Internet Draft
Definitions of Managed Objects for
the Multiprotocol Label Switching, Label Distribution Protocol (LDP)
June 1999
<draft-ietf-mpls-ldp-mib-01.txt>
Joan Cucchiara Hans Sjostrand James V. Luciani
IronBridge Networks Ericsson Nortel Networks
Status of this Memo
This document is an Internet-Draft and is in full conformance with
all provisions of Section 10 of RFC 2026. Internet-Drafts are
working documents of the Internet Engineering Task Force (IETF), its
areas, and its working groups. Note that other groups may also
distribute working documents as Internet-Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress".
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html
Distribution of this document is unlimited. Please send comments to
the Multiprotocol Label Switching (mpls) Working Group,
.
Copyright Notice
Copyright (C) The Internet Society (1999). All Rights Reserved.
Abstract
This memo defines a portion of the Management Information Base (MIB)
for use with network management protocols in the Internet community.
In particular, it describes managed objects for the Multiprotocol
Label Switching, Label Distribution Protocol (LDP).
Expires December 1999 [Page 1]
INTERNET-DRAFT MPLS LDP MIB June 1999
Table of Contents
1 Introduction ................................................. 3
2 The SNMP Management Framework ................................ 3
3 Structure of the MIB ......................................... 5
3.1 The MPLS LDP General Group ................................. 5
3.1.1 The Label Distribution Protocol's Entity Table ........... 5
Table ..................................................... 5
3.1.3 The LDP Peer Table ....................................... 5
3.1.4 The LDP Sessions Table ................................... 6
3.1.5 The LDP Adjacencies Table ................................ 6
3.1.6 The LDP Label Information Base (LIB) Table ............... 6
3.2 The LDP Notifications Group ................................ 6
3.2.1 LDP Notifications ........................................ 6
4 MPLS Label Distribution Protocol MIB Definitions ............. 6
5 Revision History ............................................. 29
5.1 Changes from <draft-ietf-mpls-ldp-mib-00.txt> .............. 29
6 TO DO List ................................................... 29
7 Acknowledgments .............................................. 30
8 References ................................................... 31
9 Security Considerations ...................................... 33
10 Authors' Addresses .......................................... 33
11 Full Copyright Statement .................................... 33
12 IANA Address Family Numbers MIB ............................. 34
Expires December 1999 [Page 2]
INTERNET-DRAFT MPLS LDP MIB June 1999
1. Introduction
This memo defines a portion of the Management Information Base (MIB)
for use with network management protocols in the Internet community.
In particular, it describes managed objects for the Multiprotocol
Label Switching, Label Distribution Protocol (LDP) [18].
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [22].
2. The SNMP Management Framework
The SNMP Management Framework presently consists of five major
components:
o An overall architecture, described in RFC 2571 [RFC2571].
o Mechanisms for describing and naming objects and events for the
purpose of management. The first version of this Structure of
Management Information (SMI) is called SMIv1 and described in
STD 16, RFC 1155 [RFC1155], STD 16, RFC 1212 [RFC1212] and RFC
1215 [RFC1215]. The second version, called SMIv2, is described
in STD 58, RFC 2578 [RFC2578], RFC 2579 [RFC2579] and RFC 2580
[RFC2580].
o Message protocols for transferring management information. The
first version of the SNMP message protocol is called SNMPv1 and
described in STD 15, RFC 1157 [RFC1157]. A second version of the
SNMP message protocol, which is not an Internet standards track
protocol, is called SNMPv2c and described in RFC 1901 [RFC1901]
and RFC 1906 [RFC1906]. The third version of the message
protocol is called SNMPv3 and described in RFC 1906 [RFC1906],
RFC 2572 [RFC2572] and RFC 2574 [RFC2574].
o Protocol operations for accessing management information. The
first set of protocol operations and associated PDU formats is
described in STD 15, RFC 1157 [RFC1157]. A second set of
protocol operations and associated PDU formats is described in
RFC 1905 [RFC1905].
o A set of fundamental applications described in RFC 2573
[RFC2573] and the view-based access control mechanism described
in RFC 2575 [RFC2575].
A more detailed introduction to the current SNMP Management Framework
can be found in RFC 2570 [RFC2570].
Managed objects are accessed via a virtual information store, termed
Expires December 1999 [Page 3]
INTERNET-DRAFT MPLS LDP MIB June 1999
the Management Information Base or MIB. Objects in the MIB are
defined using the mechanisms defined in the SMI.
This memo specifies a MIB module that is compliant to the SMIv2. A
MIB conforming to the SMIv1 can be produced through the appropriate
translations. The resulting translated MIB must be semantically
equivalent, except where objects or events are omitted because no
translation is possible (use of Counter64). Some machine readable
information in SMIv2 will be converted into textual descriptions in
SMIv1 during the translation process. However, this loss of machine
readable information is not considered to change the semantics of the
MIB.
Expires December 1999 [Page 4]
INTERNET-DRAFT MPLS LDP MIB June 1999
3. Structure of the MIB
The following aspects are not addressed in this document: Interfaces
with respect to the IFMIB (e.g. is ldp an interface in the sense of
being stacked onto of the data link layer, and its relationship to
the network layer), VPN issues (i.e. potential MIB objects such as
the VPN Identifier are not included at this time), and lastly,
multicast issues are not discussed.
Some of these issues need further clarification before adding to this
MIB.
Currently, there is two groups. The MPLS LDP General Group and the
MPLS LDP Notifications Group.
3.1. The MPLS LDP General Group
This group contains information about the specific LDP Entities which
are associated with this agent. Each LSR must have one LDP Entity.
3.1.1. The Label Distribution Protocol's Entity Table
The LDP Entity Table represents the LDP Entities which exist on a
single Label Switch Router (LSR). The LDP Entity performs the LDP
protocol. There must be at least one LDP Entity for the LSR to
support LDP.
Each entry/row in this table represents a single LDP Entity.
3.1.2. The Label Distribution Protocol's Entity Statistics Table
The LDP Entity Statistics Table will maintain counters related to an
LDP Entity. This Table should be a read-only table which contains
statistical information.
Each row in this table will be related to a single LDP Entity.
3.1.3. The LDP Peer Table
The LDP Peer Table contains information about LDP Peers. Each row in
this table represents an LDP Peer which is known to an LDP Entity.
Expires December 1999 [Page 5]
INTERNET-DRAFT MPLS LDP MIB June 1999
3.1.4. The LDP Sessions Table
Each entry in this table represents a session between an LDP Entity
and a Peer.
3.1.5. The LDP Adjacencies Table
This is a table of all adjacencies between all LPD Entities and all
LDP Peers. A Session may have one or more adjacencies.
3.1.6. The LDP Label Information Base (LIB) Table
TBD. Some potential objects: incoming label, outgoing label, and the
mid.
