidly as possible on an output signal pin. This
MUST NOT affect the delay between the PPS source's
transition to the clear phase and the capture of the
clear timestamp.
The timestamp formats are:
PPS_TSFMT_TSPEC Timestamps and offsets are represented as values of
type ``struct timespec''. All implementations MUST
support this format, and this format is the default
unless an application specifies otherwise.
PPS_TSFMT_NTPFP Timestamps and offsets are represented as values of
type ``ntp_fp_t'', which corresponds to the NTP
``64-bit unsigned fixed-point'' timestamp format [3].
Support for this format is OPTIONAL.
Other timestamp format bits may be defined as fields are added to the
``pps_timeu_t'' union.
The operating system may implement all of these mode bits, or just a
subset of them. If an attempt is made to set an unsupported mode
bit, the API will return an error. If an attempt is made to modify a
read-only mode bit, the API will return an error.
Mogul, Mills, Brittenson, Stone, Windl [Page 11]
Internet-Draft Pulse-Per-Second API 17 August 1999 11:18
3.4 New functions
In the description of functions that follows, we use the following
function parameters:
filedes A file descriptor (type: int), for a serial line or
other source of PPS events.
ppshandle A variable of type ``pps_handle_t'', as defined in
section 3.2.
ppsinfobuf A record of type ``pps_info_t'', as defined in
section 3.2.
ppsparams A record of type ``pps_params_t'', as defined in
section 3.2.
tsformat An integer with exactly one of the timestamp format
bits set.
Mogul, Mills, Brittenson, Stone, Windl [Page 12]
Internet-Draft Pulse-Per-Second API 17 August 1999 11:18
3.4.1 New functions: obtaining PPS sources
The API includes a function to create and destroy PPS source
``handles''.
SYNOPSIS
int time_pps_create(int filedes, pps_handle_t *handle);
int time_pps_destroy(pps_handle_t handle);
DESCRIPTION
All of the other functions in the PPS API operate on PPS handles
(type: pps_handle_t). The time_pps_create() is used to convert an
already-open UNIX file descriptor, for an appropriate special file,
into a PPS handle.
The definition of what special files are appropriate for use with the
PPS API is outside the scope of this specification, and may vary
based on both operating system implementation, and local system
configuration. One typical case is a serial line, whose DCD pin is
connected to a source of PPS events.
The mode in which the UNIX file descriptor was originally opened
affects what operations are allowed on the PPS handle. The
time_pps_setparams() and time_pps_kcbind() functions (see sections
3.4.2 and 3.4.4) SHOULD be prohibited by the implementation if the
descriptor is open only for reading (O_RDONLY).
---------
Note: operations on a descriptor opened with an inappropriate
mode might fail with EBADF.
---------
The time_pps_destroy() function makes the PPS handle unusable, and
frees any storage that might have been allocated for it. It does not
close the associated file descriptor, nor does it change any of the
parameter settings for the PPS source.
---------
Note: If this API is adapted to an operating system that does
not follow UNIX conventions for representing an accessible PPS
source as an integer file descriptor, the time_pps_create()
function may take different parameters from those shown here.
---------
Mogul, Mills, Brittenson, Stone, Windl [Page 13]
Internet-Draft Pulse-Per-Second API 17 August 1999 11:18
RETURN VALUES
On successful completion, the time_pps_create() function returns 0.
Otherwise, a value of -1 is returned and errno is set to indicate the
error.
If called with a valid handle parameter, the time_pps_destroy()
function returns 0. Otherwise, it returns -1.
ERRORS
If the time_pps_create() function fails, errno may be set to one of
the following values:
[EBADF] The filedes parameter is not a valid file descriptor.
[EOPNOTSUPP] The use of the PPS API is not supported for the file
descriptor.
[EPERM] The process's effective user ID does not have the
required privileges to use the PPS API.
Mogul, Mills, Brittenson, Stone, Windl [Page 14]
Internet-Draft Pulse-Per-Second API 17 August 1999 11:18
3.4.2 New functions: setting PPS parameters
The API includes several functions use to set or obtain the
parameters of a PPS source.
