Internet Draft
Network Working Group J. Cucchiara
Internet-Draft Brix Networks
Expires September 2000 H. Sjostrand
Ericsson
J. Luciani
TollBridge Technologies
March 2000
Definitions of Managed Objects for
the Multiprotocol Label Switching, Label Distribution Protocol (LDP)
<draft-ietf-mpls-ldp-mib-05.txt>
Status of this Memo
This document is an Internet-Draft and is in full conformance with
all provisions of Section 10 of RFC 2026. Internet-Drafts are
working documents of the Internet Engineering Task Force (IETF), its
areas, and its working groups. Note that other groups may also
distribute working documents as Internet-Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress".
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html
Distribution of this document is unlimited. Please send comments to
the Multiprotocol Label Switching (mpls) Working Group, draft-ietf-mpls-ldp-mib-04.txt> .............. 63
5.2 Changes from <draft-ietf-mpls-ldp-mib-03.txt> .............. 65
5.3 Changes from <draft-ietf-mpls-ldp-mib-02.txt> .............. 66
5.4 Changes from <draft-ietf-mpls-ldp-mib-01.txt> .............. 67
5.5 Changes from <draft-ietf-mpls-ldp-mib-00.txt> .............. 68
6 TO DO List ................................................... 69
7 Acknowledgments .............................................. 69
8 References ................................................... 70
9 Security Considerations ...................................... 72
10 Authors' Addresses .......................................... 73
11 Full Copyright Statement .................................... 74
Expires September 2000 [Page 2]
INTERNET-DRAFT MPLS LDP MIB March 2000
1. Introduction
This memo defines a portion of the Management Information Base (MIB)
for use with network management protocols in the Internet community.
In particular, it describes managed objects for the Multiprotocol
Label Switching, Label Distribution Protocol (LDP) [18].
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [22].
2. The SNMP Management Framework
The SNMP Management Framework presently consists of five major
components:
o An overall architecture, described in RFC 2571 [RFC2571].
o Mechanisms for describing and naming objects and events for the
purpose of management. The first version of this Structure of
Management Information (SMI) is called SMIv1 and described in
STD 16, RFC 1155 [RFC1155], STD 16, RFC 1212 [RFC1212] and RFC
1215 [RFC1215]. The second version, called SMIv2, is described
in STD 58, RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and
STD 58, RFC 2580 [RFC2580].
o Message protocols for transferring management information. The
first version of the SNMP message protocol is called SNMPv1 and
described in STD 15, RFC 1157 [RFC1157]. A second version of
the SNMP message protocol, which is not an Internet standards
track protocol, is called SNMPv2c and described in RFC 1901
[RFC1901] and RFC 1906 [RFC1906]. The third version of the
message protocol is called SNMPv3 and described in RFC 1906
[RFC1906], RFC 2572 [RFC2572] and RFC 2574 [RFC2574].
o Protocol operations for accessing management information. The
first set of protocol operations and associated PDU formats is
described in STD 15, RFC 1157 [RFC1157]. A second set of
protocol operations and associated PDU formats is described in
RFC 1905 [RFC1905].
o A set of fundamental applications described in RFC 2573
[RFC2573] and the view-based access control mechanism described
in RFC 2575 [RFC2575].
A more detailed introduction to the current SNMP Management Framework
can be found in RFC 2570 [RFC2570].
Managed objects are accessed via a virtual information store, termed
Expires September 2000 [Page 3]
INTERNET-DRAFT MPLS LDP MIB March 2000
the Management Information Base or MIB. Objects in the MIB are
defined using the mechanisms defined in the SMI.
This memo specifies a MIB module that is compliant to the SMIv2. A
MIB conforming to the SMIv1 can be produced through the appropriate
translations. The resulting translated MIB must be semantically
equivalent, except where objects or events are omitted because no
translation is possible (use of Counter64). Some machine readable
information in SMIv2 will be converted into textual descriptions in
SMIv1 during the translation process. However, this loss of machine
readable information is not considered to change the semantics of the
MIB.
Expires September 2000 [Page 4]
INTERNET-DRAFT MPLS LDP MIB March 2000
3. Structure of the MIB
This memo defines a portion of the Management Information Base (MIB)
for use with network management protocols in the Internet community.
In particular, it describes managed objects for the Multiprotocol
Label Switching, Label Distribution Protocol (LDP) as defined in
[18].
3.1. Overview
The MIB provides objects to configure/set-up potential LDP sessions
on a specific LSR. A table is used to configure potential LDP
Sessions, where each row in the table initiates an LDP Session. This
is the mplsLdpEntityTable.
Another table, the mplsLdpEntityPeerTable, is a read-only table which
records information learned via discovery or from the session
initialization message. Each row in the EntityPeer Table represents
a peer which is known to a specific Entity. This table carries
information which is specific to the Entity-Peer interactions but is
not appropriate for the mplsLdpSessionTable.
A third table is used to show the actual sessions which have been, or
are in the process of being established. Each row represents a
specific session between an Entity (on this LSR) and a peer.
3.2. Interface Indexing
Interface Indexes as specified in [29] are used in the MIB. The
descriptions of the ifIndexes denote which ifIndex is being used.
NOTE: the use of ifIndex is for actual existing connections.
3.3. Future Considerations
The following aspects are not addressed in this document: VPN issues
(i.e. potential MIB objects such as the VPN Identifier are not
included at this time), and lastly, multicast issues are not
discussed.
Some of these issues need further clarification before adding to the
MIB.
3.4. Discussion of MIB Groups
Currently, there are four groups: the MPLS LDP General Group, the
MPLS LDP ATM Group, the MPLS LDP Frame Relay Group and the MPLS LDP
Notifications Group. The MPLS LDP General Group and the MPLS LDP
Notifications Group should always be supported. The MPLS LDP ATM
Expires September 2000 [Page 5]
INTERNET-DRAFT MPLS LDP MIB March 2000
Group is specific to ATM and should be supported only if LDP is using
ATM. Likewise, the MPLS LDP Frame Relay group is specific to Frame
Relay and should be supported only if LDP is using Frame Relay.
3.5. The MPLS LDP General Group
This group contains information about the specific LDP Entities which
are associated with this agent. Each LSR must have one LDP Entity.
3.5.1. The Label Distribution Protocol's Entity Table
The LDP Entity Table provides a way to configure the LSR for using
LDP. There must be at least one LDP Entity for the LSR to support
LDP.
Each entry/row in this table represents a single LDP Entity.
3.5.2. Row Creation in the MplsLdpEntity and Associated Tables
It should be noted that special care should be taken if MIB objects
which are used in the MPLS LDP Session Initialization need to be
changed AFTER Session Initialization has occurred. For example,
currently there is no way to modify a Label Range once a session has
been established. Thus, in order to do this, the entire session with
the peer needs to be torn down. All information (LIB and FEC)
learned during this session needs to be removed from the MIB. Then
and only then is it save to modify a Label Range. After
modification, the LDP Entity will need to go through the Session
Initialization again, in order to communicate the new Label Ranges to
the Peer and establish new sessions.
Please see AdminStatus and RowStatus objects in these tables for more
details.
3.5.3. The Label Distribution Protocol's Entity ATM Objects
There exists two tables to configure LDP for using ATM. These tables
are the mplsLdpEntityAtmParmsTable and the
mplsLdpEntityConfAtmLabelRangeTable.
The mplsLdpEntityAtmParmsTable provides a way to configure
information which would be contained in the 'Optional Parameter'
portion of an LDP PDU Initialization Message.
The mplsLdpEntityConfAtmLabelRangeTable provides a way to configure
information which would be contained in the 'ATM Label Range
Expires September 2000 [Page 6]
INTERNET-DRAFT MPLS LDP MIB March 2000
Components' portion of an LDP PDU Intialization Message.
3.5.4. The Label Distribution Protocol's Entity Frame Relay Objects
There exists two tables to configure LDP for using Frame Relay.
These tables are the mplsLdpEntityFrameRelayParmsTable and the
mplsLdpEntityConfFrLabelRangeTable.
The mplsLdpEntityFrameRelayParmsTable provides a way to configure
information which would be contained in the 'Optional Parameter'
portion of an LDP PDU Initialization Message.
The mplsLdpEntityConfFrLabelRangeTable provides a way to configure
information which would be contained in the portion of an LDP PDU
Intialization Message.
3.5.5. The Label Distribution Protocol's Entity Statistics Table
The LDP Entity Statistics Table will maintain counters related to an
LDP Entity. This Table should be a read-only table which contains
statistical information.
Each row in this table will be related to a single LDP Entity.
3.5.6. The LDP Entity Peer Table
The LDP Entity Peer Table is a read-only table which contains
information about LDP Peers known to LDP Entities. A row in this
table is related to one or more rows in the Hello Adjacency Table and
one or more rows in the Session Table. The information in the
Entity-Peer table is relevant to a Peer but is not the same
information that is used by the actual session(s) which are related
to this Peer. For example, the PathLimit information is gleaned from
the session initialization phase but is not part of a session if
there is a mismatch. In the event of a mismatch, then the session
will use the PathLimit set by the Entity (and not the Peer).
A separate table allows for a more comprehensive and coherent MIB
model.
3.5.7. The LDP Hello Adjacencies Table
This is a table of all adjacencies between all LPD Entities and all
LDP Peers. A Session may have one or more adjacencies.
Expires September 2000 [Page 7]
INTERNET-DRAFT MPLS LDP MIB March 2000
3.5.8. The LDP Session Table
The LDP Session Table is a read-only table. Each entry in this table
represents a single session between an LDP Entity and a Peer.
3.5.9. The LDP ATM Session Table
The MPLS LDP ATM Session Table is a read-only table which contains
session information specific to ATM.
3.5.10. The LDP Frame Relay Session Table
The MPLS LDP Frame Relay Session Table is a read-only table which
contains session information specific to Frame Relay.
3.5.11. The LDP Session Statistics Table
The MPLS LDP Session Stats Table is a read-only table which contains
statistical information on sessions.
3.5.12. The LDP Session Peer Address Table
The MPLS LDP Session Peer Address Table is a table which 'extends'
the mplsLdpSessionTable. This table is a read-only table which
stores Addresses learned after session initialization via "Address
Message" advertisement.
3.5.13. The LDP Label Information Base (LIB) Table
The MPLS LDP LIB Table is a read-only table which contains
information stored in the LIB. This table is indexed by a unique
number which could be used to represent the LSP segment related to
this LIB entry. The Lsp number corresponds to a FEC entry in the FEC
Table which is described next.
3.5.14. The LDP FEC Table
The FEC Table is a read-only table which contains FEC (Forwarding
Equivalence Class) information. Each entry/row represents a single
FEC Element.
Expires September 2000 [Page 8]
INTERNET-DRAFT MPLS LDP MIB March 2000
3.6. The LDP Notifications Group
3.6.1. LDP Notifications
Currently, there are two notifications:
mplsLdpFailedInitSessionThresholdExceeded and
mplsLdpPathVectorLimitMismatch.
mplsLdpFailedInitSessionThresholdExceeded is sent when the
'mplsLdpEntityFailedInitSessionThreshold' is exceeded. This
notification should indicate to the operator that there may be a
misconfigured mplsLdpEntityEntry because the session associated with
this Entity is not being established, and the Entity keeps trying to
establish the session. A side effect of this situation is that a row
in the mplsLdpSessionTable may not be reaching the operational state
as indicated by the
The mplsLdpPathVectorLimitMismatch notification is sent when the
Entity's Path Vector Limit and the Peer's Path Vector Limit do not
agree. In this situation a session could still be established
between the entity and the peer, using the Entity's Path Vector
Limit. For further details, please see Section 3.5.3 of the LDP
Specification [18].
4. MPLS Label Distribution Protocol MIB Definitions
MPLS-LDP-MIB DEFINITIONS ::= BEGIN
IMPORTS
OBJECT-TYPE, MODULE-IDENTITY, NOTIFICATION-TYPE,
experimental,
Integer32, Counter32, Unsigned32
FROM SNMPv2-SMI
MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP
FROM SNMPv2-CONF
TEXTUAL-CONVENTION, RowStatus, TimeInterval, TruthValue,
TimeStamp, StorageType, RowPointer
FROM SNMPv2-TC
InterfaceIndex, InterfaceIndexOrZero
FROM IF-MIB
-- AtmInterfaceType,
AtmVcIdentifier, AtmVpIdentifier
FROM ATM-TC-MIB
AddressFamilyNumbers
FROM IANA-ADDRESS-FAMILY-NUMBERS-MIB
;
Expires September 2000 [Page 9]
INTERNET-DRAFT MPLS LDP MIB March 2000
mplsLdpMIB MODULE-IDENTITY
LAST-UPDATED "200003041200Z" -- March 4, 2000
ORGANIZATION "Multiprotocol Label Switching (mpls)
Working Group"
CONTACT-INFO
"Joan Cucchiara (jcucchiara@brixnet.com)
Brix Networks
Hans Sjostrand (hans.sjostrand@etx.ericsson.se)
Ericsson
James V. Luciani (jluciani@tollbridgetech.com)
TollBridge Technologies"
DESCRIPTION
"This MIB contains managed object definitions for the
Multiprotocol Label Switching, Label Distribution
Protocol, LDP, as defined in draft-ietf-mpls-ldp-06.txt."
::= { experimental XXXX} -- to be assigned
--****************************************************************
-- MPLS LDP Textual Conventions
--****************************************************************
--
MplsLsrIdentifier ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The Label Switch Router (LSR) identifier
is the first 4 bytes or the IP Address component
of the Label Distribution Protocol (LDP) identifier."
SYNTAX OCTET STRING (SIZE (4))
--
-- A similar TC is also used in RFC2677.txt, perhaps
-- this should be made general and not MPLS specific.
--
MplsLdpGenAddr ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The value of an network layer or data link
layer address."
SYNTAX OCTET STRING (SIZE (0..64))
-- following label is taken from the
-- draft-ietf-mpls-lsr-mib-01.txt
-- It is reproduced here and modified to reflect
-- the Frame Relay Forum's
-- recent decision to drop 17-bit DLCI support,
-- and other modifications. Also, added
-- reference 3. to REFERENCE clause.
Expires September 2000 [Page 10]
INTERNET-DRAFT MPLS LDP MIB March 2000
MplsLabel ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Represents an MPLS label. The label contents are
are specific to the label being represented.
The label carried in an MPLS shim header
(for LDP, the Generic Label) is a 20-bit number
represented by 4 octets. Bits 0-19 contain a
label or a reserved label value. Bits 20-31 MUST
be zero.