3.2. The LDP Notifications Group
3.2.1. LDP Notifications
Currently, there is one notification which will be sent when an LDP
attempts to initialize the same session beyond the configured
threshold.
4. MPLS Label Distribution Protocol MIB Definitions
MPLS-LDP-MIB DEFINITIONS ::= BEGIN
IMPORTS
OBJECT-TYPE, MODULE-IDENTITY, NOTIFICATION-TYPE,
experimental,
Integer32, Counter32, Unsigned32
FROM SNMPv2-SMI
MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP
FROM SNMPv2-CONF
TEXTUAL-CONVENTION, TruthValue, RowStatus, TimeInterval
FROM SNMPv2-TC
ifIndex
FROM IF-MIB
AddressFamilyNumbers
FROM IANA-ADDRESS-FAMILY-NUMBERS-MIB
;
Expires December 1999 [Page 6]
INTERNET-DRAFT MPLS LDP MIB June 1999
mplsLdpMIB MODULE-IDENTITY
LAST-UPDATED "9906301200Z" -- June 30, 1999
ORGANIZATION "Multiprotocol Label Switching (mpls) Working Group"
CONTACT-INFO
"Joan Cucchiara (joan@ironbridgenetworks.com)
IronBridge Networks
Hans Sjostrand (hans.sjostrand@etx.ericsson.se)
Ericsson
James V. Luciani (luciani@baynetworks.com)
Nortel Networks"
DESCRIPTION
"This MIB contains managed object definitions for the
Multiprotocol Label Switching, Label Distribution
Protocol, LDP, as defined in draft-ietf-mpls-ldp-04.txt."
::= { experimental 9876 } -- to be assigned
--********************************************************************
-- MPLS LDP Textual Conventions
--********************************************************************
--
MplsLsrIdentifier ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The Label Switch Router (LSR) identifier
is the first 4 bytes or the IP Address component
of the Label Distribution Protocol (LDP) identifier."
SYNTAX OCTET STRING (SIZE (4))
MplsLdpGenAddr ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The value of an network layer or data link layer address."
SYNTAX OCTET STRING (SIZE (0..64))
MplsLdpIdentifier ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The LDP identifier is a six octet quantity
which is used to identify an Label Switch Router
(LSR) label space.
The first four octets encode an IP address
assigned to the LSR, and the last two octets
identify a specific label space within the LSR."
SYNTAX OCTET STRING (SIZE (6))
Expires December 1999 [Page 7]
INTERNET-DRAFT MPLS LDP MIB June 1999
AtmVpIdentifier ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The VPI value for a VPL. The value VPI=0 is not
used for a VPL not associated with a VCL. For ATM
UNIs supporting VPCs the VPI value ranges from 1
to 255. For ATM UNIs supporting VCCs the VPI value
ranges from 0 to 255. The maximum VPI value
cannot exceed the value allowable by
atmInterfaceMaxVpiBits defined in ATM-MIB."
SYNTAX Unsigned32 (0..4095)
AtmVcIdentifier ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The VCI value for a VCL. The maximum VCI value
cannot exceed the value allowable by
atmInterfaceMaxVciBits defined in ATM-MIB."
SYNTAX Unsigned32 (0..65535)
-- Top-level structure of the MIB (the following is proposed)
mpls OBJECT IDENTIFIER ::= { mplsProtocols }
mplsProtocols OBJECT IDENTIFIER ::= { mplsLdpObjects }
-- under mplsProtocols will be LDP, CR-LDP,
-- and other MPLS "Protocols".
mplsLdpObjects OBJECT IDENTIFIER ::= { mplsLdpMIB 1 }
mplsLdpNotifications OBJECT IDENTIFIER ::= { mplsLdpMIB 2 }
mplsLdpConformance OBJECT IDENTIFIER ::= { mplsLdpMIB 3 }
--****************************************************************
-- MPLS LDP Objects
--****************************************************************
mplsLdpLsrObjects OBJECT IDENTIFIER ::= { mplsLdpObjects 1 }
mplsLdpEntityObjects OBJECT IDENTIFIER ::= { mplsLdpObjects 2 }
--
-- The MPLS Label Distribution Protocol Label Switch Router Objects
--
mplsLdpLsrID OBJECT-TYPE
SYNTAX MplsLsrIdentifier
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The LSR's Identifier."
Expires December 1999 [Page 8]
INTERNET-DRAFT MPLS LDP MIB June 1999
::= { mplsLdpLsrObjects 1 }
mplsLdpLsrLoopDetectionPresent OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A indication of whether this LSR supports
loop detection. A value of 'true' indicates
this LSR does support loop detection. A value
of 'false' indicates this LSR does not support
loop detection."
::= { mplsLdpLsrObjects 2 }
mplsLdpLsrLoopDetectionAdminStatus OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"To enable loop detection the value of
this object should be 'enabled(1)'.
Otherwise, to turn off loop detection,
set this value to 'disabled(2)'."
::= { mplsLdpLsrObjects 3 }
mplsLdpLsrPathVectorLimit OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object only has meaning if
mplsLdpLsrLoopDetectionPresent has
the value of 'true'.
The value of this object represents the
limit of path vectors which this LSR uses
to treat the message as if it had
traversed a loop."
::= { mplsLdpLsrObjects 4 }
mplsLdpLsrHopCountLimit OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object only has meaning if
mplsLdpLsrLoopDetectionPresent has
Expires December 1999 [Page 9]
INTERNET-DRAFT MPLS LDP MIB June 1999
the value of 'true'.
The value of this object represents the
limit on the Hop Count which this LSR uses
to treat the message as if it had
traversed a loop."
::= { mplsLdpLsrObjects 5 }
mplsLdpLsrLoopPreventionPresent OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A indication of whether this LSR supports
loop prevention. A value of 'true' indicates
this LSR does support loop prevention. A value
of 'false' indicates this LSR does not support
loop prevention."
::= { mplsLdpLsrObjects 6 }
mplsLdpLsrLoopPreventionAdminStatus OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"To enable loop prevention the value of
this object should be 'enabled(1)'.
Otherwise, to turn off loop prevention,
set this value to 'disabled(2)'."
::= { mplsLdpLsrObjects 7 }
mplsLdpLsrLabelRetentionMode OBJECT-TYPE
SYNTAX INTEGER {
conservative(1),
liberal(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The LSR can be configured to use either
conservative or liberal label retention mode.
If the value of this object is conservative(1)
then advertized label mappings are retained
only if they will be used to forward packets,
i.e. if label came from a valid next hop.
Expires December 1999 [Page 10]
INTERNET-DRAFT MPLS LDP MIB June 1999
If the value of this object is liberal(2)
then all advertized label mappings are retained
whether they are from a valid next hop or not."