SYNOPSIS
int time_pps_setparams(pps_handle_t handle,
const pps_params_t *ppsparams);
int time_pps_getparams(pps_handle_t handle,
pps_params_t *ppsparams);
int time_pps_getcap(pps_handle_t handle, int *mode);
DESCRIPTION
A suitably privileged application may use time_pps_setparams() to set
the parameters (mode bits and timestamp offsets) for a PPS source.
The pps_params_t type is defined in section 3.2; mode bits are
defined in section 3.3. An application may use time_pps_getparams()
to discover the current settings of the PPS parameters. An
application that needs to change only a subset of the existing
parameters must first call time_pps_getparams() to obtain the current
parameter values, then set the new values using time_pps_setparams().
---------
Note: a call to time_pps_setparams() replaces the current
values of all mode bits with those specified via the ppsparams
argument, except those bits whose state cannot be changed.
Bits might be read-only due to access controls, or because they
are fixed by the implementation.
---------
The timestamp format of the assert_offset and clear_offset fields is
defined by the mode field. That is, on a call to
time_pps_setparams(), the kernel interprets the supplied offset
values using the timestamp format given in the mode field of the
ppsparams argument. If the requested timestamp format is not
supported, the time_pps_setparams() function has no effect and
returns an error value. On a call to time_pps_getparams(), the
kernel provides the timestamp format of the offsets by setting one of
the timestamp format bits in the mode field.
---------
Note: an application that uses time_pps_getparams() to read the
current offset values cannot specify which format is used. The
implementation SHOULD return the offsets using the same
timestamp format as was used when the offsets were set.
---------
Mogul, Mills, Brittenson, Stone, Windl [Page 15]
Internet-Draft Pulse-Per-Second API 17 August 1999 11:18
An application wishing to discover which mode bits it may set, with
its current effective user ID, may call time_pps_getcap(). This
function returns the set of mode bits that may be set by the
application, without generating an EINVAL or EPERM error, for the
specified PPS source. It does not return the current values for the
mode bits. A call to time_pps_getcap() returns the mode bits
corresponding to all supported timestamp formats.
The time_pps_getcap() function MAY ignore the mode in which the
associated UNIX file descriptor was opened, so the application might
still receive an EBADF error on a call to time_pps_setparams(), even
if time_pps_getcap() says that the chosen mode bits are allowed.
The mode bits returned by time_pps_getcap() for distinct PPS handles
may differ, reflecting the specific capabilities of the underlying
hardware connection to the PPS source, or of the source itself.
RETURN VALUES
On successful completion, the time_pps_setparams(),
time_pps_getparams(), and time_pps_getcap() functions return 0.
Otherwise, a value of -1 is returned and errno is set to indicate the
error.
ERRORS
If the time_pps_setparams(), time_pps_getparams(), or
time_pps_getcap() function fails, errno may be set to one of the
following values:
[EBADF] The handle parameter is not associated with a valid
file descriptor, or the descriptor is not open for
writing.
[EFAULT] A parameter points to an invalid address.
[EOPNOTSUPP] The use of the PPS API is not supported for the
associated file descriptor.
[EINVAL] The operating system does not support all of the
requested mode bits.
[EPERM] The process's effective user ID does not have the
required privileges to use the PPS API, or to set the
given mode bits.
Mogul, Mills, Brittenson, Stone, Windl [Page 16]
Internet-Draft Pulse-Per-Second API 17 August 1999 11:18
3.4.3 New functions: access to PPS timestamps
The API includes one function that gives applications access to PPS
timestamps. As an implementation option, the application may request
the API to block until the next timestamp is captured. (The API does
not directly support the use of the select() or poll() system calls
to wait for PPS events.)
SYNOPSIS
int time_pps_fetch(pps_handle_t handle,
const int tsformat,
pps_info_t *ppsinfobuf,
const struct timespec *timeout);
DESCRIPTION
An application may use time_pps_fetch() to obtain the most recent
timestamps captured for the PPS source specified by the handle
parameter. The tsformat parameter specifies the desired timestamp
format; if the requested timestamp format is not supported, the call
fails and returns an error value.