The frame relay label can be either 10-bits or
23-bits depending on the DLCI field size and the
upper 22-bits or upper 9-bits must be zero, respectively.
For an ATM label the lower 16-bits represents the VCI,
the next 8-bits represents the VPI and the remaining
bits MUST be zero."
REFERENCE
"1. 'MPLS Label Stack Encoding', Rosen et al., draft-
ietf-mpls-label-encaps-07.txt, September 1999.
2. 'Use of Label Switching on Frame Relay Networks',
Conta et al., draft-ietf-mpls-fr-03.txt,
November 1998.
3. 'MPLS using LDP and ATM VC Switching', Davie et al.,
draft-ietf-mpls-atm-02.txt, April 1999."
SYNTAX Integer32
MplsLdpIdentifier ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The LDP identifier is a six octet quantity
which is used to identify an Label Switch Router
(LSR) label space.
The first four octets encode an IP address
assigned to the LSR, and the last two octets
identify a specific label space within the LSR."
SYNTAX OCTET STRING (SIZE (6))
MplsLdpLabelTypes ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The Layer 2 label types which are defined for
MPLS LDP are generic(1), atm(2), or frameRelay(3)."
SYNTAX INTEGER {
generic(1),
Expires September 2000 [Page 11]
INTERNET-DRAFT MPLS LDP MIB March 2000
atm(2),
frameRelay(3)
}
-- Top-level structure of the MIB (the following is proposed)
mpls OBJECT IDENTIFIER ::= { mplsProtocols }
mplsProtocols OBJECT IDENTIFIER ::= { mplsLdpObjects }
-- under mplsProtocols will be LDP, CR-LDP,
-- and other MPLS "Protocols".
mplsLdpObjects OBJECT IDENTIFIER ::= { mplsLdpMIB 1 }
mplsLdpNotifications OBJECT IDENTIFIER ::= { mplsLdpMIB 2 }
mplsLdpConformance OBJECT IDENTIFIER ::= { mplsLdpMIB 3 }
--****************************************************************
-- MPLS LDP Objects
--****************************************************************
mplsLdpLsrObjects OBJECT IDENTIFIER ::= { mplsLdpObjects 1 }
mplsLdpEntityObjects OBJECT IDENTIFIER ::= { mplsLdpObjects 2 }
--
-- The MPLS Label Distribution Protocol's
-- Label Switch Router Objects
--
mplsLdpLsrId OBJECT-TYPE
SYNTAX MplsLsrIdentifier
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The LSR's Identifier."
::= { mplsLdpLsrObjects 1 }
mplsLdpLsrLabelRetentionMode OBJECT-TYPE
SYNTAX INTEGER {
conservative(1),
liberal(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The LSR can be configured to use either
conservative or liberal label retention mode.
If the value of this object is conservative(1)
then advertized label mappings are retained
only if they will be used to forward packets,
Expires September 2000 [Page 12]
INTERNET-DRAFT MPLS LDP MIB March 2000
i.e. if label came from a valid next hop.
If the value of this object is liberal(2)
then all advertized label mappings are retained
whether they are from a valid next hop or not."
::= { mplsLdpLsrObjects 2 }
mplsLdpLsrLoopDetectionCapable OBJECT-TYPE
SYNTAX INTEGER {
none(1),
other(2),
hopCount(3),
pathVector(4),
hopCountAndPathVector(5)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A indication of whether this LSR supports
loop detection.
none(1) -- Loop Detection is not supported
on this LSR.
other(2) -- Loop Detection is supported but
by a method other than those
listed below.
hopCount(3) -- Loop Detection is supported by
Hop Count only.
pathVector(4) -- Loop Detection is supported by
Path Vector only.
hopCountAndPathVector(5) -- Loop Detection is
supported by both Hop Count
And Path Vector.
Since Loop Detection is determined during
Session Initialization, an individual session
may not be running with loop detection. This
object simply gives an indication of whether or not the
LSR has the ability to support Loop Detection and
which types."
::= { mplsLdpLsrObjects 3 }
--
-- The MPLS Label Distribution Protocol Entity Objects
--
Expires September 2000 [Page 13]
INTERNET-DRAFT MPLS LDP MIB March 2000
mplsLdpEntityIndexNext OBJECT-TYPE
SYNTAX Unsigned32 (0..4294967295)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains an appropriate value to
be used for mplsLdpEntityIndex when creating
entries in the mplsLdpEntityTable. The value
0 indicates that no unassigned entries are
available. To obtain the mplsLdpEntityIndex
value for a new entry, the manager issues a
management protocol retrieval operation to obtain
the current value of this object. After each
retrieval, the agent should modify the value to
the next unassigned index."
::= { mplsLdpEntityObjects 1 }
mplsLdpEntityTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsLdpEntityEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains information about the
MPLS Label Distribution Protocol Entities which
exist on this Label Switch Router (LSR)."
::= { mplsLdpEntityObjects 2 }
mplsLdpEntityEntry OBJECT-TYPE
SYNTAX MplsLdpEntityEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table represents an LDP entity.
An entry can be created by a network administrator
or by an SNMP agent as instructed by LDP."
INDEX { mplsLdpEntityLdpId, mplsLdpEntityIndex }
::= { mplsLdpEntityTable 1 }
MplsLdpEntityEntry ::= SEQUENCE {
mplsLdpEntityLdpId MplsLdpIdentifier,
mplsLdpEntityIndex Unsigned32,
mplsLdpEntityProtocolVersion Integer32,
mplsLdpEntityAdminStatus INTEGER,
mplsLdpEntityOperStatus INTEGER,
mplsLdpEntityWellKnownDiscoveryPort Unsigned32,
mplsLdpEntityMaxPduLength Unsigned32,
mplsLdpEntityKeepAliveHoldTimer Integer32,
mplsLdpEntityHelloHoldTimer Integer32,
mplsLdpEntityFailedInitSessionTrapEnable INTEGER,
Expires September 2000 [Page 14]
INTERNET-DRAFT MPLS LDP MIB March 2000
mplsLdpEntityFailedInitSessionThreshold Integer32,
mplsLdpEntityLabelDistributionMethod INTEGER,
mplsLdpEntityPVLimitMismatchTrapEnable INTEGER,
mplsLdpEntityPathVectorLimit Integer32,
mplsLdpEntityHopCountLoopDetection INTEGER,
mplsLdpEntityHopCount Unsigned32,
mplsLdpEntityTargetedPeer TruthValue,
mplsLdpEntityTargetedPeerAddrType AddressFamilyNumbers,
mplsLdpEntityTargetedPeerAddr MplsLdpGenAddr,
mplsLdpEntityOptionalParameters MplsLdpLabelTypes,
mplsLdpEntityDiscontinuityTime TimeStamp,
mplsLdpEntityStorageType StorageType,
mplsLdpEntityRowStatus RowStatus
}
mplsLdpEntityLdpId OBJECT-TYPE
SYNTAX MplsLdpIdentifier
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The LDP identifier.
The first four octets encode an IP address
assigned to the LSR, and the last two octets
identify a specific label space within the
LSR."
REFERENCE
"LDP Specification, Section on LDP Identifiers."
::= { mplsLdpEntityEntry 1 }
mplsLdpEntityIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This index is used as a secondary index to uniquely
identify this row. Before creating a row in this table,
the 'mplsLdpEntityIndexNext' object should be retrieved.
That value should be used for the value of this index
when creating a row in this table. (NOTE: if a value
of zero (0) is retrieved, that indicates that no rows
can be created in this table at this time."
::= { mplsLdpEntityEntry 2 }
mplsLdpEntityProtocolVersion OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
Expires September 2000 [Page 15]
INTERNET-DRAFT MPLS LDP MIB March 2000
"The version number of the protocol. The value of 0 on a
read indicates that the version of the protocol is unknown.
Otherwise, the value of this object represents the version
of the LDP protocol."
::= { mplsLdpEntityEntry 3 }
mplsLdpEntityAdminStatus OBJECT-TYPE
SYNTAX INTEGER {
enable(1),
disable(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The administrative status of this LDP Entity.
If this object is changed from 'enable' to 'disable'
and this entity has already attempted to establish
contact with a Peer (which implies that the
'mplsLdpEntityRowStatus' object has been set to
'active'), then all contact with that
Peer is lost and all information from that Peer
needs to be removed from the MIB.
At this point the user is able to change values
which are related to this entity.
When the admin status is set back to 'up', then
this Entity will attempt to establish new sessions
with the Peer."
DEFVAL { enable }
::= { mplsLdpEntityEntry 4 }
mplsLdpEntityOperStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(0),
enabled(1),
disabled(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The operational status of this LDP Entity."
::= { mplsLdpEntityEntry 5 }
mplsLdpEntityWellKnownDiscoveryPort OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
Expires September 2000 [Page 16]
INTERNET-DRAFT MPLS LDP MIB March 2000
"The well known LDP Discovery Port."
::= { mplsLdpEntityEntry 6 }
mplsLdpEntityMaxPduLength OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum PDU Length that is sent in
the Common Session Parameters of an Initialization
Message. A value of 255 or less specifies the
default maximum length of 4096 octets."
REFERENCE
"See Section on the 'Initialization Message' in the
LDP Specification."
::= { mplsLdpEntityEntry 7 }
mplsLdpEntityKeepAliveHoldTimer OBJECT-TYPE
SYNTAX Integer32 (1..65535)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The two octet value which is the proposed keep alive hold
timer for this LDP Entity."
::= { mplsLdpEntityEntry 8 }
mplsLdpEntityHelloHoldTimer OBJECT-TYPE
SYNTAX Integer32 (0..65535)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The two octet value which is the proposed Hello hold
timer for this LDP Entity. A value of 0 means use the
default, which is 15 seconds for Link Hellos and 45
seconds for Targeted Hellos. A value of 65535 means
infinite."
DEFVAL { 0 }
::= { mplsLdpEntityEntry 9 }
mplsLdpEntityFailedInitSessionTrapEnable OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Indicates whether the
Expires September 2000 [Page 17]
INTERNET-DRAFT MPLS LDP MIB March 2000
'mplsLdpFailedInitSessionThresholdExceeded'
trap should be generated.
If the value of this object is 'enabled(1)'
then the trap will generated. If the value
of this object is 'disabled(2)' then the
trap will not be generated. The DEFVAL
is set to 'enabled(1)'."
DEFVAL { enabled }
::= { mplsLdpEntityEntry 10 }
mplsLdpEntityFailedInitSessionThreshold OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"When attempting to establish a session with a
given Peer, the given LDP Entity should
send out the SNMP notification,
'mplsLdpFailedInitSessionThresholdExceeded', when
the number of Session Initialization messages sent
exceeds this threshold.
A value of 0 (zero) for this object
indicates that the threshold is infinity, and
the SNMP notification will never be sent
when the value of this object is 0 (zero)."
::= { mplsLdpEntityEntry 11 }
mplsLdpEntityLabelDistributionMethod OBJECT-TYPE
SYNTAX INTEGER {
downstreamOnDemand(1),
downstreamUnsolicited(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"For any given LDP session, the method of
label distribution must be specified."
::= { mplsLdpEntityEntry 12 }
mplsLdpEntityPVLimitMismatchTrapEnable OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
MAX-ACCESS read-create
STATUS current
Expires September 2000 [Page 18]
INTERNET-DRAFT MPLS LDP MIB March 2000
DESCRIPTION
"Indicates whether the 'mplsLdpPathVectorLimitMismatch'
trap should be generated.
If the value of this object is 'enabled(1)'
then the trap will generated. If the value
of this object is 'disabled(2)' then the
trap will not be generated. The DEFVAL
is set to 'enabled(1)'."
DEFVAL { enabled }
::= { mplsLdpEntityEntry 13 }
mplsLdpEntityPathVectorLimit OBJECT-TYPE
SYNTAX Integer32 (0..255)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"If the value of this object is 0 (zero) then
Loop Dection for Path Vectors is disabled.
Otherwise, if this object has a value greater than
zero, then Loop Dection for Path Vectors is enabled,
and the Path Vector Limit is this value.
Also, the value of the object,
'mplsLdpLsrLoopDetectionCapable', must be set to
either 'pathVector(4)' or 'hopCountAndPathVector(5)',
if this object has a value greater than 0 (zero)."
::= { mplsLdpEntityEntry 14 }
mplsLdpEntityHopCountLoopDetection OBJECT-TYPE
SYNTAX INTEGER {
disabled(0),
enabled(1)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An indication of whether loop detection based
on hop count is disabled or enabled for this
Entity. If this object has the value of
'disabled(0)', then loop detection using
hop counts is disabled.
Otherwise, if this object has a value of 'enabled(1)',
then loop detection based on hop counts is enabled.
Also, the value of the object,
'mplsLdpLsrLoopDetectionCapable', must have the value
of either: 'hopCount(3)' or 'hopCountAndPathVector(5)'."
Expires September 2000 [Page 19]
INTERNET-DRAFT MPLS LDP MIB March 2000
::= { mplsLdpEntityEntry 15 }
mplsLdpEntityHopCount OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"If the value of 'mplsLdpEntityHopCountLoopDetection'
for this entry is 'enabled(1)', then this object
represents the initial Hop Count for this Entity.
If the value of 'mplsLdpEntityHopCountLoopDetection'
is 'disabled(0)', then the value of this object is
undefined."
::= { mplsLdpEntityEntry 16 }
mplsLdpEntityTargetedPeer OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"If this LDP entity uses targeted peer then set
this to true."
DEFVAL { false }
::= { mplsLdpEntityEntry 17 }
mplsLdpEntityTargetedPeerAddrType OBJECT-TYPE
SYNTAX AddressFamilyNumbers
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The type of the internetwork layer address used for
the Extended Discovery. This object indicates how
the value of mplsLdpEntityTargetedPeerAddr is to
be interpreted."
::= { mplsLdpEntityEntry 18 }
mplsLdpEntityTargetedPeerAddr OBJECT-TYPE
SYNTAX MplsLdpGenAddr
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of the internetwork layer address used for
the Extended Discovery."
::= { mplsLdpEntityEntry 19 }
mplsLdpEntityOptionalParameters OBJECT-TYPE
SYNTAX MplsLdpLabelTypes
MAX-ACCESS read-create
Expires September 2000 [Page 20]
INTERNET-DRAFT MPLS LDP MIB March 2000
STATUS current
DESCRIPTION
"Specifies the optional parameters for the LDP
Initialization Message. If the value is generic(1)
then no optional parameters will be sent in
the LDP Initialization message associated with
this Entity.