::= { mplsLdpLsrObjects 8 }
--
-- The MPLS Label Distribution Protocol Entity Table
--
mplsLdpEntityTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsLdpEntityEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains information about the
MPLS Label Distribution Protocol Entities which
exist on this Label Switch Router (LSR)."
::= { mplsLdpEntityObjects 1 }
mplsLdpEntityEntry OBJECT-TYPE
SYNTAX MplsLdpEntityEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table represents an LDP entity.
An entry can be created by a network administrator
or by an SNMP agent as instructed by LDP.
An LPD Entity is uniquely indexed by its LPD
Identifier."
INDEX { mplsLdpEntityID }
::= { mplsLdpEntityTable 1 }
MplsLdpEntityEntry ::= SEQUENCE {
mplsLdpEntityID MplsLdpIdentifier,
mplsLdpEntityLabelSpaceType INTEGER,
mplsLdpEntityDefVpi AtmVpIdentifier,
mplsLdpEntityDefVci AtmVcIdentifier,
mplsLdpEntityUnlabTrafVpi AtmVpIdentifier,
mplsLdpEntityUnlabTrafVci AtmVcIdentifier,
mplsLdpEntityMergeCapability INTEGER,
mplsLdpEntityVcDirectionality INTEGER,
mplsLdpEntityWellKnownDiscoveryPort Unsigned32,
mplsLdpEntityMtu Integer32,
mplsLdpEntityKeepAliveHoldTimer Integer32,
mplsLdpEntityFailedInitSessionThreshold Integer32,
mplsLdpEntityLabelDistributionMethod INTEGER,
mplsLdpEntityRowStatus RowStatus
}
Expires December 1999 [Page 11]
INTERNET-DRAFT MPLS LDP MIB June 1999
mplsLdpEntityID OBJECT-TYPE
SYNTAX MplsLdpIdentifier
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The LDP identifier which uniquely identifies
the LDP Entity. This is s six octet quantity
which is used to identify an Label Switch Router
(LSR) label space.
The first four octets encode an IP address
assigned to the LSR, and the last two octets
identify a specific label space within the
LSR."
REFERENCE
"LDP Specification, Section on LDP Identifiers."
::= { mplsLdpEntityEntry 1 }
mplsLdpEntityLabelSpaceType OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
perInterface(2),
perPlatform(3)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The type of label spaces associated with this
LDP Entity. The values are
'unknown(1)' The type of label space is
not known.
'perInterface(2)' The type of label space is
tied to an interface.
'perPlatform(3)' The type of label space is
tied to the platform."
REFERENCE
"LDP Specification, Section on Label Spaces."
::= { mplsLdpEntityEntry 2 }
mplsLdpEntityDefVpi OBJECT-TYPE
SYNTAX AtmVpIdentifier
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The Default VPI value used in the label for the default
VPI."
::= { mplsLdpEntityEntry 3 }
Expires December 1999 [Page 12]
INTERNET-DRAFT MPLS LDP MIB June 1999
mplsLdpEntityDefVci OBJECT-TYPE
SYNTAX AtmVcIdentifier
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The Default VCI value used in the label for the default
VCI."
::= { mplsLdpEntityEntry 4 }
mplsLdpEntityUnlabTrafVpi OBJECT-TYPE
SYNTAX AtmVpIdentifier
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"VPI value of the VCC supporting unlabeled traffic."
DEFVAL { 0 }
::= { mplsLdpEntityEntry 5 }
mplsLdpEntityUnlabTrafVci OBJECT-TYPE
SYNTAX AtmVcIdentifier
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"VCI value of the VCC supporting unlabeled traffic."
DEFVAL { 31 }
::= { mplsLdpEntityEntry 6 }
mplsLdpEntityMergeCapability OBJECT-TYPE
SYNTAX INTEGER {
noMerge(0),
vpMerge(1),
vcMerge(2),
vpVcMerge(3)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Sets the merge capability for this LDP entity."
REFERENCE
"draft-ietf-mpls-ldp-04.txt, Section 3.5.3"
::= { mplsLdpEntityEntry 7 }
mplsLdpEntityVcDirectionality OBJECT-TYPE
SYNTAX INTEGER {
bidirectional(1),
unidirectional(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
Expires December 1999 [Page 13]
INTERNET-DRAFT MPLS LDP MIB June 1999
"Sets the VC directionality for this LDP entity."
REFERENCE
"draft-ietf-mpls-ldp-04.txt, Section 3.5.3"
::= { mplsLdpEntityEntry 8 }
mplsLdpEntityWellKnownDiscoveryPort OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The well known LDP Discovery Port."
::= { mplsLdpEntityEntry 9 }
mplsLdpEntityMtu OBJECT-TYPE
SYNTAX Integer32 (0..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum transmission unit (MTU) that was configured
for this entity."
::= { mplsLdpEntityEntry 10 }
mplsLdpEntityKeepAliveHoldTimer OBJECT-TYPE
SYNTAX Integer32 (1..65535)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The two octet value which is the proposed keep alive hold
timer for this LDP Entity."
::= { mplsLdpEntityEntry 11 }
mplsLdpEntityFailedInitSessionThreshold OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"When attempting to establish a session with a
given Peer, the given LDP Entity should
send out a notification when exceeding this threshold.
A value of 0 (zero) for this object
indicates that the threshold is infinity.
In other words, a notification will not
be sent if the value of this object is 0 (zero)."
::= { mplsLdpEntityEntry 12 }
mplsLdpEntityLabelDistributionMethod OBJECT-TYPE
SYNTAX INTEGER {
downstreamOnDemand(1),
Expires December 1999 [Page 14]
INTERNET-DRAFT MPLS LDP MIB June 1999
downstreamUnsolicited(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"For any given LDP session, the method of
label distribution must be specified."
REFERENCE
"draft-ietf-mpls-arch-04.txt [20]."
::= { mplsLdpEntityEntry 13 }
mplsLdpEntityRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An object that allows entries in this table to
be created and deleted using the
RowStatus convention."
::= { mplsLdpEntityEntry 14 }
--
-- The MPLS LDP Entity Configurable ATM Label Range Table
--
mplsLdpEntityConfAtmLabelRangeTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsLdpEntityConfAtmLabelRangeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The MPLS LDP Entity Configurable ATM Label Range Table.
The purpose of this table is to provide a mechanism
for specifying a contiguous range of vpi's
with a contiguous range of vci's, or a 'label range'
for LDP Entities.
LDP Entities which use ATM must have at least one
entry in this table."
::= { mplsLdpEntityObjects 2 }
mplsLdpEntityConfAtmLabelRangeEntry OBJECT-TYPE
SYNTAX MplsLdpEntityConfAtmLabelRangeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A row in the LDP Entity Configurable ATM Label
Range Table. One entry in this table contains
information on a single range of labels
represented by the configured Upper and Lower
Bounds VPI/VCI pairs.