This function blocks until either a timestamp is captured from the
PPS source, or until the specified timeout duration has expired. If
the timeout parameter is a NULL pointer, the function simply blocks
until a timestamp is captured. If the timeout parameter specifies a
delay of zero, the function returns immediately.
Support for blocking behavior is an implementation option. If the
PPS_CANWAIT mode bit is clear, and the timeout parameter is either
NULL or points to a non-zero value, the function returns an
EOPNOTSUPP error. An application can discover whether the feature is
implemented by using time_pps_getcap() to see if the PPS_CANWAIT mode
bit is set.
The result is stored in the ppsinfobuf parameter, whose fields are
defined in section 3.2. If the function returns as the result of a
timeout or error, the contents of the ppsinfobuf are undefined.
If this function is invoked before the system has captured a
timestamp for the signal source, the ppsinfobuf returned will have
its timestamp fields set to the time format's base date (e.g., for
PPS_TSFMT_TSPEC, both the tv_sec and tv_nsec fields will be zero).
Mogul, Mills, Brittenson, Stone, Windl [Page 17]
Internet-Draft Pulse-Per-Second API 17 August 1999 11:18
RETURN VALUES
On successful completion, the time_pps_fetch() function returns 0.
Otherwise, a value of -1 is returned and errno is set to indicate the
error.
ERRORS
If the time_pps_fetch() function fails, errno may be set to one of
the following values:
[EBADF] The handle parameter is not associated with a valid
file descriptor.
[EFAULT] A parameter points to an invalid address.
[EINTR] A signal was delivered before the time limit
specified by the timeout parameter expired and before
a timestamp has been captured.
[EINVAL] The requested timestamp format is not supported.
[EOPNOTSUPP] The use of the PPS API is not supported for the
associated file descriptor.
[ETIMEDOUT] The timeout duration has expired.
Mogul, Mills, Brittenson, Stone, Windl [Page 18]
Internet-Draft Pulse-Per-Second API 17 August 1999 11:18
3.4.4 New functions: disciplining the kernel timebase
The API includes one OPTIONAL function to specify if and how a PPS
source is provided to a kernel consumer of PPS events, such as the
code used to discipline the operating system's internal timebase.
SYNOPSIS
int time_pps_kcbind(pps_handle_t handle,
const int kernel_consumer,
const int edge,
const int tsformat);
DESCRIPTION
An application with appropriate privileges may use time_pps_kcbind()
to bind a kernel consumer to the PPS source specified by the handle.
The kernel consumer is identified by the kernel_consumer parameter.
In the current version of the API, the possible values for this
parameter are:
#define PPS_KC_HARDPPS 0
#define PPS_KC_HARDPPS_PLL 1
#define PPS_KC_HARDPPS_FLL 2
with these meanings:
PPS_KC_HARDPPS The kernel's hardpps() function (or equivalent).
PPS_KC_HARDPPS_PLL
A variant of hardpps() constrained to use a
phase-locked loop.
PPS_KC_HARDPPS_FLL
A variant of hardpps() constrained to use a
frequency-locked loop.
Support for any or all of these values is OPTIONAL.
The edge parameter indicates which edge of the PPS signal causes a
timestamp to be delivered to the kernel consumer. It may have the
value PPS_CAPTUREASSERT, PPS_CAPTURECLEAR, or PPS_CAPTUREBOTH,
depending on particular characteristics of the PPS source. It may
also be zero, which removes any binding between the PPS source and
the kernel consumer.
The tsformat parameter specifies the format for the timestamps
delivered to the kernel consumer. If this value is zero, the
implementation MAY choose the appropriate format, or return EINVAL.
The implementation MAY ignore a non-zero value for this parameter.
Mogul, Mills, Brittenson, Stone, Windl [Page 19]
Internet-Draft Pulse-Per-Second API 17 August 1999 11:18
The binding created by this call persists until it is changed by a
subsequent call specifying the same kernel_consumer. In particular,
a subsequent call to time_pps_destroy() for the specified handle does
not affect the binding.