If the value is atmParameters(2) then
a row must be created in the mplsLdpEntityAtmParms
Table, which corresponds to this entry.
If the value is frameRelayParameters(3) then
a row must be created in the mplsLdpEntityFrameRelayParms
Table, which corresponds to this entry."
::= { mplsLdpEntityEntry 20 }
mplsLdpEntityDiscontinuityTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime on the most recent occasion
at which any one or more of this entity's counters
suffered a discontinuity. The relevant counters are the
specific instances associated with this entity of
any Counter32, or Counter64 object contained
in the 'mplsLdpEntityStatsTable'. If no such
discontinuities have occurred since the last
re-initialization of the local management
subsytem, then this object contains a zero
value."
::= { mplsLdpEntityEntry 21 }
mplsLdpEntityStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The storage type for this entry."
::= { mplsLdpEntityEntry 22 }
mplsLdpEntityRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
Expires September 2000 [Page 21]
INTERNET-DRAFT MPLS LDP MIB March 2000
"An object that allows entries in this table to
be created and deleted using the
RowStatus convention.
Once the 'mplsLdpEntityAdminStatus' object has
the value of 'up' and this object has the value
of 'active' then the Entity will atttempt to
contact an LDP Peer. If the value of this object
is changed to 'notInService', then the Entity looses
contact with the LDP Peer and all information related
to that Peer must be removed from the MIB. This has
the same effect as changing 'mplsLdpEntityAdminStatus'
from 'enable' to 'disable'.
When this object is set to 'active' and the value of
the 'mplsLdpEntityAdminStatus' is 'enable' then
this Entity will attempt to contact the Peer and
establish new sessions."
::= { mplsLdpEntityEntry 23 }
--
-- Ldp Entity Objects for Generic Labels
--
mplsLdpEntityGenericObjects OBJECT IDENTIFIER ::=
{ mplsLdpEntityObjects 3 }
mplsLdpEntityConfGenericTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsLdpEntityConfGenericEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides a way to configure Generic Labels
associated with LDP entities on the LSR."
::= { mplsLdpEntityGenericObjects 1 }
mplsLdpEntityConfGenericEntry OBJECT-TYPE
SYNTAX MplsLdpEntityConfGenericEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table provides a way to configure
a 'Generic Label' for LDP.
An entry in the 'mplsLdpEntityTable' will only have
associated entries in this Table if Generic Labels
are configured for a specific 'mplsLdpEntityEntry'.
Thus, not every 'mplsLdpEntityEntry' will have
associated entries in this table.
Expires September 2000 [Page 22]
INTERNET-DRAFT MPLS LDP MIB March 2000
The InterfaceIndex value for a Generic Label is
from the 'ifLayer' where the label is created. Likewise,
the ifType of the interface is the 'ifLayer' where the
label is created. For example, if an implementation
creates the generic label at the ifLayer which
has the 'ifType' of 'mpls', then the
'mplsLdpConfGenericIfIndexOrZero' object
should be set to the value of the InterfaceIndex
for this 'ifLayer'.
If the value of 'mplsLdpConfGenericIfIndexOrZero' is zero
then the InterfaceIndex value of this object is not known.
If this Generic Label is used, i.e. a session has been
established successfully and data is forwarded using this
label, then the value of the
'mplsLdpConfGenericIfIndexOrZero' object MUST be
updated by the network management entity
(e.g. SNMP agent) to reflect the InterfaceIndex
value for the 'ifLayer' that created the Generic Label.
To summarize, not all implementations may assign ifIndices
at a label's creation time, thus, an ifIndex value
may not be known, until a subsequent time. However,
once that ifIndex value is known, the
'mplsLdpConfGenericIfIndexOrZero' object
should be changed to reflect the ifIndex value."
INDEX { mplsLdpEntityLdpId,
mplsLdpEntityIndex,
mplsLdpConfGenericIndex
}
::= { mplsLdpEntityConfGenericTable 1 }
MplsLdpEntityConfGenericEntry ::= SEQUENCE {
mplsLdpConfGenericIndex Unsigned32,
mplsLdpConfGenericIfIndexOrZero InterfaceIndexOrZero,
mplsLdpConfGenericLabel Unsigned32,
mplsLdpConfGenericStorageType StorageType,
mplsLdpConfGenericRowStatus RowStatus
}
mplsLdpConfGenericIndex OBJECT-TYPE
SYNTAX Unsigned32(1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This index is used to distinguish between multiple
Generic Labels configured for the same LDP Entity."
::= { mplsLdpEntityConfGenericEntry 1 }
Expires September 2000 [Page 23]
INTERNET-DRAFT MPLS LDP MIB March 2000
mplsLdpConfGenericIfIndexOrZero OBJECT-TYPE
SYNTAX InterfaceIndexOrZero
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This value represents either the InterfaceIndex of
the 'ifLayer' where this Generic Label was created, or
0 (zero). The value of zero means that the InterfaceIndex
is not known. For example, if the InterfaceIndex is
created subsequent to the Generic Label's creation, then
it would not be known. However, if the InterfaceIndex
is known, then it must be represented by this value.
If an InterfaceIndex becomes known, then the
network management entity (e.g. SNMP agent) responsible
for this object MUST change the value from 0 (zero) to the
value of the InterfaceIndex. If this Generic Label is
being used in forwarding data, then the value of this
object MUST be the InterfaceIndex."
::= { mplsLdpEntityConfGenericEntry 2 }
mplsLdpConfGenericLabel OBJECT-TYPE
SYNTAX Unsigned32(0..1048575)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of this object represents the Generic Label
used in the Generic Label TLV."
REFERENCE
"Generic Label TLV Section of the LDP Specification."
::= { mplsLdpEntityConfGenericEntry 3 }
mplsLdpConfGenericStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The storage type for this entry."
::= { mplsLdpEntityConfGenericEntry 4 }
mplsLdpConfGenericRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An object that allows entries in this table to
be created and deleted using the
RowStatus convention.
NOTE: This RowStatus object should
Expires September 2000 [Page 24]
INTERNET-DRAFT MPLS LDP MIB March 2000
have the same value of the 'mplsLdpEntityRowStatus'
related to this entry."
::= { mplsLdpEntityConfGenericEntry 5 }
--
-- Ldp Entity Objects for ATM
--
mplsLdpEntityAtmObjects OBJECT IDENTIFIER ::=
{ mplsLdpEntityObjects 4 }
mplsLdpEntityAtmParmsTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsLdpEntityAtmParmsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains information about the
ATM specific information which could be used
in the 'Optional Parameters' and other ATM specific
information."
::= { mplsLdpEntityAtmObjects 1 }
mplsLdpEntityAtmParmsEntry OBJECT-TYPE
SYNTAX MplsLdpEntityAtmParmsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table represents the ATM parameters
and ATM information for this LDP entity."
INDEX { mplsLdpEntityLdpId,
mplsLdpEntityIndex
}
::= { mplsLdpEntityAtmParmsTable 1 }
MplsLdpEntityAtmParmsEntry ::= SEQUENCE {
mplsLdpEntityAtmIfIndexOrZero InterfaceIndexOrZero,
mplsLdpEntityAtmMergeCap INTEGER,
mplsLdpEntityAtmLabelRangeComponents Unsigned32,
mplsLdpEntityAtmVcDirectionality INTEGER,
mplsLdpEntityAtmLsrConnectivity INTEGER,
mplsLdpEntityDefaultControlVpi AtmVpIdentifier,
mplsLdpEntityDefaultControlVci AtmVcIdentifier,
mplsLdpEntityUnlabTrafVpi AtmVpIdentifier,
mplsLdpEntityUnlabTrafVci AtmVcIdentifier,
mplsLdpEntityAtmStorageType StorageType,
mplsLdpEntityAtmRowStatus RowStatus
}
Expires September 2000 [Page 25]
INTERNET-DRAFT MPLS LDP MIB March 2000
mplsLdpEntityAtmIfIndexOrZero OBJECT-TYPE
SYNTAX InterfaceIndexOrZero
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This value represents either the InterfaceIndex of
the 'ifLayer' where the ATM Labels 'owned' by this
entry were created, or 0 (zero). The value of zero
means that the InterfaceIndex is not known. For example,
if the InterfaceIndex is created subsequent to the
ATM Label's creation, then it would not be known.
However, if the InterfaceIndex is known, then it must
be represented by this value.
If an InterfaceIndex becomes known, then the
network management entity (e.g. SNMP agent) responsible
for this object MUST change the value from 0 (zero) to the
value of the InterfaceIndex. If an ATM Label is
being used in forwarding data, then the value of this
object MUST be the InterfaceIndex."
::= { mplsLdpEntityAtmParmsEntry 1 }
mplsLdpEntityAtmMergeCap OBJECT-TYPE
SYNTAX INTEGER {
notSupported(0),
vpMerge(1),
vcMerge(2),
vpAndVcMerge(3)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Denotes the Merge Capability of this Entity."
::= { mplsLdpEntityAtmParmsEntry 2 }
mplsLdpEntityAtmLabelRangeComponents OBJECT-TYPE
SYNTAX Unsigned32 (1..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Number of LabelRange Components in the Initialization
message. This also represents the number of entries
in the mplsLdpLabelRangeComponentsTable which correspond
to this entry."
::= { mplsLdpEntityAtmParmsEntry 3 }
mplsLdpEntityAtmVcDirectionality OBJECT-TYPE
SYNTAX INTEGER {
bidirectional(0),
Expires September 2000 [Page 26]
INTERNET-DRAFT MPLS LDP MIB March 2000
unidirectional(1)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"If the value of this object is 'bidirectional(0)',
a given VCI, within a given VPI, is used as a
label for both directions independently.
If the value of this object is 'unidirectional(1)',
a given VCI within a VPI designates one direction."
::= { mplsLdpEntityAtmParmsEntry 4 }
mplsLdpEntityAtmLsrConnectivity OBJECT-TYPE
SYNTAX INTEGER {
direct(1),
indirect(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The peer LSR may be connected indirectly by means of an
ATM VP so that the VPI values may be different on either
endpoint so the label MUST be encoded entirely within the
VCI field."
REFERENCE
"draft-ietf-mpls-atm-02.txt, Section 7"
DEFVAL { direct }
::= { mplsLdpEntityAtmParmsEntry 5 }
mplsLdpEntityDefaultControlVpi OBJECT-TYPE
SYNTAX AtmVpIdentifier
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The default VPI value for the non-MPLS connection. The
default value of this is 0 (zero) but other values may
be configured. This object allows a different value
to be configured."
REFERENCE
"draft-ietf-mpls-atm-02.txt, Section 7.1"
DEFVAL
{ 0 }
::= { mplsLdpEntityAtmParmsEntry 6 }
mplsLdpEntityDefaultControlVci OBJECT-TYPE
SYNTAX AtmVcIdentifier
MAX-ACCESS read-create
STATUS current
DESCRIPTION
Expires September 2000 [Page 27]
INTERNET-DRAFT MPLS LDP MIB March 2000
"The Default VCI value for a non-MPLS connection. The
default value of this is 32 but other values may be
configured. This object allows a different value to
be configured."
REFERENCE
"draft-ietf-mpls-atm-02.txt, Section 7.1"
DEFVAL
{ 32 }
::= { mplsLdpEntityAtmParmsEntry 7 }
mplsLdpEntityUnlabTrafVpi OBJECT-TYPE
SYNTAX AtmVpIdentifier
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"VPI value of the VCC supporting unlabelled traffic. This
non-MPLS connection is used to carry unlabelled (IP)
packets."
DEFVAL { 0 }
::= { mplsLdpEntityAtmParmsEntry 8 }
mplsLdpEntityUnlabTrafVci OBJECT-TYPE
SYNTAX AtmVcIdentifier
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"VCI value of the VCC supporting unlabelled traffic.
This non-MPLS connection is used to carry unlabelled (IP)
packets."
DEFVAL { 32 }
::= { mplsLdpEntityAtmParmsEntry 9 }
mplsLdpEntityAtmStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The storage type for this entry."
::= { mplsLdpEntityAtmParmsEntry 10 }
mplsLdpEntityAtmRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An object that allows entries in this table to
be created and deleted using the
RowStatus convention.
NOTE: This RowStatus object should
Expires September 2000 [Page 28]
INTERNET-DRAFT MPLS LDP MIB March 2000
have the same value of the 'mplsLdpEntityRowStatus'
related to this entry."
::= { mplsLdpEntityAtmParmsEntry 11 }
--
-- The MPLS LDP Entity Configurable ATM Label Range Table
--
mplsLdpEntityConfAtmLabelRangeTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsLdpEntityConfAtmLabelRangeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The MPLS LDP Entity Configurable ATM Label Range Table.
The purpose of this table is to provide a mechanism
for specifying a contiguous range of vpi's
with a contiguous range of vci's, or a 'label range'
for LDP Entities.
LDP Entities which use ATM must have at least one
entry in this table."
::= { mplsLdpEntityAtmObjects 2 }
mplsLdpEntityConfAtmLabelRangeEntry OBJECT-TYPE
SYNTAX MplsLdpEntityConfAtmLabelRangeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A row in the LDP Entity Configurable ATM Label
Range Table. One entry in this table contains
information on a single range of labels
represented by the configured Upper and Lower
Bounds VPI/VCI pairs. These are the same
data used in the Initialization Message.
NOTE: The ranges for a specific LDP Entity
are UNIQUE and non-overlapping. For example,
for a specific LDP Entity index, there could
be one entry having ConfLowerBound vpi/vci == 0/32, and
ConfUpperBound vpi/vci == 0/100, and a second entry
for this same interface with ConfLowerBound
vpi/vci == 0/101 and ConfUpperBound vpi/vci == 0/200.
However, there could not be a third entry with
ConfLowerBound vpi/vci == 0/200 and
ConfUpperBound vpi/vci == 0/300 because this label
range overlaps with the second entry (i.e. both
entries now have 0/200).
A row will not be created unless a unique and
non-overlapping range is specified. Thus, row
Expires September 2000 [Page 29]
INTERNET-DRAFT MPLS LDP MIB March 2000
creation implies a one-shot row creation of
LDP EntityID and ConfLowerBound vpi/vci and
ConfUpperBound vpi/vci. At least one label
range entry for a specific LDP Entity MUST
include the default VPI/VCI values denoted
in the LDP Entity Table."