Expires December 1999 [Page 15]
INTERNET-DRAFT MPLS LDP MIB June 1999
NOTE: The ranges for a specific LDP Entity
are UNIQUE and non-overlapping. For example,
for a specific LDP Entity index, there could
be one entry having ConfLowerBound vpi/vci == 0/32, and
ConfUpperBound vpi/vci == 0/100, and a second entry for this
same interface with ConfLowerBound vpi/vci == 0/101 and
ConfUpperBound vpi/vci == 0/200. However, there could not be
a third entry with ConfLowerBound vpi/vci == 0/200 and
ConfUpperBound vpi/vci == 0/300 because this label range overlaps
with the second entry (i.e. both entries now have 0/200).
A row will not be created unless a unique and non-overlapping
range is specified. Thus, row creation implies a one-shot
row creation of LDP EntityID and ConfLowerBound vpi/vci and
ConfUpperBound vpi/vci. At least one label range entry
for a specific LDP Entity MUST include the default VPI/VCI
values denoted in the LDP Entity Table."
INDEX { mplsLdpEntityID,
mplsLdpEntityConfAtmLabelRangeLowerBoundVPI,
mplsLdpEntityConfAtmLabelRangeLowerBoundVCI }
::= { mplsLdpEntityConfAtmLabelRangeTable 1 }
MplsLdpEntityConfAtmLabelRangeEntry ::= SEQUENCE {
mplsLdpEntityConfAtmLabelRangeLowerBoundVPI AtmVpIdentifier,
mplsLdpEntityConfAtmLabelRangeLowerBoundVCI AtmVcIdentifier,
mplsLdpEntityConfAtmLabelRangeUpperBoundVPI AtmVpIdentifier,
mplsLdpEntityConfAtmLabelRangeUpperBoundVCI AtmVcIdentifier,
mplsLdpEntityConfAtmLabelRangeRowStatus RowStatus
}
mplsLdpEntityConfAtmLabelRangeLowerBoundVPI OBJECT-TYPE
SYNTAX AtmVpIdentifier
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The minimum VPI number configured for this range."
::= { mplsLdpEntityConfAtmLabelRangeEntry 1 }
mplsLdpEntityConfAtmLabelRangeLowerBoundVCI OBJECT-TYPE
SYNTAX AtmVcIdentifier
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The minimum VCI number configured for this range."
::= { mplsLdpEntityConfAtmLabelRangeEntry 2 }
mplsLdpEntityConfAtmLabelRangeUpperBoundVPI OBJECT-TYPE
SYNTAX AtmVpIdentifier
MAX-ACCESS read-create
STATUS current
Expires December 1999 [Page 16]
INTERNET-DRAFT MPLS LDP MIB June 1999
DESCRIPTION
"The maximum VPI number configured for this range."
::= { mplsLdpEntityConfAtmLabelRangeEntry 3 }
mplsLdpEntityConfAtmLabelRangeUpperBoundVCI OBJECT-TYPE
SYNTAX AtmVcIdentifier
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum VCI number configured for this range."
::= { mplsLdpEntityConfAtmLabelRangeEntry 4 }
mplsLdpEntityConfAtmLabelRangeRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An object that allows entries in this
table to be created and deleted using
the RowStatus convention."
::= { mplsLdpEntityConfAtmLabelRangeEntry 5 }
--
-- The MPLS LDP Entity Statistics Table
--
mplsLdpEntityStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsLdpEntityStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table is a read-only table which augments
the MplsLdpConfEntityTable. The purpose of this
table is to keep statistical information about
the LDP Entities on the LSR."
::= { mplsLdpEntityObjects 3 }
mplsLdpEntityStatsEntry OBJECT-TYPE
SYNTAX MplsLdpEntityStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A row in this table contains statistical information
about an LDP Entity."
AUGMENTS { mplsLdpEntityEntry }
::= { mplsLdpEntityStatsTable 1 }
MplsLdpEntityStatsEntry ::= SEQUENCE {
mplsLdpAttemptedSessions Counter32
Expires December 1999 [Page 17]
INTERNET-DRAFT MPLS LDP MIB June 1999
}
mplsLdpAttemptedSessions OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A count of the total attempted sessions for
this LDP Entity."
::= { mplsLdpEntityStatsEntry 1 }
--
-- The MPLS LDP Peer Table
--
mplsLdpPeerObjects OBJECT IDENTIFIER ::= { mplsLdpObjects 3 }
mplsLdpPeerTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsLdpPeerEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information about LDP peers which have been discovered
by the LDP Entities that are managed by this agent."
::= { mplsLdpPeerObjects 1 }
mplsLdpPeerEntry OBJECT-TYPE
SYNTAX MplsLdpPeerEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information about a single Peer."
INDEX { mplsLdpEntityID,
mplsLdpPeerIndex }
::= { mplsLdpPeerTable 1 }
MplsLdpPeerEntry ::= SEQUENCE {
mplsLdpPeerIndex Unsigned32,
mplsLdpPeerID MplsLdpIdentifier,
mplsLdpPeerInternetworkAddrType AddressFamilyNumbers,
mplsLdpPeerInternetworkAddr MplsLdpGenAddr,
mplsLdpPeerDefaultMtu Integer32,
mplsLdpPeerKeepAliveHoldTimer Integer32,
mplsLdpPeerLabelDistributionMethod INTEGER,
mplsLdpPeerRowStatus RowStatus
}
mplsLdpPeerIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
Expires December 1999 [Page 18]
INTERNET-DRAFT MPLS LDP MIB June 1999
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An identifier for the LDP peer that is unique within the
scope of this agent."
::= { mplsLdpPeerEntry 1 }
mplsLdpPeerID OBJECT-TYPE
SYNTAX MplsLdpIdentifier
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The LDP identifier of this LDP Peer."
::= { mplsLdpPeerEntry 2 }
mplsLdpPeerInternetworkAddrType OBJECT-TYPE
SYNTAX AddressFamilyNumbers
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The type of the internetwork layer address of this
LDP peer. This object indicates how the value of
mplsLdpPeerInternetworkAddr is to be interpreted."
::= { mplsLdpPeerEntry 3 }
mplsLdpPeerInternetworkAddr OBJECT-TYPE
SYNTAX MplsLdpGenAddr
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of the internetwork layer address of this LDP peer."
::= { mplsLdpPeerEntry 4 }
mplsLdpPeerDefaultMtu OBJECT-TYPE
SYNTAX Integer32 (0..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The default maximum transmission unit (MTU) of the
LDP Peer."
DEFVAL { 9180 }
::= { mplsLdpPeerEntry 5 }
mplsLdpPeerKeepAliveHoldTimer OBJECT-TYPE
SYNTAX Integer32 (1..65535)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The two octet unsigned non zero integer that indicates
Expires December 1999 [Page 19]
INTERNET-DRAFT MPLS LDP MIB June 1999
the number of seconds that this Peer proposes for the
value of the KeepAlive Interval."
