Viewlogic Interface - Software Setup

M1 with Workview Office on a PC

M1 with Powerview on a Workstation

XACTstep 6.0.x with Workview Office/PROseries on a PC

XACTstep 5.2.x with Powerview on a Workstation

M1 Setup on a PC

In this example, The Xilinx M1 Core Tools have been installed for Windows 95 or NT 4.0 in C:\XILINX. Workview Office 7.3 or greater has been installed in C:\WVOFFICE. Please substitute the appropriate directory paths that apply to your own system.

To run Xilinx M1 software with the Viewlogic Interface, the following environment variables must be set in your AUTOEXEC.BAT (Windows 95) or in the System Environment Control Panel (Windows NT 4.0):

SET XILINX=C:\XILINX SET PATH=C:\XILINX\BIN\NT;C:\WVOFFICE;%PATH% SET WDIR=C:\WVOFFICE\STANDARD SET LM_LICENSE_FILE=C:\WVOFFICE\STANDARD\LICENSE.DAT,;C:\FLEXLM\LICENSE.DAT¹

SET VANTAGE_VSS=C:\WVOFFICE\V SET VANTAGE_CC=C:\WVOFFICE\CL

¹ Note that the delimiter is comma-semicolon (,;) for Workview Office 7.31 or older. For Workview Office 7.4, the delimiter is just a semicolon (;).

M1 Setup on a Workstation

In this example, The Xilinx M1 Core Tools have been installed for Solaris 2.5 in /tools/xilinxM1. The Viewlogic Interface is part of the Xilinx M1 tree under $XILINX/viewlog. The Viewlogic vendor software (where Powerview is located) has been installed in /tools/powerview6. Please substitute the appropriate directory paths that apply to your own system. Also, if you are running the tools under HP-UX or SunOS 4.1.x, please substitute hp or sun for sol where appropriate.

To run Xilinx M1 software with the Viewlogic Interface, the following environment variables must be set:

setenv XILINX /tools/xilinxM1 setenv PVIEW¹ /tools/powerview6 setenv MYPVIEW¹ ${HOME} (or some other writeable directory)

setenv WDIR $XILINX/viewlog/data/logiblox/standard:${MYPVIEW}:${PVIEW}/standard setenv VANTAGE_VSS ${PVIEW}/standard/van_vss setenv LM_LICENSE_FILE² /usr/license/viewlogic_license.dat:${XILINX}/data/license.dat³

set path = ( ${XILINX}/bin/sol ${PVIEW} ${VANTAGE_VSS}/pgm/dir $path )

For SunOS/Solaris only:
setenv LD_LIBRARY_PATH² ${PVIEW}/standard/fusion:/usr/ucblib:${XILINX}/bin/sol

For HP-UX only:
setenv SHLIB_PATH² ${PVIEW}/standard/fusion:${XILINX}/bin/hp

¹ Powerview does not require these, but other variables are defined in these terms.
² If already set, concatenate this path with existing one(s), separated by a colon (:).
³ Set these paths to the locations of the appropriate license files.

XACT 6.0.x Setup on a PC

In this example, The XACT 6.0.x Core Tools (DS502) have been installed for Windows 3.11 or 95 in C:\XACT. The Viewlogic Interface (DS391) has been installed in C:\WVOFFICE. Workview Office 7.1.2 or newer has been installed in C:\WVOFFICE. Please substitute the appropriate directory paths that apply to your own system.

To modify these settings to use the PROseries tools instead of Workview Office, change all the C:\WVOFFICE references to C:\PROSER.
For Windows 3.11, Workview Office 7.1.2 only or PROseries 6.1 must be used.
For Windows 95, Workview Office 7.2 or greater must be used.
For Windows NT, XACT 6.0.x is not supported.

To run XACT 6.0.x software with the Viewlogic Interface, the following environment variables must be set in your AUTOEXEC.BAT:

SET XACT=C:\XACT;C:\WVOFFICE SET PATH=C:\XACT;C:\WVOFFICE;%PATH% SET WDIR=C:\WVOFFICE\STANDARD

Workview Office only:
SET LM_LICENSE_FILE=C:\WVOFFICE\STANDARD\LICENSE.DAT SET VANTAGE_VSS=C:\WVOFFICE\STANDARD\V¹ SET VANTAGE_CC=C:\WVOFFICE\MSVCNT\BIN\CL¹

¹ For these variables for Workview Office 7.3 and newer, refer to the M1 PC setup below.

For detailed information about running Workview Office with XACTstep 6.0, click here.

XACT 5.2.x Setup on a Workstation

In this example, The XACT 5.2.x Core Tools (DS502) have been installed for SunOS 4.1.x in /tools/xact521/ds502. The Viewlogic Interface (DS391) has been installed in /tools/xact521/ds391. The Viewlogic vendor software (where Powerview is located) has been installed in /tools/powerview6. Please substitute the appropriate directory paths that apply to your own system.

To run XACT 5.2.x software with the Viewlogic Interface, the following environment variables must be set:

setenv DS391 /tools/xact521/ds391 setenv XACT ${DS391}:/tools/xact521/ds502

setenv PVIEW¹ /tools/powerview6 setenv MYPVIEW¹ ${HOME} (or some other writeable directory)

setenv WDIR ${MYPVIEW}:${PVIEW}/standard setenv VANTAGE_VSS ${PVIEW}/standard/van_vss setenv LM_LICENSE_FILE² /usr/local/data/license/viewlogic_license.dat³

set path = ( $DS391/bin/sparc /tools/xact/ds502/bin/sparc ${PVIEW} ${VANTAGE_VSS}/pgm/dir $path )

For SunOS/Solaris only:
setenv LD_LIBRARY_PATH² ${PVIEW}/standard/fusion

For HP-UX only:
setenv SHLIB_PATH² ${PVIEW}/standard/fusion

¹ Powerview does not require these, but other variables are defined in these terms.
² If already set, concatenate this path with existing one(s), separated by a colon (:).
³ Set this path to the location of the Viewlogic license file.


	Trademarks and Patents Legal Information Privacy Policy