INDEX { mplsLdpEntityLdpId,
mplsLdpEntityIndex,
mplsLdpEntityConfAtmLabelRangeMinimumVpi,
mplsLdpEntityConfAtmLabelRangeMinimumVci
}
::= { mplsLdpEntityConfAtmLabelRangeTable 1 }
MplsLdpEntityConfAtmLabelRangeEntry ::= SEQUENCE {
mplsLdpEntityConfAtmLabelRangeMinimumVpi AtmVpIdentifier,
mplsLdpEntityConfAtmLabelRangeMinimumVci AtmVcIdentifier,
mplsLdpEntityConfAtmLabelRangeMaximumVpi AtmVpIdentifier,
mplsLdpEntityConfAtmLabelRangeMaximumVci AtmVcIdentifier,
mplsLdpEntityConfAtmLabelRangeStorageType StorageType,
mplsLdpEntityConfAtmLabelRangeRowStatus RowStatus
}
mplsLdpEntityConfAtmLabelRangeMinimumVpi OBJECT-TYPE
SYNTAX AtmVpIdentifier
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The minimum VPI number configured for this range."
::= { mplsLdpEntityConfAtmLabelRangeEntry 1 }
mplsLdpEntityConfAtmLabelRangeMinimumVci OBJECT-TYPE
SYNTAX AtmVcIdentifier
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The minimum VCI number configured for this range."
::= { mplsLdpEntityConfAtmLabelRangeEntry 2 }
mplsLdpEntityConfAtmLabelRangeMaximumVpi OBJECT-TYPE
SYNTAX AtmVpIdentifier
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum VPI number configured for this range."
::= { mplsLdpEntityConfAtmLabelRangeEntry 3 }
mplsLdpEntityConfAtmLabelRangeMaximumVci OBJECT-TYPE
SYNTAX AtmVcIdentifier
MAX-ACCESS read-create
STATUS current
Expires September 2000 [Page 30]
INTERNET-DRAFT MPLS LDP MIB March 2000
DESCRIPTION
"The maximum VCI number configured for this range."
::= { mplsLdpEntityConfAtmLabelRangeEntry 4 }
mplsLdpEntityConfAtmLabelRangeStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The storage type for this entry."
::= { mplsLdpEntityConfAtmLabelRangeEntry 5 }
mplsLdpEntityConfAtmLabelRangeRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An object that allows entries in this
table to be created and deleted using
the RowStatus convention.
There must exist at least one entry in this
table for every LDP Entity that has
'mplsLdpEntityOptionalParameters' object with
a value of 'atmSessionParameters'.
NOTE: This RowStatus object should
have the same value of the 'mplsLdpEntityRowStatus'
related to this entry."
::= { mplsLdpEntityConfAtmLabelRangeEntry 6 }
--
-- Ldp Entity Objects for Frame Relay
--
mplsLdpEntityFrameRelayObjects OBJECT IDENTIFIER ::=
{ mplsLdpEntityObjects 5 }
mplsLdpEntityFrameRelayParmsTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsLdpEntityFrameRelayParmsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains information about the
Optional Parameters to specify what this Entity is
going to specify for Frame Relay specific
LDP Intialization Messages."
::= { mplsLdpEntityFrameRelayObjects 1 }
Expires September 2000 [Page 31]
INTERNET-DRAFT MPLS LDP MIB March 2000
mplsLdpEntityFrameRelayParmsEntry OBJECT-TYPE
SYNTAX MplsLdpEntityFrameRelayParmsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table represents the Frame Relay
optional parameters associated with the LDP entity."
INDEX { mplsLdpEntityLdpId,
mplsLdpEntityIndex
}
::= { mplsLdpEntityFrameRelayParmsTable 1 }
MplsLdpEntityFrameRelayParmsEntry ::= SEQUENCE {
mplsLdpEntityFrIfIndexOrZero InterfaceIndexOrZero,
mplsLdpEntityFrMergeCap INTEGER,
mplsLdpEntityFrLabelRangeComponents Unsigned32,
mplsLdpEntityFrLen INTEGER,
mplsLdpEntityFrVcDirectionality INTEGER,
mplsLdpEntityFrParmsStorageType StorageType,
mplsLdpEntityFrParmsRowStatus RowStatus
}
mplsLdpEntityFrIfIndexOrZero OBJECT-TYPE
SYNTAX InterfaceIndexOrZero
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This value represents either the InterfaceIndex of
the 'ifLayer' where the Frame Relay Labels 'owned' by this
entry were created, or 0 (zero). The value of zero
means that the InterfaceIndex is not known. For example,
if the InterfaceIndex is created subsequent to the
Frame Relay Label's creation, then it would not be known.
However, if the InterfaceIndex is known, then it must
be represented by this value.
If an InterfaceIndex becomes known, then the
network management entity (e.g. SNMP agent) responsible
for this object MUST change the value from 0 (zero) to the
value of the InterfaceIndex. If an Frame Relay Label is
being used in forwarding data, then the value of this
object MUST be the InterfaceIndex."
::= { mplsLdpEntityFrameRelayParmsEntry 1 }
mplsLdpEntityFrMergeCap OBJECT-TYPE
SYNTAX INTEGER {
notSupported(0),
supported(1)
}
MAX-ACCESS read-create
Expires September 2000 [Page 32]
INTERNET-DRAFT MPLS LDP MIB March 2000
STATUS current
DESCRIPTION
"This represents whether or not Frame Relay merge
capability is supported."
::= { mplsLdpEntityFrameRelayParmsEntry 2 }
mplsLdpEntityFrLabelRangeComponents OBJECT-TYPE
SYNTAX Unsigned32 (1..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Number of LabelRange Components in the Initialization
message. This also represents the number of entries
in the mplsLdpEntityConfFrLabelRangeTable which correspond
to this entry."
::= { mplsLdpEntityFrameRelayParmsEntry 3 }
mplsLdpEntityFrLen OBJECT-TYPE
SYNTAX INTEGER {
tenDlciBits(0),
twentyThreeDlciBits(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the DLCI bits."
::= { mplsLdpEntityFrameRelayParmsEntry 4 }
mplsLdpEntityFrVcDirectionality OBJECT-TYPE
SYNTAX INTEGER {
bidirectional(0),
unidirection(1)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"If the value of this object is 'bidirectional(0)', then
the LSR supports the use of a given DLCI as a label for
both directions independently. If the value of
this object is 'unidirectional(1)', then the LSR
uses the given DLCI as a label in only one direction."
::= { mplsLdpEntityFrameRelayParmsEntry 5 }
mplsLdpEntityFrParmsStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The storage type for this entry."
Expires September 2000 [Page 33]
INTERNET-DRAFT MPLS LDP MIB March 2000
::= { mplsLdpEntityFrameRelayParmsEntry 6 }
mplsLdpEntityFrParmsRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An object that allows entries in this table to
be created and deleted using the
RowStatus convention.
NOTE: This RowStatus object should
have the same value of the 'mplsLdpEntityRowStatus'
related to this entry."
::= { mplsLdpEntityFrameRelayParmsEntry 7 }
--
-- Frame Relay Label Range Components
--
mplsLdpEntityConfFrLabelRangeTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsLdpEntityConfFrLabelRangeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains information about the
Optional Parameters to specify what this Entity is
going to specify for Frame Relay specific
LDP Intialization Messages."
::= { mplsLdpEntityFrameRelayObjects 2 }
mplsLdpEntityConfFrLabelRangeEntry OBJECT-TYPE
SYNTAX MplsLdpEntityConfFrLabelRangeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table represents the Frame Relay
optional parameters associated with the LDP entity."
INDEX { mplsLdpEntityLdpId,
mplsLdpEntityIndex,
mplsLdpConfFrMinimumDlci
}
::= { mplsLdpEntityConfFrLabelRangeTable 1 }
MplsLdpEntityConfFrLabelRangeEntry ::= SEQUENCE {
mplsLdpConfFrMinimumDlci Integer32,
mplsLdpConfFrMaximumDlci Integer32,
mplsLdpConfFrStorageType StorageType,
Expires September 2000 [Page 34]
INTERNET-DRAFT MPLS LDP MIB March 2000
mplsLdpConfFrRowStatus RowStatus
}
mplsLdpConfFrMinimumDlci OBJECT-TYPE
SYNTAX Integer32(0..4194303)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The lower bound which is supported. This value should
be the same as that in the Frame Relay Label Range
Component's Minimum DLCI field."
::= { mplsLdpEntityConfFrLabelRangeEntry 1 }
mplsLdpConfFrMaximumDlci OBJECT-TYPE
SYNTAX Integer32 (0..4194303)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The upper bound which is supported. This value should
be the same as that in the Frame Relay Label Range
Component's Maximum DLCI field."
::= { mplsLdpEntityConfFrLabelRangeEntry 2 }
mplsLdpConfFrStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The storage type for this entry."
::= { mplsLdpEntityConfFrLabelRangeEntry 3 }
mplsLdpConfFrRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An object that allows entries in this table to
be created and deleted using the
RowStatus convention.
If the value of the object
'mplsLdpEntityOptionalParameters' contains the
value of 'frameRelaySessionParameters(3)' then
there must be at least one corresponding entry
in this table.
NOTE: This RowStatus object should
have the same value of the 'mplsLdpEntityRowStatus'
Expires September 2000 [Page 35]
INTERNET-DRAFT MPLS LDP MIB March 2000
related to this entry."
::= { mplsLdpEntityConfFrLabelRangeEntry 4 }
--
-- The MPLS LDP Entity Statistics Table
--
mplsLdpEntityStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsLdpEntityStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table is a read-only table which augments
the mplsLdpEntityTable. The purpose of this
table is to keep statistical information about
the LDP Entities on the LSR."
::= { mplsLdpEntityObjects 6 }
mplsLdpEntityStatsEntry OBJECT-TYPE
SYNTAX MplsLdpEntityStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A row in this table contains statistical information
about an LDP Entity. Some counters contained in a
row are for fatal errors received during a former
LDP Session associated with this entry. For example,
an Ldp Pdu received on a TCP connection for an
LDP Session which contains a fatal error is counted
here, because the session is terminated.
If the error is NOT fatal (i.e. and the Session
remains), then the error is counted in the
mplsLdpSessionStatsEntry."
AUGMENTS { mplsLdpEntityEntry }
::= { mplsLdpEntityStatsTable 1 }
MplsLdpEntityStatsEntry ::= SEQUENCE {
mplsLdpAttemptedSessions Counter32,
mplsLdpSessionRejectedNoHelloErrors Counter32,
mplsLdpSessionRejectedAdvertisementErrors Counter32,
mplsLdpSessionRejectedMaxPduErrors Counter32,
mplsLdpSessionRejectedLabelRangeErrors Counter32,
mplsLdpBadLdpIdentifierErrors Counter32,
mplsLdpBadPduLengthErrors Counter32,
mplsLdpBadMessageLengthErrors Counter32,
mplsLdpBadTlvLengthErrors Counter32,
mplsLdpMalformedTlvValueErrors Counter32,
mplsLdpKeepAliveTimerExpiredErrors Counter32,
mplsLdpShutdownNotifReceived Counter32,
mplsLdpShutdownNotifSent Counter32
Expires September 2000 [Page 36]
INTERNET-DRAFT MPLS LDP MIB March 2000
}
mplsLdpAttemptedSessions OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A count of the total attempted sessions for
this LDP Entity."
::= { mplsLdpEntityStatsEntry 1 }
mplsLdpSessionRejectedNoHelloErrors OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A count of the Session Rejected/No Hello Error
Notification Messages sent or received by
this LDP Entity."
::= { mplsLdpEntityStatsEntry 2 }
mplsLdpSessionRejectedAdvertisementErrors OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A count of the Session Rejected/Parameters
Advertisement Mode Error Notification Messages sent
or received by this LDP Entity."
::= { mplsLdpEntityStatsEntry 3 }
mplsLdpSessionRejectedMaxPduErrors OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A count of the Session Rejected/Parameters
Max Pdu Length Error Notification Messages sent
or received by this LDP Entity."
::= { mplsLdpEntityStatsEntry 4 }
mplsLdpSessionRejectedLabelRangeErrors OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A count of the Session Rejected/Parameters
Label Range Notification Notification Messages sent
Expires September 2000 [Page 37]
INTERNET-DRAFT MPLS LDP MIB March 2000
or received by this LDP Entity."
::= { mplsLdpEntityStatsEntry 5 }
mplsLdpBadLdpIdentifierErrors OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of Bad LDP Identifier
Fatal Errors detected by the session(s)
(past and present) associated with this LDP Entity."
REFERENCE
"LDP Specification, Section 3.5.1.2."
::= { mplsLdpEntityStatsEntry 6 }
mplsLdpBadPduLengthErrors OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of Bad Pdu Length
Fatal Errors detected by the session(s)
(past and present) associated with this LDP Entity."
REFERENCE
"LDP Specification, Section 3.5.1.2."
::= { mplsLdpEntityStatsEntry 7 }
mplsLdpBadMessageLengthErrors OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of Bad Message
Length Fatal Errors detected by the session(s)
(past and present) associated with this LDP Entity."
REFERENCE
"LDP Specification, Section 3.5.1.2."
::= { mplsLdpEntityStatsEntry 8 }
mplsLdpBadTlvLengthErrors OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of Bad TLV
Length Fatal Errors detected by the session(s)
(past and present) associated with this LDP Entity."
REFERENCE
"LDP Specification, Section 3.5.1.2."
Expires September 2000 [Page 38]
INTERNET-DRAFT MPLS LDP MIB March 2000
::= { mplsLdpEntityStatsEntry 9 }
mplsLdpMalformedTlvValueErrors OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of Malformed TLV
Value Fatal Errors detected by the session(s)
(past and present) associated with this
LDP Entity."
REFERENCE
"LDP Specification, Section 3.5.1.2."
::= { mplsLdpEntityStatsEntry 10 }
mplsLdpKeepAliveTimerExpiredErrors OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of Session Keep Alive
Timer Expired Errors detected by the session(s)
(past and present) associated with this LDP Entity."
REFERENCE
"LDP Specification, Section 3.5.1.2."
::= { mplsLdpEntityStatsEntry 11 }
mplsLdpShutdownNotifReceived OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of Shutdown Notfications
received related to session(s) (past and present)
associated with this LDP Entity."
::= { mplsLdpEntityStatsEntry 12 }
mplsLdpShutdownNotifSent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of Shutdown Notfications
sent related to session(s) (past and present) associated
with this LDP Entity."