::= { mplsLdpPeerEntry 6 }
mplsLdpPeerLabelDistributionMethod OBJECT-TYPE
SYNTAX INTEGER {
downstreamOnDemand(1),
downstreamUnsolicited(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"For any given LDP session, the method of
label distribution must be specified."
REFERENCE
"draft-ietf-mpls-arch-05.txt [20]."
::= { mplsLdpPeerEntry 7 }
mplsLdpPeerRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An object that allows entries in this table to be created
and deleted using the RowStatus convention."
::= { mplsLdpPeerEntry 8 }
--
-- The MPLS LDP Peer Configurable ATM Label Range Table
--
mplsLdpPeerConfAtmLabelRangeTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsLdpPeerConfAtmLabelRangeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The MPLS LDP Peer Configurable ATM Label Range Table.
The purpose of this table is to provide a mechanism
for specifying a contiguous range of vpi's with a contiguous
range of vci's, or a 'label range' for LDP Peers.
LDP Peers which use ATM must have at least one
entry in this table."
::= { mplsLdpPeerObjects 2 }
mplsLdpPeerConfAtmLabelRangeEntry OBJECT-TYPE
SYNTAX MplsLdpPeerConfAtmLabelRangeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A row in the LDP Peer Configurable ATM Label Range Table.
Expires December 1999 [Page 20]
INTERNET-DRAFT MPLS LDP MIB June 1999
One entry in this table contains information
on a single range of labels represented by
the configured Upper and Lower Bounds VPI/VCI pairs.
NOTE: The ranges for a specific LDP Peer
are UNIQUE and non-overlapping. For example,
for a specific LDP Peer index, there could
be one entry having ConfLowerBound vpi/vci == 0/32, and
ConfUpperBound vpi/vci == 0/100, and a second entry for this
same interface with ConfLowerBound vpi/vci == 0/101 and
ConfUpperBound vpi/vci == 0/200. However, there could not be
a third entry with ConfLowerBound vpi/vci == 0/200 and
ConfUpperBound vpi/vci == 0/300 because this label range overlaps
with the second entry (i.e. both entries now have 0/200).
A row will not be created unless a unique and non-overlapping
range is specified. Thus, row creation implies a one-shot
row creation of LDP PeerIndex and ConfLowerBound vpi/vci and
ConfUpperBound vpi/vci. At least one label range entry
for a specific LDP Peer MUST include the default VPI/VCI
values denoted in the LDP Peer Table."
INDEX { mplsLdpPeerIndex,
mplsLdpPeerConfAtmLabelRangeLowerBoundVPI,
mplsLdpPeerConfAtmLabelRangeLowerBoundVCI }
::= { mplsLdpPeerConfAtmLabelRangeTable 1 }
MplsLdpPeerConfAtmLabelRangeEntry ::= SEQUENCE {
mplsLdpPeerConfAtmLabelRangeLowerBoundVPI AtmVpIdentifier,
mplsLdpPeerConfAtmLabelRangeLowerBoundVCI AtmVcIdentifier,
mplsLdpPeerConfAtmLabelRangeUpperBoundVPI AtmVpIdentifier,
mplsLdpPeerConfAtmLabelRangeUpperBoundVCI AtmVcIdentifier,
mplsLdpPeerConfAtmLabelRangeRowStatus RowStatus
}
mplsLdpPeerConfAtmLabelRangeLowerBoundVPI OBJECT-TYPE
SYNTAX AtmVpIdentifier
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The minimum VPI number configured for this range."
::= { mplsLdpPeerConfAtmLabelRangeEntry 1 }
mplsLdpPeerConfAtmLabelRangeLowerBoundVCI OBJECT-TYPE
SYNTAX AtmVcIdentifier
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The minimum VCI number configured for this range."
::= { mplsLdpPeerConfAtmLabelRangeEntry 2 }
Expires December 1999 [Page 21]
INTERNET-DRAFT MPLS LDP MIB June 1999
mplsLdpPeerConfAtmLabelRangeUpperBoundVPI OBJECT-TYPE
SYNTAX AtmVpIdentifier
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum VPI number configured for this range."
::= { mplsLdpPeerConfAtmLabelRangeEntry 3 }
mplsLdpPeerConfAtmLabelRangeUpperBoundVCI OBJECT-TYPE
SYNTAX AtmVcIdentifier
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum VCI number configured for this range."
::= { mplsLdpPeerConfAtmLabelRangeEntry 4 }
mplsLdpPeerConfAtmLabelRangeRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An object that allows entries in this table to be created
and deleted using the RowStatus convention."
::= { mplsLdpPeerConfAtmLabelRangeEntry 5 }
--
-- The MPLS LDP Sessions Table
--
mplsLdpSessionObjects OBJECT IDENTIFIER ::= { mplsLdpObjects 4 }
mplsLdpSessionTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsLdpSessionEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of Sessions between the LDP Entities and
LDP Peers."
::= { mplsLdpSessionObjects 1 }
mplsLdpSessionEntry OBJECT-TYPE
SYNTAX MplsLdpSessionEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table represents information on a
single session between an LDP Entity and LDP Peer."
INDEX { mplsLdpEntityID,
mplsLdpPeerIndex,
mplsLdpSessionIndex
Expires December 1999 [Page 22]
INTERNET-DRAFT MPLS LDP MIB June 1999
}
::= { mplsLdpSessionTable 1 }
MplsLdpSessionEntry ::= SEQUENCE {
mplsLdpSessionIndex Unsigned32,
mplsLdpSessionID MplsLdpIdentifier,
mplsLdpSessionProtocolVersion Integer32,
mplsLdpSessionKeepAliveHoldTimeRemaining TimeInterval,
mplsLdpSessionRole INTEGER,
mplsLdpSessionState INTEGER,
mplsLdpSessionAtmLabelRangeLowerBoundVPI AtmVpIdentifier,
mplsLdpSessionAtmLabelRangeLowerBoundVCI AtmVcIdentifier,
mplsLdpSessionAtmLabelRangeUpperBoundVPI AtmVpIdentifier,
mplsLdpSessionAtmLabelRangeUpperBoundVCI AtmVcIdentifier,
mplsLdpSessionRowStatus RowStatus
}
mplsLdpSessionIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An unique identifier for this entry such that it
identifies a specific LDP Session."
::= { mplsLdpSessionEntry 1 }
mplsLdpSessionID OBJECT-TYPE
SYNTAX MplsLdpIdentifier
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The LDP Session identifier."
::= { mplsLdpSessionEntry 2 }
mplsLdpSessionProtocolVersion OBJECT-TYPE
SYNTAX Integer32(0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The version of the LDP Protocol which
this session is using."
::= { mplsLdpSessionEntry 3 }
mplsLdpSessionKeepAliveHoldTimeRemaining OBJECT-TYPE
SYNTAX TimeInterval
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The keep alive hold time remaining for this session."