The binding is independent of any prior or subsequent changes to the
PPS_CAPTUREASSERT and PPS_CAPTURECLEAR mode bits for the device.
However, if either the edge or the tsformat parameter values are
inconsistent with the capabilities of the PPS source, an error is
returned. The implementation MAY also return an error if the
tsformat value is unsupported for time_pps_kcbind(), even if it is
supported for other uses of the API.
The operating system may enforce two restrictions on the bindings
created by time_pps_kcbind():
1. the kernel MAY return an error if an attempt is made to
bind a kernel consumer to more than one PPS source a time.
2. the kernel MAY restrict the ability to set bindings to
processes with sufficient privileges to modify the
system's internal timebase. (On UNIX systems, such
modification is normally done using settimeofday() and/or
adjtime(), and is restricted to users with superuser
privilege.)
---------
Warning: If this feature is configured for a PPS source that
does not have an accurate 1-pulse-per-second signal, or is
otherwise inappropriately configured, use of this feature may
result in seriously incorrect timekeeping for the entire
system. For best results, the 1-PPS signal should have much
better frequency stability than the system's internal clock
source (usually a crystal-controlled oscillator), and should
have jitter (variation in interarrival time) much less than the
system's clock-tick interval.
---------
See RFC1589 [4] for more information about how the system's timebase
may be disciplined using a PPS signal.
RETURN VALUES
On successful completion, the time_pps_kcbind() function returns 0.
Otherwise, a value of -1 is returned and errno is set to indicate the
error.
Mogul, Mills, Brittenson, Stone, Windl [Page 20]
Internet-Draft Pulse-Per-Second API 17 August 1999 11:18
ERRORS
If the time_pps_kcbind() function fails, errno may be set to one of
the following values:
[EBADF] The handle parameter is not associated with a valid
file descriptor, or the descriptor is not open for
writing.
[EFAULT] A parameter points to an invalid address.
[EINVAL] The requested timestamp format is not supported.
[EOPNOTSUPP] The use of the PPS API is not supported for the
associated file descriptor, or this OPTIONAL function
is not supported.
[EPERM] The process's effective user ID does not have the
required privileges to set the binding.
Mogul, Mills, Brittenson, Stone, Windl [Page 21]
Internet-Draft Pulse-Per-Second API 17 August 1999 11:18
3.5 Compliance rules
The key words "MUST", "MUST NOT", "REQUIRED","SHOULD", SHOULD NOT",
"MAY", and "OPTIONAL" in this document are to be interpreted as
described in RFC2119 [1].
Some features of this specification are OPTIONAL, but others are
REQUIRED.
3.5.1 Functions
An implementation MUST provide these functions:
- time_pps_create()
- time_pps_destroy()
- time_pps_setparams()
- time_pps_getparams()
- time_pps_getcap()
- time_pps_fetch()
An implementation MUST provide this function, but it may be
implemented as a function that always return an EOPNOTSUPP error,
possibly on a per-source basis:
- time_pps_kcbind()
3.5.2 Mode bits
An implementation MUST support at least one of these mode bits for
each PPS source:
- PPS_CAPTUREASSERT
- PPS_CAPTURECLEAR
and MAY support both of them. If an implementation supports both of
these bits for a PPS source, it SHOULD allow them to be set
simultaneously.