::= { mplsLdpEntityStatsEntry 13 }
--
-- The MPLS LDP Entity Peer Table
Expires September 2000 [Page 39]
INTERNET-DRAFT MPLS LDP MIB March 2000
--
mplsLdpEntityPeerObjects OBJECT IDENTIFIER ::=
{ mplsLdpObjects 3 }
mplsLdpEntityPeerTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsLdpEntityPeerEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information about LDP peers known by Entities in
the mplsLdpEntityTable. The information in this table
is based on information from the Entity-Peer interaction
but is not appropriate for the mplsLdpSessionTable."
::= { mplsLdpEntityPeerObjects 1 }
mplsLdpEntityPeerEntry OBJECT-TYPE
SYNTAX MplsLdpEntityPeerEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information about a single Peer which is related
to an entity."
INDEX { mplsLdpEntityLdpId,
mplsLdpEntityIndex,
mplsLdpPeerLdpId }
::= { mplsLdpEntityPeerTable 1 }
MplsLdpEntityPeerEntry ::= SEQUENCE {
mplsLdpPeerLdpId MplsLdpIdentifier,
mplsLdpPeerLabelDistributionMethod INTEGER,
mplsLdpPeerLoopDetectionForPV INTEGER,
mplsLdpPeerPathVectorLimit Integer32
}
mplsLdpPeerLdpId OBJECT-TYPE
SYNTAX MplsLdpIdentifier
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The LDP identifier of this LDP Peer."
::= { mplsLdpEntityPeerEntry 1 }
mplsLdpPeerLabelDistributionMethod OBJECT-TYPE
SYNTAX INTEGER {
downstreamOnDemand(1),
downstreamUnsolicited(2)
}
MAX-ACCESS read-only
STATUS current
Expires September 2000 [Page 40]
INTERNET-DRAFT MPLS LDP MIB March 2000
DESCRIPTION
"For any given LDP session, the method of
label distribution must be specified."
REFERENCE
"draft-ietf-mpls-arch-06.txt [20]."
::= { mplsLdpEntityPeerEntry 2 }
mplsLdpPeerLoopDetectionForPV OBJECT-TYPE
SYNTAX INTEGER {
disabled(0),
enabled(1)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An indication of whether loop detection based
on path vectors is disabled or enabled for this Peer.
If this object has a value of disabled(0),
then loop detection is disabled. Otherwise, if this
object has a value of enabled(1), then loop detection
based on path vectors is enabled."
::= { mplsLdpEntityPeerEntry 3 }
mplsLdpPeerPathVectorLimit OBJECT-TYPE
SYNTAX Integer32 (0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If the value of 'mplsLdpPeerLoopDetectionForPV' for
this entry is 'enabled(1)', the this object represents
that Path Vector Limit for this peer.
If the value of 'mplsLdpPeerLoopDetectionForPV' for
this entry is 'disabled(0)', then this value should
be 0 (zero)."
::= { mplsLdpEntityPeerEntry 4 }
--
-- The MPLS LDP Hello Adjacency Table
--
mplsLdpHelloAdjacencyObjects OBJECT IDENTIFIER ::=
{ mplsLdpEntityPeerObjects 2 }
mplsLdpHelloAdjacencyTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsLdpHelloAdjacencyEntry
Expires September 2000 [Page 41]
INTERNET-DRAFT MPLS LDP MIB March 2000
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of Hello Adjacencies for Sessions."
::= { mplsLdpHelloAdjacencyObjects 1 }
mplsLdpHelloAdjacencyEntry OBJECT-TYPE
SYNTAX MplsLdpHelloAdjacencyEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each row represents a single LDP Hello Adjacency.
An LDP Session can have one or more Hello adjacencies."
INDEX { mplsLdpEntityLdpId,
mplsLdpEntityIndex,
mplsLdpPeerLdpId,
mplsLdpHelloAdjacencyIndex }
::= { mplsLdpHelloAdjacencyTable 1 }
MplsLdpHelloAdjacencyEntry ::= SEQUENCE {
mplsLdpHelloAdjacencyIndex Unsigned32,
mplsLdpHelloAdjacencyHoldTimeRemaining TimeInterval,
mplsLdpHelloAdjacencyType INTEGER
}
mplsLdpHelloAdjacencyIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An identifier for this specific adjacency."
::= { mplsLdpHelloAdjacencyEntry 1 }
mplsLdpHelloAdjacencyHoldTimeRemaining OBJECT-TYPE
SYNTAX TimeInterval
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time remaining for this Hello Adjacency.
This interval will change when the 'next'
Hello message which corresponds to this
Hello Adjacency is received."
::= { mplsLdpHelloAdjacencyEntry 2 }
mplsLdpHelloAdjacencyType OBJECT-TYPE
SYNTAX INTEGER {
link(1),
targeted(2)
}
MAX-ACCESS read-only
Expires September 2000 [Page 42]
INTERNET-DRAFT MPLS LDP MIB March 2000
STATUS current
DESCRIPTION
"This adjacency is the result of a 'link'
hello if the value of this object is link(1).
Otherwise, it is a result of a 'targeted'
hello, targeted(2)."
::= { mplsLdpHelloAdjacencyEntry 3 }
--
-- The MPLS LDP Sessions Table
--
mplsLdpSessionObjects OBJECT IDENTIFIER ::=
{ mplsLdpEntityPeerObjects 3 }
mplsLdpSessionUpDownTrapEnable OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Indicates whether the traps, 'mplsLdpSessionUp' and
'mplsLdpSessionDown' will be generated or not.
If the value of this object is 'enabled(1)'
then the traps will generated. If the value
of this object is 'disabled(2)' then the
traps will not be generated. The DEFVAL
is set to 'disabled(1)'."
DEFVAL { disabled }
::= { mplsLdpSessionObjects 1 }
mplsLdpSessionTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsLdpSessionEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of Sessions between the LDP Entities and
LDP Peers. Each row represents a single session."
::= { mplsLdpSessionObjects 2 }
mplsLdpSessionEntry OBJECT-TYPE
SYNTAX MplsLdpSessionEntry
MAX-ACCESS not-accessible
Expires September 2000 [Page 43]
INTERNET-DRAFT MPLS LDP MIB March 2000
STATUS current
DESCRIPTION
"An entry in this table represents information on a
single session between an LDP Entity and LDP Peer.
The information contained in a row is read-only."
INDEX { mplsLdpEntityLdpId,
mplsLdpEntityIndex,
mplsLdpPeerLdpId
}
::= { mplsLdpSessionTable 1 }
MplsLdpSessionEntry ::= SEQUENCE {
mplsLdpSessionState INTEGER,
mplsLdpSessionProtocolVersion Integer32,
mplsLdpSessionKeepAliveHoldTimeRemaining TimeInterval,
mplsLdpSessionMaxPduLength Unsigned32,
mplsLdpSessionDiscontinuityTime TimeStamp
}
mplsLdpSessionState OBJECT-TYPE
SYNTAX INTEGER {
nonexistent(1),
initialized(2),
openrec(3),
opensent(4),
operational(5)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current state of the session, all of the
states 1 - 5 are based on the state machine for
session negotiation behavior."
::= { mplsLdpSessionEntry 1 }
mplsLdpSessionProtocolVersion OBJECT-TYPE
SYNTAX Integer32(1..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The version of the LDP Protocol which
this session is using."
::= { mplsLdpSessionEntry 2 }
mplsLdpSessionKeepAliveHoldTimeRemaining OBJECT-TYPE
SYNTAX TimeInterval
MAX-ACCESS read-only
STATUS current
DESCRIPTION
Expires September 2000 [Page 44]
INTERNET-DRAFT MPLS LDP MIB March 2000
"The keep alive hold time remaining for this session."
::= { mplsLdpSessionEntry 3 }
mplsLdpSessionMaxPduLength OBJECT-TYPE
SYNTAX Unsigned32 (1..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of maximum allowable length for LDP PDUs for
this session. This value may have been negotiated during
the Session Initialization."
::= { mplsLdpSessionEntry 4 }
mplsLdpSessionDiscontinuityTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime on the most recent occasion at
which any one or more of this session's counters
suffered a discontinuity. The relevant counters are
the specific instances associated with this session
of any Counter32 or Counter64 object contained in the
mplsLdpSessionStatsTable. If no such discontinuities have
occurred since the last re-initialization of the local
management subsystem, then this object contains a zero
value.
Also, an NMS can distinguish when a session
between a given Entity and Peer goes away and then is
're-established'. This value would change and
thus indicate to the NMS that this is a
different session."
::= { mplsLdpSessionEntry 5 }
--
-- MPLS LDP ATM Session Information
--
mplsLdpAtmSessionTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsLdpAtmSessionEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table which relates Sessions in the
'mplsLdpSessionTable' and their label
range intersections. There could be one
or more label range intersections between an
LDP Entity and LDP Peer using ATM as the underlying
Expires September 2000 [Page 45]
INTERNET-DRAFT MPLS LDP MIB March 2000
media. Each row represents a single label range
intersection.
NOTE: this table cannot use the 'AUGMENTS'
clause because there is not necessarily a one-to-one
mapping between this table and the mplsLdpSessionTable."
::= { mplsLdpSessionObjects 4 }
mplsLdpAtmSessionEntry OBJECT-TYPE
SYNTAX MplsLdpAtmSessionEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table represents information on a
single label range intersection between an LDP Entity
and LDP Peer.
The information contained in a row is read-only."
INDEX { mplsLdpEntityLdpId,
mplsLdpEntityIndex,
mplsLdpPeerLdpId,
mplsLdpSessionAtmLabelRangeLowerBoundVpi,
mplsLdpSessionAtmLabelRangeLowerBoundVci
}
::= { mplsLdpAtmSessionTable 1 }
MplsLdpAtmSessionEntry ::= SEQUENCE {
mplsLdpSessionAtmLabelRangeLowerBoundVpi AtmVpIdentifier,
mplsLdpSessionAtmLabelRangeLowerBoundVci AtmVcIdentifier,
mplsLdpSessionAtmLabelRangeUpperBoundVpi AtmVpIdentifier,
mplsLdpSessionAtmLabelRangeUpperBoundVci AtmVcIdentifier
}
mplsLdpSessionAtmLabelRangeLowerBoundVpi OBJECT-TYPE
SYNTAX AtmVpIdentifier
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The minimum VPI number for this range."
::= { mplsLdpAtmSessionEntry 1 }
mplsLdpSessionAtmLabelRangeLowerBoundVci OBJECT-TYPE
SYNTAX AtmVcIdentifier
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The minimum VCI number for this range."
::= { mplsLdpAtmSessionEntry 2 }
Expires September 2000 [Page 46]
INTERNET-DRAFT MPLS LDP MIB March 2000
mplsLdpSessionAtmLabelRangeUpperBoundVpi OBJECT-TYPE
SYNTAX AtmVpIdentifier
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum VPI number for this range."
::= { mplsLdpAtmSessionEntry 3 }
mplsLdpSessionAtmLabelRangeUpperBoundVci OBJECT-TYPE
SYNTAX AtmVcIdentifier
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum VCI number for this range."
::= { mplsLdpAtmSessionEntry 4 }
--
-- MPLS LDP Frame Relay Session Information
--
mplsLdpFrameRelaySessionTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsLdpFrameRelaySessionEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of Frame Relay label range intersections
between the LDP Entities and LDP Peers.
Each row represents a single label range intersection.
NOTE: this table cannot use the 'AUGMENTS'
clause because there is not necessarily a one-to-one
mapping between this table and the mplsLdpSessionTable."
::= { mplsLdpSessionObjects 5 }
mplsLdpFrameRelaySessionEntry OBJECT-TYPE
SYNTAX MplsLdpFrameRelaySessionEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table represents information on a
single label range intersection between an
LDP Entity and LDP Peer.
The information contained in a row is read-only."
INDEX { mplsLdpEntityLdpId,
mplsLdpEntityIndex,
mplsLdpPeerLdpId,
mplsLdpFrSessionMinDlci
}
Expires September 2000 [Page 47]
INTERNET-DRAFT MPLS LDP MIB March 2000
::= { mplsLdpFrameRelaySessionTable 1 }
MplsLdpFrameRelaySessionEntry ::= SEQUENCE {
mplsLdpFrSessionMinDlci Integer32,
mplsLdpFrSessionMaxDlci Integer32,
mplsLdpFrSessionLen INTEGER
}
mplsLdpFrSessionMinDlci OBJECT-TYPE
SYNTAX Integer32(0..4194303)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The lower bound of DLCIs which are supported."
::= { mplsLdpFrameRelaySessionEntry 1 }
mplsLdpFrSessionMaxDlci OBJECT-TYPE
SYNTAX Integer32 (0..4194303)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The upper bound of DLCIs which are supported."
::= { mplsLdpFrameRelaySessionEntry 2 }
mplsLdpFrSessionLen OBJECT-TYPE
SYNTAX INTEGER {
tenDlciBits(0),
twentyThreeDlciBits(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the DLCI bits."
::= { mplsLdpFrameRelaySessionEntry 3 }
--
-- The MPLS LDP Session Statistics Table
--
mplsLdpSessionStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsLdpSessionStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of statistics for Sessions between
LDP Entities and LDP Peers."
::= { mplsLdpSessionObjects 6 }
Expires September 2000 [Page 48]
INTERNET-DRAFT MPLS LDP MIB March 2000
mplsLdpSessionStatsEntry OBJECT-TYPE
SYNTAX MplsLdpSessionStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table represents statistical
information on a single session between an LDP
Entity and LDP Peer."
AUGMENTS { mplsLdpSessionEntry }
::= { mplsLdpSessionStatsTable 1 }
MplsLdpSessionStatsEntry ::= SEQUENCE {
mplsLdpSessionStatsUnknownMessageTypeErrors Counter32,
mplsLdpSessionStatsUnknownTlvErrors Counter32
}
mplsLdpSessionStatsUnknownMessageTypeErrors OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of Unknown Message Type
Errors detected during this session.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of
mplsLdpSeeionDiscontinuityTime."
::= { mplsLdpSessionStatsEntry 1 }
mplsLdpSessionStatsUnknownTlvErrors OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of Unknown TLV Errors
detected during this session.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of
mplsLdpSeeionDiscontinuityTime."
::= { mplsLdpSessionStatsEntry 2 }
--
-- Address Message/Address Withdraw Message Information
--
-- This information is associated with a specific Session
-- because Label Address Messages are sent after session
Expires September 2000 [Page 49]
INTERNET-DRAFT MPLS LDP MIB March 2000
-- initialization has taken place.
--
mplsLdpSessionPeerAddressTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsLdpSessionPeerAddressEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table 'extends' the mplsLdpSessionTable.
This table is used to store Label Address Information
from Label Address Messages received by this LSR from
Peers. This table is read-only and should be updated
when Label Withdraw Address Messages are received, i.e.
