Subject: RE: [sv-cc] VPIs for changing the log file..
From: David W. Smith (david.smith@synopsys.com)
Date: Tue Apr 15 2003 - 09:31:08 PDT
This truly sounds like an issue that should be sent to the IEEE 1364
committee. They are the owner of errata and enhancements like this. You may
want to contact Cliff Cummings at Sunburst-Design.
(cliffc@sunburst-design.com).
The only work that Accellera is doing with VPI is in extending it to support
the SystemVerilog extensions.
Regards
David
David W. Smith
Synopsys Scientist
Synopsys, Inc.
Synopsys Technology Park
2025 NW Cornelius Pass Road
Hillsboro, OR 97124
Voice: 503.547.6467
Main: 503.547.6000
FAX: 503.547.6906
Email: david.smith@synopsys.com
http://www.synopsys.com
-----Original Message-----
From: owner-sv-cc@eda.org [mailto:owner-sv-cc@eda.org] On Behalf Of
Raghuraman R
Sent: Monday, April 14, 2003 8:39 PM
To: Joao.Geada@Synopsys.COM
Cc: sv-cc@eda.org
Subject: Re: [sv-cc] VPIs for changing the log file..
Joao,
Thanks for the response.
So, there is no solution to change the log file midway during a
simulation. With whom should this issue be taken up? Should VPI be
enhanced or is it a problem of the simulator vendor and hence the issue
to be taken up with him only?
Thanks.
Joao Geada wrote:
> Raghuraman,
>
> as far as I am aware, VPI is currently forbidden to manipulate the log
> file in use by the simulator (this is implicitly described in IEEE
> 1364-2001, section 27.22, vpi_mcd_close)
>
> Specifically, there is an mcd channel describing the simulator log
> file, but vpi cannot modify that stream (ie cannot close the current
> stream and then reopen it to a different file)
>
> However, I believe you can get the name of the log file from
> vpi_mcd_name (use channel descriptor 1 to get the log file)
>
> Joao
>
============================================================================
==
> Joao Geada, PhD Principal Engineer Verif Tech
Group
> Synopsys, Inc TEL: (508)
263-8083
> 377 Simarano Drive, Suite 300, FAX: (508)
263-8069
> Marlboro, MA 01752, USA
> ======================================================================
> ========
>
>
> -----Original Message-----
> From: owner-sv-cc@eda.org [mailto:owner-sv-cc@eda.org]On Behalf Of
> Raghuraman R
> Sent: Friday, April 11, 2003 4:24 AM
> To: sv-cc@eda.org
> Subject: [sv-cc] VPIs for changing the log file..
>
>
> Hi,
>
> I would like to know if there is any vpi call to change the logfile
> during simulation. I know of the vpi_mcd_* calls but it is for any
> user-specific displays.
>
> For example, if I am running a big simulation job running for 48
> hours,
> then the log file that gets generated is a 16 GB file or so which cannot
> be edited or read easily. So if there is a vpi call to change the log
> file, it will be good for the users, who can look at the smaller log
> files. This is also needed when multiple vector files are simulated in
> one run and users would like to have one log for each file.
>
> The prototype could be
>
> int vpi_change_log("<file name>", mode (append|write));
>
> Similarly there should be a call to get the current log file name
>
> char * vpi_get_logfilename();
>
> Otherwise, logfile could be declared as an object which can be edited
> using the vpi_put_value and value obtained through vpi_get_value. The
> object type could be enumerated on the types of vpiBinStrVal etc.
-- Regds,Raghuraman R ASIC Texas Instruments (India) Ltd. Phone : +91-80-5099113 http://www.india.ti.com/~raghu
* Think. *
This archive was generated by hypermail 2b28 : Tue Apr 15 2003 - 09:29:31 PDT