An implementation MUST support this timestamp format:
- PPS_TSFMT_TSPEC
An implementation MAY support these mode bits:
- PPS_ECHOASSERT
- PPS_ECHOCLEAR
- PPS_OFFSETASSERT
- PPS_OFFSETCLEAR
An implementation MAY support this timestamp format:
- PPS_TSFMT_NTPFP
Mogul, Mills, Brittenson, Stone, Windl [Page 22]
Internet-Draft Pulse-Per-Second API 17 August 1999 11:18
3.6 Examples
A very simple use of this API might be:
int fd;
pps_handle_t handle;
pps_params_t params;
pps_info_t infobuf;
struct timespec timeout;
/* Open a file descriptor and enable PPS on rising edges */
fd = open(PPSfilename, O_RDWR, 0);
time_pps_create(fd, &handle);
time_pps_getparams(handle, ¶ms);
if ((params.mode & PPS_CAPTUREASSERT) == 0) {
fprintf(stderr, "%s cannot currently CAPTUREASSERT\n",
PPSfilename);
exit(1);
}
/* create a zero-valued timeout */
timeout.tv_sec = 0;
timeout.tv_nsec = 0;
/* loop, printing the most recent timestamp every second or so */
while (1) {
sleep(1);
time_pps_fetch(handle, PPS_TSFMT_TSPEC, &infobuf, &timeout);
printf("Assert timestamp: %d.%09d, sequence: %ld\n",
infobuf.assert_timestamp.tv_sec,
infobuf.assert_timestamp.tv_nsec,
infobuf.assert_sequence);
}
Note that this example omits most of the error-checking that would be
expected in a reliable program.
Also note that, on a system that supports PPS_CANWAIT, the function
of these lines:
sleep(1);
time_pps_fetch(handle, PPS_TSFMT_TSPEC, &infobuf, &timeout);
might be more reliably accomplished using:
timeout.tv_sec = 100;
timeout.tv_nsec = 0;
time_pps_fetch(handle, PPS_TSFMT_TSPEC, &infobuf, &timeout);
The (arbitrary) timeout value is used to protect against the
possibility that another application might disable PPS timestamps, or
that the hardware generating the timestamps might fail.
Mogul, Mills, Brittenson, Stone, Windl [Page 23]
Internet-Draft Pulse-Per-Second API 17 August 1999 11:18
A slightly more elaborate use of this API might be:
int fd;
pps_handle_t handle;
pps_params_t params;
pps_info_t infobuf;
int avail_mode;
struct timespec timeout;
/* Open a file descriptor */
fd = open(PPSfilename, O_RDWR, 0);
time_pps_create(fd, &handle);
/*
* Find out what features are supported
*/
time_pps_getcap(handle, &avail_mode);
if ((avail_mode & PPS_CAPTUREASSERT) == 0) {
fprintf(stderr, "%s cannot CAPTUREASSERT\n", PPSfilename);
exit(1);
}
if ((avail_mode & PPS_OFFSETASSERT) == 0) {
fprintf(stderr, "%s cannot OFFSETASSERT\n", PPSfilename);
exit(1);
}
/*
* Capture assert timestamps, and
* compensate for a 675 nsec propagation delay
*/
time_pps_getparams(handle, ¶ms);
params.assert_offset.tv_sec = 0;
params.assert_offset.tv_nsec = 675;
params.mode |= PPS_CAPTUREASSERT | PPS_OFFSETASSERT;
time_pps_setparams(handle, ¶ms);
/* create a zero-valued timeout */
timeout.tv_sec = 0;
timeout.tv_nsec = 0;
/* loop, printing the most recent timestamp every second or so */
while (1) {
if (avail_mode & PPS_CANWAIT) {
time_pps_fetch(handle, PPS_TSFMT_TSPEC, &infobuf, NULL);
/* waits for the next event */
} else {
sleep(1);
time_pps_fetch(handle, PPS_TSFMT_TSPEC, &infobuf,
timeout);
Mogul, Mills, Brittenson, Stone, Windl [Page 24]
Internet-Draft Pulse-Per-Second API 17 August 1999 11:18
}
printf("Assert timestamp: %d.%09d, sequence: %ld\n",
infobuf.assert_timestamp.tv_sec,
infobuf.assert_timestamp.tv_nsec,
infobuf.assert_sequence);
}
Again, most of the necessary error-checking has been omitted from
this example.
4 Security Considerations
This API gives applications three capabilities:
- Causing the system to capture timestamps on certain events.
- Obtaining timestamps for certain events.
- Affecting the system's internal timebase.
The first capability should not affect security directly, but might
cause a slight increase in interrupt latency and interrupt-handling
overhead.
The second capability might be useful in implementing certain kinds
of covert communication channels.