Rows should be deleted as apropriate.
NOTE: since more than one address may be contained
in a Label Address Message, this table 'extends',
rather than 'AUGMENTS' the mplsLdpSessionTable's
information."
::= { mplsLdpSessionObjects 7 }
mplsLdpSessionPeerAddressEntry OBJECT-TYPE
SYNTAX MplsLdpSessionPeerAddressEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table represents information on
session's for a single next hop address which was
advertised in an Address Message from the LDP peer.
The information contained in a row is read-only."
INDEX { mplsLdpEntityLdpId,
mplsLdpEntityIndex,
mplsLdpPeerLdpId,
mplsLdpSessionPeerAddressIndex
}
::= { mplsLdpSessionPeerAddressTable 1 }
MplsLdpSessionPeerAddressEntry ::= SEQUENCE {
mplsLdpSessionPeerAddressIndex Unsigned32,
mplsLdpSessionPeerNextHopAddressType AddressFamilyNumbers,
mplsLdpSessionPeerNextHopAddress MplsLdpGenAddr
}
mplsLdpSessionPeerAddressIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An index which uniquely identifies this entry within
a given session."
Expires September 2000 [Page 50]
INTERNET-DRAFT MPLS LDP MIB March 2000
::= { mplsLdpSessionPeerAddressEntry 1 }
mplsLdpSessionPeerNextHopAddressType OBJECT-TYPE
SYNTAX AddressFamilyNumbers
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The internetwork layer address type of this Next Hop
Address as specified in the Label Address Message
associated with this Session. The value of this
object indicates how to interpret the value of
mplsLdpSessionPeerNextHopAddress."
::= { mplsLdpSessionPeerAddressEntry 2 }
mplsLdpSessionPeerNextHopAddress OBJECT-TYPE
SYNTAX MplsLdpGenAddr
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of the next hop address."
REFERENCE
"LDP Specification [18] defines only IPv4 for LDP Protocol
Version 1, see section 3.4.3."
::= { mplsLdpSessionPeerAddressEntry 3 }
--
-- MPLS LDP LIB Table
--
mplsLdpLibObjects OBJECT IDENTIFIER ::= { mplsLdpObjects 6 }
mplsLdpLibLspUpDownTrapEnable OBJECT-TYPE
SYNTAX INTEGER { enabled(1), disabled(2) }
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Indicates whether traps related to
an LSP's operation status should be sent.
If the value of this object is 'enabled(1)'
then the 'mplsLdpLibLspUp' and the
'mplsLdpLibLspDown' traps will be sent.
If the value of this object is 'disabled(2)'
then those traps will not be sent."
DEFVAL { disabled }
::= { mplsLdpLibObjects 1 }
mplsLdpLibTable OBJECT-TYPE
Expires September 2000 [Page 51]
INTERNET-DRAFT MPLS LDP MIB March 2000
SYNTAX SEQUENCE OF MplsLdpLibEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table represents LIB (Label Information Base)
Information. The table is read-only."
::= { mplsLdpLibObjects 2 }
mplsLdpLibEntry OBJECT-TYPE
SYNTAX MplsLdpLibEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each row represents a single LDP LIB entry."
INDEX { mplsLdpLibLspId }
::= { mplsLdpLibTable 1 }
MplsLdpLibEntry ::= SEQUENCE {
mplsLdpLibLspId Unsigned32,
mplsLdpLibLabelInIfIndex InterfaceIndex,
mplsLdpLibLabelOutIfIndex InterfaceIndex,
mplsLdpLibInLabelType MplsLdpLabelTypes,
mplsLdpLibInLabel MplsLabel,
mplsLdpLibOutLabelType MplsLdpLabelTypes,
mplsLdpLibOutLabel MplsLabel,
mplsLdpLibOperationStatus INTEGER,
mplsLdpLibLspLastChange TimeStamp
}
mplsLdpLibLspId OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This number is used to uniquely identify this row,
since this row is associated with a specific LSP,
it may also be used to describe a unique number
for an LSP. This number is used in the
mplsLdpFecTable to identify which FECs or FEC is
associated with this LIB entry."
::= { mplsLdpLibEntry 1 }
mplsLdpLibLabelInIfIndex OBJECT-TYPE
SYNTAX InterfaceIndex
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ifIndex of the 'mplsLdpInLabel'."
::= { mplsLdpLibEntry 2 }
Expires September 2000 [Page 52]
INTERNET-DRAFT MPLS LDP MIB March 2000
mplsLdpLibLabelOutIfIndex OBJECT-TYPE
SYNTAX InterfaceIndex
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ifIndex of the 'mplsLdpOutLabel'."
::= { mplsLdpLibEntry 3 }
mplsLdpLibInLabelType OBJECT-TYPE
SYNTAX MplsLdpLabelTypes
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Layer 2 Label Type for 'mplsLdpInLabel'."
::= { mplsLdpLibEntry 4 }
mplsLdpLibInLabel OBJECT-TYPE
SYNTAX MplsLabel
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The incoming label of this LSP."
::= { mplsLdpLibEntry 5 }
mplsLdpLibOutLabelType OBJECT-TYPE
SYNTAX MplsLdpLabelTypes
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Layer 2 Label Type for 'mplsLdpOutLabel'."
::= { mplsLdpLibEntry 6 }
mplsLdpLibOutLabel OBJECT-TYPE
SYNTAX MplsLabel
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The outgoing label of this LSP."
::= { mplsLdpLibEntry 7 }
mplsLdpLibOperationStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(1), -- cannot be determined
up(2), -- LSP is up
down(3) -- LSP is down
}
MAX-ACCESS read-only
STATUS current
Expires September 2000 [Page 53]
INTERNET-DRAFT MPLS LDP MIB March 2000
DESCRIPTION
"The operation status of this LSP.
unknown(1), -- cannot be determined
up(2), -- LSP is up
down(3) -- LSP is down."
::= { mplsLdpLibEntry 8 }
mplsLdpLibLspLastChange OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime on the most recent occasion
that the 'mplsLdpLibOperationStatus' changed. If the
status has not changed since the last re-initialization
of the network management entity (i.e. SNMP agent), then
this object should have the value of 0 (zero)."
::= { mplsLdpLibEntry 9 }
--
-- Mpls Ldp FEC Table
--
mplsLdpFecTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsLdpFecEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table represents the FEC
(Forwarding Equivalence Class)
Information associated with an LSP.
The table is read-only."
::= { mplsLdpLibObjects 3 }
mplsLdpFecEntry OBJECT-TYPE
SYNTAX MplsLdpFecEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each row represents a single FEC Element."
INDEX { mplsLdpFecType,
mplsLdpFecAddressFamily,
mplsLdpFecAddressLength,
mplsLdpFecAddress,
mplsLdpFecLspId
}
::= { mplsLdpFecTable 1 }
MplsLdpFecEntry ::= SEQUENCE {
Expires September 2000 [Page 54]
INTERNET-DRAFT MPLS LDP MIB March 2000
mplsLdpFecType INTEGER,
mplsLdpFecAddressFamily AddressFamilyNumbers,
mplsLdpFecAddressLength Integer32,
mplsLdpFecAddress MplsLdpGenAddr,
mplsLdpFecLspId Unsigned32,
mplsLdpFecSessionRowPointer RowPointer
}
mplsLdpFecType OBJECT-TYPE
SYNTAX INTEGER {
prefix(1),
hostAddress(2)
}
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The type of the FEC. If the value of this object
is 'prefix(1)' then the FEC type described by this
row is for address prefixes.
If the value of this object is 'hostAddress(2)' then
the FEC type described by this row is a host address."
::= { mplsLdpFecEntry 1 }
mplsLdpFecAddressFamily OBJECT-TYPE
SYNTAX AddressFamilyNumbers
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The value of this object is from the Address Family
Numbers."
::= { mplsLdpFecEntry 2 }
mplsLdpFecAddressLength OBJECT-TYPE
SYNTAX Integer32(0..255)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"If the value of 'mplsLdpFecType' is 'prefix(1)'
then the value of this object is the length in
bits of the address prefix represented by
'mplsLdpFecAddress', or if the length is zero then
this is a special value which indicates that the
prefix matches all addresses. In this case the
prefix is also zero (i.e. 'mplsLdpFecAddress' will
have the value of zero.)"
::= { mplsLdpFecEntry 3 }
Expires September 2000 [Page 55]
INTERNET-DRAFT MPLS LDP MIB March 2000
mplsLdpFecAddress OBJECT-TYPE
SYNTAX MplsLdpGenAddr
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"If the value of 'mplsLdpFecType' is 'prefix(1)'
then the value of this object is the address prefix.
If the value of the 'mplsLdpFecAddressLength'
is object is zero, then this object should also be
zero."
::= { mplsLdpFecEntry 4 }
mplsLdpFecLspId OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This number represents the LSP which is related to
this FEC. The value of this index should correspond
to the 'mplsLdpLibLspId' in the LIB table."
::= { mplsLdpFecEntry 5 }
mplsLdpFecSessionRowPointer OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A pointer to a row in the 'mplsLdpSessionTable' which
is related to this FEC entry.
The NULL OID zeroDotzero is interpreted to mean
there is no known Session related to this FEC."
::= { mplsLdpFecEntry 6 }
---
--- Notifications
---
mplsLdpNotificationPrefix OBJECT IDENTIFIER ::=
{ mplsLdpNotifications 0 }
mplsLdpFailedInitSessionThresholdExceeded NOTIFICATION-TYPE
OBJECTS {
mplsLdpEntityFailedInitSessionThreshold
}
STATUS current
DESCRIPTION
"This notification is generated when the value of
the 'mplsLdpEntityPVLimitMismatchTrapEnable' object
Expires September 2000 [Page 56]
INTERNET-DRAFT MPLS LDP MIB March 2000
is 'enabled(1)' and the value of the object,
'mplsLdpEntityFailedInitSessionThreshold' has
been exceeded."
::= { mplsLdpNotificationPrefix 1 }
mplsLdpPathVectorLimitMismatch NOTIFICATION-TYPE
OBJECTS {
mplsLdpEntityPathVectorLimit,
mplsLdpPeerPathVectorLimit
}
STATUS current
DESCRIPTION
"This notification is generated when the value
of the value of the object,
'mplsLdpEntityFailedInitSessionTrapEnable' is
'enabled(1)' and the
'mplsLdpEntityPathVectorLimit' does NOT match
the value of the 'mplsLdpPeerPathVectorLimit' for
a specific Entity."
REFERENCE
"LDP Specification, Section 3.5.3."
::= { mplsLdpNotificationPrefix 2 }
mplsLdpSessionUp NOTIFICATION-TYPE
OBJECTS {
mplsLdpSessionState
}
STATUS current
DESCRIPTION
"Generation of this trap occurs when the
'mplsLdpSessionUpDownTrapEnable' object is 'enabled(1)'
and the value of mplsLdpSessionState changes from
any state accept 'nonexistent(1)' to 'operational(5)'."
::= { mplsLdpNotificationPrefix 3 }
mplsLdpSessionDown NOTIFICATION-TYPE
OBJECTS {
mplsLdpSessionState
}
STATUS current
DESCRIPTION
"Generation of this trap occurs when the
'mplsLdpSessionUpDownTrapEnable' object is 'enabled(1)'
and the value of mplsLdpSessionState changes from
'operational(5)' to any other state."
::= { mplsLdpNotificationPrefix 4 }
mplsLdpLibLspUp NOTIFICATION-TYPE
OBJECTS {
Expires September 2000 [Page 57]
INTERNET-DRAFT MPLS LDP MIB March 2000
mplsLdpLibOperationStatus
}
STATUS current
DESCRIPTION
"Generation of this trap occurs when the
'mplsLdpLibLspUpDownTrapEnable' object is 'enabled(1)'
and the LSP operation status changes from any state
to 'up'."
::= { mplsLdpNotificationPrefix 5 }
mplsLdpLibLspDown NOTIFICATION-TYPE
OBJECTS {
mplsLdpLibOperationStatus
}
STATUS current
DESCRIPTION
"Generation of this trap occurs when the
'mplsLdpLibLspUpDownTrapEnable' object is 'enabled(1)'
and the LSP operation status changes from any state
to 'down'."
::= { mplsLdpNotificationPrefix 6 }
--****************************************************************
-- Module Conformance Statement
--****************************************************************
mplsLdpGroups
OBJECT IDENTIFIER ::= { mplsLdpConformance 1 }
mplsLdpCompliances
OBJECT IDENTIFIER ::= { mplsLdpConformance 2 }
--
-- Compliance Statements
--
mplsLdpModuleCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The basic implentation requirements for agents that
support the MPLS LDP MIB."
MODULE -- this module
MANDATORY-GROUPS { mplsLdpGeneralGroup,
mplsLdpNotificationsGroup
}
GROUP mplsLdpAtmGroup
DESCRIPTION
"This group must be supported if ATM is used in the
Expires September 2000 [Page 58]
INTERNET-DRAFT MPLS LDP MIB March 2000
MPLS LDP implementation."
GROUP mplsLdpFrameRelayGroup
DESCRIPTION
"This group must be supported if Frame Relay is used
in the MPLS LDP implementation."