::= { mplsLdpSessionEntry 4 }
Expires December 1999 [Page 23]
INTERNET-DRAFT MPLS LDP MIB June 1999
mplsLdpSessionRole OBJECT-TYPE
SYNTAX INTEGER {
active(1),
passive(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An indication of whether the LDP Entity associated with
this session is acting in an 'active' role or
a 'passive' role."
::= { mplsLdpSessionEntry 5 }
mplsLdpSessionState OBJECT-TYPE
SYNTAX INTEGER {
nonexistent(1),
initialized(2),
openrec(3),
opensent(4),
operational(5)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current state of the session, all of the
states 1 - 5 are based on the state machine for
session negotiation behavior."
::= { mplsLdpSessionEntry 6 }
mplsLdpSessionAtmLabelRangeLowerBoundVPI OBJECT-TYPE
SYNTAX AtmVpIdentifier
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The minimum VPI number for this range."
::= { mplsLdpSessionEntry 7 }
mplsLdpSessionAtmLabelRangeLowerBoundVCI OBJECT-TYPE
SYNTAX AtmVcIdentifier
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The minimum VCI number for this range."
::= { mplsLdpSessionEntry 8 }
mplsLdpSessionAtmLabelRangeUpperBoundVPI OBJECT-TYPE
SYNTAX AtmVpIdentifier
MAX-ACCESS read-only
STATUS current
DESCRIPTION
Expires December 1999 [Page 24]
INTERNET-DRAFT MPLS LDP MIB June 1999
"The maximum VPI number for this range."
::= { mplsLdpSessionEntry 9 }
mplsLdpSessionAtmLabelRangeUpperBoundVCI OBJECT-TYPE
SYNTAX AtmVcIdentifier
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum VCI number for this range."
::= { mplsLdpSessionEntry 10 }
mplsLdpSessionRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An object that allows entries in this table to be created
and deleted using the RowStatus convention."
::= { mplsLdpSessionEntry 11 }
--
-- The MPLS LDP Hello Adjacency Table
--
mplsLdpHelloAdjacencyObjects OBJECT IDENTIFIER ::= { mplsLdpObjects 5 }
mplsLdpHelloAdjacencyTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsLdpHelloAdjacencyEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of Hello Adjacencies for Sessions."
::= { mplsLdpHelloAdjacencyObjects 1 }
mplsLdpHelloAdjacencyEntry OBJECT-TYPE
SYNTAX MplsLdpHelloAdjacencyEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each row represents a single LDP Hello Adjacency.
An LDP Session can have one or more Hello adjacencies."
INDEX { mplsLdpSessionIndex,
mplsLdpHelloAdjacencyIndex }
::= { mplsLdpHelloAdjacencyTable 1 }
MplsLdpHelloAdjacencyEntry ::= SEQUENCE {
mplsLdpHelloAdjacencyIndex Unsigned32,
mplsLdpHelloAdjacencyHoldTimeRemaining TimeInterval
}
Expires December 1999 [Page 25]
INTERNET-DRAFT MPLS LDP MIB June 1999
mplsLdpHelloAdjacencyIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An identifier for the adjacency."
::= { mplsLdpHelloAdjacencyEntry 1 }
mplsLdpHelloAdjacencyHoldTimeRemaining OBJECT-TYPE
SYNTAX TimeInterval
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time remaining for this Hello Adjacency."
::= { mplsLdpHelloAdjacencyEntry 2 }
---
--- Notifications
---
mplsLdpNotificationPrefix OBJECT IDENTIFIER ::=
{ mplsLdpNotifications 0 }
mplsLdpFailedInitSessionThresholdExceeded NOTIFICATION-TYPE
OBJECTS {
mplsLdpEntityFailedInitSessionThreshold
}
STATUS current
DESCRIPTION
"This notification is generated whenever the value
of mplsLdpEntityFailedInitSessionThreshold is
exceeded."
::= { mplsLdpNotificationPrefix 1 }
--********************************************************************
-- Module Compliance Statement
--********************************************************************
mplsLdpGroups
OBJECT IDENTIFIER ::= { mplsLdpConformance 1 }
mplsLdpCompliances
OBJECT IDENTIFIER ::= { mplsLdpConformance 2 }
mplsLdpModuleCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for agents that support
Expires December 1999 [Page 26]
INTERNET-DRAFT MPLS LDP MIB June 1999
the MPLS LDP MIB."
MODULE -- this module
MANDATORY-GROUPS { mplsLdpGeneralGroup,
mplsLdpNotificationsGroup
}
OBJECT mplsLdpEntityRowStatus
MIN-ACCESS read-only
DESCRIPTION
"The agent is not required to support a SET operation
to this object."
OBJECT mplsLdpPeerRowStatus
MIN-ACCESS read-only
DESCRIPTION
"The agent is not required to support a SET operation
to this object."
::= { mplsLdpCompliances 1 }
-- units of conformance
mplsLdpGeneralGroup OBJECT-GROUP
OBJECTS {
mplsLdpLsrID,
mplsLdpLsrLoopDetectionPresent,
mplsLdpLsrLoopDetectionAdminStatus,
mplsLdpLsrPathVectorLimit,
mplsLdpLsrHopCountLimit,
mplsLdpLsrLoopPreventionPresent,
mplsLdpLsrLoopPreventionAdminStatus,
mplsLdpLsrLabelRetentionMode,
mplsLdpEntityLabelSpaceType,
mplsLdpEntityDefVpi,
mplsLdpEntityDefVci,
mplsLdpEntityUnlabTrafVpi,
mplsLdpEntityUnlabTrafVci,
mplsLdpEntityMergeCapability,
mplsLdpEntityVcDirectionality,
mplsLdpEntityWellKnownDiscoveryPort,
mplsLdpEntityMtu,
mplsLdpEntityKeepAliveHoldTimer,
mplsLdpEntityFailedInitSessionThreshold,
mplsLdpEntityLabelDistributionMethod,
mplsLdpEntityRowStatus,
mplsLdpEntityConfAtmLabelRangeUpperBoundVPI,
mplsLdpEntityConfAtmLabelRangeUpperBoundVCI,
mplsLdpEntityConfAtmLabelRangeRowStatus,
mplsLdpAttemptedSessions,
mplsLdpPeerID,
mplsLdpPeerInternetworkAddrType,
mplsLdpPeerInternetworkAddr,
Expires December 1999 [Page 27]
INTERNET-DRAFT MPLS LDP MIB June 1999
mplsLdpPeerDefaultMtu,
mplsLdpPeerKeepAliveHoldTimer,
mplsLdpPeerLabelDistributionMethod,
mplsLdpPeerRowStatus,
mplsLdpPeerConfAtmLabelRangeUpperBoundVPI,
mplsLdpPeerConfAtmLabelRangeUpperBoundVCI,
mplsLdpPeerConfAtmLabelRangeRowStatus,
mplsLdpSessionProtocolVersion,
mplsLdpSessionKeepAliveHoldTimeRemaining,
mplsLdpSessionRole,
mplsLdpSessionState,
mplsLdpSessionAtmLabelRangeLowerBoundVPI,
mplsLdpSessionAtmLabelRangeLowerBoundVCI,
mplsLdpSessionAtmLabelRangeUpperBoundVPI,
mplsLdpSessionAtmLabelRangeUpperBoundVCI,
mplsLdpSessionRowStatus,
mplsLdpHelloAdjacencyHoldTimeRemaining
}
STATUS current
DESCRIPTION
"Objects that apply to all MPLS LDP implementations over ATM."