In most cases, neither of these first two issues is a significant
security threat, because the traditional UNIX file protection
facility may be used to to limit access to the relevant special
files. Provision of the PPS API adds minimal additional risk.
The final capability is reserved to highly privileged users. In UNIX
systems, this means those with superuser privilege. Such users can
evade protections based on file permissions; however, such users can
in general cause unbounded havoc, and can set the internal timebase
(and its rate of change), so this API creates no new vulnerabilities.
5 Acknowledgements
The API in this document draws some of its inspiration from the LBL
``ppsclock'' distribution [2], originally implemented in 1993 by
Steve McCanne, Craig Leres, and Van Jacobson. We also thank
Poul-Henning Kamp, Craig Leres, Judah Levine, and Harlan Stenn for
helpful comments they contributed during the drafting of this
document.
Mogul, Mills, Brittenson, Stone, Windl [Page 25]
Internet-Draft Pulse-Per-Second API 17 August 1999 11:18
6 References
1. Scott Bradner. Key words for use in RFCs to Indicate Requirement
Levels. RFC 2119, Harvard University, March, 1997.
2. Steve McCanne, Craig Leres, and Van Jacobson. PPSCLOCK.
ftp://ftp.ee.lbl.gov/ppsclock.tar.Z.
3. David L. Mills. Network Time Protocol (Version 3):
Specification, Implementation and Analysis. RFC 1305, IETF, March,
1992.
4. David L. Mills. A Kernel Model for Precision Timekeeping. RFC
1589, IETF, March, 1994.
5. The Open Group. The Single UNIX Specification, Version 2 - 6 Vol
Set for UNIX 98. Document number T912, The Open Group, February,
1997.
7 Authors' addresses
Jeffrey C. Mogul
Western Research Laboratory
Compaq Computer Corporation
250 University Avenue
Palo Alto, California, 94305, U.S.A.
Email: mogul@wrl.dec.com
Phone: 1 650 617 3304 (email preferred)
David L. Mills
Electrical and Computer Engineering Department
University of Delaware
Newark, DE 19716
Phone: (302) 831-8247
EMail: mills@udel.edu
Jan Brittenson
Sun Microsystems, Inc.
901 San Antonio Rd M/S MPK17-202
Palo Alto, CA 94303
Email: Jan.Brittenson@Eng.Sun.COM
Jonathan Stone
Stanford Distributed Systems Group
Stanford, CA 94305
Phone: (650) 723-2513
Email: jonathan@dsg.stanford.edu
Mogul, Mills, Brittenson, Stone, Windl [Page 26]
Internet-Draft Pulse-Per-Second API 17 August 1999 11:18
Ulrich Windl
Universitaet Regensburg, Klinikum
Email: ulrich.windl@rz.uni-regensburg.de
A. Extensions and related APIs
The API specified in the main body of this document could be more
useful with the provision of several extensions or companion APIs.
At present, the interfaces listed in this appendix are not part of
the formal specification in this document.
A.1 Extension: Parameters for the ``echo'' mechanism
The ``echo'' mechanism described in the body of this specification
leaves most of the details to the implementor, especially the
designation of one or more output pins.
It might be useful to extend this API to provide either or both of
these features:
- A means by which the application can discover which output
pin is echoing the input pin.
- A means by which the application can select which output
pin is echoing the input pin.
A.2 Extension: Obtaining information about external clocks
The PPS API may be useful with a wide variety of reference clocks,
connected via several different interface technologies (including
serial lines, parallel interfaces, and bus-level interfaces). These
reference clocks can have many features and parameters, some of which
might not even have been invented yet.
We believe that it would be useful to have a mechanism by which an
application can discover arbitrary features and parameters of a
reference clock. These might include:
- Clock manufacturer, model number, and revision level
- Whether the clock is synchronized to an absolute standard
- For synchronized clocks,
* The specific standard
* The accuracy of the standard
* The path used (direct connection, shortwave, longwave,
satellite, etc.)