::= { mplsLdpCompliances 1 }
-- units of conformance
mplsLdpGeneralGroup OBJECT-GROUP
OBJECTS {
mplsLdpLsrId,
mplsLdpLsrLabelRetentionMode,
mplsLdpLsrLoopDetectionCapable,
mplsLdpEntityIndexNext,
mplsLdpEntityProtocolVersion,
mplsLdpEntityAdminStatus,
mplsLdpEntityOperStatus,
mplsLdpEntityWellKnownDiscoveryPort,
mplsLdpEntityMaxPduLength,
mplsLdpEntityKeepAliveHoldTimer,
mplsLdpEntityHelloHoldTimer,
mplsLdpEntityFailedInitSessionTrapEnable,
mplsLdpEntityFailedInitSessionThreshold,
mplsLdpEntityLabelDistributionMethod,
mplsLdpEntityPVLimitMismatchTrapEnable,
mplsLdpEntityPathVectorLimit,
mplsLdpEntityHopCountLoopDetection,
mplsLdpEntityHopCount,
mplsLdpEntityTargetedPeer,
mplsLdpEntityTargetedPeerAddrType,
mplsLdpEntityTargetedPeerAddr,
mplsLdpEntityOptionalParameters,
mplsLdpEntityDiscontinuityTime,
mplsLdpEntityStorageType,
mplsLdpEntityRowStatus,
mplsLdpAttemptedSessions,
mplsLdpSessionRejectedNoHelloErrors,
mplsLdpSessionRejectedAdvertisementErrors,
mplsLdpSessionRejectedMaxPduErrors,
mplsLdpSessionRejectedLabelRangeErrors,
mplsLdpBadLdpIdentifierErrors,
mplsLdpBadPduLengthErrors,
mplsLdpBadMessageLengthErrors,
mplsLdpBadTlvLengthErrors,
mplsLdpMalformedTlvValueErrors,
mplsLdpKeepAliveTimerExpiredErrors,
mplsLdpShutdownNotifReceived,
mplsLdpShutdownNotifSent,
Expires September 2000 [Page 59]
INTERNET-DRAFT MPLS LDP MIB March 2000
mplsLdpPeerLabelDistributionMethod,
mplsLdpPeerLoopDetectionForPV,
mplsLdpPeerPathVectorLimit,
mplsLdpHelloAdjacencyHoldTimeRemaining,
mplsLdpHelloAdjacencyType,
mplsLdpSessionUpDownTrapEnable,
mplsLdpSessionState,
mplsLdpSessionProtocolVersion,
mplsLdpSessionKeepAliveHoldTimeRemaining,
mplsLdpSessionMaxPduLength,
mplsLdpSessionDiscontinuityTime,
mplsLdpSessionStatsUnknownMessageTypeErrors,
mplsLdpSessionStatsUnknownTlvErrors,
mplsLdpSessionPeerNextHopAddressType,
mplsLdpSessionPeerNextHopAddress,
mplsLdpLibLspUpDownTrapEnable,
mplsLdpLibLabelInIfIndex,
mplsLdpLibLabelOutIfIndex,
mplsLdpLibInLabelType,
mplsLdpLibInLabel,
mplsLdpLibOutLabelType,
mplsLdpLibOutLabel,
mplsLdpLibOperationStatus,
mplsLdpLibLspLastChange,
mplsLdpFecSessionRowPointer
}
STATUS current
DESCRIPTION
"Objects that apply to all MPLS LDP implementations."
::= { mplsLdpGroups 1 }
mplsLdpGenericGroup OBJECT-GROUP
OBJECTS {
mplsLdpConfGenericIfIndexOrZero,
mplsLdpConfGenericLabel,
mplsLdpConfGenericStorageType,
mplsLdpConfGenericRowStatus
}
STATUS current
DESCRIPTION
"Objects that apply to all MPLS LDP implementations
using Generic Lables."
::= { mplsLdpGroups 2 }
mplsLdpAtmGroup OBJECT-GROUP
OBJECTS {
mplsLdpEntityAtmIfIndexOrZero,
mplsLdpEntityAtmMergeCap,
Expires September 2000 [Page 60]
INTERNET-DRAFT MPLS LDP MIB March 2000
mplsLdpEntityAtmLabelRangeComponents,
mplsLdpEntityAtmVcDirectionality,
mplsLdpEntityAtmLsrConnectivity,
mplsLdpEntityDefaultControlVpi,
mplsLdpEntityDefaultControlVci,
mplsLdpEntityUnlabTrafVpi,
mplsLdpEntityUnlabTrafVci,
mplsLdpEntityAtmStorageType,
mplsLdpEntityAtmRowStatus,
mplsLdpEntityConfAtmLabelRangeMaximumVpi,
mplsLdpEntityConfAtmLabelRangeMaximumVci,
mplsLdpEntityConfAtmLabelRangeStorageType,
mplsLdpEntityConfAtmLabelRangeRowStatus,
mplsLdpSessionAtmLabelRangeUpperBoundVpi,
mplsLdpSessionAtmLabelRangeUpperBoundVci
}
STATUS current
DESCRIPTION
"Objects that apply to all MPLS LDP implementations
over ATM."
::= { mplsLdpGroups 3 }
mplsLdpFrameRelayGroup OBJECT-GROUP
OBJECTS {
mplsLdpEntityFrIfIndexOrZero,
mplsLdpEntityFrMergeCap,
mplsLdpEntityFrLabelRangeComponents,
mplsLdpEntityFrLen,
mplsLdpEntityFrVcDirectionality,
mplsLdpEntityFrParmsStorageType,
mplsLdpEntityFrParmsRowStatus,
mplsLdpConfFrMaximumDlci,
mplsLdpConfFrStorageType,
mplsLdpConfFrRowStatus,
mplsLdpFrSessionMaxDlci,
mplsLdpFrSessionLen
}
STATUS current
DESCRIPTION
"Objects that apply to all MPLS LDP implementations over
Frame Relay."
::= { mplsLdpGroups 4 }
mplsLdpNotificationsGroup NOTIFICATION-GROUP
NOTIFICATIONS { mplsLdpFailedInitSessionThresholdExceeded,
mplsLdpPathVectorLimitMismatch,
mplsLdpSessionUp,
mplsLdpSessionDown,
Expires September 2000 [Page 61]
INTERNET-DRAFT MPLS LDP MIB March 2000
mplsLdpLibLspUp,
mplsLdpLibLspDown
}
STATUS current
DESCRIPTION
"The notification(s) which an MPLS LDP implemention
is required to implement."
::= { mplsLdpGroups 5 }
END
Expires September 2000 [Page 62]
INTERNET-DRAFT MPLS LDP MIB March 2000
5. Revision History
This section should be removed when this document is published as an
RFC.
5.1. Changes from <draft-ietf-mpls-ldp-mib-04.txt>
Editorial changes, fixing typo's, fixing wrapping lines, etc.
Updated references for latest drafts, and added [33] and [34] to
Reference Section.
Added to the Acknowledgements Section.
Changed the SYNTAX and DESCRIPTION of the
'mplsLdpLsrLoopDetectionCapable' object, so that it will also support
the loop detection by hop count.
Combined the 'mplsLdpEntityLoopDetectionForPV' and
'mplsLdpEntityPathVectorLimit' objects. The functionality of the
'mplsLdpEntityLoopDectionForPV' is now denoted by the value of 0
(zero) in the 'mplsLdpEntityPathVectorLimit' object. This results in
one less object 'mplsLdpEntityLoopDectionForPV' but does not
sacrifice functionality.
Changed 'mplsLdpLibLabelType' into two objects:
'mplsLdpLibInLabelType' and differ from the egress label type. The
MIB now reflects this.
The following items were changed as a result of the Frame Relay Forum
dropping support for 17-bit DLCIs: the MplsLabel TC description has
been modified, and other Frame Relay Object descriptions were also
modified (as specified in this section).
The MplsLabel TC was also modified and reference 3. was added to the
REFERENCE Clause.
MplsLdpLabelTypes TC was modified to use an enum.
InterfaceIndex support was added to the Entity information. This was
specifically requested by several members of the working group. An
additional table, mplsLdpEntityConfGenericTable as a way to configure
Generic Labels, and an object, 'mplsLdpConfGenericIfIndexOrZero was
added to map the InterfaceIndex used by Generic Labels. Objects were
also added to the 'mplsLdpEntityAtmParmsTable' and the and
'mplsLdpEntityFrIfIndex', respectively.
Changed the name of the 'mplsLdpEntityMtu' object to be
'mplsLdpEntityMaxPduLength' which is more consistent with the LDP
Expires September 2000 [Page 63]
INTERNET-DRAFT MPLS LDP MIB March 2000
Specification. Also, the description and SYNTAX were changed.
Changed the SYNTAX of the 'mplsLdpSessionMaxPduLength' to unsigned32
and changed the Range from (0..65535) to (1..65535).
Added and improved the front section discussion on SNMP
Notifications.
Also, modified the DESCRIPTION clause of the
Added objects to enable/disable the sending of traps:
Added an object to enable/disable sending traps for Sessions changing
from Up to Down, or Down to Up.
Added notifications to generate traps from session changing from Up
to Down, or Down to up.
Added a StorageType object to the Entity and associated tables which
are configurable.
Added a Discontinuity Time object to the Entity Table,
Added discussion on row creation in the Entity and other associated
Entity tables. This is a new Section in the Front part of the
document called:
Removed the 'mplsLdpEntityControlMethod'.
Made 'mplsLdpFecLspId' as part of the INDEX for the FEC table. This
is to allow FECs to map to multiple LSPs. Also add a RowPointer to a
row in the Session Table.
Added an operation status object, 'mplsLdpLspOperationStatus' and a
last Change object, 'mplsLdpLspLastChangeto the LIB Table. This will
be used to detect whether an LSP has changed its status.
Changed the name of the mplsLdpPeerTable to the
mplsLdpEntityPeerTable. This table contains information relevant to
Peers which are known to specific Entities. The indexing of this
table has also changed to include the Row in the Entity Table that
this Peer is known by. The mplsLdpHelloAdjacencyTable and the
mplsLdpSessionTable have been moved under this table. Since Hello
Adjacencies are related to Entity-Peer information and Sessions are
related to Entity-Peer information this was seen as a comprehensive
and coherent modelling. Associated descriptions in the front section
and in the tables have been changed to reflect this change.
Moved the 'mplsLdpConfFrLen' object from the
'mplsLdpEntityConfFrLabelRangeTable' to the
Expires September 2000 [Page 64]
INTERNET-DRAFT MPLS LDP MIB March 2000
'mplsLdpEntityFrameRelayParmsTable' since the Frame Relay
interface/port can only use one header length at a time, i.e. a
specific FR interface supports one address length for all VCs on that
interface. Also, changed the object so that it only supports 10 and
23 bit DLCI lengths. (The 17 bit length was dropped by the Frame
Relay Forum and thus, is no longer required.) The name of this
object was changed from 'mplsLdpConfFrLen' to 'mplsLdpEntityFrLen' to
fit in with the 'mplsLdpEntityFrameRelayParmsTable'.
Removed the seventeenDlciBits(1) value from the mplsLdpFrSessionLen
object. (The 17 bit length was dropped by the Frame Relay Forum and
thus, is no longer required.)
Corrected the range of the 'mplsLdpEntityIndexNext' object to include
0 (zero).
5.2. Changes from <draft-ietf-mpls-ldp-mib-03.txt>
Reworded the description of the mplsLdpAtmSessionTable to clarify
that one or MORE label range intersection(s) is/are represented in
this table.
Reworded the description of the mplsLdpFrameRelaySessionTable to
clarify that one or MORE label range intersection(s) is/are
represented in this table.
Added a new index, mplsLdpSessionPeerIndex, to the
mplsLdpSessionPeerAddressTable. This new index uniquely identifies
the entry within a given session. (Since adding
mplsLdpSessionPeerNextHopAddressType,
mplsLdpSessionPeerNextHopAddress to the INDEX clause of the
mplsLdpSessionPeerAddressTable leaves a table with only indices and
no objects, the work around was to add a new index which uniquely
differentiates an entry within a given session.)
Quite a few changes to the mplsLdpPeerTable. First, removed the
mplsLdpPeerIndex from the mplsLdpPeerTable and other tables. This
index served no purpose, so was removed. Second, removed the
objects: mplsLdpPeerInternetworkAddrType, and
mplsLdpPeerInternetworkAddr. Third, reworded the description of this
table to include information which is known during Session
Intialization attempts, the specific information has to do with Loop
Dection based on Path Vectors. Since Section 3.5.3 of the LDP Spec
when describing the PVLim says: "Although knowledge of a peer's path
vector limit will not change an LSR's behavior, it does enable the
LSR to alert an operator to a possible misconfiguration." and the
object mplsLdpPeerPathVectorLimit is sent as a varbind in the
mplsLdpPathVectorLimitMismatch notification.
Expires September 2000 [Page 65]
INTERNET-DRAFT MPLS LDP MIB March 2000
Removed the mplsLdpPeerIndex from the mplsLdpHelloAdjacencyTable.
Removed the "IANA Address Family Numbers MIB" section.
Updated the boiler.me from the ops web page dated Weds., Dec 22,
1999.
Updated the Security Section from the ops web page.
Added the following objects to the mplsLdpEntityTable:
mplsLdpEntityControlMethod, mplsLdpEntityLoopDectionForPV, and
mplsLdpEntityPathVectorLimit.
Removed mplsLdpSessionLabelAdvertisement,
mplsLdpSessionLoopDetectionForPV, and mplsLdpSessionPathVectorLimit
from the mplsLdpSessionTable.
Changed the mplsLdpPathVectorLimitMismatch Notification to send
mplsLdpEntityPathVectorLimit (instead of
mplsLdpSessionPathVectorLimit).
Copied the MplsLabel TC from draft-ietf-mpls-lsr-mib-00.txt and
replaced the MplsLdpGenAddr for mplsLdpLibInLabel and
mpslLdpLibOutLabel with MplsLabel.
The mplsLdpSessionIndex was removed throughout the MIB. This was
replaced by the object mplsLdpSessionDiscontinuityTime. The
motivation was to reduce the number of indices.
The descriptions for the objects in the mplsLdpSessionStatsTable,
mplsLdpSessionStatsUnknownMessageTypeErrors and
mplsLdpSessionStatsUnknownTlvErrors, have been updated to include a
reference to the mplsLdpSessionDiscontinuityTime object.
5.3. Changes from <draft-ietf-mpls-ldp-mib-02.txt>
Added Scalar Objects: mplsLdpLsrLoopDetectionPresent, and
mplsLdpEntityIndexNext.
Added the following objects to the mplsLdpEntityTable:
mplsLdpEntityProtocolVersion, mplsLdpEntityAdminStatus,
mplsLdpEntityOperStatus, mplsLdpEntityTargetedPeer,
mplsLdpEntityTargetedPeerAddrType, mplsLdpEntityTargetedPeerAddr, and
mplsLdpEntityHelloHoldTimer.
Changed the description of the mplsLdpEntityAtmParmsTable and added
the following objects to this table:
mplsLdpEntityAtmLsrConnectivity, mplsLdpEntityDefaultControlVpi,
mplsLdpEntityDefaultControlVci, mplsLdpEntityUnlabTrafVpi, and
Expires September 2000 [Page 66]
INTERNET-DRAFT MPLS LDP MIB March 2000
mplsLdpEntityUnlabTrafVci. NOTE: the last four objects were in
Version 01 of the MIB but were mistakenly omitted from Version 02.
Now, they are back.
Changed the indexing of the mplsLdpEntityConfAtmLabelRangeTable to
include the minimum VPI/VCI. This is to ensure that indices in this
table are unique.
Changed the indexing of the mplsLdpEntityConfFrLabelRangeTable, to
include the minimum DLCI value. This is to ensure that indices in
this table are unique.
Added [32] to Reference Section.