::= { mplsLdpGroups 1 }
mplsLdpNotificationsGroup NOTIFICATION-GROUP
NOTIFICATIONS { mplsLdpFailedInitSessionThresholdExceeded }
STATUS current
DESCRIPTION
"The notification(s) which an MPLS LDP implemention
is required to implement."
::= { mplsLdpGroups 2 }
END
Expires December 1999 [Page 28]
INTERNET-DRAFT MPLS LDP MIB June 1999
5. Revision History
This section should be removed when this document is published as an
RFC.
5.1. Changes from <draft-ietf-mpls-ldp-mib-00.txt>
Textual conventions were added for the LSR Identifier and the LDP
Identifier.
Top-level mib structure was added. The LDP MIB falls under a proposed
hierarchy of mpls.mplsProtocols.
The mib hierarchy within the LDP MIB was also changed. A new branch,
under mpls.mplsProtocols.mplsLdpMIB.mplsLdpObjects was added. This
branch is mplsLdpLsrObjects. Currently, this contains several new
scalar objects: mplsLdpLsrID, mplsLdpLsrLoopDectectionPresent,
mplsLdpLsrLoopDetectinAdminStatus, mplsLdpLsrPathVectorLimit,
mplsLdpLsrHopCountLimit, mplsLdpLsrLoopPreventionPresent,
mplsLdpLsrLoopPreventionAdminStatus, and
mplsLdpLsrLabelRetentionMode.
mplsLdpEntityTable is now indexed by mplsLdpEntityIdentifier, which
is the LDP Identifier used in Session establishment.
mplsLdpEntityLoopDetection and mplsLdpEntityLoopPrevention objects
were removed from this table.
The following objects were added to the mplsLdpEntityTable:
mplsLdpEntityLabelSpaceType, mplsLdpEntityUnlabTrafVpi,
mplsLdpEntityUnlabTrafVci, mplsLdpEntityMergeCapability,
mplsLdpEntityVcDirectionality, and
mplsLdpEntityLabelDistributionMethod.
The following objects were added to the mplsLdpPeerEntityTable:
mplsLdpPeerLabelDistributionMethod.
The following object was removed from the mplsLdpEntityStatsTable:
mplsLdpEntityEstablishedSessions.
The LIB table was added.
The following notifications were added.
References were added and revised.
6. TO DO List
This section should be removed when this document is published as an
RFC. This section outlines the next areas the authors intend to
Expires December 1999 [Page 29]
INTERNET-DRAFT MPLS LDP MIB June 1999
address.
o The MIB should be enhanced support other L2 protocols (e.g.
Frame Relay).
o Update this draft to reflect the latest changes to draft-ietf-
mpls-ldp-05.txt (or later LDP drafts).
o Update the Introduction section of the draft to reflect all the
changes made to the LDP MIB.
o Fix conformance statements.
o Remove the following sections prior to final publication: IANA
Considerations Section, Revisions Section and this (TO DO List)
Section.
7. Acknowledgments
The authors would like to thank the following people: Leigh
McLellan, Geetha Brown, Geping Chen and Charlan Zhou from Nortel
Networks, and Zoltan Takacs and Bo Augustsson from Ericsson.
Expires December 1999 [Page 30]
INTERNET-DRAFT MPLS LDP MIB June 1999
8. References
[RFC2571] Harrington, D., Presuhn, R., and B. Wijnen, "An Architecture
for Describing SNMP Management Frameworks", RFC 2571, April
1999
[RFC1155] Rose, M., and K. McCloghrie, "Structure and Identification
of Management Information for TCP/IP-based Internets", STD
16, RFC 1155, May 1990
[RFC1212] Rose, M., and K. McCloghrie, "Concise MIB Definitions", STD
16, RFC 1212, March 1991
[RFC1215] M. Rose, "A Convention for Defining Traps for use with the
SNMP", RFC 1215, March 1991
[RFC2578] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J.,
Rose, M., and S. Waldbusser, "Structure of Management
Information Version 2 (SMIv2)", STD 58, RFC 2578, April 1999
[RFC2579] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J.,
Rose, M., and S. Waldbusser, "Textual Conventions for
SMIv2", STD 58, RFC 2579, April 1999
[RFC2580] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J.,
Rose, M., and S. Waldbusser, "Conformance Statements for
SMIv2", STD 58, RFC 2580, April 1999
[RFC1157] Case, J., Fedor, M., Schoffstall, M., and J. Davin, "Simple
Network Management Protocol", STD 15, RFC 1157, May 1990.
[RFC1901] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser,
"Introduction to Community-based SNMPv2", RFC 1901, January
1996.
[RFC1906] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser,
"Transport Mappings for Version 2 of the Simple Network
Management Protocol (SNMPv2)", RFC 1906, January 1996.
[RFC2572] Case, J., Harrington D., Presuhn R., and B. Wijnen, "Message
Processing and Dispatching for the Simple Network Management
Protocol (SNMP)", RFC 2572, April 1999
[RFC2574] Blumenthal, U., and B. Wijnen, "User-based Security Model
(USM) for version 3 of the Simple Network Management
Protocol (SNMPv3)", RFC 2574, April 1999
[RFC1905] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser,
"Protocol Operations for Version 2 of the Simple Network
Management Protocol (SNMPv2)", RFC 1905, January 1996.
Expires December 1999 [Page 31]
INTERNET-DRAFT MPLS LDP MIB June 1999
[RFC2573] Levi, D., Meyer, P., and B. Stewart, "SNMPv3 Applications",
RFC 2573, April 1999
[RFC2575] Wijnen, B., Presuhn, R., and K. McCloghrie, "View-based
Access Control Model (VACM) for the Simple Network
Management Protocol (SNMP)", RFC 2575, April 1999
[RFC2570] Case, J., Mundy, R., Partain, D., and B. Stewart,
"Introduction to Version 3 of the Internet-standard Network
Management Framework", RFC 2570, April 1999
[17] Narten, T., and H. Alvestrand, "Guidelines for Writing an IANA
Considerations Section in RFCs.", RFC 2434, IBM, Maxware, October
1998
[18] Andersson, Loa, Doolan, P., Feldman, N., Fredette, A., and Thomas,
B., "LDP Specification.", draft-ietf-mpls-ldp-04.txt, Nortel
Networks, Ennovate Networks, IBM, Nortel Networks, cisco Systems
May 1999.