* The distance (offset) and variability of this path
Mogul, Mills, Brittenson, Stone, Windl [Page 27]
Internet-Draft Pulse-Per-Second API 17 August 1999 11:18
- For PPS sources,
* The pulse rate
* The pulse shape
* Which edge of the pulse corresponds to the epoch
- The time representation format
This information might best be provided by an API analogous to the
standard ``curses'' API, with a database analogous to the standard
``terminfo'' database. That is, a ``clockinfo'' database would
contain a set of (attribute, value) pairs for each type of clock, and
the API would provide a means to query this database.
Additional mechanisms would allow an application to discover the
clock or clocks connected to the local system, and to discover the
clockinfo type of a specific clock device.
A.3 Extension: Finding a PPS source
Although the clockinfo database described in section A.2, together
with the discover mechanisms described there, would allow an
application to discover the PPS source (or sources) connected to a
system, it might be more complex than necessary.
A simpler approach would be to support a single function that
provides the identity of one or more PPS sources.
For example, the function might be declared as
int time_pps_findsource(int index,
char *path, int pathlen,
char *idstring, int idlen);
The index argument implicitly sets up an ordering on the PPS sources
attached to the system. An application would use this function to
inquire about the Nth source. The function would return -1 if no
such source exists; otherwise, it would return 0, and would place the
pathname of the associated special file in the path argument. It
would also place an identification string in the idstring argument.
The identification string could include the clock make, model,
version, etc., which could then be used by the application to control
its behavior.
This function might simply read the Nth line from a simple database,
containing lines such as:
/dev/tty00 "TrueTime 468-DC"
/dev/pps1 "Homebrew rubidium frequency standard"
Mogul, Mills, Brittenson, Stone, Windl [Page 28]
Internet-Draft Pulse-Per-Second API 17 August 1999 11:18
allowing the system administrator to describe the configuration of
PPS sources.
B. Example implementation: PPSDISC Line discipline
One possible implementation of the PPS API might be to define a new
``line discipline'' and then map the API onto a set of ioctl()
commands. Here we sketch such an implementation; note that this is
not part of the specification of the API, and applications should not
expect this low-level interface to be available.
In this approach, the set of line disciplines is augmented with one
new line discipline, PPSDISC. This discipline will act exactly the
same as the TTYDISC discipline, except for its handling of modem DCD
interrupts.
Once the TIOCSETD ioctl() has been used to select this line
discipline, PPS-related operations on the serial line may be invoked
using new ioctl() commands. For example (values used only for
illustration):
#define PPSFETCH _IOR('t', 75, pps_info_t)
#define PPSSETPARAM _IOW('t', 76, pps_params_t)
#define PPSGETPARAM _IOR('t', 77, pps_params_t)
#define PPSGETCAP _IOR('t', 78, int)
B.1 Example
A typical use might be:
int ldisc = PPSDISC;
pps_params_t params;
pps_info_t infobuf;
ioctl(fd, TIOCSETD, &ldisc); /* set discipline */
/*
* Check the capabilities of this PPS source to see
* if it supports what we need.
*/
ioctl(fd, PPSGETCAP, ¶ms);
if ((params.mode & PPS_CAPTUREASSERT) == 0) {
fprintf(stderr, "PPS source is not suitable\n");
exit(1);
}
/*
* Set this line to timestamp on a rising-edge interrupt
Mogul, Mills, Brittenson, Stone, Windl [Page 29]
Internet-Draft Pulse-Per-Second API 17 August 1999 11:18
*/
ioctl(fd, PPSGETPARAMS, ¶ms);
params.mode |= PPS_CAPTUREASSERT;
ioctl(fd, PPSSETPARAMS, ¶ms);
sleep(2); /* allow time for the PPS pulse to happen */
/* obtain most recent timestamp and sequence # for this line */
ioctl(fd, PPSFETCH, &infobuf);
Again, this example imprudently omits any error-checking.
C. Available implementations
Several available implementations of this API are listed at
. Note that not all of
these implementations correspond to the current version of the
specification.
Mogul, Mills, Brittenson, Stone, Windl [Page 30]