5.4. Changes from <draft-ietf-mpls-ldp-mib-01.txt>
The MIB was updated to correspond to draft-ietf-mpls-ldp-06.txt of
the LDP Specification [18].
The front section was updated.
The MIB was made to be less ATM-centric. Essentially, the ATM
specific objects where removed from the tables and placed in ATM
specific Tables. A "type" was added to the "base" tables and a row
is to be created in the ATM/FR/etc. "type" table. Apropos
compliance statements were added to reflect the separation of ATM and
Frame Relay objects into their respective tables.
Objects for Loop Detection were removed from describing the LDP
implementation (i.e. the scalars were removed) and Loop Dection
objects were added to the Session Table. (Although as the LDP
Specification indicates loop detection should be for an LSR within a
domain.)
The following tables were added: mplsLdpEntityAtmParmsTable,
mplsLdpEntityConfAtmLabelRangeTable, mplsLdpFrameRelayParmsTable,
mplsLdpConfFrLabelRangeTable, mplsLdpAtmSessionTable,
mpslLdpFrameRelaySessionTable, mplsLdpSessionPeerAddressTable,
mplsLdpLibTable, and the mplsLdpFecTable.
The following notifications were added: notification for Session
removal.
The following objects were removed from the Session Table:
mplsLdpSessionRole was removed (this can be determined by comparing
LSR Ids and does not need to be explicitely in the MIB.) ATM
specific objects (mplsLdpSessionAtmLabelRangeLowerBoundVpi
mplsLdpSessionAtmLabelRangeLowerBoundVci,
mplsLdpSessionAtmLabelRangeUpperBoundVpi
Expires September 2000 [Page 67]
INTERNET-DRAFT MPLS LDP MIB March 2000
mplsLdpSessionAtmLabelRangeUpperBoundVci) were removed and put into a
separate table. Frame Relay objects were added in a separate table.
Hello Adjacency Table was updated.
The objects, mplsLdpSessionRejectedParamErrors,
mplsLdpSessionRejectedNoHelloErrors, mplsLdpBadLdpIdentifierErrors,
mplsLdpBadPduLengthErrors, mplsLdpBadMessageLengthErrors,
mplsLdpBadTlvLengthErrors, mplsLdpMalformedTlvValueErrors,
mplsLdpKeepAliveTimerExpiredErrors, mplsLdpShutdownNotifReceived, and
mplsLdpShutdownNotifSent were added to the mplsLdpEntityStatsTable.
The mplsLdpSessionStatsTable was added to count statics based on a
per Session basis.
The mplLdpPeerConfAtmLabelRangeTable has been removed. There is no
need to configure information for a Peer. All information for a peer
is learned, thus peer information is read-only.
(Editorial) References were updated to reflect the documents which
this version was based on.
5.5. Changes from <draft-ietf-mpls-ldp-mib-00.txt>
Textual conventions were added for the LSR Identifier and the LDP
Identifier.
Top-level mib structure was added. The LDP MIB falls under a proposed
hierarchy of mpls.mplsProtocols.
The mib hierarchy within the LDP MIB was also changed. A new branch,
under mpls.mplsProtocols.mplsLdpMIB.mplsLdpObjects was added. This
branch is mplsLdpLsrObjects. Currently, this contains several new
scalar objects: mplsLdpLsrID, mplsLdpLsrLoopDetectionPresent,
mplsLdpLsrLoopDetectinAdminStatus, mplsLdpLsrPathVectorLimit,
mplsLdpLsrHopCountLimit, mplsLdpLsrLoopPreventionPresent,
mplsLdpLsrLoopPreventionAdminStatus, and
mplsLdpLsrLabelRetentionMode.
mplsLdpEntityTable is now indexed by mplsLdpEntityIdentifier, which
is the LDP Identifier used in Session establishment.
mplsLdpEntityLoopDetection and mplsLdpEntityLoopPrevention objects
were removed from this table.
The following objects were added to the mplsLdpEntityTable:
mplsLdpEntityLabelSpaceType, mplsLdpEntityUnlabTrafVpi,
mplsLdpEntityUnlabTrafVci, mplsLdpEntityMergeCapability,
mplsLdpEntityVcDirectionality, and
mplsLdpEntityLabelDistributionMethod.
Expires September 2000 [Page 68]
INTERNET-DRAFT MPLS LDP MIB March 2000
The following objects were added to the mplsLdpPeerEntityTable:
mplsLdpPeerLabelDistributionMethod.
The following object was removed from the mplsLdpEntityStatsTable:
mplsLdpEntityEstablishedSessions.
References were added and revised.
6. TO DO List
This section should be removed when this document is published as an
RFC. This section outlines the next areas the authors intend to
address in subsequent revisions.
o Remove the following sections prior to final publication:
Revisions Section and this (TO DO List) Section.
o Updates as suggested by review of working group.
7. Acknowledgments
The authors would like to thank the following people: Leigh
McLellan, Geetha Brown, Geping Chen and Charlan Zhou from Nortel
Networks, and Zoltan Takacs and Bo Augustsson from Ericsson. Also,
some members of the working group were very helpful with comments and
corrections to the MIB; the authors would like to thank Adrian Farrel
of Data Connection, and Alan Kullberg from Harris & Jeffries.
Expires September 2000 [Page 69]
INTERNET-DRAFT MPLS LDP MIB March 2000
8. References
[RFC2571] Harrington, D., Presuhn, R., and B. Wijnen, "An Architecture
for Describing SNMP Management Frameworks", RFC 2571, April
1999.
[RFC1155] Rose, M., and K. McCloghrie, "Structure and Identification
of Management Information for TCP/IP-based Internets", STD
16, RFC 1155, May 1990.
[RFC1212] Rose, M., and K. McCloghrie, "Concise MIB Definitions", STD
16, RFC 1212, March 1991.
[RFC1215] M. Rose, "A Convention for Defining Traps for use with the
SNMP", RFC 1215, March 1991.
[RFC2578] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J.,
Rose, M., and S. Waldbusser, "Structure of Management
Information Version 2 (SMIv2)", STD 58, RFC 2578, April
1999.
[RFC2579] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J.,
Rose, M., and S. Waldbusser, "Textual Conventions for
SMIv2", STD 58, RFC 2579, April 1999.
[RFC2580] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J.,
Rose, M., and S. Waldbusser, "Conformance Statements for
SMIv2", STD 58, RFC 2580, April 1999.
[RFC1157] Case, J., Fedor, M., Schoffstall, M., and J. Davin, "Simple
Network Management Protocol", STD 15, RFC 1157, May 1990.
[RFC1901] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser,
"Introduction to Community-based SNMPv2", RFC 1901, January
1996.
[RFC1906] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser,
"Transport Mappings for Version 2 of the Simple Network
Management Protocol (SNMPv2)", RFC 1906, January 1996.
[RFC2572] Case, J., Harrington D., Presuhn R., and B. Wijnen, "Message
Processing and Dispatching for the Simple Network Management
Protocol (SNMP)", RFC 2572, April 1999.
[RFC2574] Blumenthal, U., and B. Wijnen, "User-based Security Model
(USM) for version 3 of the Simple Network Management
Protocol (SNMPv3)", RFC 2574, April 1999.
[RFC1905] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser,
"Protocol Operations for Version 2 of the Simple Network
Expires September 2000 [Page 70]
INTERNET-DRAFT MPLS LDP MIB March 2000
Management Protocol (SNMPv2)", RFC 1905, January 1996.
[RFC2573] Levi, D., Meyer, P., and B. Stewart, "SNMPv3 Applications",
RFC 2573, April 1999.
[RFC2575] Wijnen, B., Presuhn, R., and K. McCloghrie, "View-based
Access Control Model (VACM) for the Simple Network
Management Protocol (SNMP)", RFC 2575, April 1999.
[RFC2570] Case, J., Mundy, R., Partain, D., and B. Stewart,
"Introduction to Version 3 of the Internet-standard Network
Management Framework", RFC 2570, April 1999.
[17] Narten, T., and H. Alvestrand, "Guidelines for Writing an IANA
Considerations Section in RFCs.", RFC 2434, IBM, Maxware, October
1998
[18] Andersson, L., Doolan, P., Feldman, N., Fredette, A., and Thomas,
B., "LDP Specification.", draft-ietf-mpls-ldp-06.txt, Nortel
Networks, Ennovate Networks, IBM, Nortel Networks, Cisco Systems
October 1999
[19] Callon, R., Doolan, P., Feldman, N., Fredette, A., Swallow, G., and
A. Viswanathan, "A Framework for Multiprotocol Label Switching",
draft-ietf-mpls-framework-05.txt, IronBridge Networks, Ennovate
Networks, IBM, Nortel Networks, Cisco Systems, September 1999.
[20] Rosen, E., Viswananthan, A., and R. Callon, "Multiprotocol Label
Switching Architecture", draft-ietf-mpls-arch-06.txt, Cisco
Systems, Lucent Technologies, and IronBridge Networks, August 1999.
[21] Jamoussi, B., editor, "Constraint-Based LSP Setup using LDP",
draft-ietf-mpls-cr-ldp-03.txt, September 1999.
[22] Bradner, S., "Key words for use in RFCs to Indicate Requirement
Levels", BCP 14, RFC 2119, Harvard University, March 1997
[23] Bradner, S., "The Internet Standards Process -- Revision 3", BCP 9,
RFC 2026, Harvard University, October 1996
[24] Srinivansan, C., and A. Viswanathan, "MPLS Traffic Engineering
Management Information Base Using SMIv2", draft-ietf-mpls-te-mib-
01.txt, Lucent Technologies, June 1999.
[25] Srinivansan, C., Viswanathan, A., and T. Nadeau "MPLS Label Switch
Router Management Information Base Using SMIv2", draft-ietf-mpls-
lsr-mib-01.txt, Tachion Networks, Force10 Networks, cisco, June
1999.
Expires September 2000 [Page 71]
INTERNET-DRAFT MPLS LDP MIB March 2000
[26] Greene, M., Cucchiara, J., and J. Luciani, "Definition of Managed
Objects for the NBMA Next Hop Resolution Protocol (NHRP)", RFC
2677, August 1999.
[27] Internet Assigned Numbers Authority (IANA), ADDRESS FAMILY NUMBERS,
(http://www.isi.edu/in-notes/iana/assignements/address-family-
numbers), for MIB
(ftp://ftp.isi.edu/mib/ianaaddressfamilynumbers.mib).
[28] Noto, M., E. Spiegel, K. Tesink, "Definition of Textual Conventions
and OBJECT-IDENTITIES for ATM Management", RFC 2514, February 1999.
[29] McCloghrie, K., F. Kastenholz, "The Interfaces Group MIB using
SMIv2", RFC 2233, November 1997.
[30] Tesink, K. (ed.) "Definitions of Managed Objects for ATM
Management", RFC 2515, February 1999.
[31] Grossman, D., and J. Heinanen, "Multiprotocol Encapsulation over
ATM Adaptation Layer 5", RFC 2684, September 1999.
[32] Davie, B., J. Lawrence, K. McCloghrie, Y. Rekhter, E. Rosen, G.
Swallow, and P. Doolan, "MPLS using LDP and ATM VC Switching",
draft-ietf-mpls-atm-02.txt, April 1999.
[33] Rosen, E., Rekhter, Y., Tappan, D., Farinacci, D., Fedorkow, G.,
Li, T., and A. Conta, "MPLS Label Stack Encoding", draft-ietf-
mpls-label-encaps-07.txt, September 1999.
[34] Conta, A., Doolan, P., and A. Malis, "Use of Label Switching on
Frame Relay Networks Specification", draft-ietf-mpls-fr-03.txt,
November 1998.
9. Security Considerations
There are a number of management objects defined in this MIB that have a
MAX-ACCESS clause of read-write and/or read-create. Such objects may
be considered sensitive or vulnerable in some network environments.
The support for SET operations in a non-secure environment without
proper protection can have a negative effect on network operations.
There are a number of managed objects in this MIB that may contain
sensitive information. These are contained in the mplsLdpEntityTable.
The objects contained in this table are responsible for setting up or
tearing down LSPs.
Expires September 2000 [Page 72]
INTERNET-DRAFT MPLS LDP MIB March 2000
It is thus important to control even GET access to these objects and
possibly to even encrypt the values of these object when sending them
over the network via SNMP. Not all versions of SNMP provide features
for such a secure environment.
SNMPv1 by itself is not a secure environment. Even if the network
itself is secure (for example by using IPSec), even then, there is no
control as to who on the secure network is allowed to access and
GET/SET (read/change/create/delete) the objects in this MIB.
It is recommended that the implementers consider the security
features as provided by the SNMPv3 framework. Specifically, the use
of the User-based Security Model RFC 2574 [RFC2574] and the View-
based Access Control Model RFC 2575 [RFC2575] is recommended.
It is then a customer/user responsibility to ensure that the SNMP
entity giving access to an instance of this MIB, is properly
configured to give access to the objects only to those principals
(users) that have legitimate rights to indeed GET or SET
(change/create/delete) them.
10. Authors' Addresses
James V. Luciani
TollBridge Technologies
PO BOX 1010
Concord, MA 01742
Email: jluciani@tollbridgetech.com
Hans Sjostrand
Ericsson
Business Unit Datacom Networks and IP Services
S-126 25 Stockholm, Sweden
Phone: +46 8 719 9960
Email: hans.sjostrand@etx.ericsson.se
Joan Cucchiara
Brix Networks
300 Concord Ave.
Billerica, MA 01821
Phone: (978) 439-1523
Email: jcucchiara@brixnet.com
Expires September 2000 [Page 73]
INTERNET-DRAFT MPLS LDP MIB March 2000
11. Full Copyright Statement
Copyright (C) The Internet Society (1999). All Rights Reserved.
This document and translations of it may be copied and furnished to
others, and derivative works that comment on or otherwise explain it
or assist in its implementation may be prepared, copied, published
and distributed, in whole or in part, without restriction of any
kind, provided that the above copyright notice and this paragraph are
included on all such copies and derivative works. However, this
document itself may not be modified in any way, such as by removing
the copyright notice or references to the Internet Society or other
Internet organizations, except as needed for the purpose of
developing Internet standards in which case the procedures for
copyrights defined in the Internet Standards process must be
followed, or as required to translate it into languages other than
English.
The limited permissions granted above are perpetual and will not be
revoked by the Internet Society or its successors or assigns.
This document and the information contained herein is provided on an
"AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Expires September 2000 [Page 74]
INTERNET-DRAFT MPLS LDP MIB March 2000