[19] Callon, R., Doolan, P., Feldman, N., Fredette, A., Swallow, G., and
A. Viswanathan, "A Framework for Multiprotocol Label Switching",
draft-ietf-mpls-framework-02.txt, Ascend Communications, Ennovate
Networks, IBM, Bay Networks, cisco Systems, November 1997.
[20] Rosen, E., Viswananthan, A., and R. Callon, "Multiprotocol Label
Switching Architecture", draft-ietf-mpls-arch-05.txt, cisco
Systems, Lucent Technologies, and IronBridge Networks, April 1999.
[21] Jamoussi, B., editor, "Constraint-Based LSP Setup using LDP",
draft-ietf-mpls-cr-ldp-01.txt, February 1999.
[22] Bradner, S., "Key words for use in RFCs to Indicate Requirement
Levels", BCP 14, RFC 2119, Harvard University, March 1997
[23] Bradner, S., "The Internet Standards Process -- Revision 3", BCP 9,
RFC 2026, Harvard University, October 1996
[24] Srinivansan, C., and A. Viswanathan, "MPLS Traffic Engineering
Management Information Base Using SMIv2", draft-ietf-mpls-te-mibs-
00.txt, Lucent Technologies, February 1999.
[25] Greene, M., J. Cucchiara, J. Luciani, "Definition of Managed
Objects for the NBMA Next Hop Resolution Protocol (NHRP)", draft-
ietf-ion-nhrp-mib-09.txt, May 1999.
Expires December 1999 [Page 32]
INTERNET-DRAFT MPLS LDP MIB June 1999
9. Security Considerations
Assuming that secure network management (such as SNMP v3) is
implemented, the objects represented in this MIB do not pose a threat
to the security of the network.
10. Authors' Addresses
Joan Cucchiara
IronBridge Networks
55 Hayden Ave., Suite 1000
Lexington, MA 02421
Phone: (781) 372-8236
Email: joan@ironbridgenetworks.com
Hans Sjostrand
Ericsson
Business Unit Datacom Networks and IP Services
S-126 25 Stockholm, Sweden
Phone: +46 8 719 9960
Email: hans.sjostrand@etx.ericsson.se
James V. Luciani
Nortel Networks
3 Federal Street
Mail Stop: BL3-03
Billerica, MA 01821
Phone: (978) 916-4734
Email: luciani@baynetworks.com
11. Full Copyright Statement
Copyright (C) The Internet Society (1999). All Rights Reserved.
This document and translations of it may be copied and furnished to
others, and derivative works that comment on or otherwise explain it
or assist in its implementation may be prepared, copied, published
and distributed, in whole or in part, without restriction of any
kind, provided that the above copyright notice and this paragraph are
included on all such copies and derivative works. However, this
document itself may not be modified in any way, such as by removing
the copyright notice or references to the Internet Society or other
Expires December 1999 [Page 33]
INTERNET-DRAFT MPLS LDP MIB June 1999
Internet organizations, except as needed for the purpose of
developing Internet standards in which case the procedures for
copyrights defined in the Internet Standards process must be
followed, or as required to translate it into languages other than
English.
The limited permissions granted above are perpetual and will not be
revoked by the Internet Society or its successors or assigns.
This document and the information contained herein is provided on an
"AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
12. IANA Address Family Numbers MIB
This section is copied verbatim from the draft-ietf-ion-nhrp-mib-
09.txt[]. This section will be removed in future versions of this
draft. This section was copied here to for convenience, as it is
IMPORTED into the LDP MIB.
This appendix defines the initial content of the IANA-ADDRESS-
FAMILY-NUMBERS-MIB. This section should be removed from this
document prior to its approval, at which time this MIB will be
administered by IANA.
The branch for this MIB needs to be determined, and an appropriate
number should be added where XXX is currently.
IANA-ADDRESS-FAMILY-NUMBERS-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY,
mib-2 FROM SNMPv2-SMI
TEXTUAL-CONVENTION FROM SNMPv2-TC;
ianaAddressFamilyNumbers MODULE-IDENTITY
LAST-UPDATED "9905191200Z" -- May 19, 1999
ORGANIZATION "IANA"
CONTACT-INFO
"Postal: Internet Assigned Numbers Authority
USC/Information Sciences Institute
4676 Admiralty Way
Marina del Rey, CA 90292-6695
USA
Expires December 1999 [Page 34]
INTERNET-DRAFT MPLS LDP MIB June 1999
Tel: +1 310-822-1511
E-Mail: iana@isi.edu"
DESCRIPTION
"The MIB module defines the AddressFamilyNumbers
textual convention."
-- revision history
REVISION "9905191200Z" -- May 19, 1999
-- RFC-Editor assigns RFC xxxx
DESCRIPTION "Initial version, published as RFC xxxx."
::= { mib-2 XXX } -- to be assigned by IANA
AddressFamilyNumbers ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The definition of this textual convention with the
addition of newly assigned values is published
periodically by the IANA, in either the Assigned
Numbers RFC, or some derivative of it specific to
Internet Network Management number assignments.
(The latest arrangements can be obtained by
contacting the IANA.)
The enumerations are described as:
other(0), -- none of the following
ipV4(1), -- IP Version 4
ipV6(2), -- IP Version 6
nsap(3), -- NSAP
hdlc(4), -- (8-bit multidrop)
bbn1822(5),
all802(6), -- (includes all 802 media
-- plus Ethernet 'canonical format')
e163(7),
e164(8), -- (SMDS, Frame Relay, ATM)
f69(9), -- (Telex)
x121(10), -- (X.25, Frame Relay)
ipx(11), -- IPX (Internet Protocol Exchange)
appletalk(12), -- Apple Talk
decnetIV(13), -- DEC Net Phase IV
banyanVines(14), -- Banyan Vines
e164withNsap(15),
-- (E.164 with NSAP format subaddress)
reserved(65535)
Expires December 1999 [Page 35]
INTERNET-DRAFT MPLS LDP MIB June 1999
Requests for new values should be made to IANA via
email (iana@isi.edu)."
SYNTAX INTEGER {
other(0),
ipV4(1),
ipV6(2),
nsap(3),
hdlc(4),
bbn1822(5),
all802(6),
e163(7),
e164(8),
f69(9),
x121(10),
ipx(11),
appletalk(12),
decnetIV(13),
banyanVines(14),
e164withNsap(15),
reserved(65535)
}
END
Expires December 1999 [Page 36]
INTERNET-DRAFT MPLS LDP MIB June 1999